Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REENTRY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

A space qualified radiation source holder

A radiation source holder was developed to permit controlled exposure of biological material to a gamma-emitting radiation source during flight in a recoverable earth-orbiting satellite. A unique spring drive mechanism, activated by real time commands from the ground station, moved the Sr-85 source from a shielded position to the exposed position and then back to the shielded condition before reentry and recovery. A fail-safe feature utilized the reentry deceleration force to ensure that the source would be in a shielded position during the recovery operations. The device was successfully flown on Biosatellite 2.

Polaski, L. J.↗

Sonic-boom ground-pressure measurements from Apollo 15

Sonic boom pressure signatures recorded during the launch and reentry phases of the Apollo 15 mission are presented. The measurements were obtained along the vehicle ground track at 87 km and 970 km downrange from the launch site during ascent; and at 500 km, 55.6 km, and 12.9 km from the splashdown point during reentry. Tracings of the measured signatures are included along with values of the overpressure, impulse, time duration, and rise times. Also included are brief descriptions of the launch and recovery test areas in which the measurements were obtained, the sonic boom instrumentation deployment, flight profiles and operating conditions for the launch vehicle and spacecraft, surface weather information at the measuring sites, and high altitude weather information for the general measurement areas.

Hilton, D. A.↗

Flight and ground tests of a very low density elastomeric ablative material

A very low density ablative material, a silicone-phenolic composite, was flight tested on a recoverable spacecraft launched by a Pacemaker vehicle system; and, in addition, it was tested in an arc heated wind tunnel at three conditions which encompassed most of the reentry heating conditions of the flight tests. The material was composed, by weight, of 71 percent phenolic spheres, 22.8 percent silicone resin, 2.2 percent catalyst, and 4 percent silica fibers. The tests were conducted to evaluate the ablator performance in both arc tunnel and flight tests and to determine the predictability of the albator performance by using computed results from an existing one-dimensional numerical analysis. The flight tested ablator experienced only moderate surface recession and retained a smooth surface except for isolated areas where the char was completely removed, probably following reentry and prior to or during recovery. Analytical results show good agreement between arc tunnel and flight test results. The thermophysical properties used in the analysis are tabulated.

Olsen, G. C.↗

In-flight angular alignment of inertial navigation systems by means of radio aids

The principles involved in the angular alignment of the inertial reference by nondirectional data from radio aids are developed and compared with conventional methods of alignment such as gyro-compassing and pendulous vertical determination. The specific problem is considered of the space shuttle reentry and a proposed technique for the alignment of the inertial reference system some time before landing. A description is given of the digital simulation of a transponder interrogation system and of its interaction with the inertial navigation system. Data from reentry simulations are used to demonstrate the effectiveness of in-flight inertial system alignment. Concluding remarks refer to other potential applications such as space shuttle orbit insertion and air navigation of conventional aircraft.

Tanner, W.↗

Oxidation at through-hole defects in fused slurry silicide coated columbium alloys FS-85 and Cb-752

Metal recession and interstitial contamination at 0.08-centimeter-diameter through-hole intentional defects in fused slurry silicide coated FS-85 and Cb-752 columbium alloys were studied to determine the tolerance of these materials to coating defects. Five external pressure reentry simulation exposures to 1320 C and 4.7 x 1,000 N/sq m (maximum pressure) resulted in a consumed metal zone having about twice the initial defect diameter for both alloys with an interstitial contamination zone extending about three to four initial defect diameters. Self-healing occurred in the 1.33 x 10 N/sq m, 1320 C exposures and to a lesser extent in internal pressure reentry cycles to 1320 C and 1.33 x 100 N/sq m (maximum pressure).

Levine, S. R.↗

Development of a closed pore insulation material

A closed pore ceramic foam insulation material (CPI) has been developed that offers possibilities for use as a reusable external heat shield for the NASA manned space shuttle. The outstanding characteristics of CPI are: (1) negligible water absorption due to a noninterconnecting network of cells; (2) high emittance at room and elevated temperature; (3) ability to survive at least 10 simulated reentry cycles to 1500 K using radiant heat lamps to simulate the reentry heat fluxes; (4) ability to survive, with no change in properties or appearance, at least 10 simulated plasma arc jet cycles to 1500 K (with the exception of some stress cracks induced either by the unduly severe nature of the initial arc splash heating pulse or by improper mechanical holding of the specimen in the test fixture); (5) strength (flexure); and (6) a low thermal conductivity throughout the temperature range of interest for the space shuttle.

Tobin, A.↗

The thermal and mechanical properties of a low density elastomeric ablation material

Thermal and mechanical properties data were obtained for a low density elastomeric resin based ablation material with phenolic-glass honeycomb reinforcement. Data were obtained for the material in the charred and uncharred state. Ablation material specimens were charred in a laboratory furnace at temperatures in the range from 600 K to 1700 K to obtain char specimens representative of the ablation char layer formed during reentry. These specimens were then used to obtain effective thermal conductivity, heat capacity, porosity, and permeability data at the char formation temperature. This provided a boxing of the data which enables the prediction of the transient response of the material during ablation. Limited comparisons were made between the furnace charred specimens and specimens which had been exposed to simulated reentry conditions.

Engelke, W. T.↗

Recovery of sounding rocket payloads by center-of-gravity position control.

A computerized procedure has been developed to predict dynamic pressure at parachute deployment altitude. Inputs to the program are payload geometry, center-of-gravity position, velocity, and altitude at start of reentry. Payload is assumed to be trimmed, and potential and cross-flow drag theory is used to compute trim angle-of-attack and trim drag coefficient as a function of free-stream Mach number. The computations involve only simple geometric quantities and closed-form equations. Payload flight path is assumed to be vertical, and equations of motion of the payload are integrated from start of reentry to chute deployment altitude.

Mcgarvey, J. F.↗

Atmosphere-entry behavior of a modular, disk-shaped, isotope heat source.

The authors have studied the entry and impact behavior of an isotope heat source for space nuclear power that disassembles into a number of modules which would enter the earth's atmosphere separately if a flight aborted. These modules are disk-shaped units, each with its own reentry heat shield and protective impact container. In normal operation, the disk modules are stacked inside the generator, but during a reentry abort they separate and fly as individual units of low ballistic coefficient. Flight tests at hypersonic speeds have confirmed that a stack of disks will separate and assume a flat-forward mode of flight. Free-fall tests of single disks have demonstrated a nominal impact velocity of 30 m/sec at sea level for a practical range of ballistic coefficients.

Vorreiter, J. W.↗

A study of RSI under combined stresses

The behavior of typical rigidized surface insulation material (RSI) under combined loading states was investigated. In particular, the thermal stress states induced during reentry of the space shuttle were of prime concern. A typical RSI tile was analyzed for reentry thermal stresses under computed thermal gradients for a model of the RSI material. The results of the thermal stress analyses were then used to aid in defining typical combined stress states for the failure analysis of RSI.

Kibler, J. J.↗

Fluctuating surface pressure characteristics on slender cones in subsonic, supersonic, and hypersonic Mach-number flow

A program is presented to determine the flow-induced unsteady aerodynamic loads on space-shuttle orbiter configurations in the early reentry phase. Experiments on 8 degree half-angle cone/flat-base configurations were conducted at free-stream Mach numbers of 6 and 15 and Reynolds numbers corresponding to shuttle reentry. Data are available at free-stream Mach-numbers of 0.67, 2.5, 3, 4, 6, 15, and 22. It is shown that empirical expressions could be developed for the Mach-number dependence of the overall fluctuation pressure under an attached turbulent boundary layer and under a separated base-flow region.

Heller, H. H.↗

Measurements of sonic-boom overpressures from Apollo space vehicles

This paper presents representative results of sonic-boom overpressure data recorded during the launch and reentry of the Apollo 15 and 16 space vehicle systems. Comparisons are made between measured overpressures and those predicted using available theory. The measurements were obtained along the vehicle ground track at 68, 87, 92, 129, and 970 km downrange from the launch site during ascent, and at 9, 13, 55, 185, and 500 km from the splash-down point during reentry. Also included are tracings of the sonic-boom signatures along with a brief description of the launch and recovery test areas in which the measurements were obtained, the sonic-boom instrumentation deployment, flight profiles and operating conditions, and high-altitude weather information for the general measurement areas.

Hilton, D. A.↗

Cost Modeling Techniques for Design Maturity

Cost modeling techniques and factors which either add to or subtract from these estimates are examined. The most important factors for increasing costs are interfacing subsystems, subsystem design and software maturity. Cost decrease depends on hardware, software, and support equipment availability. A cost modeling analysis for reentry shield and aerodynamic decelerator subsystems of a reentry vehicle is presented. Integration problems for the subsystems are also discussed.

Ruhland, E. W.↗

Shuttle communications design study

The design and development of a space shuttle communication system are discussed. The subjects considered include the following: (1) Ku-band satellite relay to shuttle, (2) phased arrays, (3) PN acquisition, (4) quadriplexing of direct link ranging and telemetry, (5) communications blackout on launch and reentry, (6) acquisition after blackout on reentry, (7) wideband communications interface with the Ku-Band rendezvous radar, (8) aeroflight capabilities of the space shuttle, (9) a triple multiplexing scheme equivalent to interplex, and (10) a study of staggered quadriphase for use on the space shuttle.

Cartier, D. E.↗

SERV - A reusable single stage to orbit space shuttle concept

Feasibility studies were made on the SERV (Single-stage Earth-orbital Reusable Vehicle), which is a single-stage, fully reusable space shuttle concept. The studies show that a reusable single-stage-to-orbit shuttle can be built using present technology. The SERV satisfies all of NASA's requirements for low earth orbital and space station resupply missions. The baseline vehicle has a modified Apollo external configuration, 90 ft in diameter and 66 ft in height, with a cargo hold 23 ft in diameter and 60 ft long. Take-off is vertical, powered by an integral aerospike rocket engine. An Apollo-type ballistic reentry profile is used, and precision vertical landing is possible with power provided by an array of turbojet engines. The key feasibility issues discussed are engine performance, aerodynamic drag, subsystem weights, method and type of thermal protection during reentry, descent aerodynamic characteristics, and landing method.

Tharratt, C. E.↗

An experimental summary of plasma arc exposures of space shuttle high-temperature reusable surface insulation tile array with a single missing tile (conducted at the Ames Research Center)

A space shuttle high temperature reusable surface insulation (HRSI) tile array with a single missing or lost tile was exposed to a hot gas simulated reentry environment to investigate the heating conditions in and around the vicinity of the missing HRSI tile. Heat flux and pressure data for the lost tile condition were obtained by the use of a water cooled lost tile calibration model. The maximum aluminum substrate temperature obtained during the simulated reentry was 128 C (263 F). The lost tile calibration data indicated a maximum heat flux in the lost tile cavity region of 63 percent of the upstream reference value. This test was conducted at the Ames Research Center in the 20 MW semielliptical thermal protection system (TPS) pilot plasma arc test facility.

Galanter, S. A.↗

Aerothermal performance and structural integrity of a Rene 41 thermal protection system at Mach 6.6

A flightweight panel based on a metallic thermal-protection-system concept for hypersonic and reentry vehicles was subjected repeatedly to thermal cycling by quartz-lamp radiant heating using a thermal history representative of a reentry heat pulse and to aerodynamic heating at heating rates required to sustain a surface temperature of 1089 K (1960 R). The panel consisted of a corrugated heat shield and support members of 0.05-cm (0.02-in.) thick Rene 41 of riveted construction and 5.08-cm (2-in.) thick silica fibrous insulation packages covered by Rene 41 foil and inconel screening. All tests were conducted in the Langley 8-foot high-temperature structures tunnel with the heat shield corrugations alined in the stream direction. The panel sustained 5.33 hr of intermittent radiant heating and 6.5 min of intermittent aerodynamic heating of up to 1-min duration for differential pressures up to 6.2 kPa (0.9 psi) with no apparent degradation of thermal or structural integrity, as indicated by temperature distributions and results from load deflection tests and vibration surveys of natural frequencies.

Deveikis, W. D.↗

Fundamental studies on the nature and properties of ceramic fiber insulation

Silica and mullite fibers used to fabricate reusable surface insulation (RSI) for the space shuttle orbiter may devitrify/recrystallize within the temperature range anticipated upon reentry. This is shown to be dependent upon impurity level, temperature, and time at temperature. It is determined that the effects of the material improvement and optimization program are positive. The degree of crystallinity is shown to have a predominant effect upon the strength of fabricated RSI tile, and limits are determined. Models are developed to predict tensile strengths and shrinkage rates of silica tile based upon readily measurable parameters. Thermal cycling which simulates reentry results in an increase in the crystallinity and in the porosity of tile coatings.

Mueller, J. I.↗