Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Parameter identification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

On-Orbit Cross Calibration Between the Osiris-Rex Orbiting Laser Altimeter and Navigation Camera

Accurate shape models of small bodies provide both science value and resources for precision relative navigation. One instrument commonly used for generating shape models is the laser altimeter. Laser altimeters require accurate intrinsic and extrinsic calibration knowledge to produce accurate shape models. Here, we describe a method used for updating the intrinsic and extrinsic calibration parameters of the laser altimeter onboard the Origins, Spectral Interpretation, Resource Identification, and Security–Regolith Explorer (OSIRIS-REx) spacecraft, OLA (OSIRISREx Laser Altimeter). We perform the calibration update by comparing the OLA scans with monocular camera images of the asteroid surface captured by the primary navigation camera.

Andrew J. Liounis↗
NASA NTRS1980

A line parameter list for the nu2 and nu4 bands of /C-12/H4 and /C-13/H4, extended to J-prime = 25 and its application to planetary atmospheres

Line parameters (transition frequencies, line strengths, line widths, ground state energies and quantum identifications) for the nu2 and nu4 bands of (C-12)H4 and (C-13)H4 have been calculated for J-prime equal to or less than 25 using the simultaneous coupled fitting procedure of Gray and Robiette. Molecular constants for the nu2 band of (C-13)H4 were estimated from isotopic shifts from (C-12)H4 values. Agreement with laboratory spectra, where available, is always well within 1 kayser over the entire spectral range covered by the list. The most serious problem in comparison with laboratory data is the omission of lines belonging to 'hot' bands in this spectral region. This list is valuable in remote sensing problems for sorting out lines of trace species from weak methane lines and for determining the atmospheric opacity in relatively transparent spectral regions. Applications of the parameter list are demonstrated for remote sounding of the Jovian atmosphere.

Orton, G. S.↗
NASA NTRS1984

Model estimation and identification of manual controller objectives in complex tracking tasks

A methodology is presented for estimating the parameters in an optimal control structural model of the manual controller from experimental data on complex, multiinput/multioutput tracking tasks. Special attention is devoted to estimating the appropriate objective function for the task, as this is considered key in understanding the objectives and strategy of the manual controller. The technique is applied to data from single input/single output as well as multi input/multi outpuut experiments, and results discussed.

Schmidt, D. K.↗
NASA NTRS1987

Maximum likelihood identification using an array processor

Maximum likelihood estimation (MLE) is a method used to calculate the parameters of a dynamic system. It can be applied to a large class of problems and has good statistical properties. The main disadvantage of the MLE method is the amount of computation required. This paper describes how the computation time can be reduced significantly by using an array processor. The estimation of the parameters of a dynamic model of the Space Station is used as an example to evaluate the method.

Sridhar, Banavar↗
NASA NTRS2005

Identification of atypical flight patterns

Method and system for analyzing aircraft data, including multiple selected flight parameters for a selected phase of a selected flight, and for determining when the selected phase of the selected flight is atypical, when compared with corresponding data for the same phase for other similar flights. A flight signature is computed using continuous-valued and discrete-valued flight parameters for the selected flight parameters and is optionally compared with a statistical distribution of other observed flight signatures, yielding atypicality scores for the same phase for other similar flights. A cluster analysis is optionally applied to the flight signatures to define an optimal collection of clusters. A level of atypicality for a selected flight is estimated, based upon an index associated with the cluster analysis.

Statler, Irving C.↗
NASA NTRS2020

Aircraft System Identification from Multisine Inputs and Frequency Responses

A frequency-domain approach is described for estimating parameters, such as stability and control derivatives, in aircraft flight dynamic models from measured input and output data. The approach uses orthogonal phase-optimized multisines for moving the aircraft control effectors, Fourier analysis for computing multiple-input multiple-output frequency responses, and a maximum likelihood estimator called frequency response error (FRE) for determining values and uncertainties for the model parameters. The approach is demonstrated using flight test data for two subscale airplanes: the T-2 generic transport model and the X-56A aeroelastic demonstrator. Results and comparisons with the output-error method indicated that the approach produced accurate estimates of stability and control derivatives and their uncertainties from flight test data.

Grauer, Jared A.↗
NASA NTRS1988

On-orbit parametric identification methodology

On-orbit system identification (ID) of large space systems is essential for various reasons. For example, the complex composite structure of such systems cannot be ground-tested; their structural dynamic characteristics must be known accurately in order to accomplish active control. Furthermore, such capability can be used to characterize/identify various disturbances. The identification process is consisted of four principal elements: (1) modeling, (2) the estimation algorithm, (3) input system, and (4) measurement system. These elements are highly correlated and all togerher determine the success of the identification problem. Accurate modeling of large space systems is the most important element of the identification process. Large flexible structures are non-linear and infinite dimensional systems with highly coupled parameters and low frequency packed modes. In addition, these systems are subject to stochastic and time-varying disturbances, they have structural parameters which can vary due to on-orbit assembly deployment, and operations. These systems are generally; however, represented by constant coefficient, finite order differential equations. The non-linearities, coupling and noise effects are also often neglected. Moreover, identification experiment designs which lead to highly complex optimization problems usually require the simultaneous choice of ID algorithm, sensor, and actuator type and placement. On-orbit bandwidth and power restrictions on excitation, limited data window, and restrictions on sensor/actuator type, placement and number, has led to practical questions of implementations.

Hadaegh, Fred Y.↗
NASA NTRS2018

Real-Time Adaptive Drag Minimization Wind Tunnel Investigation of a Flexible Wing with Variable Camber Continuous Trailing Edge Flap System

This paper reports the results of a recently completed real-time adaptive drag minimization wind tunnel investigation of a highly flexible wing wind tunnel model equipped with the Variable Camber Continuous Trailing Flap (VCCTEF) technology at the University of Washington Aeronautical Laboratory (UWAL). The wind tunnel investigation is funded by NASA SBIR Phase II contract with Scientific Systems Company, Inc. (SSCI) and University of Washington (UW) as a subcontractor. The wind tunnel model is a sub-scale Common Research Model (CRM) wing constructed of foam core and fiberglass skin and is aeroelastically scaled to achieve a wing tip deflection of 10% of the wing semi-span which represents a typical wing tip deflection for a modern transport such as Boeing 787. The jig-shape twist of the CRM wing is optimized using a CART3D aero-structural model to achieve the minimum induced drag for the design cruise lift coefficient of 0.5. The wing is equipped with two chord wise cambered segments for each of the six span wise flap sections for a total of 12 individual flap segments that comprise the VCCTEF system. Each of the 12 flap segments is actively controlled by an electric servo-actuator. The real-time adaptive drag optimization strategy includes an on-board aerodynamic model identification, a model excitation, and a real-time drag optimization. The on-board aerodynamic model is constructed parametrically as a function of the angle of attack and flap positions to model the lift and drag coefficients of the wing. The lift coefficient models include a linear model and a second-order model. The drag coefficient models include a quadratic model and a higher-order up to 6th-order model to accurately model the drag coefficient at high angles of attack. The onboard aerodynamic model identification includes a recursive least-squares (RLS) algorithm and a batch least-squares (BLS) algorithm designed to estimate the model parameters. The model excitation method is designed to sample the input set that comprises the angle of attack and the flap positions. Three model excitation methods are developed: random excitation method, sweep method, and iterative angle-of-attack seeking method. The real-time drag optimization includes a generic algorithm developed by SSCI and several optimization methods developed by NASA which include a second-order gradient Newton-Raphson optimization method, an iterative gradient optimization method, a pseudo-inverse optimization method, an analytical optimization method, and an iterative refinement optimization method. The first wind tunnel test entry took place in September 2017. This test revealed major hardware issues and required further redesign of the flap servo mechanisms. The second test entry took place in April 2018. However, the test was not successful due to the issues with the onboard aerodynamic model identification RLS algorithm which incorrectly identified model parameters. This test also provides an experimental comparison study between the VCCTEF and a variable camber discrete trailing edge flap (VCDTEF) without the elastomer transition mechanisms. The experimental result confirms the benefit of the VCCTEF which produces lower drag by 5% than the VCDTEF. The third and final test entry took place in June 2018 after the issues with the RLS algorithm have been identified and corrected. Additional improvements were implemented. These include the BLS algorithm, the iterative angle-of-attack seeking method, the iterative gradient optimization method, and the pseudo-inverse optimization method. The test objectives were successfully demonstrated as the real-time drag optimization identifies several optimal solutions at off-design lift coefficients. The iterative gradient optimization method is found to achieve up to 4.7% drag reduction for the off-design lift coefficient of 0.7. The pseudo-inverse optimization method which does not require the drag coefficient model is found to be quite effective in reducing drag. Up to 9.4% drag reduction for the off-design lift coefficient of 0.7 is achieved with the pseudo-inverse optimization method. The wind tunnel investigation demonstrates the potential of real-time drag optimization technology. Several new capabilities are developed that could enable future adaptive wing technologies for flexible wings equipped with drag control devices such as the VCCTEF.

Drag Optimization↗
NASA NTRS2000

Modal Analysis and Model Correlation of the Mir Space Station

This paper will discuss on-orbit dynamic tests, modal analysis, and model refinement studies performed as part of the Mir Structural Dynamics Experiment (MiSDE). Mir is the Russian permanently manned Space Station whose construction first started in 1986. The MiSDE was sponsored by the NASA International Space Station (ISS) Phase 1 Office and was part of the Shuttle-Mir Risk Mitigation Experiment (RME). One of the main objectives for MiSDE is to demonstrate the feasibility of performing on-orbit modal testing on large space structures to extract modal parameters that will be used to correlate mathematical models. The experiment was performed over a one-year span on the Mir-alone and Mir with a Shuttle docked. A total of 45 test sessions were performed including: Shuttle and Mir thruster firings, Shuttle-Mir and Progress-Mir dockings, crew exercise and pushoffs, and ambient noise during night-to-day and day-to-night orbital transitions. Test data were recorded with a variety of existing and new instrumentation systems that included: the MiSDE Mir Auxiliary Sensor Unit (MASU), the Space Acceleration Measurement System (SAMS), the Russian Mir Structural Dynamic Measurement System (SDMS), the Mir and Shuttle Inertial Measurement Units (IMUs), and the Shuttle payload bay video cameras. Modal analysis was performed on the collected test data to extract modal parameters, i.e. frequencies, damping factors, and mode shapes. A special time-domain modal identification procedure was used on free-decay structural responses. The results from this study show that modal testing and analysis of large space structures is feasible within operational constraints. Model refinements were performed on both the Mir alone and the Shuttle-Mir mated configurations. The design sensitivity approach was used for refinement, which adjusts structural properties in order to match analytical and test modal parameters. To verify the refinement results, the analytical responses calculated using original and refined math models were compared with the measured responses. The results from this study show that the refined models predict more accurately the dynamics of the actual structure. The MiSDE test and analysis results provided the information and experience on test design, flight testing, and data analysis for the ISS and other future spacecraft, which are critical to the verification of analytical models and structural loads.

Kim, Hyoung M.↗
NASA NTRS1985

A Nonlinear Dual-Adaptive Control Strategy for Identification and Control of Flexible Structures

A technique is presented for obtaining a control law to regulate the modal dynamics and identify the modal parameters of a flexible structure. The method is based on using a min-max performance index to derive a control law which may be considered to be a best compromise between optimum one step control and identification inputs. Features of the approach are demonstrated by a computer simulation of the controlled modal response of a flexible beam.

Thau, F. E.↗
NASA NTRSDate not supplied

Recent System Identification Research at NASA Langley Research Center

This talk summarizes some of the recent advances in system identification at NASA Langley Research Center. Efforts discussed were applied to aeroelastic models, aircraft with redundant inputs and feedback control active, and aircraft flying in turbulence. Topics mentioned include experiment design with orthogonal multisine inputs, frequency response estimation, maximum likelihood parameter estimation, and parameter estimation considering process noise.

NASA LaRC↗
NASA NTRS2005

Identification of a typical flight patterns

Method and system for analyzing aircraft data, including multiple selected flight parameters for a selected phase of a selected flight, and for determining when the selected phase of the selected flight is atypical, when compared with corresponding data for the same phase for other similar flights. A flight signature is computed using continuous- valued and discrete-valued flight parameters for the selected flight parameters and is optionally compared with a statistical distribution of other observed flight signatures, yielding a typicality scores for the same phase for other similar flights. A cluster analysis is optionally applied to the flight signatures to define an optimal collection of clusters. A level of atypicality for a selected flight is estimated, based upon an index associated with the cluster analysis.

Irving C Statler↗
NASA NTRSDate not supplied

Updating High-Order Aeroservoelastic Models from Low-Order System Identification Results

Estimating aircraft models from test data requires several simplifying assumptions that introduce biases into the parameter estimates. In this paper, these biases are defined and a method for estimating the biases is discussed. Having an estimate of the bias allows the parameters estimated from test to be integrated into a high-order model. The Integrated Adaptive Wing Technology Maturation (IAWTM) wind tunnel model is discussed and the bias is demonstrated for one of the testing configurations. The methodology was able to estimate these biases and apply corrections to high-order aeroelastic models to improve the fit to test data. The consideration of the biases allows more meaningful comparisons and avoids the erroneous differences between pretest predictions and the fitted model.

Jeffrey Ouellette↗
NASA NTRSDate not supplied

Updating High-Order Aeroservoelastic Models from Low-Order System Identification Results

Estimating aircraft models from test data requires several simplifying assumptions that introduce biases into the parameter estimates. In this paper, these biases are defined and a method for estimating the biases is discussed. Having an estimate of the bias allows the parameters estimated from test to be integrated into a high-order model. The Integrated Adaptive Wing Technology Maturation (IAWTM) wind tunnel model is discussed and the bias is demonstrated for one of the testing configurations. The methodology was able to estimate these biases and apply corrections to high-order aeroelastic models to improve the fit to test data. The consideration of the biases allows more meaningful comparisons and avoids the erroneous differences between pretest predictions and the fitted model.

Jeffrey Ouellette↗
NASA NTRS1979

On adaptive modal control of large flexible spacecraft

A recently developed strategy for adaptive sampled-data control of distributed parameter systems based on a plant modal expansion description and modal simultaneous identification and regulation algorithms is presented with frequent reference to the annular momentum control device (AMCD) test example. The requirements of observation spillover reduction and modal eigenvector shape prespecification, which are especially crucial to the proposed adaptive control strategy, are addressed. Individual low pass time filtering of sensed AMCD particle displacements is proposed for observation spillover reduction. A layered scheme incorporating 'eigenvector' shape improvement is outlined to combat the expansion basis prespecification requirement.

Johnson, C. R., Jr.↗
NASA NTRS1989

Analysis and calibration of a three-invariant plasticity model for granular materials

This paper briefly reviews issues related to the characterization of properties of granular materials subjected to microgravity and one-gravity conditions at very low effective stress levels. The development of a three-invariant plasticity model that resembles the model devised by Lade (1979) is described. An inverse-identification scheme where the analysis tools are used to extract constitutive model parameters from experiments is also discussed.

Sture, S.↗
NASA NTRS2001

Health Monitoring Technology for Thermal Protection Systems on Reusable Hypersonic Vehicles

Integrated subsystem health diagnostics is an area where major improvements have been identified for potential implementation into the design of new reusable launch vehicles (RLVs) in order to reduce life cycle costs, to increase safety margins, and to improve mission reliability. This talk summarizes a joint effort between NASA Ames and industry partners to develop rapid non-contact diagnostic tools for health and performance monitoring of thermal protection systems (TPS) on future RLVs. The specific goals for TPS health monitoring are to increase the speed and reliability of TPS inspections for improved operability at lower cost. The technology being developed includes a 3-D laser scanner for examining the exterior surface of the TPS, and a subsurface microsensor suite for monitoring the health and performance of the TPS. The sensor suite consists of passive overlimit sensors and sensors for continuous parameter monitoring in flight. The sensors are integrated with radio-frequency identification (RFID) microchips to enable wireless communication of-the sensor data to an external reader that may be a hand-held scanner or a large portal. Prototypes of the laser system and both types of subsurface sensors have been developed. The laser scanner was tested on Shuttle Orbiter Columbia and was able to dimension surface chips and holes on a variety of TPS materials. The temperature-overlimit microsensor has a diameter under 0.05 inch (suitable for placement in gaps between ceramic TPS tiles) and can withstand 700 F for 15 minutes.

Milos, Frank S.↗