Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Heat conduction modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS2017

Pressurization of a Flightweight, Liquid Hydrogen Tank: Evaporation & Condensation at a Liquid/Vapor Interface

This paper presents an analysis and simulation of evaporation and condensation at a motionless liquid/vapor interface. A 1-D model equation, emphasizing heat and mass transfer at the interface, is solved in two ways, and incorporated into a subgrid interface model within a CFD simulation. Simulation predictions are compared with experimental data from the CPST Engineering Design Unit tank, a cryogenic fluid management test tank in 1-g. The numerical challenge here is the physics of the liquid/vapor interface; pressurizing the ullage heats it by several degrees, and sets up an interfacial temperature gradient that transfers heat to the liquid phase-the rate limiting step of condensation is heat conducted through the liquid and vapor. This physics occurs in thin thermal layers O(1 mm) on either side of the interface which is resolved by the subgrid interface model. An accommodation coefficient of 1.0 is used in the simulations which is consistent with theory and measurements. This model is predictive of evaporation/condensation rates, that is, there is no parameter tuning.

Stewart, Mark E. M.↗
NASA NTRS1975

Heat transfer phase change paint tests of 0.0175-scale models (nos. 21-0 and 46-0) of the Rockwell International space shuttle orbiter in the AEDC tunnel B hypersonic wind tunnel (test OH25A)

Tests were conducted in a hypersonic wind tunnel using various truncated space shuttle orbiter configurations in an attempt to establish the optimum model size for other tests examining body shock-wing leading edge interference effects. The tests were conducted at Mach number 8 using the phase change paint technique. A test description, tabulated data, and tracings of isotherms made from photographs taken during the test are presented.

Dye, W. H.↗
NASA NTRS1992

A PC-based collapse factor analysis for high pressure cryogenic systems

A collapse factor simulation computer program, suitable for use on personal computers, for supercritical cryogen system pressurization is examined. The available literature is previewed, individual component models are developed, and the overall simulation program logic is examined. Extensive use is made of existing thermodynamic and transport property evaluation packages. Heat transfer is estimated using natural convection correlations, and transient wall heat conduction is considered. Examples of the simulation are demonstrated for two facilities. Partial validation is achieved by comparing the simulation output with data from an existing test facility. Preliminary results indicate that the collapse factors will seldom exceed 1.15 during supercritical operation of high-pressure cryogenic systems. Recommendations for improvements in the component models and the simulation are made.

Hodge, B. K.↗
NASA NTRS2012

Emission Spectroscopy and Radiometric Measurements in the NASA Ames IHF Arc Jet Facility

Plasma diagnostic measurement campaigns in the NASA Ames Interaction Heating Facility (IHF) have been conducted over the last several years with a view towards characterizing the flow in the arc jet facility by providing data necessary for modeling and simulation. Optical emission spectroscopy has been used in the plenum and in the free jet of the nozzle. Radiation incident over a probe surface has also been measured using radiometry. Plenum measurements have shown distinct radial profiles of temperature over a range of operating conditions. For cases where large amounts of cold air are added radially to the main arc-heated stream, the temperature profiles are higher by as much as 1500 K than the profiles assumed in flow simulations. Optical measurements perpendicular to the flow direction in the free jet showed significant contributions to the molecule emission through inverse pre-dissociation, thus allowing determination of atom number densities from molecular emission. This has been preliminarily demonstrated with the N2 1st Positive System. Despite the use of older rate coefficients, the resulting atom densities are reasonable and surprisingly close to flow predictions.

Winter, Michael W.↗
NASA NTRS1990

Coupled effects of conduction in the crystal and thermo-solutal convection in a rectangular inclined enclosure

To date modeling of crystal growth of optoelectronic materials using Physical Vapor Transport has been limited to the study of the fluid phase. To achieve it, the equations of coupled heat, mass and momentum transfer in the gas have to be solved. The first objective of this study is to examine the effect of heat conduction in the crystal on the fluid flow in the neighborhood of the interface. Heat transfer boundary conditions on both interfaces were modified to take into account the additional heat flux between gas and solid. It is proved that heat conduction does not affect the fluid flow. In the presence of gravity, density gradients in the fluid phase generate convection responsible for the problem of a nonplanar growth of the interface. The second objective is to study systematically under one-g the different possible flows in order to solve this problem. Depending on the parameters, a diffusive mode and three convective modes (thermal, solutal and thermo-solutal) are observed. The competition between thermal and solutal convections leads to a mathematical condition which can be used to achieve a planar growth. It is proven that, under the physical conditions chosen, this mathematical condition cannot be thermodynamically satisfied.

Mennetrier, Christophe↗
NASA NTRS1990

Modeling solar flare conduction fronts. I - Homogeneous plasmas and ion-acoustic turbulence. II - Inhomogeneous plasmas and ambipolar electric fields

A one-dimensional, electrostatic, particle-in-cell simulation is used here to model the expansion of a heated electron population in a coronal loop during a solar flare and the characteristics of the associated X-ray emissions. The hot electrons expand outward from the localized region, creating an ambipolar electric field which accelerates a return current of cooler, ambient electrons. Ion-acoustic waves are generated by the return currents as proposed by Brown et al. (1979), but they play little or no role in containing energetic electrons and the conduction front proposed by Brown et al. does not form. The X-ray emission efficiency of the electrons is too low in the corona for them to be the source of hard X-ray bursts. The particle dynamics changes dramatically if the heated plasma is at low altitudes and expands upward into the more tenuous plasma at higher altitudes. Two important applications of this finding are the radio-frequency heating of the corona and the collisional heating of the chromosphere by precipitating energetic electrons. In both cases, the overlying plasma has a density that is too low to supply a balancing return current to the expanding hot electrons. As a result, an ambipolar electric field develops that tends to confine the energetic electrons behind a front that propagate outward at about the speed of sound.

Mckean, M. E.↗
NASA NTRS2015

Evaluation of Finite-Rate Gas/Surface Interaction Models for a Carbon Based Ablator

Two sets of finite-rate gas-surface interaction model between air and the carbon surface are studied. The first set is an engineering model with one-way chemical reactions, and the second set is a more detailed model with two-way chemical reactions. These two proposed models intend to cover the carbon surface ablation conditions including the low temperature rate-controlled oxidation, the mid-temperature diffusion-controlled oxidation, and the high temperature sublimation. The prediction of carbon surface recession is achieved by coupling a material thermal response code and a Navier-Stokes flow code. The material thermal response code used in this study is the Two-dimensional Implicit Thermal-response and Ablation Program, which predicts charring material thermal response and shape change on hypersonic space vehicles. The flow code solves the reacting full Navier-Stokes equations using Data Parallel Line Relaxation method. Recession analyses of stagnation tests conducted in NASA Ames Research Center arc-jet facilities with heat fluxes ranging from 45 to 1100 wcm2 are performed and compared with data for model validation. The ablating material used in these arc-jet tests is Phenolic Impregnated Carbon Ablator. Additionally, computational predictions of surface recession and shape change are in good agreement with measurement for arc-jet conditions of Small Probe Reentry Investigation for Thermal Protection System Engineering.

Ablation↗
NASA NTRS1994

Radiative interactions in multi-dimensional chemically reacting flows using Monte Carlo simulations

The Monte Carlo method (MCM) is applied to analyze radiative heat transfer in nongray gases. The nongray model employed is based on the statistical narrow band model with an exponential-tailed inverse intensity distribution. The amount and transfer of the emitted radiative energy in a finite volume element within a medium are considered in an exact manner. The spectral correlation between transmittances of two different segments of the same path in a medium makes the statistical relationship different from the conventional relationship, which only provides the non-correlated results for nongray methods is discussed. Validation of the Monte Carlo formulations is conducted by comparing results of this method of other solutions. In order to further establish the validity of the MCM, a relatively simple problem of radiative interactions in laminar parallel plate flows is considered. One-dimensional correlated Monte Carlo formulations are applied to investigate radiative heat transfer. The nongray Monte Carlo solutions are also obtained for the same problem and they also essentially match the available analytical solutions. the exact correlated and non-correlated Monte Carlo formulations are very complicated for multi-dimensional systems. However, by introducing the assumption of an infinitesimal volume element, the approximate correlated and non-correlated formulations are obtained which are much simpler than the exact formulations. Consideration of different problems and comparison of different solutions reveal that the approximate and exact correlated solutions agree very well, and so do the approximate and exact non-correlated solutions. However, the two non-correlated solutions have no physical meaning because they significantly differ from the correlated solutions. An accurate prediction of radiative heat transfer in any nongray and multi-dimensional system is possible by using the approximate correlated formulations. Radiative interactions are investigated in chemically reacting compressible flows of premixed hydrogen and air in an expanding nozzle. The governing equations are based on the fully elliptic Navier-Stokes equations. Chemical reaction mechanisms were described by a finite rate chemistry model. The correlated Monte Carlo method developed earlier was employed to simulate multi-dimensional radiative heat transfer. Results obtained demonstrate that radiative effects on the flowfield are minimal but radiative effects on the wall heat transfer are significant. Extensive parametric studies are conducted to investigate the effects of equivalence ratio, wall temperature, inlet flow temperature, and nozzle size on the radiative and conductive wall fluxes.

Liu, Jiwen↗
NASA NTRS1994

A Method for Thermal Analysis of Spiral Bevel Gears

A modeling method for analyzing the three-dimensional thermal behavior of spiral bevel gears has been developed. The model surfaces are generated through application of differential geometry to the manufacturing process for face-milled spiral bevel gears. Contact on the gear surface is found by combining tooth contact analysis with three-dimensional Hertzian theory. The tooth contact analysis provides the principle curvatures and orientations of the two surfaces. This information is then used directly in the Hertzian analysis to find the contact size and maximum pressure. Heat generation during meshing is determined as a function of the applied load, sliding velocity, and coefficient of friction. Each of these factors change as the point of contact changes during meshing. A nonlinear finite element program was used to conduct the heat transfer analysis. This program permitted the time- and position-varying boundary conditions, found in operation, to be applied to a one-tooth model. An example model and analytical results are presented.

Handschuh, Robert F.↗
NASA NTRS1974

Thermal preparation of foods in space-vehicle environments

Convection is the primary heat transfer mechanism for most foods heated in an earth-based environment. In contrast, in the low-gravity environment of space flight, the primary heat transfer mechanism is conduction (or radiation in the absence of a conducting medium). Conduction heating is significantly slower and less efficient than convection heating. This fact poses a problem for food heating during space flight. A numerical model has been developed to evaluate this problem. This model simulates the food-heating process for Skylab. The model includes the effect of a thermally controlled on/off heat flux. Parametric studies using this model establish how the required heating time is affected by: the thermal diffusivity of the nutrient materials, the power level of the heater, the initial food temperatures, and the food container dimensions.

Bannerot, R. B.↗
NASA NTRS1980

On the performance of explicit and implicit algorithms for transient thermal analysis

The status of an effort to increase the efficiency of calculating transient temperature fields in complex aerospace vehicle structures is described. The advantages and disadvantages of explicit and implicit algorithms are discussed. A promising set of implicit algorithms, known as the GEAR package is described. Four test problems, used for evaluating and comparing various algorithms, have been selected and finite element models of the configurations are discribed. These problems include a space shuttle frame component, an insulated cylinder, a metallic panel for a thermal protection system and a model of the space shuttle orbiter wing. Calculations were carried out using the SPAR finite element program, the MITAS lumped parameter program and a special purpose finite element program incorporating the GEAR algorithms. Results generally indicate a preference for implicit over explicit algorithms for solution of transient structural heat transfer problems when the governing equations are stiff. Careful attention to modeling detail such as avoiding thin or short high-conducting elements can sometimes reduce the stiffness to the extent that explicit methods become advantageous.

Adelman, H. M.↗
NASA NTRS1982

Conjugated heat transfer in a laminar boundary layer with heat source at the wall

This work presents the solution of the temperature field in a two-dimensional laminar incompressible flow over a conducting solid plate with a line heat source located at the fluid-solid interface perpendicular to the flow direction. A numerical scheme was used to obtain the temperature profiles as a function of the source strength, and of the properties of the fluid and the solid. The heat conduction and forced convection in the fluid and the heat conduction in the solid were solved for the case of moderate temperature rise, where the assumption of constant properties applies. The model enables the improvement of an instrument for the detection of boundary layer separation. It was found that for the actual parameters of the separation detector, a distance of 4 to 24 mm between the sensors gives an indication of 70 percent of the maximum temperature difference.

Brosh, A.↗
NASA NTRS1992

Modeling the Martian seasonal CO2 cycle. I - Fitting the Viking Lander pressure curves. II - Interannual variability

The present diurnal and seasonal thermal model for Mars, in which surface CO2 frost condensation and sublimation are determined by the net effects of radiation, latent heat, and heat conduction in subsurface soil layers, in order to simulate seasonal exchanges of CO2 between the polar caps and atmosphere, successfully reproduces the measured pressured variations at the Viking Lander 1 site. In the second part of this work, the year-to-year differences between measured surface pressures at Viking sites as a function of season are used as upper limits on the potential magnitudes of interannual variations in the Martian atmosphere's mass. Simulations indicate that the dust layers deposited onto the condensing north seasonal polar cap during dust storms can darken seasonal frost deposits upon their springtime uncovering, while having little effect on seasonal pressure variations.

Wood, Stephen E.↗
NASA NTRS1992

A one-dimensional modeling study of carbonaceous haze effects on the springtime Arctic environment

The effect of carbonaceous Arctic haze on the surface energy balance was investigated using a specially developed one-dimensional three-component numerical model which accounts for the transfer of IR and solar radiation through the atmosphere, turbulent mixing within the boundary layer, and heat conduction through snow-capped sea ice. The results of calculations indicate that, when haze is present, the surface temperature increases, provided the relative humidity through the column does not change. The increase is due to an increase in the absorbed radiation at the surface.

Emery, Christopher A.↗
NASA NTRS1999

The Isothermal Dendritic Growth Experiment (IDGE)

The Isothermal Dendritic Growth Experiment (IDGE) constituted a series of three NASA-supported microgravity experiments, all of which flew aboard the space shuttle, Columbia. This experimental space flight series was designed and operated to grow and record dendrite solidification in the absence of gravity-induced convective heat transfer, and thereby produce a wealth of benchmark-quality data for testing solidification scaling laws. The data and analysis performed on the dendritic growth speed and tip size in Succinontrie (SCN) demonstrates that although the theory yields predictions that are reasonably in agreement with experiment, there are significant discrepancies. However, some of these discrepancies can be explained by accurately describing the diffusion of heat. The key finding involves recognition that the actual three-dimensional shape of dendrites includes time-dependent side-branching and a tip region that is not a paraboloid of revolution. Thus, the role of heat transfer in dendritic growth is validated, with the caveat that a more realistic model of the dendrite then a paraboloid is needed to account for heat flow in an experimentally observed dendrite. We are currently conducting additional analysis to further confirm and demonstrate these conclusions. The data and analyses for the growth selection physics remain much less definitive. From the first flight, the data indicated that the selection parameter, sigma*, is not exactly a constant, but exhibits a slight dependence on the supercooling. Additional data from the second flight are being examined to investigate the selection of a unique dendrite speed, tip size and shape. The IDGE flight series is now complete. We are currently completing analyses and moving towards final data archiving. It is gratifying to see that the IDGE published results and archived data sets are being used actively by other scientists and engineers. In addition, we are also pleased to report that the techniques and IDGE hardware system that the authors developed with NASA, are being currently employed on both designated flight experiments, like EDSE, and on flight definition experiments, like TDSE.

Glicksman, Martin E.↗
NASA NTRS1996

Modeling and Optimization of a High-Tc Hot-Electron Superconducting Mixer for Terahertz Applicaitons

The development of a YBa(sub 2)Cu(sub 3)O(sub 7-(kronecker delta))(YBCO) hot-electron bolometer (HEB) quasioptical mixer for a 2.5 heterodyne receiver is discussed. The modeled device is a submicron bridge made from a 10 nm thick film on a high thermal conductance substrate. The mixer performance expected for this device is analyzed in the framework of a two-temperature model which includes heating both of the electrons and the lattice. Also, the contribution of heat diffusion from the film through the substrate and from the film to the normal metal contacts is evaluated....a single sideband temperature of less than 2000k is predicted.

tetrahertz hot-electron bolometer quasioptical mix↗
NASA NTRSDate not supplied

Rapid Development of Instrument Thermal Models: Perspectives and Guidelines from NASA Goddard’s Instrument Design Laboratory

The Instrument Design Laboratory (IDL), part of NASA Goddard Space Flight Center’s Integrated Design Center (IDC), is a concurrent and collaborative environment which allows for rapid development of science instrumentation concepts within the span of less than two weeks. Science goals set by a Principal Investigator from government, industry or academia are translated into engineering requirements, from which a team of engineers spanning multiple disciplines use an established study process and a suite of analysis tools to work towards an instrument point design. As part of this process, a staff thermal engineer is tasked with designing a thermal control system which meets all incoming thermal requirements, while iterating real-time with other subsystems to ensure compatibility and functionality as a completed system. Thermal engineers on spaceflight projects typically have weeks or months to develop thermal models. However, the severe time limitation in this conceptual study setting makes thermal design particularly difficult, as rapid thermal modeling solely over the span of a few days is required to develop the instrument thermal design and understand the performance over its intended mission, especially if the instrument concept contains multiple thermal challenges such as dynamic environments or high heat dissipating components. In this paper, the authors provide a condensed guide for the most efficient ways to develop thermal models and conduct thermal analysis within the span of one-to-two weeks, as informed by decades of design experience and best practices in the IDL. The authors also focus on quick methods for determining worst-case thermal environments, deciding which modeling details are essential at this early phase, and quantifying the engineering resources necessary for thermal control. This paper concludes with specific thermal design tips for different instrument types across the electromagnetic spectrum.

Kan Yang↗
NASA NTRSDate not supplied

MEDLI2 Material Response Model Development and Validation

During the entry of Mars Science Laboratory (MSL) the heatshield was equipped with the instrumentation suite Mars Entry, Descent, and Landing Instruments (MEDLI). In-depth thermocouple (TC) data was used to reconstruct the surface heating and temperatures. Discrepancies between MEDLI’s recorded in-depth heating data and the predicted thermal response and recession led to a campaign to characterize and test Mars Entry, Descent, and Landing Instrument 2 (MEDLI2) flight lot thermal protection materials (TPS) at relevant temperatures and pressures for Martian entry conditions. This paper covers the development and validation of MEDLI2 flight lot material response models for the heatshield material Phenolic Impregnated Carbon Ablator (PICA) and the backshell material Super-Lightweight Ablator (SLA-561V). Virgin and char thermal conductivities were updated as a function of temperature and pressure in the MEDLI2 specific material response models. Other material properties such as virgin and char density, emissivity, absorptivity, and specific heat capacitance was also characterized and compared to the “Heritage” models used during the TPS design phase of Mars 2020. Fully Implicit Ablation and Thermal response (FIAT) simulations were completed using the Heritage and MEDLI2 material response models to provide evidence of the increased accuracy of the MEDLI2 model. FIAT predicted in-depth temperatures were compared to flight lot certification ground-test arc jet test data and MEDLI2 flight thermocouple data.

Material response↗