Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Feedstock Analysis”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Development of a Surface Water Transportation System for ISRU Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. Initial analysis assumptions allow for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Mars surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This paper describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer water across the Martian surface from a source point to an in-situ resource utilization (ISRU) plant that would use this water as a feedstock to generate oxygen and methane to enable launch of the MAV. Design considerations, concept of operations, and rover energetics will be discussed in this paper.

Fluid Structure Interface↗
NASA NTRSDate not supplied

Assessment of a Surface Water Transportation System for ISRU Operations on Mars

NASA is working to define the architecture needed for a Mars exploration campaign. Initial analysis assumptions allow for pre-deployment of essential cargo and equipment to support a crew landing, including the pre-positioning of a Mars Ascent Vehicle (MAV). This MAV is likely to represent the largest single payload that must be landed on the Mars surface. Its size would be influenced by the amount of mass that state-of-the-art Entry, Descent, and Landing (EDL) systems would be capable of placing on Mars. One possible method of increasing the usable size of the MAV without exceeding available EDL capabilities is to land the MAV without ascent propellant on board. Following such a method may necessitate a strategy to acquire sufficient ascent propellant to allow a crew to safely depart the Martian surface. This paper describes a conceptual return propellant strategy that uses a liquid transportation skid, or pallet, to be used in conjunction with a rover mobility system to transfer water across the Martian surface from a source point to an in-situ resource utilization (ISRU) plant that would use this water as a feedstock to generate oxygen and methane to enable launch of the MAV. Design considerations, concept of operations, and rover energetics will be discussed in this paper.

Fluid Structure Interface↗
DOE OSTI2025

Carbon-conserving bioproduction of malate in an E. coli -based cell-free system

Formate, a biologically accessible form of CO 2 , has attracted interest as a renewable feedstock for bioproduction. However, approaches are needed to investigate efficient routes for biological formate assimilation due to its toxicity and limited utilization by microorganisms. Cell-free systems hold promise due to their potential for efficient use of carbon and energy sources and compatibility with diverse feedstocks. However, bioproduction using purified cell-free systems is limited by costly enzyme purification, whereas lysate-based systems must overcome loss of flux to background reactions in the cell extract. Here, we engineer an E. coli-based system for an eight-enzyme pathway from DNA and incorporate strategies to regenerate cofactors and minimize loss of flux through background reactions. We produce the industrial di-acid malate from glycine, bicarbonate, and formate by engineering the carbon-conserving reductive TCA and formate assimilation pathways. We show that in situ regeneration of NADH drives metabolic flux towards malate, improving titer by 15-fold. Background reactions can also be reduced 6-fold by diluting the lysate following expression and introducing chemical inhibitors of competing reactions. Together, these results establish a carbon-conserving, lysate-based cell-free platform for malate production, producing 64 μM malate after 8 h. This system conserves 43 % of carbon otherwise lost as CO 2 through the TCA cycle and incorporates 0.13 mol CO 2 equivalents/mol glycine fed. Finally, techno-economic analysis of cell-free malate production from formate revealed that the high cost of lysate is a key challenge to the economic feasibility of the process, even assuming efficient cofactor recycling. This work demonstrates the capabilities of cell-free expression systems for both the prototyping of carbon-conserving pathways and the sustainable bioproduction of platform chemicals.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

Extraction Kinetics of Rare Earth Elements from Ion-Adsorbed Underclays

Citric acid has been identified as an environmentally sustainable organic acid capable of leaching up to ~30% of easily accessible REEs from underclay material. An analysis of the leaching profiles was performed to discern the reaction rates, extraction efficiencies, and potential leaching mechanisms of REEs and cations of interest from ion-adsorbed underclays. The initial leaching stage follows a slow intraparticle diffusion mechanism followed by a second stage controlled by a mixed diffusion regime. The leaching profiles of Ca and P were similar to those of REEs, suggesting that REEs are most likely derived from mineral surfaces such as hydroxyapatite or crandallite rather than predominately from underclays. Fitting to a modified diffusion control model found diffusion-controlled leaching to be the primary mechanism whereas non-diffusive mechanisms made up about 22% of the extracted REEs. Gangue cations associated with underclays had less non-diffusive leaching than REE species, indicating that their leaching kinetics may be dominated by diffusion from within the material or potentially from product layer formation. Fitting to Boyd plots further indicated that REEs were leached following intraparticle diffusion control. These results have important implications for the development of more efficient and sustainable methods for extracting REEs or critical minerals from alternative feedstocks.

Prem, Priscilla↗
DOE OSTI2021

Biofuel Options for Marine Applications: Technoeconomic and Life-Cycle Analyses

This study performed technoeconomic and life-cycle analyses to assess the economic feasibility and emission benefits and tradeoffs of various biofuel production pathways as an alternative to conventional marine fuels. We analyzed production pathways for (1) Fischer-Tropsch diesel from biomass and cofeeding biomass with natural gas or coal, (2) renewable diesel via hydroprocessed esters and fatty acids from yellow grease and cofeeding yellow grease with heavy oil, and (3) bio-oil via fast pyrolysis of low-ash woody feedstock. We also developed a new version of the Greenhouse gases, Regulated Emissions, and Energy use in Transportation (GREET) marine fuel module for the estimation of life-cycle greenhouse gas (GHG) and criteria air pollutant (CAP) emissions of conventional and biobased marine fuels. The alternative fuels considered have a minimum fuel selling price between 2.36 and 4.58 $/heavy fuel oil gallon equivalent (HFOGE), and all exhibit improved life-cycle GHG emissions compared to heavy fuel oil (HFO), with reductions ranging from 40 to 93%. The alternative fuels also exhibit reductions in sulfur oxides and particulate matter emissions. Additionally, when compared with marine gas oil and liquified natural gas, they perform favorably across most emission categories except for cases where carbon and sulfur emissions are increased by the cofed fossil feedstocks. The pyrolysis bio-oil offers the most promising marginal CO2 abatement cost at less than $100/tonne CO2e for HFO prices >$1.09/HFOGE followed by Fischer-Tropsch diesel from biomass and natural gas pathways, which fall below $100/tonne CO2e for HFO prices >$2.25/HFOGE. Pathways that cofeed fossil feedstocks with biomass do not perform as well for marginal CO2 abatement cost, particularly at low HFO prices. This study indicates that biofuels could be a cost-effective means of reducing GHG, sulfur oxide, and particulate matter emissions from the maritime shipping industry and that cofeeding biomass with natural gas could be a practical approach to smooth a transition to biofuels by reducing alternative fuel costs while still lowering GHG emissions, although marginal CO2 abatement costs are less favorable for the fossil cofeed pathways.

Greenhouse gas, life cycle assessment, techno-econ↗
DOE OSTI2021

Redefining marginal land for bioenergy crop production

Abstract Marginal land has received wide attention for its potential to produce bioenergy feedstocks while minimizing diversion of productive agricultural land from food crop production. However, there has been no consensus in the literature on how to define or identify land that is marginal for food crops and beneficial for bioenergy crops. Studies have used different definitions to quantify the amount of such land available; these have largely been based on assumed biophysical thresholds for soil quality and productivity that are unchanging over space and time. We discuss the limitations of these definitions and the rationale for considering economic returns and environmental outcomes in classifying land as marginal. We then propose the concept of “socially” marginal which is defined as land that is earning close to zero returns after accounting for the monetized costs of environmental externalities generated. We discuss a broad set of criteria for classifying land as socially marginal for food crops and suitable for bioenergy crops; with these criteria, this classification depends on spatially varying and time‐varying factors, such as climate and market conditions and policy incentives. While there are challenges related to identifying this marginal land, satellite and other large‐scale datasets increasingly enable such analysis at a fine spatial resolution. We also discuss reasons why landowners might choose not to convert bioenergy‐suitable land to bioenergy crops, and thus the need for policy incentives to support conversion of land that is socially beneficial for bioenergy crop production.

09 BIOMASS FUELS↗
DOE OSTI2020

Development of a Genome-Scale Metabolic Model of Clostridium thermocellum and Its Applications for Integration of Multi-Omics Datasets and Computational Strain Design

Solving environmental and social challenges such as climate change requires a shift from our current non-renewable manufacturing model to a sustainable bioeconomy. To lower carbon emissions in the production of fuels and chemicals, plant biomass feedstocks can replace petroleum using microorganisms as biocatalysts. The anaerobic thermophile Clostridium thermocellum is a promising bacterium for bioconversion due to its capability to efficiently degrade lignocellulosic biomass. However, the complex metabolism of C. thermocellum is not fully understood, hindering metabolic engineering to achieve high titers, rates, and yields of targeted molecules. In this study, we developed an updated genome-scale metabolic model of C. thermocellum that accounts for recent metabolic findings, has improved prediction accuracy, and is standard-conformant to ensure easy reproducibility. We illustrated two applications of the developed model. We first formulated a multi-omics integration protocol and used it to understand redox metabolism and potential bottlenecks in biofuel (e.g., ethanol) production in C. thermocellum. Second, we used the metabolic model to design modular cells for efficient production of alcohols and esters with broad applications as flavors, fragrances, solvents, and fuels. The proposed designs not only feature intuitive push-and-pull metabolic engineering strategies, but also present novel manipulations around important central metabolic branch-points. We anticipate the developed genome-scale metabolic model will provide a useful tool for system analysis of C. thermocellum metabolism to fundamentally understand its physiology and guide metabolic engineering strategies to rapidly generate modular production strains for effective biosynthesis of biofuels and biochemicals from lignocellulosic biomass.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Design and optimization of processes for recovering rare earth elements from end‐of‐life permanent magnets

Recovery of rare earth elements (REEs) from end-of-life (EOL) products represents a strategic opportunity to strengthen the domestic supply chain for rare earth elements. This work presents a superstructure-based optimization framework for finding the most economical processing pathway for different EOL rare earth permanent magnets (REPMs). The framework evaluates state-of-the-art technologies across four processing stages—disassembly, demagnetization, leaching and extraction, and precipitation and calcination—using net present value (NPV) maximization and cost of recovery (COR) minimization objectives. A novel bottom-up costing framework for hydrogen decrepitation is also introduced. Two feedstocks were considered: REPMs from EOL hard disk drives (HDDs), and electric and hybrid electric vehicles (EVs and HEVs). While HDD recycling proved unprofitable due to limited feedstock availability, EVs/HEVs were profitable across a range of parameters and cost estimates. Therefore, our findings suggest that the proposed EOL EV/HEV recycling process may be economical and is worthy of further investigation.

29 ENERGY PLANNING, POLICY, AND ECONOMY↗
DOE OSTI2022

Biomass formation and sugar release efficiency of Populus modified by altered expression of a NAC transcription factor

Woody biomass is an important feedstock for biofuel production. Manipulation of wood properties that enable efficient conversion of biomass to biofuel reduces cost of biofuel production. Wood cell wall composition is regulated at several levels that involve expression of transcription factors such as wood-/secondary cell wall-associated NAC domains (WND or SND). In Arabidopsis thaliana, SND1 regulates cell wall composition through activation of its down-stream targets such as MYBs. The functional aspects of SND1 homologs in the woody Populus have been studied through transgenic manipulation. In this study, we investigated the role of PdWND1B, Populus SND1 sequence ortholog, in wood formation using transgenic manipulation through over-expression or silencing under the control of a vascular-specific 4-coumarate-CoA ligase (4CL) promoter. As compared with control plants, PdWND1B-RNAi plants were shorter in height, with significantly reduced stem diameter and dry biomass, whereas there were no significant differences in growth and productivity of PdWND1B over-expression plants. Conversely, PdWND1B over-expression lines showed a significant reduction in cellulose and increase in lignin content, whereas there was no significant impact on lignin content of downregulated lines. Stem carbohydrate composition analysis revealed a decrease in glucose, mannose, arabinose, and galactose, but an increase in xylose in the over-expression lines. Transcriptome analysis revealed upregulation of several downstream transcription factors and secondary cell wall related structural genes in the PdWND1B over-expression lines, partly explaining the observed phenotypic changes in cell wall chemistry. Relative to the control, glucose release efficiency and ethanol production from stem biomass was significantly reduced in over-expression lines. Our results show that PdWND1B is an important factor determining biomass productivity, cell wall chemistry and its conversion to biofuels in Populus.

09 BIOMASS FUELS↗
DOE OSTI2020

An experimental investigation of the effectiveness of Ar-CO 2 shielding gas mixture for the wire arc additive process

Wire arc additive manufacturing (AM) is the process by which a large, metallic structure is built layer-by-layer using a welding arc to melt a wire feedstock. A novel opportunity exists to alter the shielding gas composition to fabricate distinct geometrical features without altering the other AM parameters. In this paper, shielding gases with varied concentrations of Argon (Ar) and CO 2 was used to deposit three distinct geometric shapes (walls, infill, and overhang) using a wire-based additive manufacturing system utilizing the gas metal arc welding (GMAW) surface tension transfer (STT) process. Computer-aided design (CAD) models were sliced with a custom-built slicer, and the sliced algorithm was converted into optimal robotic toolpaths. A custom virtual instrument (VI) was built in LabVIEW to compare the temperature profiles on the surface during each deposition process. After each deposition, the geometric features were scanned, and the surface waviness value was evaluated. Tensile and Charpy impact coupons were extracted from the wall geometries in the longitudinal and transverse directions and tested. The results indicated that a higher CO 2 content produced higher melt pool temperatures to an extent, while lower contents of CO 2 resulted in a dimensionally accurate geometry. The data also indicated that the 2%/98% CO 2 /Ar blend produced scatter in tensile strength and the analysis of variance (ANOVA) shows significant difference. However, the intermediate range of CO 2 (5–10%) resulted in uniform tensile properties. Altogether, these results indicate that a 5%/95% CO 2 /Ar blend is the ideal shielding gas for lowering process temperatures and improving mechanical properties in wire arc additive manufacturing using the gas metal arc welding surface tension transfer process. Additionally, varying concentrations of Ar/CO 2 can be used within the same part in order to modify the local properties or process parameters such as strength, toughness, temperature, or dimensional features. This may improve overall manufacturing quality without sacrificing specific properties.

42 ENGINEERING↗
DOE OSTI2024

Manuscript Workflows from and Processed Organic Matter Composition of Experimentally Burned Open Air and Muffle Furnace Vegetation Chars across Differing Burn Severity and Feedstock Types from Pacific Northwest, USA (v3)

This dataset includes processed organic matter chemistry data from an experimental study designed to compare how the chemical composition of organic matter changes across different burn conditions and vegetation materials representative of major land cover types of the Pacific Northwest, USA. Chars were created in a closed muffle furnace or on an open burn table from four different feedstock species representing vegetation commonly impacted by fire regimes across the Pacific Northwest, USA. Source data and associated metadata (including methods and geospatial information) can be found at https://data.ess-dive.lbl.gov/datasets/doi:10.15485/1894135 (Grieger et al. 2022). This dataset provides processing scripts and processed data for both solid and dissolved phase organic matter characterization data from experimentally generated chars. These processed data can be used to compare how different burn conditions may influence resultant organic matter chemistry and help further our understanding of potential biogeochemical impacts on river corridors post-fire. The processed data were subsequently analyzed; and the results and ecological implications of the findings were published in peer-reviewed manuscripts. The scripts and workflows used to develop the manuscripts are also included in this data package.This data package was originally published June 2024. It was updated September 2024 (new and modified files) and in January 2025 (modified files). See the change history section in the readme for more details.This dataset is comprised of one data package readme, one data dictionary (dd), one file level metadata (flmd), and folders containing (A) processed data; (B) general processing scripts; and (C) additional folders with specific manuscript analysis scripts and processed data. Step-by-step instructions to assist the user in recreating the workflow used to generate the results in the manuscripts is also provided. The processed data folder includes (1) a folder of processed Parallel Factor Analysis (PARAFAC) and spectra indices outputs from excitation emissions matrix (EEM) fluorescence and absorbance data; (2) a folder of processed solid state carbon-13 (13-C NMR) integrals; (3) folder of high resolution characterization of organic matter via 21 Tesla Fourier transform ion cyclotron resonance mass spectrometry (FTICR-MS) generated through the Environmental Molecular Sciences Laboratory (EMSL; https://www.pnnl.gov/environmental-molecular-sciences-laboratory) processed data outputs from Formultitude (https://github.com/PNNL-Comp-Mass-Spec/Formultitude), blank corrections and data aggregation, and calculated molecular indices. All files are .pdf, .csv, .html, .Rmd, .R, or .RData.

54 ENVIRONMENTAL SCIENCES↗
DOE OSTI2020

Silencing Folylpolyglutamate Synthetase1 (FPGS1) in Switchgrass (Panicum virgatum L.) Improves Lignocellulosic Biofuel Production

Switchgrass (Panicum virgatum L.) is a lignocellulosic perennial grass with great potential in bioenergy field. Lignocellulosic bioenergy crops are mostly resistant to cell wall deconstruction, and therefore yield suboptimal levels of biofuel. The one-carbon pathway (also known as C1 metabolism) is critical for polymer methylation, including that of lignin and hemicelluloses in cell walls. Folylpolyglutamate synthetase (FPGS) catalyzes a biochemical reaction that leads to the formation of folylpolyglutamate, an important cofactor for many enzymes in the C1 pathway. In this study, the putatively novel switchgrass PvFPGS1 gene was identified and its functional role in cell wall composition and biofuel production was examined by RNAi knockdown analysis. The PvFPGS1-downregulated plants were analyzed in the field over three growing seasons. Transgenic plants with the highest reduction in PvFPGS1 expression grew slower and produced lower end-of-season biomass. Transgenic plants with low-to-moderate reduction in PvFPGS1 transcript levels produced equivalent biomass as controls. There were no significant differences observed for lignin content and syringyl/guaiacyl lignin monomer ratio in the low-to-moderately reduced PvFPGS1 transgenic lines compared with the controls. Similarly, sugar release efficiency was also not significantly different in these transgenic lines compared with the control lines. However, transgenic plants produced up to 18% more ethanol while maintaining congruent growth and biomass as non-transgenic controls. Severity of rust disease among transgenic and control lines were not different during the time course of the field experiments. Altogether, the unchanged lignin content and composition in the low-to-moderate PvFPGS1-downregulated lines may suggest that partial downregulation of PvFPGS1 expression did not impact lignin biosynthesis in switchgrass. In conclusion, the manipulation of PvFPGS1 expression in bioenergy crops may be useful to increase biofuel potential with no growth penalty or increased susceptibility to rust in feedstock.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2026

Metabolomics analysis of P. tremula × P. alba ‘717-1B4’ tissue culture hybrids grown in liquid media supplemented with EGGC and d4-EGGC

A metabolite linked to ethylene metabolism in Populus was recently structurally characterized as 2-hydroxyethyl β-D-glucopyranoside, an ethylene glycol glucose conjugate (EGGC). The dataset presented here is associated with the metabolomics analysis of various tissues (i.e., roots, stems/leaves) of plants grown in liquid media supplemented with EGGC and stable-isotope labelled EGGC (i.e., d4-EGGC). Data were collected using a Thermo Scientific gas chromatograph (GC) coupled to a Q Exactive Orbitrap mass spectrometer (MS). Samples were collected at three different timepoints and silylated prior to GCMS analysis.

09 BIOMASS FUELS↗
DOE OSTI2023

SPERLU Selective Process for Efficient Removal of Lignin and Upgrading (Final Technical Report)

To meet the growing demand for bio-based chemicals and improve the profitability and efficiency of the emerging biorefinery industry, lignin is an abundant and attractive feedstock. Spero Renewables has developed a proprietary and patent-pending technology, the Selective Process for Efficient Removal of Lignin and Upgrading (SPERLU). The technology is a catalytic deconstruction and upgrading of lignin in lignocellulosic biomass or commercially available technical lignin to produce multi-functional phenol (MFP) products. The SPERLU process has been demonstrated and vetted on a lab scale to convert commercially available technical lignin to MFPs in yields of 60-90% (based on lignin). The MFP products can be separated and further upgraded through catalytic or biological means. Spero performed a detailed kinetic study of the SPERLU process and used the resulting kinetic data to design and construct a mini-pilot-scale reactor for routine production of hundreds of grams of MFP products. Spero’s lignin-based MFPs have been demonstrated for use as a drop-in replacement for bisphenol A (BPA) in the synthesis of thermoset polymers. Spero’s lignin-based thermoset polymers exhibit excellent mechanical properties and can be used in many applications. Additionally, a collaboration with the National Renewable Energy Lab (NREL) was used to evaluate the feasibility of upgrading SPERLU products through biological means into valuable chemicals. A comprehensive technoeconomic analysis (TEA) and Life-cycle analysis (LCA) have been completed and support the case for commercialization of the SPERLU technology. Through this project Spero has significantly de-risked the SPERLU technology and is actively planning larger scale pilot projects.

09 BIOMASS FUELS↗
DOE OSTI2025

Bleach Rescues Nannochloropsis from an Obligate Parasite and Alters Microbial and Metabolite Signatures of Outdoor Cultures

Chemical agents are commonly used to protect algal crops. Yet, few studies have characterized the effects of these agents on associated microbial communities to understand effects on microbial functions relevant to algal crop production and protection. Here, we used shotgun metagenomic sequencing and untargeted exometabolite profiling to link the application of bleach, a -cidal agent used to protect algae from pests, to changes in community composition, metabolic pathways, and exometabolies - at a whole community level. Bleach protected the algal crop from crashing but altered bacterial diversity. Analysis of metagenome-assembled genomes (MAGs) revealed a classic predator-prey cycle between Oligoflexus and our target alga Nannochloropsis. Olifoflexus genomes from our study were notably similar to a previously identified BALO (Bdellovibrio and like organism), FD111, known to kill Nannochloropsis cultures, providing strong evidence that an FD111-like organism was responsible for the crash. Metabolic pathway composition differed between bleached and unbleached ponds, with abundance of twelve pathways related to stress tolerance, including the superpathway of methylglyoxal degradation, lipid IVA biosynthesis, and ectoine biosynthesis, greater in bleached ponds compared to unbleached ponds. Virulence factors related to adherence, biofilm formation, motility, and pathogenicity increased dramatically in bleached ponds with time, although this increase was not coupled with an increase in pathogens - algal or otherwise - or a decline in algal health. Our study highlights the importance of coupling 16S rRNA gene sequencing with whole genome data and other -omics tools to sketch a larger picture of community structure and function in crop systems. Moreover, our results highlight that continued long-term bleaching may lead to negative effects to crop health or downstream adverse health effects to humans or animals, depending on the algal product (i.e. human supplements or animal feedstocks). Future work on alternative treatment methods that would reduce resistance is necessary in the field.

09 BIOMASS FUELS↗
DOE OSTI2024

Process Intensification for Nanostructure Aluminum Extrusions

A new technology called Shear Assisted Processing and Extrusion (ShAPE™), pioneered at the Pacific Northwest National Laboratory (PNNL), has the potential to revolutionize the US extrusion industry. Maturation of the ShAPE™ process would create a new cross cutting US manufacturing technology that advances three key the objectives within AMO; namely, nanomaterials processing, process intensification, and materials for extreme and harsh environments. PNNL and SCM Metals Products, Inc. (SCM), a division of Kymera International, will collaborate to mature the ShAPE™ extrusion process beyond TRL 3 to increase the likelihood of its adoption by industry. PNNL’s custom (one-of-a-kind in the world) ShAPE™ machine will be used to extrude round rods of high strength aluminum alloy feedstock powder provided by SCM. As proof-of-concept, PNNL has previously extruded 5 mm diameter rods with SCM aluminum alloy powder AL-12.4TM. This project aims to scale up the process to a diameter of 25 mm while retaining the excellent mechanical properties achieved for the 5 mm diameter rods. The degree of process intensification with ShAPE™ will also be estimated. The primary objectives of this project are as follows. 1) Fabricate 25 mm diameter nanostructured extrusions in bulk, directly from AL-12.4TM aluminum alloy powder without the need for canning, degassing, compaction, and other intermediate steps typical of powder metallurgy extrusion. 2) Achieve a microstructure with an ultrafine grained (UFG <1 µm) aluminum matrix having refined and homogenously distributed nanoscale second phases. 3) Show that the ram force can be significantly reduced compared to conventional powder metallurgy extrusion of the same material and estimate the extent of process intensification that may be possible with ShAPE™. 4) Demonstrate improved high-temperature mechanical properties compared to conventional extrusion of the same material. The following tasks will be undertaken to achieve these objectives. PNNL will develop the die set and process parameters necessary to fabricate Al-12.4TM extrusions with a 25 mm diameter. Microstructural analysis will be performed by PNNL while mechanical testing will be conducted by SCM. With information learned from the process development and characterization, PNNL will perform an estimate of the degree of process intensification that may be possible with ShAPE™.

42 ENGINEERING↗