SEARCH · Engineering Papers

Results for “Grain Boundary”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

All sources NASA NTRS DOE OSTI

DOE OSTI2020

An Alternative Casting Technique to Improve the Creep Resistance of Cast INCONEL Alloy 740H

The increasing performance requirements of power plant designs, such as advanced-ultra supercritical (A-USC), require the use of Ni-based superalloys to replace high-strength, ferritic-martensitic steels for components subjected to temperatures above 898 K (625 °C) and for austenitic stainless steels components at temperatures above 973 K (700 °C). To date, commercial Ni-based superalloy INCONEL 740H has been shown to be appropriate for use in A-USC power plants as boiler components in a wrought product. However, large complex components in boilers as well as other casings in the turbine and valve chest require castings of a thick-wall nature. Using the alloy in its cast form would be significantly valuable in terms of range of component size, geometry and complexity. Previous investigations revealed short creep lives from cast INCONEL alloy 740H. Here in this investigation, an alternative casting route that utilized a melt procedure resulting in a fine-grain casting, and in conjunction with a computationally optimized homogenization heat treatment, not only controlled the grain size and grain boundary structure but minimized chemistry variability and segregation. A primarily equiaxed and homogenous grain size distribution was obtained from this approach with better repartition of M 23 C 6 carbides along the grain boundaries. Furthermore, better than 38 pct increase was obtained for this material in comparison to the creep life obtained from the best performing conventionally cast material. More importantly, the fine-grain homogenized (FGH) casting route resulted in the Larson–Miller plot for this material that coincided with that of wrought alloy 740. At low creep stresses (with a test still in progress), the FGH casting is resulting in higher values of the LMP than the wrought alloy.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Water-Surface Drag Coating: A New Route Toward High-Quality Conjugated Small-Molecule Thin Films with Enhanced Charge Transport Properties

Electronic properties of organic semiconductor (OSC) thin films are largely determined by their morphologies and crystallinities. However, solution-processed conjugated small-molecule OSC thin films usually exhibit abundant grain boundaries and impure grain orientations because of complex fluid dynamics during solution coating. Here, a novel methodology, water-surface drag coating, is demonstrated to fabricate high-quality OSC thin films with greatly enhanced charge transport properties. This method utilizes the water surface to alter the evaporation dynamics of solution to enlarge the grain size, and a unique drag-coating process to achieve the unidirectional growth of organic crystals. Furthermore, using 2,8-difluoro-5,11-bis(triethylsilylethynyl)anthradithiophene (Dif-TES-ADT) as an example, thin films with millimeter-sized single-crystal domains and pure crystallographic orientations are achieved, revealing a significant enhancement (4.7 times) of carrier mobility. More importantly, the resulting film can be directly transferred onto any desired flexible substrates, and flexible transistors based on the Dif-TES-ADT thin films show a mobility as high as 16.1 cm 2 V -1 s -1 , which represents the highest mobility value for the flexible transistors reported thus far. The method is general for the growth of various high-quality OSC thin films, thus opening up opportunities for high-performance organic flexible electronics.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Degradation mechanism of lead-vanado-iodoapatite in NaCl solution

Degradation mechanism of lead-vanado-iodoapatite (IAPT) in NaCl solution at 90 °C was investigated through systematic characterization of surface morphology, microstructure and microchemistry evolution of the alteration layer. Nano-scale characterization indicated that IAPT crystals degraded from grain boundaries toward inner grains, forming ultrafine Cl-bearing crystallites. A coupled interface dissolution-reprecipitation replacement mechanism and the ion exchange between Cl - and I - across the degradation zone may together play roles in determining the nano-scale degradation behavior of IAPT. This work highlights the degradation through multiple reactions and elemental transport across the liquid-solid and solid-solid interfaces at length scales from sub-millimeter to nanoscale.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2020

Phase field modeling of discontinuous dynamic recrystallization in hot deformation of magnesium alloys

We have developed a quantitative phase field model of discontinuous dynamic recrystallization (PF-DDRX) for investigating grain structure evolution and its impact on mechanical response in magnesium alloy during hot deformation. A set of isothermal compression tests were conducted by Gleeble thermo-mechanical simulator and used to determine PF-DDRX model parameters such as critical stresses of recrystallization, activation energies of dislocation, grain boundaries and recrystallization grain nucleation. In the simulations, the experimentally measured average grain size and distribution were used to generate initial microstructures. The results show that the typical ‘necklace’ microstructures observed in DDRX forms at the earlier stage of recrystallization. The inhomogeneity of microstructures first increases rapidly and then decreases gradually and reaches a constant with the increase of dynamic recrystallization volume fraction. Both predicted grain structure and mechanical response are in good agreement with experimental results. This demonstrates that the model parameters determined by experimental data are reliable for the developed PF-DDRX model to predict the grain structure evolution and flow behavior of AZ80 magnesium alloy under hot deformation. This work presents a path to combine experiments and modeling to give quantitative prediction and minimize experimental cost.

magnesium alloy, Phase field method, dynamic recry↗

DOE OSTI2022

Diffusional lithium trapping as a failure mechanism of aluminum foil anodes in lithium-ion batteries

Aluminum foils are an appealing anode for lithium-ion batteries due to high capacity and low-cost, but their viability has been limited due to poor cyclability arising from pulverization and solid-electrolyte interphase growth. Here, we show that significant capacity degradation of aluminum foil anodes during electrochemical cycling also occurs due to diffusional lithium trapping. Scanning electron microscopy of cross-sectioned, cycled foils in the delithiated state reveals large regions of β-LiAl that are passivated by a surface layer of α-Al, which has poor Li + diffusivity. It is found that lithium diffusion occurs preferentially along the β-LiAl grain boundaries, so the grain structure after initial lithiation significantly affects the trapping behavior. Diffusional lithium trapping is exacerbated by both higher delithiation rates and higher areal capacity, presenting a challenge towards commercialization of aluminum foil anodes. We further demonstrate that diffusional trapping in aluminum foil anodes can be mitigated through alloy design, with the addition of 2–3 wt% Li yielding improved first cycle efficiency, and the addition of 1 wt% Si yielding improved cycle life. These results provide a mechanistic understanding of diffusional lithium trapping in aluminum foil anodes and highlight compositional design of alloys as a promising strategy to overcome it.

25 ENERGY STORAGE↗

DOE OSTI2021

In-Situ Ion Irradiation to Add Irradiation Assisted Grain Growth to the Marmot Tool

In the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, the MARMOT mesoscale fuel performance tool is used to inform the development of mechanistic materials models for the BISON fuel performance tool. The grain size of the fuel has a large impact on its performance, directly impacting heat conduction, fission gas release, creep, and fracture. Thus, atomistic and mesoscale MARMOT simulations have been used to investigate grain boundary migration and grain growth in UO 2 . However, the current grain growth models in MARMOT does not consider the effect of irradiation on causing grain growth. This research project experimentally studied and implemented irradiation effects on grain growth of UO 2 into MARMOT.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

NASA NTRS1978

The effect of microstructure on hydrogen embrittlement of the nickel-base superalloy, Udimet 700

Material from a single heat of cast and wrought Udimet 700 was processed and/or heat treated to produce five material conditions with identical chemical compositions but with distinct microstructural variations, and then evaluated for susceptibility to hydrogen embrittlement. Two prealloyed powder conditions exhibited significantly improved resistance to hydrogen embrittlement, as compared to wrought material. No degradation in notch or smooth tensile strengths occurred, and average ductilities of 25 percent reduction of area were determined for 2 hydrogen evaluation procedures. For the most severe hydrogenation procedure, ductility levels were reduced to 15 percent. These improvements were attributed to cleaner grain boundaries and decreases grain size.

Gray, H. R.↗

NASA NTRS1977

Effect of microstructure on Na/+/ diffusion in beta alumina

The effect of microstructural features, such as grain size and orientation, on sodium ion diffusion in polycrystalline beta alumina is investigated; the ionic solid is suitable for use in high-energy and power density batteries. Two types of hot-pressed polycrystalline samples are studied, one with grains highly oriented in the direction normal to the pressing direction, the other with significantly less preferred orientation normal to the pressing direction. Results of the experimental assessments indicate that grain size and diffusion path tortuosity have little effect on diffusion kinetics, while grain boundary type and grain aspect ratio are important factors in determining the diffusion rate.

Sarian, S.↗

NASA NTRS1978

The effect of microstructure on hydrogen embrittlement of the nickel base superalloy, Udimet 700

Gray, H. R.↗

NASA NTRS1980

Automated array assembly task development of low-cost polysilicon solar cells

Development of low cost, large area polysilicon solar cells was conducted in this program. Three types of polysilicon materialk were investigated. A theoretical and experimenal comparison between single crystal silicon and polysilicon solar cell efficiency was performed. Significant electrical performance differences were observed between types of wafer material, i.e. fine grain and coarse grain polysilicon and single crystal silicon. Efficiency degradation due to grain boundaries in fin grain and coarse grain polysilicon was shown to be small. It was demonstrated that 10 percent efficient polysilicon solar cells can be produced with spray on n+ dopants. This result fulfills an important goal of this project, which is the production of batch quantity of 10 percent efficient polysilicon solar cells.

Jones, G. T.↗

NASA NTRS1984

Analysis techniques for tracer studies of oxidation

Analysis techniques to obtain quantitative diffusion data from tracer concentration profiles were developed. Mass balance ideas were applied to determine the mechanism of oxide growth and to separate the fraction of inward and outward growth of oxide scales. The process of inward oxygen diffusion with exchange was theoretically modelled and the effect of lattice diffusivity, grain boundary diffusivity and grain size on the tracer concentration profile was studied. The development of the tracer concentration profile in a growing oxide scale was simulated. The double oxidation technique was applied to a FeCrAl-Zr alloy using 0-18 as a tracer. SIMS was used to obtain the tracer concentration profile. The formation of lacey oxide on the alloy was discussed. Careful consideration was given to the quality of data required to obtain quantitative information.

Basu, S. N.↗

NASA NTRS1984

Creep of chemically vapor deposited SiC fibers

The creep, thermal expansion, and elastic modulus properties for chemically vapor deposited SiC fibers were measured between 1000 and 1500 C. Creep strain was observed to increase logarithmically with time, monotonically with temperature, and linearly with tensile stress up to 600 MPa. The controlling activation energy was 480 + or - 20 kJ/mole. Thermal pretreatments near 1200 and 1450 C were found to significantly reduce fiber creep. These results coupled with creep recovery observations indicate that below 1400 C fiber creep is anelastic with neglible plastic component. This allowed a simple predictive method to be developed for describing fiber total deformation as a function of time, temperature, and stress. Mechanistic analysis of the property data suggests that fiber creep is the result of beta-SiC grain boundary sliding controlled by a small percent of free silicon in the grain boundaries.

Dicarlo, J. A.↗

NASA NTRS1986

Creep of chemically vapour deposited SiC fibres

The creep, thermal expansion, and elastic modulus properties for chemically vapor deposited SiC fibers were measured between 1000 and 1500 C. Creep strain was observed to increase logarithmically with time, monotonically with temperature, and linearly with tensile stress up to 600 MPa. The controlling activation energy was 480 + or - 20 kJ/mole. Thermal pretreatments near 1200 and 1450 C were found to significantly reduce fiber creep. These results coupled with creep recovery observations indicate that below 1400 C fiber creep is anelastic with negligible plastic component. This allowed a simple predictive method to be developed for describing fiber total deformation as a function of time, temperature, and stress. Mechanistic analysis of the property data suggests that fiber creep is the result of beta-SiC grain boundary sliding controlled by a small percent of free silicon in the grain boundaries.

Dicarlo, J. A.↗

DOE OSTI2024

Multi-scale modeling of fuel fragmentation and microstructural evolution

An overview of NEAMS program activities to model fuel fragmentation and microstructual evolution to a group of industry attendees at a meeting hosted by EPRI. Topics include atomistic methods to determine grain boundary strength, phase-field fracture modeling to determine critical pressure at grain boundaries, and coupled phase-field-cluster dynamics to model microstructural evolution.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

DOE OSTI2024

Extended defects-enhanced oxygen diffusion in ThO 2

Oxygen self-diffusion is key to understanding stoichiometry and defect structures in oxide nuclear fuels. Experimentally, low activation-barrier oxygen migration was found in ThO 2 , a candidate nuclear fuel, possibly due to short-circuit diffusion mechanisms. Here, we perform extensive molecular dynamics simulations to show that various types of extended defects can enhance oxygen self-diffusion with a much-reduced activation barrier in ThO 2 . In this work, we consider extended defects including 1D (dislocation), 2D (grain boundary), and 3D (void) defects. Due to the distinct characteristics of each type of extended defect, the modulation of oxygen diffusion varies. Further, these results provide a quantitative description of oxygen transport, which is significantly enhanced within a close distance (nanometer scale) from the extended defects. Among all these considered defects, grain boundary, particularly the low-energy $Σ$3 twin boundary, exhibits the strongest effect on increasing oxygen transport.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2024

Dislocation channel broadening–A new mechanism to improve irradiation-assisted stress corrosion cracking resistance of additively manufactured 316 L stainless steel

Additively manufactured (AM) 316 L stainless steel (SS) after hot isostatic pressing (HIP) was found to exhibit superior resistance to irradiation-assisted stress corrosion cracking (IASCC) in high-temperature water, as compared to wrought 316 L SS. The well-accepted IASCC factors of radiation-induced segregation (RIS) and radiation hardening are not accurate descriptions of IASCC susceptibility in this case. A decreased strain localization along grain boundaries, caused by dislocation channel broadening, was confirmed to suppress crack initiation. A unique distribution of irradiation-induced defects in HIP AM 316 L SS eased dislocation cross-slip compared to those in the wrought counterpart, thus increasing the channel width near the grain boundaries. Here for the first time, this study highlights the importance of dislocation channel broadening as a potential mechanism to further improve the IASCC resistance of 316 L SS and provides direct experimental evidence based on commercial-grade materials.

316L stainless steel↗

NASA NTRS1994

Orthopyroxene as a recorder of primitive achondrite petrogenesis: Major-, minor-, and trace-element systematics of orthopyroxene in Lodran

Considerable attention has been paid recently to the primitive achondrites because they may form a link between chondrites and more differentiated achondrite meteorites. A recent paper by Miyamoto and Takeda addresses the thermal history of lodranites Yamato 74357 and MAC 88177 as inferred from chemical zoning of pyroxene and olivine determined by electron microprobe analyses. Their results suggested that interstitial melt was present and then extracted. We have taken the analysis of Lodran-type meteorites one step further by incorporating the techniques of Electromagnetic Pulse/Wavelength Dispersive Spectroscopy (EMP/WDS) compositional imaging and scanning ion mass spectroscopy (SIMS) analysis. Orthopyroxene in Lodran is strongly zoned in CaO, Al2O3, TiO2, and Cr2O3 within the last 10-30 microns from the grain boundaries. The rims are reversely zoned in Mg-Fe, exhibiting Mg enrichment, and compositions change from a fairly uniform Wo3En94 within the grains to Wo1En96 at the rims. CaO drops from 1.6 to 0.6 wt% and Al2O3, TiO2, and Cr2O3 exhibit similar depletions. MnO is fairly uniform throughout the grains at around 0.5 wt%. Olivine is also reversely zoned with respect to not only grain boundaries but also to fractures within the grains, giving many olivine grains a complex, patchy zoning pattern. Some of the core-rim trace-element systematics for orthopyroxene are illustrated. Because of the rather narrow zoned rims in Lodran orthopyroxene and the low trace-element abundances, it is difficult to clearly resolve the trace-element systematics. Nevertheless it is evident that the cores are enriched in the incompatible trace elements Ce, Nd, Dy, Er, Yb, Y, and Zr relative to the rims.

Papike, J. J.↗

DOE OSTI2020

A Potts Model parameter study of particle size, Monte Carlo temperature, and “Particle-Assisted Abnormal Grain Growth”

A Potts Model was proposed to account for temperature and particle heterogeneity-dependent Zener Pinning. This was accomplished by relating the random fluctuations of grain boundary position allowed by the Potts Model switching probability at finite simulation temperature to experimentally observed grain growth stagnation behavior. We assume that these fluctuations arise from random fluctuations in the thermodynamic and kinetic properties of the grain boundaries and/or interfaces as they change with temperature. As an application of this model, the grain growth kinetics of U-10 wt. % Mo nuclear fuels were simulated with the input of microstructural images during different heat treatment processes. Simulated average grain growth behavior is in good agreement with experiments.

Frazier, William E.↗