Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Jet Surface”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1976

Noise generated by impingement of turbulent flow on airfoils of varied chord, cylinders, and other flow obstructions

Noise spectra were measured in three dimensions for several surfaces immersed in turbulent flow from a jet and over a range of flow conditions. The data are free field and were corrected to remove the small contributions of jet noise, atmospheric attenuation and feedback tones. These broadband data were compared with the results of available theories which are only strictly applicable to simple geometries over a limited range of conditions. The available theories proved to be accurate over the range of flow, chord length, thickness, angle of attack, and surface geometries defined by the experiments. These results apply to the noise generated by fixed surfaces in engine passages, the lifting surfaces of aircraft and also to fan noise.

Olsen, W. A.↗
DOE OSTI2021

Attached and Attaching Three-Dimensional Jets from Circular Nozzles: Analytical Model

Here we evaluate velocity profiles of three dimensional attached jets emerging from circular nozzles. These jets lose momentum due to interactions with nearby surfaces and are important to evaluating flows in mixing vessels and to suspending solids and trapped gases in radioactive waste tanks. Despite the industrial importance of attached jets, simple, complete, and quantitative expressions for their velocity profiles remain elusive. Here we present a quantitative analytical model of the three dimensional velocity profiles of attached jets inclusive of a local skin coefficient of friction. We compare these expressions to experimental velocity profiles at moderate and high nozzle Reynolds numbers to find reasonable quantitative agreement.

Jet, attached jet, offset jet, reattaching offset ↗
NASA NTRS1988

Effect of surface catalysis on heating to ceramic coated thermal protection systems for transatmospheric vehicles

This paper describes the effect of surface catalysis on the heat transfer rate to the heat shield of a typical Transatmospheric Vehicle (TAV) during ascent and atmospheric entry. Surface kinetics and optical properties obtained from arc-jet tests on candidate thermal protection systems (coated metals) were used in a reacting boundary layer code to estimate the heating distribution along the surface of a TAV. Thermochemical stability of the coatings is described in terms of reduction in emittance and loss of opacifiers from the coatings during the arc-jet tests.

Stewart, David A.↗
NASA NTRS1983

Porous-plug flowfield mechanisms for reducing supersonic jet noise

An experimental investigation was performed to characterize the changes in jet flowfield properties associated with noise reduction obtained by using porous-plug nozzles at supersonic pressure ratios. A series of constant-exit-area nozzles with various plug sizes was investigated over the Mach number range 0.8-1.4. Periodic shock cells were observed in the flow for a solid plug. For a porous surface, the shock cells are replaced by a gradual compression composed of multiple weak shocks originating at the surface holes. Reduction of far-field jet noise correlates with a decrease of the pressure cell strength.

Kibens, V.↗
NASA NTRS1982

Dip-Coating Fabrication of Solar Cells

Inexpensive silicon solar cells made by simple dip technique. Cooling shoes direct flow of helium on graphite-coated ceramic substrate to solidify film of liquid silicon on graphite surface as substrate is withdrawn from molten silicon. After heaters control cooling of film and substrate to prevent cracking. Gas jets exit at points about 10 mm from substrate surfaces and 6 to 10 mm above melt surface.

Koepke, B.↗
DOE OSTI2021

Fabrication and durability characterization of superhydrophobic and lubricant-infused surfaces

Hypothesis: Practical applications of non-wetting surfaces require good mechanical durability in the wet environments for which they are intended to be used. Durability of non-wetting surfaces is influenced by the surface features, interaction with the functionalization agent, and the lubricant properties that can be tuned independently to identify optimal combination. Experiments: In this study, superhydrophobic and lubricant-infused surfaces are fabricated on copper tubes using chemical etching and electrodeposition texturing techniques, six different functionalizing agents, and five different infused lubricants. Through 180 fabrication combinations and 102 durability tests, each parameter is systematically studied for contributions to initial non-wetting behavior and its durability in heated, wet environment, under high-energy water jet impingement, and under accelerated flow conditions. Findings: Among the adsorbing and curing functionalization agents investigated, n-Hexadecyl mercaptan that belongs to the sulfhydryl group and Sylgard-184, respectively, showed high durability in heated water immersion and under jet impingement tests. For lubricant-infused surfaces, lubricants with high surface tension demonstrated high durability in heated water immersion test, whereas durability in hydrodynamic conditions is closely correlated to lubricant viscosity. Results showed that a lubricant-infused surface will maintain its non-wetting properties in dropwise condensation conditions for approximately 1.5 years.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Sweeping Jet Film Cooling at High Blowing Ratio on a Turbine Vane

Abstract Experimental and numerical investigations were performed to study the effects of high blowing ratios and high freestream turbulence on sweeping jet film cooling. Experiments were conducted on a nozzle guide vane suction surface in a low-speed linear cascade at a range of blowing ratios of 0.5–3.5 and freestream turbulence of 0.6% and 14.3%. Infrared thermography was used to estimate the adiabatic cooling effectiveness. Thermal field and boundary layer measurements were conducted at a cross-plane at x/D = 12 downstream of the hole exit. Results were compared with a baseline 777-shaped hole and showed that the sweeping jet hole has improved cooling effectiveness at high blowing ratios (M > 1). The thermal field data revealed that the coolant separates from the surface at high blowing ratios for the 777-shaped hole while the coolant remains attached for the sweeping jet hole. Boundary layer measurements further confirmed that due to the sweeping motion of the jet, the effective jet momentum of the sweeping jet hole remains much lower than that of a 777-shaped hole. Thus, the coolant remains closer to the wall even at high blowing ratios. Large Eddy simulations (LES) were performed for both the sweeping jet and 777-shaped hole to evaluate the interaction between the coolant jet and the freestream in the near hole regions. Results showed that 777-shaped hole has a strong jetting at high blowing ratio that originates inside the hole breakout edges thus causing the jet to blow-off from the surface. In contrast, the sweeping jet does not show this behavior due to its internal geometry and flapping motion of the jet.

Engineering↗
NASA NTRS1976

Theoretical predictions of jet interaction effects for USB and OWB configurations

A wing jet interaction theory is presented for predicting the aerodynamic characteristics of upper surface blowing and over wing blowing configurations. For the latter configurations, a new jet entrainment theory is developed. Comparison of predicted results with some available data showed good agreement. Some applications of the theory are also presented.

Lan, C. E.↗
NASA NTRS2018

Nozzle Plume/Shock Interaction Experimental and Computational Sonic Boom Analyses from the NASA Ames 9- by 7-Foot Supersonic Wind Tunnel

A wind tunnel test and a computational study were conducted to investigate the complex interactions between a supersonic nozzle plume and shock waves of differing strengths generated from various aft surfaces typical of supersonic aircraft. These analytically-defined aft surfaces were representative of horizontal tails of various sizes, and an aft deck. CFD simulations of many proposed model configurations allowed for assessments of the detailed flow interactions of components in close proximity to the nozzle, as well as assessments of the nozzle jet flow itself. The evaluation of the computational results for many candidate configurations guided the design of model components. The interactions of the waveforms from these surfaces with the jet exhaust plume can have significant adverse effects on the loudness of the sonic boom if the surfaces are not carefully integrated into an aircraft design. The greatest discrepancy in estimating sonic boom loudness for low-boom flight vehicles is currently in predicting the signatures from the aft part of an aircraft, including the interactions with the plume flow. The objectives of this test were to gain a better understanding of these interactions, and to provide a detailed experimental database from multiple sources for use as validation cases for CFD tool development. The subject test was run in the NASA Ames 9- by 7-Ft Supersonic Wind Tunnel in February 2016 at Mach numbers of 1.6 and 2.0, and was funded by the NASA Commercial Supersonics Technology (CST) Project. The nozzle flow was provided by high-pressure air (HPA) pumped through the model, and pressure signature data were acquired with the NASA 14-inch sonic boom pressure rail. The rail measured the locations of the shocks and expansions at various distances and off-track angles from the model. This enabled the impact of the nozzle plume/shock interactions on the near- and mid-field sonic boom pressure waveforms to be quantified. Schlieren images of the flow field around and behind the model were obtained with an RBOS (Retroreflective Background-Oriented Schlieren) technique to determine the origins of the shock and expansion waves, to identify the shape and boundaries of the plume, and to determine the changes in incoming and exiting waveforms within the plume. A total pressure rake was positioned closely behind the model nozzle in order to measure the total pressure profiles of the flow above, within, and below the nozzle exhaust. Model angles and positions in the tunnel were measured by photogrammetry using two cameras since the lack of a model force balance prevented the measurement of model deflections under load.Navier-Stokes computations using two different CFD codes were compared to the experimental sonic boom pressure signature data, and the rake total pressure data in the plume. A computational schlieren technique was used to compare the computed flow field with the RBOS images. The computational results were also used to complement the test data with flow field quantities that could not be measured, such as Mach number and pressure distributions to distinguish shock waves and expansion waves.

sonic boom↗
NASA NTRS1999

Active Control of Flow Separation Over an Airfoil

Designing an aircraft without conventional control surfaces is of interest to aerospace community. In this direction, smart actuator devices such as synthetic jets have been proposed to provide aircraft maneuverability instead of control surfaces. In this article, a numerical study is performed to investigate the effects of unsteady suction and blowing on airfoils. The unsteady suction and blowing is introduced at the leading edge of the airfoil in the form of tangential jet. Numerical solutions are obtained using Reynolds-Averaged viscous compressible Navier-Stokes equations. Unsteady suction and blowing is investigated as a means of separation control to obtain lift on airfoils. The effect of blowing coefficients on lift and drag is investigated. The numerical simulations are compared with experiments from the Tel-Aviv University (TAU). These results indicate that unsteady suction and blowing can be used as a means of separation control to generate lift on airfoils.

Ravindran, S. S.↗
NASA NTRS1983

Gear Lubrication and Cooling Experiment and Analysis

A gear tooth temperature analysis was performed using a finite element method combined with a calculated heat input, a calculated oil jet impingement depth, and estimated heat transfer coefficients for the different parts of the gear tooth that are oil cooled and air cooled. Experimental measurements of gear tooth average surface temperature and gear tooth instantaneous surface temperature were made with a fast response, infrared, radiometric microscope. Increasing oil pressure has a significant effect on both average surface temperature and peak surface temperature at loads above 1895 N/cm(1083 lb/in) and speeds of 10,000 and 7500 rpm. Both increasing speed (from 5000 to 10,000 rpm) at constant speed cause a significant rise in the average surface temperature and in the instantaneous peak surface temperatures on the gear teeth. The oil jet pressure required to provide the best cooling for gears is the pressure required to obtain full gear tooth impingement. Calculated results for gear tooth temperatures were close to experimental results for various oil jet impingement depths for identical operating conditions.

Townsend, D. P.↗
NASA NTRS1999

Investigation of Strain/Vorticity and Large-Scale Flow Structure in Turbulent Nonpremixed Jet Flames

Our study will use the microgravity environment to investigate the underlying flow structure of turbulent nonpremixed round jet flames. In particular, we aim to investigate the large-scale turbulent structure using planar laser Mie scattering (PLMS), and the strain rate and vorticity fields using particle image velocimetry (PIV). This work is motivated by recent studies in our laboratory that have led to several interesting observations of nominally momentum-driven turbulent nonpremixed planar flames. First of all, the organized large-scale turbulent structures that are observed in nonreacting planar jets may be substantially modified or suppressed in nonpremixed planar jet flames. Furthermore, a recent study using PIV and planar laser-induced fluorescence of OH has shown that in transitional and turbulent nonpremixed planar jet flames the presence of the flame seems to greatly influence the underlying vorticity and strain fields, as compared to nonreacting jets. For example, the reaction zones in the jet flames are strongly correlated with regions of high vorticity. A related study has demonstrated that vorticity is not correlated in the same way with either iso-scalar surfaces or scalar dissipation layers in nonreacting planar jets. Furthermore, the relationship between strain and the reaction zone appears to be modified by the presence of high levels of heat release. In particular, the strain rate field in planar jet flames exhibits a preferred direction of principal compressive strain that apparently is related to strong shear across the reaction zone. This preferred direction of strain was not observed in nonreacting jets. One of the major problems encountered when conducting these types of studies is that it is difficult to know to what extent buoyancy influences the results. Therefore, the microgravity environment provides us with an excellent opportunity to explore these issues without the complicating effects of buoyancy. This is particularly the case when studying flames that are transitional between laminar and turbulent states. For example, the strong correlation of vorticity with the reaction zone (discussed above) was observed in both transitional and turbulent planar flames, but the effect was stronger for the transitional case. To date, the reason for the presence of the vorticity-reaction zone correlation is not known, although vorticity production via baroclinic torque is a likely cause. The microgravity environment will allow us to specifically determine whether the vorticity is produced by baroclinic torque resulting from the flame density gradient acting with the hydrostatic pressure gradient.AAdditional details of the planned experiments are provided.

Clemens, N. T.↗
NASA NTRS2007

Granular Mechanics and Surface Systems Lab

The cratering of sand under gas jets is observed to further understanding of soil in hopes to further understand lunar soil. Lunar soil is important to understand because it is causing problems with the materials taken into space including the shuttle. Lunar soil is not rounded like beach sand. Lunar soil is sharp like little particles of glass, and some times when blown they can hook on to one another and become bigger particles. The experiments are designed to help to understand some of the basic physics in how the shuttle jets will interact with lunar soil and how to control the lunar soil. These experiments investigate the diameter of the gas jet and the size of the sand grains to determine how these parameters affect the erosion rate and the cratering processes. Therefore, the experiments preformed will point out what is dependent and what is independent.

Randle, Leah↗
DOE OSTI2020

Electric field dynamics in an atmospheric pressure helium plasma jet impinging on a substrate

Time and spatially resolved electric field measurements by Stark polarization spectroscopy in a nanosecond pulsed atmospheric pressure helium jet operating in ambient air and impinging on a conductive indium tin oxide (ITO) coated glass slide are reported. An automatic fitting procedure of the Stark shifted spectra taking into consideration constraints regarding Stark components positions and intensities as well as molecular nitrogen emission subtraction was implemented. This allowed electric field vector components measurements both in the gas phase and at the interface when the jet impinges on the substrate and during the development of a surface ionization wave. The obtained results show an increase of the axial electric field in the jet effluent in the gas phase with a peak magnitude from 12 to 18 kVcm -1 before the ionization wave impinges on the substrate. A steep electric field enhancement to a peak value of about 24 kVcm -1 was observed when the ionization wave impinges on the surface. A peak radial electric field of about 27 kVcm -1 was measured off-axis in the surface ionization wave. These results are consistent with previously reported modelling predictions. While Stark polarization spectroscopy is limited to electric field measurement from regions with emission, we illustrate that the capability to measure near surface electric fields in helium makes it a valuable complementary technique for the electric field-induced second harmonic (E-FISH) technique.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Selectivity in gas–liquid interactions: Molecular beam scattering of CD 4 and ND 3 from an aqueous flat liquid jet

The dynamics of polar and nonpolar molecules colliding with an aqueous surface are characterized by scattering molecular beams of deuterated methane and ammonia, CD 4 and ND 3 (E i = 28.9 and 30.3 kJ mol −1 , respectively), from a flat liquid jet of cold salty water (8 m LiBr, 230 K). Translational energy distributions of scattered species collected as a function of collision geometry probe both impulsive scattering (IS) and thermal desorption (TD) mechanisms. Here, we find that CD 4 scattering is dominated by IS and exhibits a super-specular angular distribution. The fraction of TD scattering events is notably smaller for cold salty water than for dodecane, consistent with a higher free energy of solvation for CD 4 in the water jet. In contrast, no scattering signal is seen for ND 3 from the water jet, a result attributed to the high solubility and efficient protonation of ND 3 in liquid water. The IS channel for CD 4 was analyzed using a soft-sphere model, yielding a higher internal energy (E int ) and lower effective surface mass (m eff ) than was seen for Ne/water; the higher value of E int is attributed to rotational excitation of the scattered CD 4 . These findings demonstrate that the outcomes of a gas–liquid collision—scattering trajectory, surface adherence, and energy transfer—are directed at the molecular level by both the gaseous scatterer and liquid surface.

Foreman, Madison M. [University of California, Ber↗
NASA NTRS2003

Toward the Active Control of Heat Transfer in the Hot Gas Path of Gas Turbines

The work at NASA this summer has focused on assisting the Professor's project, namely "Toward the Active Control of Heat Transfer in the Hot Gas Path of Gas Turbines." The mode of controlling the Heat Transfer that the project focuses on is film cooling. Film cooling is used in high temperature regions of a gas turbine and extends the life of the components exposed to these extreme temperatures. A "cool" jet of air is injected along the surface of the blade and this layer of cool air shields the blade from the high temperatures. Cool is a relative term. The hot gas path temperatures reach on the order of 1500 to 2000 K. The "coo" air is on the order of 700 to 1000 K. This cooler air is bled off of an appropriate compressor stage. The next parameter of interest is the jet s position and orientation in the flow-field.

Oertling, Jeremiah E.↗
NASA NTRS1993

Lift augmentation for highly swept wing aircraft

A pair of spaced slots, disposed on each side of an aircraft centerline and spaced well inboard of the wing leading edges, are provided in the wing upper surfaces and directed tangentially spanwise toward thin sharp leading wing edges of a highly swept, delta wing aircraft. The slots are individually connected through separate plenum chambers to separate compressed air tanks and serve, collectively, as a system for providing aircraft lift augmentation. A compressed air supply is tapped from the aircraft turbojet power plant. Suitable valves, under the control of the aircraft pilot, serve to selective provide jet blowing from the individual slots to provide spanwise sheets of jet air closely adjacent to the upper surfaces and across the aircraft wing span to thereby create artificial vortices whose suction generate additional lift on the aircraft. When desired, or found necessary, unequal or one-side wing blowing is employed to generate rolling moments for augmented lateral control. Trailing flaps are provided that may be deflected differentially, individually, or in unison, as needed for assistance in take-off or landing of the aircraft.

Rao, Dhanvada M.↗