Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Modules”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

Influence of the Bulk Resistivity on Silicon Heterojunction Solar Cells and Module Reliability

Recent developments in industry on surface passivation open the possibility of using less doped substrates in silicon solar cells. In this report we investigate how the bulk resistivity affects the performance of silicon cells and the reliability of modules. Herein, n- and p-type silicon heterojunction cells with bulk resistivities between 3 and 15 000 Ωcm are studied. We measure the current–voltage characteristics of n-type cells across the resistivity range, and we find comparable responses to illumination intensities between 0.1 and 1 suns. The cells with bulk resistivities over 1000 Ωcm show breakdown voltages larger than -1000 V, almost two orders of magnitude higher than in typical commercial cells. Although modules have bypass-diodes to prevent cells from going into breakdown, higher breakdown voltages can improve the reliability of modules in case of bypass-diode failure and reduce the module cost by easing the number of bypass-diodes required. Finally, the cells have been submitted to light soaking. The float-zone p-type cells with bulk resistivities over 10 000 Ωcm are less sensitive to light-induced degradation than cells with bulk resistivities below 10 Ωcm. The former show to recover few hours after light soaking, while the latter recover only after dark annealing.

14 SOLAR ENERGY↗
DOE OSTI2025

Earth-scattering induced modulation in low-threshold dark matter experiments

Dark matter particles with sufficiently large interactions with ordinary matter can scatter in the Earth before reaching and scattering in a detector. This induces a modulation in the signal rate with a period of one sidereal day. We calculate this modulation for sub-GeV dark matter particles that interact either with a heavy or an ultralight dark-photon mediator and investigate the resulting signal in low-threshold detectors consisting of silicon, xenon, or argon targets. The scattering in the Earth is dominated by dark matter scatters off nuclei, while the signal in the detector is easiest to observe from dark matter scattering off electrons. We investigate the properties of the modulation signal and provide projections of the sensitivity of future experiments. We find that a search for a modulation signal can probe new regions of parameter space near the energy thresholds of current experiments, where the data are typically dominated by backgrounds.

Models for Dark Matter↗
DOE OSTI2025

New electric force and charge exchange modules in discrete element model enables particle dynamics simulation in electric field

Discrete element modeling (DEM) is an important technique for particle dynamics simulation. The field of metal additive manufacturing often utilizes DEM to simulate the rheological behaviors of powder. Standard contact and short-range interactions are sufficient in most cases but insufficient to describe the particle dynamics with the influence of an electric field. Modeling such a system requires additional physics to describe the particle–field interactions. The relevant physics has been experimentally understood but is not yet available in DEM. Here, we develop a charge exchange and an electric force module. The electric force module governs particle response to the electric field, while the charge exchange module enables particles to acquire proper charge during contact with charged geometries. We validate the modules against analytical calculations and high-speed videos of electrostatic powder deposition experiments. Notably, the model struggles to capture the initial particle levitation. We later deploy a modified electric field, as supported by static electric field simulation, to better approximate the electric field penetration into the powder layer. This modification improves the model’s capability of simulating realistic particle levitation. The results highlight the challenges of modeling particle behaviors in the electric field while demonstrating the feasibility of obtaining quantitative results, which are difficult to measure experimentally.

charge exchange↗
DOE OSTI2024

Dual-module humidity pump for efficient air dehumidification: Demonstration and performance limitations

Condensation dehumidification in conventional air conditioning technologies is energy-intensive, accounting for up to 50% of building cooling energy used in some climates. Selective vacuum membrane dehumidification (VMD) is one of the leading alternative dehumidification technologies due to its potential for significant energy savings, and the “dual-module humidity pump” is one of the most promising VMD concepts. Here, this work is the first to provide experimental proof-of-concept for the dual-module humidity pump system and provides the first thermodynamic modeling framework that accounts for realistic steady-state operating limitations, both of which are lacking in the current literature. Additionally, this work is the first to provide a system design solution that overcomes practical challenges associated with air accumulation in the vacuum channels. The experimental results in this work show that the current prototype can remove up to 45% of the water vapor in the air stream, and the vapor pressure difference in the vapor rejection module needs to be approximately 2–4 times greater than that of the dehumidification module in order to maintain balanced mass transfer. The thermodynamic model applied to typical air conditioning conditions shows that the ideal dehumidification (latent) COPs can reach up to 40, but practical COPs are limited to approximately 10. Furthermore, the model shows that the overall energy efficiency increases as the membrane air selectivity increases, though this improvement gradually starts to diminish when the membrane selectivity is increased above 10,000.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2020

Coupled methane and NO x conversion on Pt + Pd/Al 2 O 3 monolith: Conversion enhancement through feed modulation and Mn 0.5 Fe 2.5 O 4 spinel addition

The performance of a dual-layer Pt-Pd/Al 2 O 3 washcoated monolith promoted by an Al 2 O 3 -supported Mn 0.5 Fe 2.5 O 4 spinel base layer was evaluated with the objective to develop a catalyst with a lower loading of Platinum group metal (PGM) for stoichiometric natural gas vehicle (NGV) emission control. Flow reactor results show that a combination of a lean/rich modulated feed and spinel addition gives enhanced methane and NO conversions compared to a steady-state feed having the same overall composition. Washcoated catalysts – PGM-only, spinel-only, PGM + spinel – were compared over a wide range of operating conditions. The results show a decrease in the methane conversion light-off temperature of up to 85 °C for an application-relevant feed (CH 4 + NO + H 2 + CO + O 2 + H 2 O + CO 2 ) while a moderate 40 °C decrease was observed for a simple feed (CH 4 + O 2 + H 2 O + CO 2 ). In the absence of spinel the modulation enhancement is negatively impacted at high methane conversion (> 80 %). The data show that the O 2 storage and release property of the spinel is needed to fully exploit the modulation enhancement. The mechanism responsible for the enhancement is linked to suppression of O 2 inhibition on the methane oxidation rate near the stoichiometric neutral point (λ = 1). Sufficiently fast cycling achieves a balance between a metallic and oxidic precious metal crystallites favorable for methane activation. The addition of spinel moves this balance closer to the λ = 1 feed, enabling a high oxidation efficiency with lower byproduct NH 3 selectivity. Enhancement in the NO conversion follows the methane conversion due to an easier NO reduction under the slightly rich of stoichiometric feed. Comparison of the PGM + spinel catalysts to PGM-only catalysts shows that the addition of spinel in combination with modulation can achieve the same activity with a lower PGM loading.

03 NATURAL GAS↗
DOE OSTI2021

Metal leaching from Lithium-ion and Nickel-metal hydride batteries and photovoltaic modules in simulated landfill leachates and municipal solid waste materials

Photovoltaic (PV) modules and batteries can either be recycled or disposed of in landfills at end-of-life (EoL). This work focuses on disposal since the benefit of recycling PV modules and batteries is well established. This study characterizes the potential toxicity due to metals leaching from selected PV modules and batteries through both the Toxicity Characteristic Leaching Procedure (TCLP) and in-house batch leaching protocols to probe the impact on metallic ion mobility as a function of the different types of e-waste entering the waste stream, the magnitude of device damage when placed into the waste stream, and the simulated municipal solid waste (SMSW) composition. Our results showed that one PV module and three battery types in this study should be classified as hazardous waste within the U.S. However, for some of the other e-wastes, metals of concern including Cr, Cu, Hg, Ni, Pb, and Zn leached during the batch tests but not in the TCLP regulatory method. For most of the waste types, the amounts of metals that leached in the TCLP test and batch tests were much lower than the total extractable amounts, demonstrating the potential for additional unaccounted for amounts of metals to leach. Our results demonstrate that the TCLP regulatory method might fail at predicting potential leaching and at capturing the complexity of e-waste leaching in landfill conditions. It confirms that additional work is needed urgently to develop appropriate EoL procedures for MSW with PV and battery e-waste.

42 ENGINEERING↗
DOE OSTI2024

Integration and validation of some modules for modelling of high-speed chemically reactive flows in two-phase gas-droplet mixtures

Three modules are integrated into the built-in OpenFOAM rhoCentralFoam solver towards accurate and efficient modelling of high-speed chemically reactive flows in two-phase gas-droplet mixtures within the OpenFOAM 10.0 framework. The first module is the mixture-averaged diffusion model. The second module is the built-in OpenFOAM Lagrangian solver coupled with optimised droplet drag coefficient and convective heat transfer coefficient sub-models. The last module is a sparse stiff chemistry solver based on dynamic adaptive hybrid integration (AHI-S). The optimised droplet sub-models are first verified in correct implementation for subsequent simulations in this work. Further, they show good accuracy against experimental and analytical data in the modelling of ammonia droplet acceleration and cooling in the flowing and/or low-temperature air. The accuracy and efficiency gains related to the mixture-averaged diffusion model and the AHI-S chemistry solver are examined by simulating 1-D detonation propagation in ammonia droplet-free/laden ammoniaoxygen mixtures. Numerical results of detonation propagation speed, gaseous temperature, density, and species distributions around the induction zone show good agreement with experimental data and analytical solutions. Compared to the built-in OpenFOAM diffusion model, the mixture-averaged diffusion model provides different numerical predictions of pulsating instabilities in detonation propagation. It shows better accuracy in depicting the detonation structure within the droplet-free section attributed to improved multi-component diffusion modelling. Compared to the built-in OpenFOAM solver EulerImplicit (backward Euler), the AHI-S chemistry solver reduces the computational cost by around 50%. It achieves satisfactory accuracy in calculating detonation propagation speed within the droplet-free section with the optimal efficiency when the safety factor, β, equals 0.5.

42 ENGINEERING↗
DOE OSTI2026

Flow dynamics and heat transfer in simplified battery energy storage systems with heated battery modules

Large-scale energy storage systems (ESSs) composed of batteries show promise in addressing current energy challenges, but dissipation of generated heat is important. Here, this paper focuses on buoyant convective flows in simplified ESS battery racks. Natural convection is not generally the primary cooling strategy but can be important in abnormal scenarios where there is module overheat or potentially thermal runaway. We use computational fluid dynamics to investigate the flow dynamics and heat transfer mechanisms in a simplified parameterized rack design. Despite its simplicity, this configuration produces many of the relevant features expected in real ESSs without details of module geometry or hardware, allowing broad conclusions independent of manufacture-specific designs. We start by providing visualizations of the flowfield and measurements of entrainment, heat flux, and pressure. To characterize the dependence on the system parameters, we develop an integral-scale analysis of the average temperature equation to highlight the dominant source terms. We use results from this analysis to derive a steady network model composed of simple algebraic expressions to provide first-order predictions of entrainment through the rack. The network model leads to a linear scaling of the Reynolds number based on convective mass flux with respect to the Grashof number based on the heat source. We deduce empirical relationships that relate the heat exchanged between modules using a surface-averaged Nusselt number as a function of the local Reynolds and Rayleigh numbers. Lastly, we investigate how space between the modules and rack in the spanwise direction creates flow bypass, resulting in different flow pathways.

Battery thermal management↗
DOE OSTI2021

In-situ thermal transport measurement of flowing fluid using modulated photothermal radiometry

In situ thermal transport measurement of flowing fluid could be useful for the characterization and diagnosis of practical thermal systems such as fluid heat exchangers and thermal energy storage systems. Despite abundant reports on the ex-situ thermal conductivity measurement of stagnant fluids, a suitable technique for the thermal conductivity measurement of flowing fluid has been rarely reported. Here, this paper presents the thermal conductivity measurement of flowing fluid within a pipe using a non-contact modulated photothermal radiometry (MPR) technique, where the surface of the pipe is heated by an intensity-modulated laser and the heat diffuses into the fluid with suitable modulation frequency. We design a tube section with small wall thickness suitable for the MPR measurements to maximize the sensitivity of the thermal response to the fluid properties while minimizing the lateral heat spreading effect. Intrinsic thermal conductivity of different fluids was obtained within a proper range of frequency and flow velocity where the forced convection effect is negligible. The forced convection effect became prominent at high flowing velocity and at low modulation frequency, leading to higher effective thermal conductivity of the fluid. It is found that the intrinsic thermal conductivity could be obtained when the flow velocity is less than 100 mm/sec and Re D 1/2 Pr 1/3 < 100 for DI water and Xceltherm oil under the specified experimental conditions, where Re D is the Reynolds number and Pr is the Prandtl number.

42 ENGINEERING↗
DOE OSTI2024

Nanometric modulations of the magnetic structure of the element Nd

The rare earth neodymium arguably exhibits the most complex magnetic ordering and series of magnetic phase transitions of the elements. Here we report the results of small-angle neutron scattering (SANS) measurements as a function of temperature and applied magnetic field to study magnetic correlations on nanometer length scales in Nd. We support these results with additional neutron diffraction, thermodynamic and synchrotron x-ray measurements. The SANS measurements reveal the presence of modulation vectors characterizing the ordered spin configuration which exhibit changes in magnitude and direction that are phase dependent. Between 5.9 and 7.6 K an additional modulation vector is observed with magnitude Q = 0.12 Å -1 . This scattering appears to originate from order of the Nd layers which contain a center of inversion. Tracking this modulation vector as a function of magnetic field indicates a phase boundary at ≈1 T. The modulation vectors observed in this study establish the presence of nanometer length scale spin textures which are likely stabilized by frustrated Ruderman–Kittel–Kasuya–Yosida (RKKY) interactions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Strip sensor performance in prototype modules built for ATLAS ITk

ATLAS experiment is preparing an upgrade of its detector for High-Luminosity LHC (HL-LHC) operation. The upgrade involves installation of the new all-silicon Inner Tracker (ITk). In the context of the ITk preparations, more than 80 strip modules were built with prototype barrel sensors. They were tested with electrical readout on a per-channel basis. In general, an excellent performance was observed, consistent with previous ASIC-level and sensor-level tests. However, the lessons learned included two phenomena important for the future phases of the project. First was the need to store and test the modules in a dry environment due to humidity sensitivity of the sensors. The second was an observation of high noise regions for 2 modules. The high noise regions were tested further in several ways, including monitoring the performance as a function of time and bias voltage. Additionally, direct sensor-level tests were performed on the affected channels. The inter-strip resistance and bias resistance tests showed low values, indicating a temporary loss of the inter-strip isolation. A subsequent recovery of the noise performance was observed. Here we present the test details, an analysis of how the inter-strip isolation affects the module noise, and the relationship with sensor-level quality control tests.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

The MOOSE electromagnetics module

The Multiphysics Object-Oriented Simulation Environment (MOOSE) electromagnetics module has been developed to increase MOOSE physics module capabilities, enabling standalone and coupled computational electromagnetics within the MOOSE multiphysics ecosystem. The module is actively being utilized in the areas of plasma physics and advanced manufacturing, and it currently provides initial demonstrated capability in multi-dimensional, complex-valued electromagnetic wave propagation, electrostatic contact, reflection and transmission, and electromagnetic eigenvalue problems. Two-dimensional wave propagation and one-dimensional wave reflection and transmission are showcased as examples in this work. The modularity, parallelism, and plug-in infrastructure for custom future development is inherited from MOOSE itself, and the module can be used with both MOOSE-based and external codes, giving great flexibility.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Cell dark current–voltage from non-calibrated module electroluminescence image analysis

Here, we present a fast, accurate, and reliable method of obtaining cell dark current–voltage (I–V) curves from module electroluminescence (EL) images without requiring calibration or correction. For a pristine module, EL-derived dark I–V are compared to directly probed data for a variety of changing imaging parameters: camera sensor, lens, filter, aperture width, exposure time (level of sensor saturation), number of images used, and various combinations of these. Pristine modules and those experiencing different modes and degrees of degradation are examined. A recent study of modules using five different cell technologies demonstrates the practicality of our “EL sweep” technique for performance and degradation studies.

14 SOLAR ENERGY↗
DOE OSTI2022

Technoeconomic Analysis of High-Value, Crystalline Silicon Photovoltaic Module Recycling Processes

Recycling is an important circular economy strategy, and for photovoltaics (PV), the one that has received the greatest research attention. Recycling of PV modules is required in Europe; everywhere else it competes in the market of end-of-life options, where cost is a primary decision factor. The vast majority of PV modules sold globally are crystalline-silicon (c-Si); most of the rest of the market are cadmium telluride thin film modules whose primary manufacturer runs its own commercial-scale recycling program. While many different c-Si recycling approaches and technologies have been proposed, they generally lack accompanying cost estimates or enough process information to model costs. Herein we develop detailed estimates of seven categories of capital and operating costs along with estimates of revenue from recovered materials for each step in two proposed recycling processes for c-Si PV modules. Using these results, we develop a hypothetical third recycling process merging process steps from the original two, estimate surcharges required to achieve minimum sustainable prices for each recycling process, as well as consider how economies of scale could reduce costs. Increasing the purity of and identifying higher-value markets for recovered materials are approaches to reducing costs and increasing recycling rates in voluntary markets.

crystalline silicon↗
DOE OSTI2022

Dependence of adhesion on degradation mechanisms of ethylene co-vinyl acetate encapsulants over the lifetime of photovoltaic modules

The long-term reliability of encapsulation has a critical impact on the overall cost and effectiveness of photovoltaic modules. An often overlooked but important element of this reliability concerns adhesive degradation of the encapsulant, which results in delamination. This work critically examines the degradation mechanisms – deacetylation, β-scission, and hydrolytic depolymerization – primarily responsible for adhesion loss in ethylene co-vinyl acetate (EVA) encapsulants to provide evidence and clarity regarding the contribution of these mechanisms to the adhesive degradation over the lifetime of a module. EVA samples obtained from mini-modules exposed in two sets of controlled, accelerated conditions – with and without ultraviolet (UV) radiation – are characterized to find specific evidence for the proposed degradation mechanisms. The mini-modules were exposed up to 10,000 h, which represents up to 15–20 years in the field. Results affirm that initially, deacetylation dominates the degradation before scission takes over, followed by hydrolytic depolymerization. Additional analysis highlights the climacteric interdependency between deacetylation and hydrolytic depolymerization as it relates to eventual delamination, where deacetylation products catalyze interfacial hydrolysis reactions. Furthermore, effects occurring at a given interface are isolated, explicitly providing evidence for how these mechanisms are nonuniform throughout the thickness of the EVA. Results demonstrate that the EVA that interfaces with the glass as opposed to the cell experiences increased levels of degradation, explaining why this initially stronger interface becomes the preferential interface for delamination after longer periods of exposure. Additionally, elevated temperatures alone are shown to induce limited migration of sodium ions across the glass/EVA interface.

36 MATERIALS SCIENCE↗
DOE OSTI2025

On reduced modelling of the modulational dynamics in magnetohydrodynamics

This paper explores structure formation in two-dimensional magnetohydrodynamic (MHD) turbulence as a modulational instability (MI) of turbulent fluctuations. We focus on the early stages of structure formation and consider simple backgrounds that allow for a tractable model of the MI while retaining the full chain of modulational harmonics. This approach allows us to systematically examine the validity of popular closures such as the quasilinear approximation and other low-order truncations. We find that, although such simple closures can provide quantitatively accurate approximations of the MI growth rates in some regimes, they can fail to capture the modulational dynamics in adjacent regimes even qualitatively, falsely predicting MI when the system is actually stable. We find that this discrepancy is due to the excitation of propagating spectral waves (PSWs) which can ballistically transport energy along the modulational spectrum, unimpeded until dissipative scales, thereby breaking the feedback loops that would otherwise sustain MIs. The PSWs can be self-maintained as global modes with real frequencies and drain energy from the primary structure at a constant rate until the primary structure is depleted. To describe these waves within a reduced model, we propose an approximate spectral closure that captures them and MIs on the same footing. We also find that introducing corrections to ideal MHD, conservative or dissipative, can suppress PSWs and reinstate the accuracy of the quasilinear approximation. In this sense, ideal MHD is a ‘singular’ system that is particularly sensitive to the accuracy of the closure within mean-field models.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Conformal High-Power-Density Half-Heusler Thermoelectric Modules: A Pathway toward Practical Power Generators

Thermoelectric generators (TEGs) exploiting the Seebeck effect provide a promising solution for waste heat recovery. Among the large number of thermoelectric (TE) materials, half-Heusler (hH) alloys are leading candidates for medium- to high-temperature power generation applications. However, the fundamental challenge in this field has been inhomogeneous material properties at large wafer diameters, insufficient power output from the modules, and rigid form factors of TE modules. This has restricted the transition of TEGs in practical applications for over three decades. Here, we successfully demonstrate large diameter wafers with uniform TE properties, high-power conformal hH TE modules for high-temperature application, and their direct integration on flue gas platforms, such as cylindrical tubes, to form large area flexible TEGs. This new conformal architecture design provides a breakthrough toward medium-/high-temperature TEGs over the conventional BiTe- and polymer-based flexible TEG design. In this work, a variable fill factor and greater flexibility due to the conformal design result in higher device performance as compared to conventional rigid TEG devices. Modules with 72-couple hH legs exhibit a device high-power-density of 3.13 W cm-2 and a total output power of 56.6 W under a temperature difference of 570 degrees C. These results provide a promising pathway toward widespread utilization of thermoelectric technology into the waste heat recovery application and will have a significant impact on the development of practical thermal to electrical converters.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2026

Small Molecule Inhibitor-Modulated Al 2 O 3 Atomic Layer Deposition on Monolayer MoS 2 for Controlled Nucleation

The integration of ultrathin dielectrics on two-dimensional (2D) semiconductors is essential for advancing beyond-Si electronics. However, the intrinsic inertness of van der Waals 2D basal planes remains a primary bottleneck to achieving uniform dielectric nucleation and growth. Here, in this study, we introduce a small molecule inhibitor (SMI)-modulated thermal atomic layer deposition (ALD) strategy, exemplified by aluminum oxide (Al 2 O 3 ) ALD on monolayer molybdenum disulfide (1L MoS 2 ) with acetic acid (HAc) SMI. The ABC-type sequence comprises HAc inhibitor (A), trimethylaluminum (TMA) precursor (B), and deionized H 2 O coreactant (C). In situ quartz crystal microbalance (QCM) studies reveal robust HAc adsorption on Al 2 O 3 and suppression of subsequent oxide growth on HAc-passivated surfaces. When applied to 1L MoS 2 , this inhibitory pathway enables HAc to selectively passivate nascent Al 2 O 3 nuclei formed on the MoS 2 surface, limiting their three-dimensional (3D) island coarsening and redirecting precursor adsorption toward the uncovered basal plane. Consequently, nearly continuous ultrathin (∼1.5 nm) Al 2 O 3 films are achieved on 1L MoS 2 with markedly improved uniformity compared to standard Al 2 O 3 ALD using TMA and H 2 O, as validated by atomic force microscopy (AFM), cross-sectional scanning transmission electron microscopy (STEM), and energy-dispersive X-ray spectroscopy (EDS). Density functional theory (DFT) calculations further provide atomistic insight into HAc-modulated Al 2 O 3 nucleation, corroborating the energetic preference of HAc for Al 2 O 3 over MoS 2 and attenuated TMA adsorption on HAc-passivated surfaces. Spatially resolved Raman spectroscopy also confirms that the HAc-modulated process preserves the structural integrity of 1L MoS 2 , with only minimal strain and doping perturbations observed after dielectric deposition. This SMI-modulated approach offers a broadly applicable framework for controlling ALD nucleation across various inhibitors, ALD chemistries, and 2D materials, opening opportunities for reliable dielectric integration in next-generation nanoelectronics.

36 MATERIALS SCIENCE↗