Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “MARTENSITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

The microstructure and mechanical behaviors of the Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy produced by laser melting deposition

The microstructure and mechanical properties of the Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy produced by laser melting deposition have been investigated. The columnar grains of the Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy due to the layer-by-layer epitaxial growth from the underlying template grains during laser melting deposition, which is roughly parallel to the deposition direction, had been found by optical microscopy; strong [101{sup ¯}2]{sub α} crystallographic texture has been confirmed by X-ray diffraction and electron backscattered diffraction. Depending on the last heating history, the microstructure of the alloy undergoes a continued change opposite to the deposition direction: martensitic α′ (transformed β); coarsened primary α laths with transformed β; coarsened primary α laths; and the fine basketweave microstructure with a few coarsened α laths or annealed martensitic α′. The average Vickers micro-hardness value of the alloy is 364 HV. The alloy parallel to the deposition direction presents lower tensile strength (925 MPa) and better elongation (18.8%), compared with 1025 MPa and 8.2% of that vertical to the deposition direction, which has been discussed using its microstructure characterization. - Highlights: • The columnar grains and strong [101{sup ¯}2]{sub α} crystallographic texture of the Ti–6.5Al–3.5Mo–1.5Zr–0.3Si alloy due to the epitaxial growth from the underlying template grains • The microstructure evolution of the alloy depends on the last heating history. • The specimen parallel to the deposition direction presents lower ultimate tensile strength and higher elongation than the specimen vertical to the deposition direction.

36 MATERIALS SCIENCE↗

Microstructure characterization of heat affected zone after welding in Mod.9Cr–1Mo steel

The microstructure of the heat affected zone after welding was investigated in Mod.9Cr–1Mo steel, using TEM and STEM-EDX. The microstructure of thin foil was observed at the fusion line, and at the positions of 0.5 mm, 1.0 mm, 1.5 mm, 2.0 mm, 2.5 mm, 3.0 mm and 3.5 mm to the base metal side of the fusion line. Martensite structure with very fine lath and high dislocation density was confirmed at all positions. Twins with a twin plane of (112) were locally observed at all positions. Elemental mapping was obtained for all positions by means of STEM-EDX. Inclusions of mainly Si were formed at the fusion line but not at the other positions. No precipitates could be detected at the fusion line or at the position of 0.5 mm. On the other hand, MX particles were observed at the positions of 1.0 mm, 1.5 mm, 2.0 mm, 2.5 mm, 3.0 mm and 3.5 mm even after welding. M{sub 23}C{sub 6} particles were also confirmed at the positions of 2.0 mm, 2.5 mm, 3.0 mm and 3.5 mm. Very fine equiaxed grains were locally observed at the positions of 2.0 mm and 2.5 mm. The Cr content of the equiaxed grains was about 12 mass%, although the martensite area included about 8 mass% Cr. - Graphical abstract: Display Omitted - Highlights: • Nonequilibrium microstructure of heat affected zone was observed after welding in Mod.9Cr–1Mo steel. • Inclusions containing Si were detected at the fusion line. • Undissolved M{sub 23}C{sub 6} and MX particles were confirmed in heat affected zone. • Twins with a twin plane of (112) were locally observed at all positions. • Very fine ferrite grains with high Cr content were observed in fine grained heat affected zone.

36 MATERIALS SCIENCE↗

Effect of starting microstructure upon the nucleation sites and distribution of graphite particles during a graphitising anneal of an experimental medium-carbon machining steel

The potential for using graphite particles as an internal lubricant during machining is considered. Graphite particles were found to form during graphitisation of experimental medium-carbon steel alloyed with Si and Al. The graphite nucleation sites were strongly influenced by the starting microstructure, whether ferrite–pearlite, bainite or martensite, as revealed by light and electron microscopy. Favourable nucleation sites in the ferrite–pearlite starting microstructure were, not unexpectedly, found to be located within pearlite colonies, no doubt due to the presence of abundant cementite as a source of carbon. In consequence, the final distribution of graphite nodules in ferrite–pearlite microstructures was less uniform than for the bainite microstructure studied. In the case of martensite, this study found a predominance of nucleation at grain boundaries, again leading to less uniform graphite dispersions. - Highlights: • Metallography of formation of graphite particles in experimental carbon steel. • Potential for using graphite in steel as an internal lubricant during machining. • Microstructure features expected to influence improved machinability studied. • Influence of pre-anneal starting microstructure on graphite nucleation sites. • Influence of pre-anneal starting microstructure on graphite distribution. • Potential benefit is new free-cutting steel compositions without e.g. Pb alloying.

36 MATERIALS SCIENCE↗

Correlation between mechanical properties and retained austenite characteristics in a low-carbon medium manganese alloyed steel plate

The effects of retained austenite characteristics on tensile properties and low-temperature impact toughness have been investigated by means of transmission electron microscopy and X-ray diffraction. It was found that only part of austenite phase formed during heat treating was left at room temperature. Moreover, the film-like retained austenite is displayed between bcc-martensite laths after heat treating at 600 °C, while the block-form retained austenite with thin hcp-martensite laths is observed after heat treating at 650 °C. It has been demonstrated that the film-like retained austenite possesses relatively high thermal and mechanical stability, and it can greatly improve low-temperature impact toughness, but its contribution to strain hardening capacity is limited. However, the block-form retained austenite can greatly enhance ultimate tensile strength and strain hardening capacity, but its contribution to low-temperature impact toughness is poor. - Highlights: • Correlation between retained austenite and impact toughness was elucidated. • The impact toughness is related to mechanical stability of retained austenite. • The effect of retained austenite on tensile and impact properties is inconsistent.

36 MATERIALS SCIENCE↗

Structural characteristics of transition-iron-carbide precipitates formed during the first stage of tempering in 4340 steel

Microstructural and crystallographic characteristics of fine-scale transition-iron-carbide precipitates formed in martensite during tempering of 4340 steel at 200 °C for 3.6 ks were studied via transmission electron microscopy. Precipitates of near-equiaxed shapes and about 10 nm in size were observed, and rows of closely spaced precipitates were aligned predominantly along < 100 > martensite directions. Aggregates of aligned precipitates were up to 150 nm in length, although occasional kinks were present that disrupted the alignment, and some of the adjacent precipitates possessed somewhat different crystallographic orientations. Electron-diffraction results were analyzed in detail and found to be consistent with both epsilon-carbide and eta-carbide phases. Similarities between these two phases were highlighted and discussed. Experimental electron-diffraction data were compared with data from five different unit cells, and each was found to be consistent within uncertainty ranges of ± 0.003 nm for interplanar spacings, ± 2° for angles between plane normals, and a few degrees for the orientation relationship between precipitates and the matrix.

36 MATERIALS SCIENCE↗

The correlation of local deformation and stress-assisted local phase transformations in MMC foams

Cellular structures are of growing interest for industry, and are of particular importance for lightweight applications. In this paper, a special case of metal matrix composite foams (MMCs) is investigated. The investigated foams are composed of austenitic steel exhibiting transformation induced plasticity (TRIP) and magnesia partially stabilized zirconia (Mg-PSZ). Both components exhibit martensitic phase transformation during deformation, thus generating the potential for improved mechanical properties such as strength, ductility, and energy absorption capability. The aim of these investigations was to show that stress-assisted phase transformations within the ceramic reinforcement correspond to strong local deformation, and to determine whether they can trigger martensitic phase transformations in the steel matrix. To this end, in situ interrupted compression experiments were performed in an X-ray computed tomography device (XCT). By using a recently developed registration algorithm, local deformation could be calculated and regions of interest could be defined. Corresponding cross sections were prepared and used to analyze the local phase composition by electron backscatter diffraction (EBSD). The results show a strong correlation between local deformation and phase transformation. - Graphical abstract: Display Omitted - Highlights: • In situ compressive deformation on MMC foams was performed in an XCT. • Local deformation fields and their gradient amplitudes were estimated. • Cross sections were manufactured containing defined regions of interest. • Local EBSD phase analysis was performed. • Local deformation and local phase transformation are correlated.

36 MATERIALS SCIENCE↗

Microstructural characterization of hydrogen induced cracking in TRIP-assisted steel by EBSD

The present work evaluates hydrogen induced cracking by performing an elaborate EBSD (Electron BackScatter Diffraction) study in a steel with transformation induced plasticity (TRIP-assisted steel). This type of steel exhibits a multiphase microstructure which undergoes a deformation induced phase transformation. Additionally, each microstructural constituent displays a different behavior in the presence of hydrogen. The aim of this study is to obtain a better understanding on the mechanisms governing hydrogen induced crack initiation and propagation in the hydrogen saturated multiphase structure. Tensile tests on notched samples combined with in-situ electrochemical hydrogen charging were conducted. The tests were interrupted at stresses just after reaching the tensile strength, i.e. before macroscopic failure of the material. This allowed to study hydrogen induced crack initiation and propagation by SEM (Scanning Electron Microscopy) and EBSD. A correlation was found between the presence of martensite, which is known to be very susceptible to hydrogen embrittlement, and the initiation of hydrogen induced cracks. Initiation seems to occur mostly by martensite decohesion. High strain regions surrounding the hydrogen induced crack tips indicate that further crack propagation may have occurred by the HELP (hydrogen-enhanced localized plasticity) mechanism. Small hydrogen induced cracks located nearby the notch are typically S-shaped and crack propagation was dominantly transgranularly. The second stage of crack propagation consists of stepwise cracking by coalescence of small hydrogen induced cracks. - Highlights: • Hydrogen induced cracking in TRIP-assisted steel is evaluated by EBSD. • Tensile tests were conducted on notched hydrogen saturated samples. • Crack initiation occurs by a H-Enhanced Interface DEcohesion (HEIDE) mechanism. • Crack propagation involves growth and coalescence of small cracks. • Propagation is governed by the characteristics of phases on the crack path.

36 MATERIALS SCIENCE↗

Mechanisms of ultrafine-grained austenite formation under different isochronal conditions in a cold-rolled metastable stainless steel

The primary objective of this work is to obtain fundamental insights on phase transformations, with focus on the reaustenitization process (α′→γ transformation), of a cold-rolled (CR) semi-austenitic metastable stainless steel upon different isochronal conditions (0.1, 1, 10 and 100 °C/s). For this purpose, an exhaustive microstructural characterization has been performed by using complementary experimental such as scanning and transmission electron microscopy (SEM and TEM), electron backscattered diffraction (EBSD), electron probe microanalysis (EPMA), micro-hardness Vickers and magnetization measurements. It has been detected that all microstructural changes shift to higher temperatures as the heating rate increases. The reaustenitization occurs in two-steps for all heating rates, which is attributed to the chemical banding present in the CR state. The α′→γ transformation is controlled by the migration of substitutional alloying elements across the austenite/martensite (γ/α′) interface, which finally leads to ultrafine-grained reaustenitized microstructures (440–280 nm). The morphology of the martensite phase in the CR state has been found to be the responsible for such a grain refinement, along with the presence of χ-phase and nanometric Ni{sub 3}(Ti,Al) precipitates that pin the austenite grain growth, especially upon slowly heating at 0.1 °C/s. - Highlights: •Ultrafine-grained austenite structures are obtained isochronally at 0.1–100 °C/s •The α′→γ transformation occurs in two steps due to the initial chemical banding •A diffusional mechanism governs the α′→γ transformation for all heating rates •The dislocation-cell-type of martensite promotes a diffusional mechanism •Precipitates located at α′/γ interfaces hinder the austenite growth.

36 MATERIALS SCIENCE↗

Characterization of as-welded microstructure of heat-affected zone in modified 9Cr–1Mo–V–Nb steel weldment

Non-equilibrium microstructure of the heat-affected zone (HAZ) in the as-welded modified 9Cr–1Mo–V–Nb pipe steel (P91) weldment deposited by gas tungsten arc welding (GTAW) and flux core arc welding (FCAW) has been characterized by field-emission scanning electron microscope (FESEM) and electron backscatter diffraction (EBSD). The heterogeneous structures in the sub-layers of the as-welded HAZ are attributable to phase transformations caused by the welding thermal cycles and the local structure variations in the as-received base metal. Coarse-grained heat-affected zone (CGHAZ) has a prior austenite grain (PAG) size of 20 μm. Fine uniformly-distributed precipitates and a higher fraction of MX carbonitrides are observed in the CGHAZ. Fine-grained heat-affected zone (FGHAZ) consists of the finest grains (1.22 μm measured by EBSD, 5 μm PAG size), coarse undissolved M{sub 23}C{sub 6} carbides within the PAG boundaries and fine nucleated M{sub 23}C{sub 6} particles within the martensite laths. Inter-critical heat-affected zone (ICHAZ) consists of partially austenitized grains and over-tempered martensite laths. EBSD kernel average misorientation (KAM) map in the FGHAZ close to the ICHAZ illustrates the greatest local strain variations with a moderate normalized KAM value of 0.92°. The majority (88.1%) of the matrix grains in the CGHAZ are classified as deformed grains by EBSD grain average misorientation (GAM) evaluation. The FGHAZ close to the ICHAZ has the most recrystallized grains with an area fraction of 14.4%. The highest density variation of precipitates within grains in the FGHAZ originates from the inhomogeneous chemistry in the base metal. - Highlights: •A comprehensive characterization of the as-welded HAZ of P91 weldment is conducted. •Structural features in the each layer of the HAZ are quantified by EBSD. •Structural heterogenities in HAZ are due to welding cycle and base metal structure. •FGHAZ contains the finest grain structure and largest precipitate density variation.

36 MATERIALS SCIENCE↗

Fabrication and characterization of microstructure of stainless steel matrix composites containing up to 25 vol% NbC

AISI 440 stainless steels reinforced with various volume fractions of niobium carbide (NbC) particles of up to 25 vol% were fabricated in-situ using an argon arc furnace and then heat-treated to produce a martensitic matrix. Optical and scanning electron microscopy (SEM), energy dispersive X-ray spectroscopy (EDS) and electron back-scatter diffraction (EBSD) techniques were used to analyze the microstructure, phases and composition of these composites. Interestingly, it was found that Chinese-script NbC could nucleate on existing primary NbC particles creating NbC clusters with complex microstructures. Additionally, hardness tests were used to evaluate viability in mining and mineral processing applications. The increase in NbC content resulted in an overall increase in the hardness of the composites while causing a marginal decrease in the amount of Cr in solid solution with the matrix, which could be a concern for corrosion resistance. The latter was due to the fact that the NbC lattice could dissolve a minor amount of Cr. Thermodynamic simulations also attributed this to a slight increase in M{sub 7}C{sub 3} precipitation. Nonetheless, these novel composites show great promise for applications in wear and corrosive environments. - Highlights: •Stainless steels reinforced with NbC particles of up to 25 vol% were fabricated. •NbC was formed in-situ in the steels using an arc melter. •Martensitic transformation of the matrix of each sample was achieved. •NbC reinforcements increased the bulk hardness values of the steels. •Dissolved Cr in the matrix of each sample was sufficient for passivity in theory.

36 MATERIALS SCIENCE↗

Microstructure and mechanical properties of resistance-spot-welded joints for A5052 aluminum alloy and DP 600 steel

The microstructure and mechanical properties of resistance-spot-welded A5052 aluminum alloy and DP 600 dual-phase steel joint were studied. The fusion zone (FZ) and heat-affected zone (HAZ) of DP 600 exhibited lath martensite and ferrite-martensite structures, respectively. The microstructure of FZ and HAZ in the A5052 side was composed of cellular crystals and the boundary region of FZ exhibited a columnar crystal morphology. A Fe{sub 2}Al{sub 5} intermetallic compound (IMC) layer with 3.3 μm thickness was found adjacent to the DP 600 side, whereas a needle-shaped Fe{sub 4}Al{sub 13} IMC layer with length of 0.67 μm to 15.8 μm was found adjacent to the aluminum alloy side. The maximum tensile shear load of the A5052/DP 600 joint was 5.5 KN, with a corresponding molten nugget diameter of 6.3 mm. The fracture morphology of the optimized A5052/DP 600 joint was mainly an elongated dimple fracture accompanied by cleavage fracture. - Highlights: •A5052 and DP 600 with large gaps in properties were investigated by RSW. •The microstructures of RSW joints in DP 600/A5052 were examined detailedly. •The micro/macro-characteristics and strength relations of joints were analyzed.

36 MATERIALS SCIENCE↗

Microstructure and partitioning behavior characteristics in low carbon steels treated by hot-rolling direct quenching and dynamical partitioning processes

In this work, a new process and composition design are proposed for “quenching and partitioning” or Q&P treatment. Three low carbon steels were treated by hot-rolling direct quenching and dynamical partitioning processes (DQ&P). The effects of proeutectoid ferrite and carbon concentration on microstructure evolution and mechanical properties were investigated. The present work obtained DQ&P prototype steels with good mechanical properties and established a new notion on compositions for Q&P processing. Microstructures were characterized by means of electro probe microanalyzer (EPMA), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD), transmission electron microscopy (TEM) and X-ray diffraction (XRD), especially the morphology and size of retained austenite. Mechanical properties were measured by uniaxial tensile tests. The results indicated that introducing proeutectoid ferrite can increase the volume fraction of retained austenite and thus improve mechanical properties. TEM observation showed that retained austenite included the film-like inter-lath austenite and blocky austenite located in martensite/ferrite interfaces or surrounded by ferrites. It was interesting that when the carbon concentration is as low as ~ 0.078%, the film-like inter-lath untransformed austenite cannot be stabilized to room temperature and almost all of them transformed into twin martensite. The blocky retained austenite strengthened the interfaces and transformed into twin martensite during the tensile deformation process. The PSEs of specimens all exceeded 20 GPa.%. - Highlights: •This study focused on a new process: Q&P process applying dynamical partitioning. •Ferrite can increase the volume fraction of retained austenite. •The film-like austenite and the blocky austenite were observed. •The low carbon steels treated by new process reached PSEs higher than 20 GPa.%.

36 MATERIALS SCIENCE↗

Effect of heat input on dissimilar welds of ultra high strength steel and duplex stainless steel: Microstructural and compositional analysis

The effect of heat input on the microstructure and compositional heterogeneity of welds of direct-quenched ultra high strength steel (Optim 960 QC) and duplex stainless steel (UNS S32205) was studied. The dissimilar welds were made using GMAW with a fully austenitic filler wire. In addition to grain coarsening in the heat affected zone (HAZ) of the ferritic side, it was found that an increase in heat input correlatively increased the proportional volume of bainitic to martensitic phases. Coarse ferritic grains were observed in the duplex HAZ. Higher heat input, however, had a beneficial effect on the nucleation of austenite in the HAZ. Heat input had a regulatory effect on grain growth within the austenitic weld and more favorable equiaxed austenite was obtained with higher heat input. On the ferritic side of the welds, macrosegregation in the form of a martensitic intermediate zone was observed for all the cooling rates studied. However, on the duplex side, macrosegregation in the fusion boundary was only noticed with higher cooling rates. Microstructural observations and compositional analysis suggest that higher heat input could be beneficial for the structural integrity of the weld despite higher heat input increasing the extent of adverse coarse grains in the HAZ, especially on the ferritic side. - Highlights: •The effect of heat input on dissimilar welds of UHSS and DSS was studied. •Transmutation of the microstructure was discussed in detail. •The influence of heat input on compositional heterogeneity of welds was described. •Higher heat input enhanced bainitic transformation on the ferritic side. •Macrosegregation was affected by the amount of heat input on the DSS side.

36 MATERIALS SCIENCE↗

Dislocation density evolution in the process of high-temperature treatment and creep of EK-181 steel

X-ray diffraction has been used to study the dislocation structure in ferrite-martensite high-chromium steel EK-181 in the states after heat treatment and high-temperature creep. The influence of heat treatment and stress on evolution of lath martensite structure was investigated by and electron back-scattered diffraction. The effect of nitrogen content on the total dislocation density, fraction of edge and screw dislocation segments are analyzed. - Highlights: •Fraction of edge dislocation in quenched state depends on nitrogen concentration. •Nitrogen affects the character of dislocation structure evolution during annealing. •Edge dislocations fraction influences on dislocation density after aging and creep.

36 MATERIALS SCIENCE↗

Hydrogen induced mechanical degradation in tungsten alloyed steels

Highlights: • The effect of H charging on tungsten alloyed steels is assessed by tensile tests. • The HE resistance increased for the Q&T condition compared to the as-Q state. • H trapping and absorption are determined by H characterization methods. • H diffusivity was higher in Q&T condition due to dislocation density decrease. • A correlation between the degree of HE and the amount of mobile H was established. - Abstract: The present work considers the effect of hydrogen on the mechanical properties of generic Fe-C-W alloys. Thermal treatment aimed at a martensitic microstructure and two conditions are compared; i.e. an as-quenched state and a quenched and tempered state with lower dislocation density and with W based carbides formed during tempering. The hydrogen induced mechanical degradation is evaluated by in-situ tensile tests, while thermal desorption spectroscopy, hot/melt extraction and permeation experiments are performed to understand the observed hydrogen embrittlement degree. The hydrogen induced ductility loss increases with increasing carbon content due to the higher amount of hydrogen trapped by the denser martensitic lath boundaries. Furthermore, the quenched and tempered condition shows a lower susceptibility to hydrogen. This is correlated to the reduced hydrogen content when tempered due to a decreased dislocation density and the fact that the tempered induced W{sub 2}C particles did not trap hydrogen. Moreover, corresponding observations to this interpretation are perceived by permeation experiments since, on the one hand, the diffusion coefficient decreases with carbon content due to the increasing trapping ability of alloy A → B → C, and, on the other hand, the diffusivity increases when tempering is applied, which is also linked to the decrease in dislocation density and the disability of the carbides to hinder hydrogen diffusion by efficient trapping.

36 MATERIALS SCIENCE↗

Effects of proton irradiation on the microstructure and shape recovery characteristics of a NiTi alloy

Highlights: • The complex multilayer structure can be induced by irradiation. • Phase constitution with increased fluence evolved as follows: B19’ → (B19’ + B2 + Ti{sub 2}Ni) → (B2 + Ti{sub 2}Ni + TiH{sub 2}). • The transformation temperature decreases remarkablly with the increasing of irradiation fluence. • The strain recovery characteristics deteriorated significantly with the irradiation fluence increasing. - Abstract: Herein, we investigate the effects of proton irradiation on the structure and shape recovery characteristics of a NiTi alloy and provide a mechanistic explanation of the observed phenomena. Detailed analysis revealed that bombardment with 3 MeV protons induced the formation of a complex multilayer structure comprising TiH{sub 2}, Ti{sub 2}Ni, austenite and austenite-martensite layers along the irradiation direction with increasing distance and the origin of the above structure was shown to be closely related to the preferential sputtering effect and irradiation-induced segregation. Finally, the shape recovery characteristics significantly deteriorated with increasing irradiation fluence, since the multilayer structure hindered the martensitic transformation.

36 MATERIALS SCIENCE↗

Phase transformations in body-centered cubic NbxHfZrTi high-entropy alloys

Highlights: • BCC phase stability and phase transformations of NbxHfZrTi HEAs were investigated. • Three types of phase transformations: β → ω, β → α″ and β → α′ in HEAs were observed. • The athermal ω phase in Nb{sub 0.2}HfZrTi HEA leads to a much higher yield strength. • The reversible β → α″ in Nb{sub 0.4}HfZrTi HEA results in a narrow cyclic hysteresis loop. • A sluggish effect of martensitic transformations in complex HEAs is revealed. - Abstract: The stability of body-centered cubic (β) phases and phase transformations of NbxHfZrTi (x = 1, 0.6, 0.4 and 0.2) high-entropy alloys (HEAs) were investigated. Three types of transformations were observed: the β → ω transformation during cooling in Nb0.2 HEA, the deformation-induced β → α″ and β → α′ transformations in Nb0.4 and Nb0.2 HEAs, respectively. This implies that the phonon anomalies, T{sub 1}1/2(110) and L2/3(111), as the origins of phase transformations in simple Ti, Zr and Hf alloys, also exist in composition-complex TiZrHf-based HEAs. However, the very small fraction of deformation-induced α′/α″ martensite in fractured Nb0.4 and Nb0.2 suggests a sluggish effect of transformation as compared with simple β-Ti alloys.

36 MATERIALS SCIENCE↗

Austenite and precipitation in secondary-hardening ultra-high-strength stainless steel

Highlights: • Austenite and precipitation in Ferrium S53 steel were analyzed. • Austenite decreased to less than 5% after cryogenic treatment and tempering. • M{sub 2}C carbide could segregate inside martensite lath or in the larger parallel microstructure. - Abstract: Ferrium S53 is a new secondary-hardening ultra-high-strength stainless steel, with more Cr than other Co-Ni ultra-high-strength steels. Austenite has a great effect on the fracture toughness of this metal, and the carbides that are precipitated are the main strengthening phase of Ferrium S53 steel; in this study, its microstructural changes during heat treatment were observed and analyzed by X-ray diffraction (XRD), Optical microscope (OM), SEM, and transmission electron microscopy (TEM). About 40.85% retained austenite in the quenched sample is decreased to less than 5% after cryogenic treatment and tempering. In the final sample, block austenite is retained austenite, and film austenite around 5 nm in width is reverted austenite. Inside the martensite lath, parallel twin-like structures are actually segregated M{sub 2}C precipitates, and most of them are smaller than 20 nm. These precipitates can be aggregated into a several-micron-long parallel zonal microstructure.

36 MATERIALS SCIENCE↗