Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “LIGNITE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Chemically authentic surrogate mixture model for the thermophysical properties of a coal-derived liquid fuel

We developed a surrogate mixture model to represent the physical properties of a coal-derived liquid fuel using only information obtained from a gas chromatography-mass spectrometry analysis of the fuel and a recently developed 'advanced distillation curve'. We then predicted the density, speed of sound, and viscosity of the fuel and compared them to limited experimental data. The surrogate contains five components (n-propylcyclohexane, trans-decalin, {alpha}-methyldecalin, bicyclohexane, and n-hexadecane), yet comparisons to limited experimental data demonstrate that the model is able to represent the density, sound speed, and viscosity to within 1, 4, and 5%, respectively. 102 refs., 2 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

CO{sub 2} looping cycle performance of a high-purity limestone after thermal activation/doping

The influence of thermal pretreatment on the performance of a high-purity limestone (La Blanca) during CO{sub 2} capture cycles is investigated in this paper. This limestone was chosen for more detailed investigation because, in earlier research, it failed to show any favorable effect as a result of thermal pretreatment. Here, the original sample, with a particle size of 0.4-0.6 mm, and ground samples were thermally pretreated at 1000-1200{sup o}C, for 6-24 h, and then subjected to several carbonation/calcination cycles in a thermogravimetric analyzer (TGA). This work shows that thermal pretreatment failed to produce a significant self-reactivation effect during CO{sub 2} cycles, despite the use of a wide range of conditions during pretreatment (grinding, temperature, and pretreatment duration) as well as during cycling (CO{sub 2} concentration and duration of the carbonation stage). Additional doping experiments showed that both high Na content and lack of Al in La Blanca limestone cause poor self-reactivation performance after thermal pretreatment. Scanning electron microscope-energy-dispersive X-ray (SEM-EDX) analyses also confirmed more pronounced sintering and loss of activity, which we believe are caused by the relatively high Na content. However, stabilization of sorbent particle morphology by Al can allow this limestone to show self-reactivation performance and higher conversions over a longer series of CO{sub 2} cycles. 35 refs., 12 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Characterization of molecular mass ranges of two coal tar distillate fractions (creosote and anthracene oils) and aromatic standards by LD-MS, GC-MS, probe-MS and size-exclusion chromatography

Laser-desorption mass spectrometry (LD-MS) method development was undertaken to improve estimates of mass ranges for complex hydrocarbon mixtures. A creosote oil, an anthracene oil, and a mixture of known polynuclear aromatic hydrocarbon (PAH) compounds were examined. The formation of cluster ions was possible without overloading the detector system. These multimer ions overlapped with higher-mass ion signals from the sample. However, careful balancing of sample concentration, laser power, total ion current, and delayed ion extraction appears to show high-mass materials without generating high-mass multimer (artifact) ions. It is possible to suppress the formation of cluster ions by keeping low target concentrations and, consequently, low gas phase concentrations formed by the laser pulse. The principal method used in this work was the fractionation of samples by planar chromatography followed by successive LD-MS analysis of the separated fractions directly from the chromatographic plates. This method separated the more abundant small molecules from the less abundant large molecules to permit the generation of their mass spectra independently, as well as reducing the concentration of sample by spreading over the PC-plate. The technique demonstrably suppressed multimer formation and greatly improved the reproducibility of the spectra. Results showed the presence of molecule ions in the ranges m/z 1000-2000 for the anthracene oil sample and m/z 600-1500 for the creosote oil sample, tailing off to m/z about 5,000. The creosote oil contained significantly less of this high-mass material than the anthracene oil sample, and in both cases, high-mass material was only present in low quantities. The method outlined in the paper appears directly applicable to the characterization of heavier coal and petroleum derived fractions. 44 refs., 14 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Application of a diode-laser-based ultraviolet absorption sensor for in situ measurements of atomic mercury in coal-combustion exhaust

A diode-laser-based ultraviolet absorption sensor was successfully demonstrated for both in situ and extractive sampling atomic mercury measurements in a laboratory-scale 29.3 kWt (100 000 BTU/h) coal combustor and in situ measurements in a flow reactor at Texas A&M University. Laser sensor measurements were compared to measurements from a commercial mercury analyzer (CMA). A 375 nm single-mode laser and a 784 nm distributed feedback (DFB) laser are sum-frequency-mixed in a nonlinear {beta}-barium borate crystal to generate a 254 nm beam. By tuning the frequency of the DFB laser, the ultraviolet beam frequency was tuned across the transition frequency of mercury at 253.7 nm. The tuning range was large enough that an off-resonant baseline was clearly visible on both sides of the Hg transition. No pretreatment is required for elemental mercury measurements, and the effects of broadband absorption can be effectively eliminated during data analysis. Extractive sampling was demonstrated to improve the detection limit of the sensor and demonstrate the feasibility of total mercury concentration measurements in the future through extractive sampling. Significant variation in the atomic mercury concentration of coal-combustion exhaust was observed over short time periods during our in situ measurements. The sensor detection limits for in situ and extractive sampling are 0.3 and 0.1 parts per billion over a 1 m path length, respectively. 34 refs., 11 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Comparison of different natural sorbents for removing CO{sub 2} from combustion gases, as studied in a bench-scale fluidized bed

The reaction of CO{sub 2} with porous particles of CaO for chicken eggshells, mussel shells, and limestone. The reaction is a promising way of removing CO{sub 2}, e.g., from the exhaust of a power station, so that a pure stream of CO{sub 2} can subsequently be produced for sequestration by calcining (roasting) the solid CaCO{sub 3}. The reverse of the reaction regenerates the sorbent, which can thus be used cyclically. The reaction were investigated using a small electrically heated bed of sand at about 750{degree}C, fluidized by N{sub 2}. Typically, a sample (about 2 g) of cleaned calcareous material (sieved to about 600 {mu}m) was added to the hot bed, and the CO{sub 2} produced was measured, while the material was fully calcined. Next, enough CO{sub 2} was added to the fluidizing N{sub 2} to raise (CO{sub 2}) to above the value for equilibrium; thus, the CaO was carbonated. This forward step is shown to exhibit an apparent final conversion, the carrying capacity of the sorbent, below unity. This carrying capacity reduces after several cycles of calcination and carbonation, because blockage of pores denies access of CO{sub 2} to part of the CaO. After several such cycles, particles were removed from the reactor, either in their partially carbonated or fully calcined states, for studies using gas adsorption analysis, X-ray diffraction, and mercury porosimetry. Interestingly, it was found for all three sorbents that the carrying capacity of CaO for CO{sub 2} degraded at a similar rate. The carrying capacity was roughly proportional to the volume of pores narrower than about 100 nm, as measured by Barrett-Joyner-Halenda (BJH) gas adsorption analysis. Evidently, these narrow pores contain both the surface area for CO{sub 2} to absorb and the empty volume to accommodate the product, CaCO{sub 3}. The resistance of eggshells to attrition was broadly comparable to that of Purbeck (U.K.) limestone. 24 refs., 8 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

Influence of nitric acid treatment in different media on X-ray structural parameters of coal

The treatment of coal with nitric acid in aqueous and non-aqueous media introduces changes in the chemical and spatial structure of the organic mass. Four coals of different rank have been treated with nitric acid in aqueous and glacial acetic acid media for assessing the changes in the structural parameters by the X-ray diffraction (XRD) technique. Slow-scan XRD has been performed for the raw and treated coals, and X-ray structural parameters (d002, Lc, and Nc) and aromaticity (fa) have been determined by profile-fitting software. Considerable variation of the structural parameters has been observed with respect to the raw coals. The d002 values have decreased in aqueous medium but increased in acetic acid medium; however, Lc, Nc, and fa values have increased in aqueous medium but decreased in acetic acid medium. It is also observed that considerable oxidation takes place during nitric acid treatment in aqueous medium, but nitration is the predominant phenomenon in acetic acid medium. Disordering of the coal structure increases in acetic acid medium, but a reverse trend is observed in the aqueous medium. As a result, structurally modified coals (SMCs) are derived as new coal-derived substances. 15 refs., 6 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Combustion characteristics of fine- and micro-pulverized coal in the mixture of O{sub 2}/CO{sub 2}

The effects of oxygen concentration, particle size, and heating rate on the coal combustion characteristics under an O{sub 2}/CO{sub 2} atmosphere were investigated. The results indicated that the oxygen concentration played the most important role. As the oxygen concentration increases, the ignition and burnout temperatures decrease and the comprehensive combustion property index S increases. Moreover, the improvement of the oxygen concentration intensified the effects of the other factors. The ignition mechanism changes from hetero-homogeneous type to homogeneous type as the oxygen concentration increases. The ignition and burnout temperatures decrease slightly as the mean particle size decreases, and the index S increases measurably as the mean particle size decreases. The heating rate has different effects on the ignition temperature, burnout temperature, and index S at different oxygen concentrations. 19 refs., 9 figs., 2 tabs.

01 COAL, LIGNITE, AND PEAT↗

High-level computer molecular modeling for low-rank coal containing metal complexes and iron-catalyzed steam gasification

Low-rank coal is a complex mixture; consequently, it is necessary to develop simpler molecular representations for computational modeling. Our modeling objective has been to develop molecules suitable for semi-empirical (SE) computations of low-rank coal containing transition-metal complexes. These molecular models contain oxygen functional groups that are macro-ligands, forming coordination complexes with specific three-dimensional (3D) orientations; consequently, we develop models that encapsulate the properties of low-rank coals and can form metal complexes. The large computer resources required for SE calculations of these molecules limited their size; of the models examined, those containing numerous short links between phenyl groups caused excessive strain and were unsuitable to model transition-metal complexes. Computations (SE) of our models provided data on (i) hydrogen bonds of coal containing water, (ii) formation of aqua-inorganic species and transition-metal complexes, (iii) pyrolysis chemistry involving transformations of metal hydroxide/oxides, (iv) routes for H{sub 2} and CO formation, and (v) mechanism of iron-catalyzed steam gasification. Our char models, on the basis of transformations of the coal model, were consistent with low-temperature pyrolysis; these were disordered structures with some phenyl groups spaced between 0.35 and 0.4 nm. Smaller models of char and chars containing transition-metal clusters were optimized with SE and density functional theory (DFT) computations; these models were useful in modeling the mechanism of catalytic steam gasification. Our modeling of the mechanisms of iron-catalyzed steam gasification was consistent with experimental data. 44 refs., 5 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

Experiment and computational fluid dynamics (CFD) simulation of urea-based selective noncatalytic reduction (SNCR) in a pilot-scale flow reactor

A turbulent reacting flow computational fluid dynamics (CFD) model involving a droplet size distribution function in the discrete droplet phase is first built for selective noncatalytic reduction (SNCR) processes using urea solution as a NOx removal reagent. The model is validated with the experimental data obtained from a pilot-scale urea-based SNCR reactor installed with a 150 kW gas burner. New kinetic parameters of seven chemical reactions for the urea-based NOx reduction are identified and incorporated into the three-dimensional turbulent flow CFD model. The two-phase droplet model with the non-uniform droplet size is also combined with the CFD model to predict the trajectory of the droplets and to examine the mixing between the flue gas and reagents. The maximum NO reduction efficiency of about 80%, experimentally measured at the reactor outlet, is obtained at 940{degree}C and a normalized stoichiometric ratio (NSR) = 2.0 under the conditions of 11% excess air and low CO concentration (10-15 ppm). At the reaction temperature of 940{degree}C, the difference of a maximum of 10% between experiments and simulations of the NO reduction percentage is observed for NSR = 1.0, 1.5, and 2.0. The ammonia slip is overestimated in CFD simulation at low temperatures, especially lower than 900{degree}C. However, the CFD simulation results above 900{degree}C show a reasonable agreement with the experimental data of NOx reduction and ammonia slip as a function of the NSR. 31 refs., 3 figs., 6 tabs.

01 COAL, LIGNITE, AND PEAT↗

Investigating the formation mechanism of soot-like materials present in blast furnace coke samples

An attempt to gain an understanding of the formation mechanism of these 'soot-like' materials has been made by means of tracing the changes in the molecular-mass distribution and molecular structure of the NMP-extractable materials from an injectant coal as well as its partially gasified chars and its pyrolytic tars. Variations in the SEC chromatograms provide clues about changes in the apparent molecular-mass distributions of these NMP extracts. Results suggest that the build-up of 'soot-like' materials follows from the secondary reactions of tars evolved from the injectant coal. The likely secondary-reaction pathways have been probed by collating structural information on these NMP extracts. The time-resolved 13-16 and 22-25 min elution fractions from the SEC column have been characterized using UV fluorescence (UV F) spectroscopy. Greater concentrations of larger aromatic ring systems are found present in samples formed under conditions appearing more prone for soot formation. The 11-16 min (large apparent molecular mass) effluent from SEC has been examined by Fourier transform infrared (FTIR) spectroscopy and transmission electron microscopy (TEM). Results from FTIR spectroscopy are consistent with the UV F data, showing more significant extents of dehydrogenation under conditions more prone to form soot. Similarly, TEM results show that larger amount of graphene layers exist in samples exposed to more soot-prone conditions. The emerging picture for the formation of 'soot-like' materials involves a well-defined sequence. Tars evolved from the injectant coal undergo secondary dehydrogenation, condensation, and repolymerization reactions, which eventually lead to the formation of the NMP-extractable 'soot-like' materials of large apparent molecular mass. 44 refs., 7 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Experiment and modeling of CO{sub 2} capture from flue gases at high temperature in a fluidized bed reactor with Ca-based sorbents

The cyclic CO{sub 2} capture and CaCO{sub 3} regeneration characteristics in a small fluidized bed reactor were experimentally investigated with limestone and dolomite sorbents. Kinetic rate constants for carbonation and calcination were determined using thermogravimetric analysis (TGA) data. Mathematical models developed to model the Ca-based sorbent multiple cycles of CO{sub 2} capture and calcination in the bubbling fluidized bed reactor agreed with the experimental data. The experimental and simulated results showed that the CO{sub 2} in flue gases could be absorbed efficiently by limestone and dolomite. The time for high-efficiency CO{sub 2} capture decreased with an increasing number of cycles because of the loss of sorbent activity, and the final CO{sub 2} capture efficiency remained nearly constant as the sorbent reached its final residual capture capacity. In a continuous carbonation and calcination system, corresponding to the sorbent activity loss, the carbonation kinetic rates of sorbent undergoing various cycles are different, and the carbonation kinetic rates of sorbent circulating N times in the carbonation/calcination cycles are also different because of the different residence time of sorbent in the carbonator. Therefore, the average carbonation rate was given based on the mass balance and exit age distribution for sorbent in the carbonator. The CO{sub 2} capture characteristics in a continuous carbonation/calcination system were predicted, taking into consideration the mass balance, sorbent circulation rate, sorbent activity loss, and average carbonation kinetic rate, to give useful information for the reactor design and operation of multiple carbonation/calcination reaction cycles. 27 refs., 15 figs., 1 tab.

01 COAL, LIGNITE, AND PEAT↗

Mesophase from anthracene oil-based pitches

This work deals with the preparation of the mesophase from two pitch-like materials obtained from anthracene oil by oxidative thermal condensation (AOP-1) and the subsequent thermal treatment and distillation of AOP-1 (AOP-2). The mesophase was obtained by the controlled pyrolysis (440-470{degree}C and different periods of residence times) and subsequent sedimentation of the samples. In the case of the pitch prepared by oxidative thermal condensation, a dynamic pressure of 5 bar was applied during the pyrolysis. The pressure was a critical parameter, and its influence was also investigated. The results show that AOP-1 requires higher temperatures and/or residence times to develop mesophase than AOP-2. After sedimentation, a sample consisting of mainly mesophase was produced in all of the cases. The characterization of the mesophases by means of techniques, such as elemental and thermogravimetric analysis and optical microscopy, showed that anthracene oil-based derivatives are appropriate precursors for producing QI-free mesophase with suitable properties for the fabrication of a wide range of carbon materials. 26 refs., 5 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Post-treatment of fly ash by ozone in a fixed bed reactor

The residual carbon in fly ash produced from pulverized coal combustion can adsorb the air-entraining admixtures (AEAs) added to enhance air entrainment in concrete. This behavior of the ash can be suppressed by exposing the fly ash to oxidizing species, which oxidizes the carbon surface and thus prevents the AEA to be adsorbed. In the present work, two fly ashes have been ozonated in a fixed bed reactor and the results showed that ozonation is a potential post-treatment method that can lower the AEA requirements of a fly ash up to 6 times. The kinetics of the carbon oxidation by ozone was found to be fast. A kinetic model has been formulated, describing the passivation of carbon, and it includes the stoichiometry of the ozone consumption (0.8 mol of O{sub 3}/kg of C) and an ineffective ozone loss caused by catalytic decomposition. The simulated results correlated well with the experimental data. 28 refs., 7 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Iron Aerogel and Xerogel Catalysts for Fischer-Tropsch Synthesis of Diesel Fuel

Iron aerogels, potassium-doped iron aerogels, and potassium-doped iron xerogels have been synthesized and characterized and their catalytic activity in the Fischer-Tropsch (F-T) reaction has been studied. Iron aerogels and xerogels were synthesized by polycondensation of an ethanolic solution of iron(III) chloride hexahydrate with propylene oxide which acts as a proton scavenger for the initiation of hydrolysis and polycondensation. Potassium was incorporated in the iron aerogel and iron xerogel by adding aqueous K{sub 2}CO{sub 3} to the ethanolic solutions of the Fe(III) precursor prior to addition of propylene oxide. Fischer-Tropsch activities of the catalysts were tested in a fixed bed reactor at a pressure of 100 psi with a H{sub 2}:CO ratio of 2:1. Iron aerogels were found to be active for F-T synthesis, and their F-T activities increased on addition of a K containing promoter. Moessbauer spectroscopic data are consistent with an open, nonrigid iron(III) aerogel structure progressing to an iron carbide/metallic iron catalyst via agglomeration as the F-T synthesis proceeds in the course of a 35 h fixed bed reaction test.

01 COAL, LIGNITE, AND PEAT↗

Characterization and pyrolysis behavior of novel anthracene oil derivatives

The characterization and pyrolysis behavior of a set of pitches prepared from anthracene oil have been described. The pitches were obtained from four successive cycles of a sequential process that begins with blowing air through the heated anthracene oil, to bring about recombination reactions. Reaction products are distilled to give a pitch residue and a lighter fraction. Thermal treatment/distillation cycles of this reaction product yield a pitch and a distillate fraction (unreacted anthracene oil) during each subsequent stage. Products obtained during the process have been characterized by elemental analysis, Fourier transform infrared (FTIR) and ultraviolet (UV)-fluorescence spectroscopy, and size-exclusion chromatography (SEC). The pyrolytic behavior of the anthracene oil derivatives was examined using a thermogravimetric balance. Thermal treatment of the anthracene oil and its (distilled) reaction products at 440-460{degree}C under 5 bar pressure leads to a partially anisotropic pitch with the formation of a liquid crystal phase (mesophase). The formation and evolution of these mesophases were analyzed by optical microscopy. 25 refs., 9 figs., 3 tabs.

01 COAL, LIGNITE, AND PEAT↗

Meso- and micropore characteristics of coal lithotypes: implications for CO{sub 2} adsorption

Lithotypes of high volatile bituminous Pennsylvanian coals from Indiana (the Illinois Basin) have been studied with regard to meso- and micropore characteristics using low-pressure nitrogen and carbon dioxide adsorption techniques, respectively. High-pressure CO{sub 2} adsorption isotherms were obtained and after evacuation of CO{sub 2}, the lithotypes were re-analyzed for meso- and micropore characteristics to investigate changes related to high-pressure CO{sub 2} adsorption. Coal lithotypes have differing Brunauer-Emmett-Teller (BET) surface areas and mesopore volumes, with significantly lower values in fusains than in vitrains or clarains. In the Springfield and the Lower Block Coal Members, among lithotypes studied, fusain has the lowest adsorption capacity. For the Lower Block, vitrain has significantly higher adsorption capacity than fusain and clarain, whereas for the Springfield, vitrain and clarain have comparable but still significantly higher adsorption capacities than fusain. The Lower Block vitrain and fusain have much higher adsorption capacities than those in the Springfield, whereas the clarains of the two coals are comparable. After exposure of coal to CO{sub 2} at high pressure, vitrains experienced the largest porosity changes among all lithotypes studied. These changes are dominantly manifested in the mesoporosity (decrease in mesopore volume) range, whereas little to no change occurred in the micropore size range. In other lithotypes (clarains, the dominant lithology in the coals studied, and sporadic fusains), the changes were minimal. 41 refs., 11 figs., 8 tabs.

01 COAL, LIGNITE, AND PEAT↗

Study on the stability of sorbents removing H{sub 2}S from hot coal gas

Mixed metal oxide containing iron with the high-sulfur capacity and reactivity is considered as one of the most favorable sorbents for desulfurization in hot gas. The stability and life of iron-based sorbents are the main challenges for the hot gas cleanup techniques. Not only the effect of gas atmosphere but also the effect of ZnO and MgO on the stability of iron-based sorbent was studied in this work. The mechanism and factors influencing sorbent stability are discussed. The results showed that the coexistence of CO and H{sub 2} result in the instability of the zinc-iron-based sorbents. The reaction of carbon deposit is the crucial step affecting the stability of sorbent for hot gas desulfurization. ZnO in the sorbent is adverse to the physical stability of the iron-based sorbents. MgO in the sorbent hardly affects the physical stability of the iron-based sorbents but improves the capacity of removing the hydrogen sulfide from hot coal gas at 773 K. 12 refs., 8 figs., 5 tabs.

01 COAL, LIGNITE, AND PEAT↗

NO reduction in decoupling combustion of biomass and biomass-coal blend

Biomass is a form of energy that is CO{sub 2}-neutral. However, NOx emissions in biomass combustion are often more than that of coal on equal heating-value basis. In this study, a technology called decoupling combustion was investigated to demonstrate how it reduces NO emissions in biomass and biomass-coal blend combustion. The decoupling combustion refers to a two-step combustion method, in which fuel pyrolysis and the burning of char and pyrolysis gas are separated and the gas burns out during its passage through the burning-char bed. Tests in a quartz dual-bed reactor demonstrated that, in decoupling combustion, NO emissions from biomass and biomass-coal blends were both less than those in traditional combustion and that NO emission from combustion of blends of biomass and coal decreased with increasing biomass percentage in the blend. Co-firing rice husk and coal in a 10 kW stove manufactured according to the decoupling combustion technology further confirmed that the decoupling combustion technology allows for truly low NO emission as well as high efficiency for burning biomass and biomass-coal blends, even in small-scale stoves and boilers. 22 refs., 6 figs., 1 tab.

01 COAL, LIGNITE, AND PEAT↗