Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “NOSE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1979

Effects of fuselage forebody geometry on low-speed lateral-directional characteristics of twin-tail fighter model at high angles of attack

Low-speed, static wind-tunnel tests were conducted to explore the effects of fighter fuselage forebody geometry on lateral-directional characteristics at high angles of attack and to provide data for general design procedures. Effects of eight different forebody configurations and several add-on devices (e.g., nose strakes, boundary-layer trip wires, and nose booms) were investigated. Tests showed that forebody design features such as fineness ratio, cross-sectional shape, and add-on devices can have a significant influence on both lateral-directional and longitudinal aerodynamic stability. Several of the forebodies produced both lateral-directional symmetry and strong favorable changes in lateral-directional stability. However, the same results also indicated that such forebody designs can produce significant reductions in longitudinal stability near maximum lift and can significantly change the influence of other configuration variables. The addition of devices to highly tailored forebody designs also can significantly degrade the stability improvements provided by the clean forebody.

Carr, P. C.↗
NASA NTRS1979

Investigation of ground effects on large and small scale models of a three fan V/STOL aircraft configuration

Induced lift of a subsonic, three fan, lift/cruise, V/STOL aircraft configuration was investigated using scale modes of a multimission aircraft whose design incorporates a nose mounted lift fan and two lift/cruise units located over the wing. Configuration effects were assessed for lift improvement devices, lift/cruise nozzle rails, nozzle perimeter plates, and alternate nose fan exit hubs. Tests were conducted at four model heights (H/D = 0.95, 1.53, 3.06 and 6.45, where D is the average nozzle exit diameter equal to 0.997 m.) Results are presented and discussed.

Schuster, E. P.↗
NASA NTRS1980

Wind tunnel investigation of an all flush orifice air data system for a large subsonic aircraft

The results of a wind tunnel investigation on an all flush orifice air data system for use on a KC-135A aircraft are presented. The investigation was performed to determine the applicability of fixed all flush orifice air data systems that use only aircraft surfaces for orifices on the nose of the model (in a configuration similar to that of the shuttle entry air data system) provided the measurements required for the determination of stagnation pressure, angle of attack, and angle of sideslip. For the measurement of static pressure, additional flush orifices in positions on the sides of the fuselage corresponding to those in a standard pitot-static system were required. An acceptable but less accurate system, consisting of orifices only on the nose of the model, is defined and discussed.

Larson, T. J.↗
NASA NTRS1979

A simplified model for glass formation

A simplified model of glass formation based on the formal theory of transformation kinetics is presented, which describes the critical cooling rates implied by the occurrence of glassy or partly crystalline bodies. In addition, an approach based on the nose of the time-temperature-transformation (TTT) curve as an extremum in temperature and time has provided a relatively simple relation between the activation energy for viscous flow in the undercooled region and the temperature of the nose of the TTT curve. Using this relation together with the simplified model, it now seems possible to predict cooling rates using only the liquidus temperature, glass transition temperature, and heat of fusion.

Uhlmann, D. R.↗
NASA NTRS1980

Complete viscous flowfield solutions about a blunt parabolic body in a supersonic stream

A hybrid computational technique which splits the flowfield into inviscid and viscous regions is used to investigate the complete flowfield about axisymmetric parabolic blunt bodies in a supersonic stream. The solutions are carried out on the CDC CYBER-203 computer which, with its extensive memory, allows for the use of a large number of finite-difference mesh points, allowing resolution of important flowfield features. A range of freestream Mach number of 2-5 and a range of Re number based on nose radius of 500-125,000 was run for a sonic corner body. Contour plots of density, pressure, and Mach number, velocity vector plots, and surface distributions of pressure, heat transfer, and shear stress are presented. Also, correlations of the downstream extent of the base recirculation region with Re number based on nose radius are given.

Weilmuenster, K. J.↗
NASA NTRS1981

Wind-tunnel investigation of the tail-spoiler concept for stall-prevention on general aviation airplanes

The longitudinal aerodynamic characteristics of a full scale, single engine general aviation airplane equipped with an angle of attack limiting concept which used a tail mounted spoiler for stall prevention were investigated. The tail spoiler was deployed as a nonlinear function of changes in angle of attack in a narrow angle of attack range immediately preceding the stall angle. Spoiler deployment produced a nose down moment which limited the nose up trim capability of the elevator to an angle of attack below the stall angle of the airplane. The tail spoiler system produced significant increases in longitudinal stability and elevator hinge moments near the stall. The effects of power, flaps, and center of gravity position are also studied.

Satran, D. R.↗
NASA NTRS1981

Wind-tunnel investigation of the effects of blade tip geometry on the interaction of torsional loads and performance for an articulated helicopter rotor

The Langley transonic dynamics tunnel was used to determine the degree of correlation between rotor performance and the dynamic twist generated by changes in blade tip geometry using an articulated rotor with four different tip geometries at advance ratios of 0.20, 0.30 and 0.35. Based on the data obtained, it is concluded that: (1) there appears to be no strong correlation between blade torsion loads and rotor performance prediction; (2) for a given rotor task at each advance ratio investigated, both the azimuthal variation of torsional moment and the mean torsional moment at 81% radius are configuration dependent; (3) reducing the nose down twist on the advancing blade appears to be more important to forward flight performance than increasing the nose down twist on the retreating blade; (4) the rotor inflow model used was important in predicting the performance of the adaptive rotor; and (5) neither rigid blade solidity effects, inflow environment, nor blade torsion loads can be used alone to accurately predict active rotor performance.

Yeager, W. T.↗
NASA NTRS1982

Seeding considerations for an LV system in a large transonic wind tunnel

When it was decided to use a laser velocimeter to measure the properties of propellers, seeding was a great concern since large particles fail to flow and small ones are too small to be seen. Many methods were tried and weeded out by using a Malvern particle sizer. The most promising ones were tested in the tunnel and the laser velocimeter (LV) measurements compared to theoretical values of veocity as the particle approached a blunt nose body along a stagnation streamline. Data obtained from the LV system were compared with the one dimensional particle lag calculation. This figure showed the theoretical velocity over the blunt nose and a velocity profile for 5 um particles. This indicated the particles were approximately 5 um. The seeding method is shown. The seed was atomized by 2 seeders run with all 12 available atomizer jets on. The atomizer seed traveled from these two seeders through four 1 inch tubes 20 feet long to the plenum chamber where this cluster of tubes injected the seed into the air stream. The tubes were located 60 feet from the model and could be moved only by shutting the tunnel down. Future seeding plans are shown.

Freedman, R. J.↗
NASA NTRS1983

Pressures, forces, moments and shock shapes for a geometrically matched sphere-cone and hyperboloid at Mach 20.3 in helium

An investigation was conducted to compare measured and predicted pressure distributions, forces and moments, and shock shapes on a geometrically matched sphere-cone and hyperboloid. A hyperboloid with a nose radius of 0.5276 in. and an asymptotic angle of 39.9871 deg was matched to a sphere-cone with a nose radius of 0.750 in. and a cone half-angle of 45 deg. Experimental results in helium at a free-stream Mach number of 20.3 and a free-stream unit Reynolds number of 6.83 x 10 to the 6th power per foot were combined with predicted results from a theoretical method to compare the two shapes. Comparisons of experimental results showed small differences in the two shapes, but the prediction method provided better results for the hyperboloid than for the sphere-cone.

Calloway, R. L.↗
NASA NTRS1982

The receptivity of boundary layers on blunt bodies to oscillations in the free stream

It is concluded that in the region of the nose of a symmetric, two dimensional blunt body at zero angle of attack, the steady plus oscillating flow is very similar for a wide class of body shapes. This conclusion was shown to be true for elliptic cylinders with a/b 25, and for the parabolic cylinder. In all cases, the flow field in the nose region of a two dimensional blunt body is generic to that of the flow in the neighborhood of the stagnation point on a plane wall.

Grosch, C. E.↗
NASA NTRS1983

Flow fields and aerodynamic characteristics for hypersonic missiles with mid-fuselage inlets

A study was made to quantify forebody flow fields and to evaluate aerodynamic performance trends on a matrix of fuselage shapes for the mid-inlet/bolt-on-engine class of hypersonic airbreathing missiles for the Navy's vertical box launcher. The study indicated that inlet mass flow and pressure recovery can be increased by cambering the nose and increasing the width of the fuselage at both Mach 4 acceleration and Mach 6 cruise conditions. Aerodynamic trim predictions show that the drag at zero lift at Mach 4 decreases while the L/D max at Mach 6 increases with the nose camber, although these tendencies reverse with increasing width of maximum fuselage cross section.

Hunt, J. L.↗
NASA NTRS1983

Subsonic high-angle-of-attack aerodynamic characteristics of a cone and cylinder with triangular cross sections and a cone with a square cross section

Experiments were conducted in the 12-Foot Pressure Wind Tunnel at Ames Research Center on three models with noncircular cross sections: a cone having a square cross section with rounded corners and a cone and cylinder with triangular cross sections and rounded vertices. The cones were tested with both sharp and blunt noses. Surface pressures and force and moment measurements were obtained over an angle of attack range from 30 deg to 90 deg and selected oil-flow experiments were conducted to visualize surface flow patterns. Unit Reynolds numbers ranged from 0.8x1,000,000/m to 13.0x1,000,000/m at a Mach number of 0.25, except for a few low-Reynolds-number runs at a Mach number of 0.17. Pressure data, as well as force data and oil-flow photographs, reveal that the three dimensional flow structure at angles of attack up to 75 deg is very complex and is highly dependent on nose bluntness and Reynolds number. For angles of attack from 75 deg to 90 deg the sectional aerodynamic characteristics are similar to those of a two dimensional cylinder with the same cross section.

Clarkson, M. H.↗
NASA NTRS1984

Fine-cut bluntness effects on the hypersonic static stability of a 10 degree cone

A systematic wind-tunnel investigation has been performed on a series of spherically blunted 10-degree cones to determine Mach number and angle-of-attack effects on the hypersonic static stability. The cones, which range in nose-to-base radius ratios from 0 to 0.5, have been tested from -4 to 20 degrees angle of attack at Mach numbers of 6 and 10 in air and 20 in helium. Relatively large excursions in the center-of-pressure location were observed for small changes in cone nose bluntness. The movement of the center of pressure was also noted to become more pronounced as Mach number increased; increases in angle of attack tended to lessen the magnitude of these excursions. Computational predictions of basic aerodynamic coefficients as well as the center-of-pressure locations using both viscous and inviscid theory compare very well with the experimental data.

Bryan, M. D.↗
NASA NTRS1985

Impact studies of a 1/3-scale model of an air cushion vehicle

An experimental investigation was conducted to determine the effects of various parameters of the impact performance of a 1/3-scale dynamic model of an air cushion vehicle. Impact response was determined by measuring the maximum values of variables, including sidelobe, front lobe, and cavity pressures, normal acceleration, pitch and roll angles, and vertical displacement during impact, for various combinations of drop height, initial pitch and roll angles, and forward speed. Increasing initial pitch angle increased the maximum values of the front lobe pressure, normal acceleration, nose down pitch angle, and to some extent, vertical displacement, but it inversely affected the maximum cavity pressure. Increasing the drop height of the model increased the potential energy of the system and generally produced larger responses over the entire range of variables measured, except for the roll angle after impact, which remained constant. Forward speed had no effect on the impact performance of the model, except for essentially doubling the maximum nose down pitch angle after impact at the maximum speed tested.

Daugherty, R. H.↗
NASA NTRS1985

Direct Transient Analysis of a Fuze Assembly by Axisymmetric Solid Elements

A fuze assembly, which consists of three major parts, nose, collar and sleeve, was designed to survive severe transverse impact giving a maximum base acceleration of 20.000 G. It is shown that hoop failure occurred in the collar after the impact. They also showed that by bonding the collar to the nose, the collar was able to survive the same impact. To find out the effectiveness of the bonding quantitatively, axisymmetric solid elements TRAPAX and TRIAAX were used in modelling the fuze and direct transient analysis was performed. The dynamic stresses in selected elements on the bonded and unbonded collars were compared. The peak hoop stresses in the unbonded collar were found to be up to three times higher than those in the bonded collar. The NASTRAN results explained the observed hoop failure in the unbonded collar. In addition, static and eigenvalue runs were performed as checks on the models prior to the transient runs. The use of the MPCAX cards and the existence and contributors of the calculated first several nearly identical natural frequencies are addressed.

Dai, C. C.↗
NASA NTRS1984

Numerical computation of space shuttle orbiter flow field

The complete inviscid viscous real gas flow around the Space Shuttle Orbiter was computed. Real gas effects are important in predicting the reentry environment around the Orbiter because the high temperatures within the shock layer cause the air to dissociate and ionize, thus invalidating the perfect gas assumption. It is shown that real gas effects has a significant influence on the Orbiter aerodynamics. The approach utilizes a time dependent Navier-Stokes code to compute the subsonic nose portion of the flow field. This nose solution provides the initial conditions for the parabolized Navier-Stokes (PNS) code.

Tannehill, J. C.↗
NASA NTRS1984

A flying superconducting magnet and cryostat for magnetic suspension of wind-tunnel models

The engineering practicality of a persistent high-field superconducting solenoid cryostat as a magnetic suspension and balance system (MSBS) for wind-tunnel testing of aircraft and missile models is examined. The test apparatus is a simple solenoid of filamentary NbTi superconductor with a cupronickel matrix. The apparatus, with a length-to-diameter ratio of 6 to 1 and a radius of 32 mm, used a 0.25 mm wire with a critical current of 27 A in an external field of 6 T. The total heat inleak of 150 mW was achieved. Helium boiloff rates were tested over a range of operating conditions, including pitch attitudes from 10 deg nose down to 90 deg nose up; the rate was estimated as low, but the aerodynamic acceptability of venting gaseous helium has not been determined. It is shown that the effectiveness of the concept increases with increasing scale, and performance in excess of that of conventional ferromagnets is achievable with reduction in size and costs, and with aptness to transonic wind-tunnel testing. Detailed specifications and schematics are included.

Britcher, C.↗
NASA NTRS1984

Investigation of the external flow analysis for density measurements at high altitude

The results of analysis performed on the external flow around the shuttle orbiter nose regions at the Shuttle Upper Atmosphere Mass Spectrometer (SUMS) inlet orifice are presented. The purpose of the analysis is to quantitatively characterize the flow conditions to facilitate SUMS flight data reduction and subsequent determination of orbiter aerodynamic force coefficients in the hypersonic rarefied flow regime. Experimental determination of aerodynamic force coefficients requires accurate simultaneous measurement of forces (or acceleration) and dynamic pressure along with independent knowledge of density and velocity. The SUMS provides independent measurement of dynamic pressure; however, it does so indirectly and requires knowledge of the relationship between measured orifice conditions and the dynamic pressure which can only be determined on the basis of molecule or theory for a winged configuration. Monte Carlo direct simulation computer codes were developed for both the flow field solution at the orifice and for the internal orifice flow. These codes were used to study issues associated with geometric modeling of the orbiter nose geometry and the modeling of intermolecular collisions including rotational energy exchange and a preliminary analysis of vibrational excitation and dissociation effects. Data obtained from preliminary simulation runs are presented.

Bienkowski, G. K.↗