Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Graphite/Epoxy”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Computational simulation of intermingled-fiber hybrid composite behavior

Three-dimensional finite-element analysis and a micromechanics based computer code ICAN (Integrated Composite Analyzer) are used to predict the composite properties and microstresses of a unidirectional graphite/epoxy primary composite with varying percentages of S-glass fibers used as hydridizing fibers at a total fiber volume of 0.54. The three-dimensional finite-element model used in the analyses consists of a group of nine fibers, all unidirectional, in a three-by-three unit cell array. There is generally good agreement between the composite properties and microstresses obtained from both methods. The results indicate that the finite-element methods and the micromechanics equations embedded in the ICAN computer code can be used to obtain the properties of intermingled fiber hybrid composites needed for the analysis/design of hybrid composite structures. However, the finite-element model should be big enough to be able to simulate the conditions assumed in the micromechanics equations.

Mital, Subodh K.↗

Scaling of fiber composite structures

Structural scaling is being investigated using graphite/epoxy Z-section stiffeners loaded in compression. Sections of various web, flange and web-to-flange corner radii dimensions are being considered. Initial local buckling loads and modes have been determined analytically, numerically and by experiment. A normalizing parameter has been developed for initial buckling data. Postbuckling behavior has been evaluated numerically and experimentally. The nature of the load redistribution following buckling is a key factor in relating the response of the various section sizes. Additional experiments and the development of scaling parameters for postbuckling and crippling are underway.

Wieland, Todd M.↗

Longitudinal splitting in epoxy and K-polymer composites - Shear lag analysis including the effect of fiber bridging

The shear-lag model used previously by Nairn (1988) to derive a fracture mechanics analysis of longitudinal splitting in double-edge notched unidirectional composites was used to investigate the effect of fibers bridging across the longitudinal split in these composites. Using the new analysis, the longitudinal splitting fracture toughness, G(Lc), was determined for Hercules AS4/3501-6 graphite/epoxy laminates and for K-polymer based laminates containing Magnamite IM-6 as the graphite reinforcing fiber. Results show that the inclusion of the fiber bridging in the fracture analysis significantly affects the reported fracture toughness.

Nairn, John A.↗

Reliability analysis of composite laminates with load sharing

By viewing a composite lamina as a homogeneous solid whose directional strengths are random variables, lamina reliability under multiaxial stresses may be determined using either an interactive or a noninteractive criterion. From the reliability values for the individual laminae comprising a given laminate, Thomas and Wetherhold (1991) have proposed a method for determining bounds for the overall laminate reliability. In this paper, simple physically plausible phenomenological rules are proposed for redistribution of load after a lamina has failed within the confines of a laminate. These rules are illustrated by application to (0/ +/-15)s and (90/ +/-45/0)s graphite/epoxy laminates, and the results are compared to the previously proposed bounds.

Wetherhold, Robert C.↗

Effect of microstructure on the response of composite tubes

This paper addresses the effects of changes in the fiber content in the individual layers of a composite tube and the presence of resin-rich interplay regions on the torsional response of the tube. A micromechanics-based procedure is outlined to correct the properties of unidirectional graphite/epoxy obtained from flat coupon tests in order to account for the lower fiber volume fraction in the individual layers of a composite tube made from the same material. The corrected properties are used as input parameters to an analytical model developed to predict the response of composite tubes subjected to combined axial/torsion loading. It is illustrated that when the corrected properties and the resin-rich regions are included in the analysis, good correlation with experimental data is obtained.

Derstine, M. S.↗

Deformation and stress response of composite laminated shells under internal pressure

This paper presents a theoretical study of the response of filament wound composite shells under internal pressure. Each layer of the material is generally cylindrically anisotropic. By using cylindrically anisotropic elasticity field equations and Lekhnitskii's stress functions, a system of sixth-order ordinary differential equations is obtained. The general expressions for the stresses and displacements in the laminated composite shells under internal pressure are discussed. Two composite systems, graphite/epoxy and glass/epoxy, are selected to demonstrate the influence of degree of material anisotropy and fiber orientations on the axial and induced twisting deformation. Stress distributions of (45/-45)s symmetric angle-ply fiber-reinforced laminated shells are shown to illustrate the effect of radius-to-thickness ratio.

Yuan, F. G.↗

Compressive testing of filament-wound cylinders

An experimental investigation has been conducted on the compressive buckling and failure of filament-wound circular cylinders. This investigation identifies one of the relationships between structural performance and scale, as well as some of the causes of reduced structural performance in large-scale structures. It is hypothesized that this effect is related to two conditions: first, the number of fiber tow undulations; and second, the percentage of weak interfaces within the structure. The effect of winding pattern and the resulting location of the fiber undulations were studied by varying the winding parameters. Three types of cylinders were manufactured from Amoco T650-35/1908 graphite/epoxy preimpregnated tow with different winding sequences (0/+/-60)s, (+/-30/90)s, and (90/+/-30)s. The (90/+/-30)s cylinders were manufactured with two different winding patterns (distributed and classical) and radius-to-thickness ratios (15 and 55). All cylinders were loaded in compression to failure. Comparisons of the compressive strength and failure modes demonstrate the relationship between the winding parameters, scale, and structural performance of filament-wound composite cylinders.

Jensen, David W.↗

Sensitivity of the coefficients of thermal expansion of selected graphite reinforced composite laminates to lamina thermoelastic properties

An analytical study of the sensitivity of the laminate coefficient of thermal expansion, CTE, to changes in lamina elastic properties has been made. High modulus graphite/epoxy (P75/934, P100/934, P120/934), graphite/aluminum (P100/Al), and graphite/glass (HMS/Gl) composite materials were considered in quasi-isotropic, low thermal stress, and 'near-zero' thermal expansion laminate configurations. The effects of a positive or negative 10 percent change in lamina properties on laminate CTE is strongly dependent upon both the composite material and the laminate configuration. A 10 percent change in all of the lamina properties had very little effect on the laminate CTE of the HMS/Gl composite laminates investigated. The sensitivity and direction of change in the laminate CTE of Gr/934 depended very strongly on the fiber properties. A 10 percent change in the lamina transverse CTE resulted in changes as large as 0.216 ppm/C in the laminate CTE of a quasi-isotropic Gr/934 laminate. No significant difference was observed in the sensitivity of the laminate CTE of the P100/934 and P120/934 composite materials due to changes in lamina properties. Large changes in laminate CTE can result from measured temperature and radiation effects on lamina properties.

Tompkins, S. S.↗

A micromechanics-based progressive failure model for laminated composite structures

A micromechanics-based mechanistic model for progressive failure analysis of laminated composite shell structures is developed. A finite-element program for laminated shell analysis is coupled with a micromechanical elasticity solution for predicting failure and effective composite properties. The laminate model is based on a third-order shell theory which allows for both transverse normal and shearing deformations. Results are presented for the progressive failure of a (0/90(4)s graphite/epoxy laminate under uniaxial tension. The effect of fiber volume fraction in the 90-deg plies on laminate behavior was studied, and it was found that decreasing the fiber-volume fraction in the off-axis plies did not affect the laminate stiffness or the ultimate failure load, but significantly increased the load at which initial failure occurred.

Averill, R. C.↗

The upper bounds of reduced axial and shear moduli in cross-ply laminates with matrix cracks

The present study proposes a mathematical model utilizing the internal state variable concept for predicting the upper bounds of the reduced axial and shear stiffnesses in cross-ply laminates with matrix cracks. The displacement components at the matrix crack surfaces are explicitly expressed in terms of the observable axial and shear strains and the undamaged material properties. The reduced axial and shear stiffnesses are predicted for glass/epoxy and graphite/epoxy laminates. Comparison of the model with other theoretical and experimental studies is also presented to confirm direct applicability of the model to angle-ply laminates with matrix cracks subjected to general in-plane loading.

Lee, Jong-Won↗

Fracture analysis of transverse crack-tip and free-edge delamination in laminated composites

A shear deformation model including hygrothermal effects is developed for the analysis of local delaminations originating from transverse cracks in 90-deg plies located in and around the laminate midplane. A sublaminate approach is used and the model is applied to (+/- 25/90n)s T300/934 graphite/epoxy laminates for n values between 0.5 and 8, along with previously developed edge-delamination shear-deformation models. Critical loads and delamination modes are identified and compared with experimental results. Hygrothermal effects are included in all the models to make the comparisons realistic.

Armanios, Erian A.↗

Fatigue delamination onset prediction in unidirectional tapered laminates

Tapered (0 deg) laminates of S2/CE9000 and S2/SP250 glass/epoxies, and IM6/1827I graphite/epoxy were tested in cyclic tension. The specimens usually showed some initial stable delaminations in the tapered region, but these did not affect the stiffness of the specimens, and loading was continued until the specimens either delaminated unstably, or reached 10(exp 6) to 2 x 10 (exp 7) million cycles with no unstable delamination. The final unstable delamination originated at the junction of the thin and tapered regions. A finite-element model was developed for the tapered laminate with and without the initial stable delaminations observed in the tests. The analysis showed that for both cases the most likely place for an opening (Mode I) delamination to originate is at the junction of the taper and thin regions. For each material type, the models were used to calculate the strain energy release rate, G, associated with delaminations originating at that junction and growing either into the thin region or tapered region. For the materials tested, cyclic G(sub Imax) values from DCB tests were used with the maximum strain energy release rates calculated from the finite-element analysis to predict the onset of unstable delamination at the junction as a function of fatigue cycles. The predictions were compared to experimental values of maximum cyclic load as a function of cycles to unstable delamination from fatigue tests in tapered laminates. For the IM6/1827I and S2/SP250 laminates, the predictions agreed very well with the test data. Predicted values for the S2/CE9000 were conservative compared to the test data.

Murri, Gretchen B.↗

Failure mechanisms of uni-ply composite plates with a circular hole under static compressive loading

The objective of the study was to identify and study the failure mechanisms associated with compressive-loaded uniply graphite/epoxy square plates with a central circular hole. It is found that the type of compressive failure depends on the hole size. For large holes with the diameter/width ratio exceeding 0.062, fiber buckling/kinking initiated at the hole is found to be the dominant failure mechanism. In plates with smaller hole sizes, failure initiates away from the hole edge or complete global failure occurs. Critical buckle wavelengths at failure are presented as a function of the normalized hole diameter.

Khamseh, A. R.↗

Poly(Arylene Ether Imidazole) Surface Films

Films adhere well to some substrates, provide smooth surfaces, and facilitate release from molds. Thin films of thermoplastic poly(arylene ether imidazole)s (PAEI's) particularly suitable for use as surface modifiers for graphite/epoxy or graphite/bismaleimide composite panels. Molecule of PAEI includes imidazole groups along its backbone that co-cure with epoxies or bismaleimides during processing. Films thermally stable and resistant to bombardment by energetic electrons.

Connell, John W.↗

Design of a welded joint for robotic, on-orbit assembly of space trusses

A preliminary design for a weldable truss joint for on-orbit assembly of large space structures is described. The joint was designed for ease of assembly, for structural efficiency, and to allow passage of fluid (for active cooling or other purposes) along the member through the joint. The truss members were assumed to consist of graphite/epoxy tubes to which were bonded 2219-T87 aluminum alloy end fittings for welding on-orbit to truss nodes of the same alloy. A modified form of gas tungsten arc welding was assumed to be the welding process. The joint was designed to withstand the thermal and structural loading associated with a 120-ft diameter tetrahedral truss intended as an aerobrake for a mission to Mars.

Rule, W. K.↗

Design of a welded joint for robotic, on-orbit assembly of space trusses

In the future, some spacecraft will be so large that they must be assembled on-orbit. These spacecraft will be used for such tasks as manned missions to Mars or used as orbiting platforms for monitoring the Earth or observing the universe. Some large spacecraft will probably consist of planar truss structures to which will be attached special purpose, self-contained modules. The modules will most likely be taken to orbit fully outfitted and ready for use in heavy-lift launch vehicles. The truss members will also similarly be taken to orbit, but most unassembled. The truss structures will need to be assembled robotically because of the high costs and risks of extra-vehicular activities. Some missions will involve very large loads. To date, very few structures of any kind have been constructed in space. Two relatively simple trusses were assembled in the Space Shuttle bay in late 1985. Here the development of a design of a welded joint for on-orbit, robotic truss assembly is described. Mechanical joints for this application have been considered previously. Welded joints have the advantage of allowing the truss members to carry fluids for active cooling or other purposes. In addition, welded joints can be made more efficient structurally than mechanical joints. Also, welded joints require little maintenance (will not shake loose), and have no slop which would cause the structure to shudder under load reversal. The disadvantages of welded joints are that a more sophisticated assembly robot is required, weld flaws may be difficult to detect on-orbit, the welding process is hazardous, and welding introduces contamination to the environment. In addition, welded joints provide less structural damping than do mechanical joints. Welding on-orbit was first investigated aboard a Soyuz-6 mission in 1969 and then during a Skylab electron beam welding experiment in 1973. A hand held electron beam welding apparatus is currently being prepared for use on the MIR space station. Presently, Marshall Space Flight Center is evaluating processes appropriate for on-orbit welding. A low gravity environment has been found to have very minor effects on the welding processes appropriate for this application. This is based on tests run on-orbit as well as low gravity environments achieved by flying aircraft in parabolic trajectories. It appears that a modified form of gas tungsten arc welding (GTAW) will be most appropriate for welding together structures on-oribt. The process has been modified to work in a vacuum by providing gas to the arc zone by means of a hollow tungsten electrode with special shielding. A commercial tube welding head has been successfully modified for use on-orbit with a gas leakage rate of approximately 2.5 liters/min. To develop as realistic a joint as possible, a specific truss structure was selected on which to base the design. The structure considered was based on the 120 foot diameter aerobrake tetrahedral truss structure. The truss members were assumed to consist of graphite/epoxy tubes. Also, it was assumed that the nodes were constructed of 2219-T87 aluminum alloy. The magnitude of the member load assumed for design purposes was 100 kips.

Rule, William K.↗

PARAS program: Phased array radio astronomy from space

An orbiting radio telescope is proposed which, when operated in a Very Long Baseline Interferometry (VLBLI) scheme, would allow higher (than currently available) angular resolution and dynamic range in the maps, and the ability of observing rapidly changing astronomical sources. Using a passive phases array technology, the proposed design consists of 656 hexagonal modules forming a 150 meter diameter dish. Each observatory module is largely autonomous, having its own photovoltaic power supply and low-noise receiver and processor for phase shifting. The signals received by the modules are channeled via fiber optics to the central control computer in the central bus module. After processing and multiplexing, the data is transmitted to telemetry stations on the ground. The truss frame supporting each observatory pane is a hybrid structure consisting of a bottom graphite/epoxy tubular triangle and rigidized inflatable Kevlar tubes connecting the top observatory panel and bottom triangle. Attitude control and stationkeeping functions are performed by a system of momentum wheels in the bus and four propulsion modules located at the compass points on the periphery of the observatory dish. Each propulsion module has four monopropellant thrusters and six hydrazine arcjets, the latter supported by a nuclear reactor. The total mass of the spacecraft is 22,060 kg.

Jakubowski, Antoni K.↗

Stress distribution in composite flatwise tension test specimens

A finite element analysis was conducted to determine the stress distribution in typical graphite/epoxy composite flat wise tension (FWT) specimens under normal loading conditions. The purpose of the analysis was to determine the relationship between the applied load and the stress in the sample to evaluate the validity of the test as a means of measuring the out-of-plane strength of a composite laminate. Three different test geometries and three different material lay ups were modeled. In all cases, the out-of-plane component of stress in the test section was found to be uniform, with no stress concentrations, and very close to the nominal applied stress. The stress in the sample was found to be three-dimensional, and the magnitude of in-plane normal and shear stresses varied with the anisotropy of the test specimen. However, in the cases considered here, these components of stress were much smaller than the out-of-plane normal stress. The geometry of the test specimen had little influence on the results. It was concluded that the flat wise tension test provides a good measure of the out-of-plane strength for the representative materials that were studied.

Scott, Curtis A.↗