Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Emulator”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Real-time rapid leakage estimation for deep space habitats using exponentially-weighted adaptively-refined search

The recent accelerated growth in space-related research and development activities makes the near-term need for long-term extraterrestrial habitats evident. Such habitats must operate under continuous disruptive conditions arising from extreme environments like meteoroid impacts, extreme temperature fluctuations, galactic cosmic rays, destructive dust, and seismic events. Loss of air or atmospheric leakage from a habitat poses safety challenges that demand proper attention. Such leakage may arise from micro-meteoroid impacts, crack growth, bolt/rivet loosening, and seal deterioration. In this paper, leakage estimation in deep space habitats is posed as an inverse problem. A forward pressure-based dynamical model is formulated for atmospheric leakage. Experiments are performed on a small-scaled pressure chamber where different leakage scenarios are emulated and corresponding pressure values are measured. An exponentially-weighted adaptively-refined search (EWARS) algorithm is developed and validated for the inverse problem of real-time leakage estimation. It is demonstrated that the proposed methodology can achieve real-time estimation and tracking of constant and variable leaks with accuracy.

Deep space habitats↗
NASA NTRSDate not supplied

Observing System Simulations for the AOS Mission

The Earth System Observatory (ESO) is NASA’s response to the recommendations of the 2017 Earth Sciences Decadal Survey conducted by the US National Academy of Sciences, Engineering and Medicine. The ESO is being conceived as a set of fully integrated missions addressing 4 main Earth science focus areas including aerosols, clouds, convection and precipitation (jointly re-ferred to as AOS, the Atmosphere Observing System). ESO ground breaking observations will provide critical measurements to address societally relevant problems in climate change, natural hazard mitiga-tion, fighting forest fires, and improving real-time agricultural processes. A critical element of the AOS observing strategy is to make extensive use of new passive and active sen-sors as well as of the so-called Program-of-Record (PoR), complemented by a fully integrated sub-orbital component. In order to achieve maximum benefit, all these observations need to be integrated into comprehensive observing and modeling/data assimilation systems. Such an approach requires compre-hensive model-data synthesis capabilities that needs to be conceived in conjunction with the space-based and suborbital components of AOS. In this presentation we will summarize the major science goals of AOS including cloud feedbacks, at-mospheric convection, emphasizing aerosol processes and aerosol radiative effects, and the synergistic aspects of clouds-precipitation-aerosol interactions. We will describe examples of the observing system simulation capabilities being developed for AOS, including global storm resolving nature runs, detailed instrument and retrieval simulators, as well as fast retrieval emulators for instrumenting climate models. This simulation environment, being developed under NASA’s open-source science initiative, will permit us to explore how AOS data will be used across space and time to better initialize forecasts and train modeling systems, and to infuse models and data assimilation systems with AOS data, well before launch.

Arlindo da Silva↗
NASA NTRS2022

Velocimeter LIDAR Based Bulk Velocity Estimation for Terrain Relative Navigation Applications

A novel batch state estimation approach to estimate the translational and angular velocity states of a vehicle using a state-of-the-art velocimeter Light Detection and Ranging (LIDAR) sensor for use in Terrain and Hazard Relative Navigation (TRN/HRN) applications is presented in this paper. The velocimeter LIDAR is capable of measuring three dimensional position and line-of-sight (LOS) velocity associated with every pixel in the field-of-view (FOV). This new batch state estimation methodology is shown to provide accurate and statistically consistent velocity estimates with no a priori information. In contrast to traditional computer vision approaches for TRN, the proposed technique is not dependent on image features. This feature alleviates the need for accurate feature detection and correspondence to a predefined map making it suitable for unknown operating environments. Following a detailed development of the mathematical details associated with the batch state estimation methodology, the efficacy and utility of the proposed algorithms are evaluated through emulation robotics experiments performed at Texas A&M’s Land, Air, and Space Robotics (LASR) laboratory.

Skulsky, Eli↗
NASA NTRSDate not supplied

Real-time Hardware-in-the-Loop Evaluation of a Partially Turboelectric Propulsion Control Design

In support of aviation fuel burn and emission reduction goals, NASA is pursuing high-payoff research investments that promise to transform aviation. This includes investments in Electrified Aircraft Propulsion (EAP). Multiple technology challenges must be addressed to unlock the full potential of EAP. This includes addressing challenges related to propulsion controls, which will be vital for ensuring efficient coordinated operation of EAP subsystems. This paper presents results from real-time hardware-in-the-loop testing of a control design for a single aisle partially-turboelectric aircraft propulsion concept conducted at the NASA Electric Aircraft Testbed (NEAT) facility. The control system under test is designed for a propulsion concept consisting of two wing-mounted turbofan engines that produce thrust and generate electrical power to drive a boundary layer ingesting tailfan propulsor via an electrical motor. An integrated control strategy is applied to ensure coordinated operation of the turbofan and tailfan subsystems during steady-state and transient operation throughout the flight envelope. The NEAT test of this integrated control design consists of a partially hardware-in-the-loop, partially simulated configuration. A subscale representation of the electrical system design is implemented in hardware and mechanically coupled to electric machines that emulate turbomachinery and propulsor shaft dynamics. The hardware configuration is then operated under the control of a real-time computer application that runs a simulation of the propulsion system and the developed control logic. The NEAT facility test campaign includes a series of experiments that subject the control design to throttle transients conducted throughout the flight envelope and full-flight mission profiles. Testing under simulated performance degradation is also conducted to evaluate control design robustness. This includes constant and abrupt changes in degradation levels. Results from the hardware-in-the-loop test are presented and shown to be in good agreement with pre-test simulation predictions demonstrating the efficacy of the integrated control design approach.

Electrified Aircraft Propulsion↗
NASA NTRSDate not supplied

Real-time Hardware-in-the-Loop Evaluation of a Partially Turboelectric Propulsion Control Design

In support of aviation fuel burn and emission reduction goals, NASA is pursuing high-payoff research investments that promise to transform aviation. This includes investments in Electrified Aircraft Propulsion (EAP). Multiple technology challenges must be addressed to unlock the full potential of EAP. This includes addressing challenges related to propulsion controls, which will be vital for ensuring efficient coordinated operation of EAP subsystems. This paper presents results from real-time hardware-in-the-loop testing of a control design for a single aisle partially-turboelectric aircraft propulsion concept conducted at the NASA Electric Aircraft Testbed (NEAT) facility. The control system under test is designed for a propulsion concept consisting of two wing-mounted turbofan engines that produce thrust and generate electrical power to drive a boundary layer ingesting tailfan propulsor via an electrical motor. An integrated control strategy is applied to ensure coordinated operation of the turbofan and tailfan subsystems during steady-state and transient operation throughout the flight envelope. The NEAT test of this integrated control design consists of a partially hardware-in-the-loop, partially simulated configuration. A subscale representation of the electrical system design is implemented in hardware and mechanically coupled to electric machines that emulate turbomachinery and propulsor shaft dynamics. The hardware configuration is then operated under the control of a real-time computer application that runs a simulation of the propulsion system and the developed control logic. The NEAT facility test campaign includes a series of experiments that subject the control design to throttle transients conducted throughout the flight envelope and full-flight mission profiles. Testing under simulated performance degradation is also conducted to evaluate control design robustness. This includes constant and abrupt changes in degradation levels. Results from the hardware-in-the-loop test are presented and shown to be in good agreement with pre-test simulation predictions demonstrating the efficacy of the integrated control design approach.

Electrified Aircraft Propulsion↗
NASA NTRSDate not supplied

Comparing the Electrical Modeling and Thermal Analysis Toolbox Simulation Data to Electrified Aircraft Propulsion Test Hardware Data

A model using the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), a National Aeronautics and Space Administration (NASA)-developed Simulink® model block library of electrical components, was developed to mirror the Hybrid Propulsion Emulation Rig (HyPER) hardware, a laboratory focused on Electrified Aircraft Propulsion (EAP) hardware tests. The goal of the model was to demonstrate the utility of the library by comparing the accuracy of the library models to the performance of real hardware, with the primary metrics being the simulation outputs matching physical test hardware data within 5% of full scale.The objective of this paper is to present the background, setup, testing and results of this comparison. It describes some of the adjustments that were necessary to match the system hardware, as well as next steps in verification and validation. The outputs of the model were compared to the results of several tests in HyPER, and in the process captured an additional torque loss that is still being analyzed for the root cause but has been confirmed in the hardware. Across all the test series, only one key model parameter was outside the target 5% full scale matching, and nearly 70% were within 1%.

Mark E Bell↗
NASA NTRSDate not supplied

Comparing the Electrical Modeling and Thermal Analysis Toolbox Simulation Data to Electrified Aircraft Propulsion Test Hardware Data

The Electrical Modeling and Thermal Analysis Toolbox (EMTAT), a National Aeronautics and Space Administration (NASA)-developed Simulink™ model block library of electrical components developed with the goal of facilitating system-level control design and analysis, has two levels of fidelity depending on the test needs. The Physics Based model blocks are designed to use physical component characteristics to more accurately model real hardware, including power losses, efficiency, thermal effects, electromagnetic losses, voltage drops and current requirements. These blocks model electrical dynamics that occur at the millisecond turbomachinery time scale which allows for faster-than-real-time electrified turbomachinery simulations. A model was developed to mirror the Hybrid Propulsion Emulation Rig (HyPER) hardware, a laboratory focused on Electrified Aircraft Propulsion (EAP) hardware tests. The present hardware setup supports Turbine Electrified Energy Management (TEEM) testing. The outputs of the model were compared to the results of several tests on the HyPER laboratory motor-generator setup with the goal of matching the steady state simulation data to steady state hardware data within 5% of full scale. The objective of this paper is to present the background, setup, testing and results of this comparison. It will describe some of the adjustments that were necessary to match the system hardware, as well as next steps in verification and validation.

Hyper↗
NASA NTRS2022

Europa Clipper Payload Verification and Validation: Avionics-Instrument Interface Test Campaign

NASA's Europa Clipper mission will investigate Jupiter's icy moon Europa using a payload suite consisting of nine instruments to address a range of scientific objectives concerning Europa's habitability. As the project proceeds past its Critical Design Review, confidence is being built in the system's ability to achieve mission objectives through the implementation of a rigorous payload verification and validation (V&V) program. As part of this payload V&V program, instrument box-level testing was performed by the payload team to verify select instrument-avionics interface requirements. This testing was performed at JPL using the avionics testbed's Bulk Data Storage Emulator (BDSEM) with visiting instrument Test Models. This paper summarizes the Data Link test campaign involving roughly four days of functional testing per instrument, including planning, testing methods, types of issues found, and the requirement closure process. Detail is also provided on the development, deployment, and validation of a standardized analysis tool used in data reviews. This testing verified requirements related to commanding rates, loss of link, packet format, clock counters, loopback test capability, and SpaceWire jitter and skew margins. Additional risk reduction testing of basic commanding, counter behavior, science data collection and transfer, and interface swapping was also performed. Because the BDSEM venue was not originally designed to be a run for record venue, the process of characterizing venue fidelity and establishing suitability for requirement closure using data collected in this venue will also be addressed.In order to close requirements, an extensible tool was developed to post-process instrument command and telemetry data from their original binary to a human-readable format and give visibility to errors detected within the data, such as packets with Cyclic Redundancy Check errors. This tool, called payload-packet-parser, is a Python 3.9 command line tool built using a variety of open-source Python libraries. Payload-packet-parser was designed to support parsing command and telemetry packets for all Europa Clipper instruments and additional analysis tools were developed for verification of specific information interface requirements. This test campaign, including post-processing using a single parsing and verification toolset, allowed for early interface testing, alleviating testing burdens on instrument teams and buying down risk on the instrument-avionics interface by finding hardware and software issues and idiosyncrasies prior to integration with system test venues. Over twenty issues were discovered across the payload, resulting in software updates and instrument rework well in advance of any system impacts. This paper concludes with an assessment of benefits and costs of this type of testing and lessons learned.

Montanez, Leticia↗
NASA NTRSDate not supplied

Quantifying Leak Rates and Vacuum Impact on Granular Soil Column Pneumatic Seal

Introduction: All In-Situ Resource Utilization (ISRU) regolith reactor systems that aim to extract gases or vapors must maintain a seal along the flow path of the regolith from the inlet hopper to where extracted gases or vapors are generated. Using a column of regolith at the inlet has been proposed as an alternative to systems using series of mechanical valves to reduce mass and complexity. Preliminary investigations into the use of regolith itself as a barrier to escaping fluids have been conducted, which this research seeks to expand upon. Different vertical regolith simulant plug diameters and heights were tested under vacuum with dry nitrogen to observe leak rates and approximate steady state pressure gradient equilibria. The effect of absolute ambient pressure was also studied by repeating tests at incremental pressures ranging from 10e-5 Torr up to 1 atm to corroborate ambient bench tests from previous work. The impact of regolith dynamics was addressed to emulate continuous-feed regolith reaction processes by measuring leak rates through continuously draining simulant columns. OB-1 lunar highlands regolith simulant was used. Experimental Setup: Regolith simulant columns were constructed using a motorized butterfly valve separating upper acrylic tubes of various diameters from a larger, lower aluminum pipe plenum (See Figure 1). The butterfly valve was cracked open such that gas could freely pass through whereas regolith would bridge and stay suspended as a cohesive plug above in the acrylic portion. These assemblies were loaded into a vacuum chamber, and a compressed dry nitrogen line was routed into the lower plenum. Pressure transducers measured the absolute pressure of the lower plenum, which was compared to absolute chamber pressure to monitor the pressure gradient across the regolith simulant. A precision mass flow controller enabled fine control of plenum pressure. The plenum pressure was quasi-statically increased to set points informed by previous work [1] before shutting off the gas supply to allow the now pressurized gas volume to dissipate through the simulant into the chamber in what was referred to as a ‘leak test.’ In a separate set of tests, the pressure was allowed to quasi-statically build until visual disturbances in the soil were observed via remote camera feeds. Initial leak rate tests were repeated on the disturbed soil to observe changes in leak rates between initial as-poured and post-bubbling soil conditions. This test schedule was applied to simulant columns of three different diameters (approximately 2, 4, and 6 inches) as well as two different heights (around 8 and 16 inches) and was repeated at least three times for each configuration. Plenums were also pressurized while the butterfly valves were opened slightly further to facilitate slow, controlled, constant flowrate draining of the simulant to observe the impact that continuous-feed systems might have on leak rate through the regolith column. Finally, the regolith columns were reset and refilled and static leak rate tests were repeated approximately every decade in ambient pressure from 10e-5 Torr up to ambient conditions to observe the impact of transitioning out of the molecular flow regime on regolith column seal performance. Analysis: Trends with respect to each factor examined were constructed and reported alongside commentary on the most likely responsible physical phenomena. Confidence intervals were applied to the predictive findings of the data by quantifying instrumentation error and accounting for probabilistic impacts of curve fitting the generic exponential function onto pressure decay data. The leak rate is assumed directly proportional to the exponential term coefficient, while the steady-state static pressure gradient is assumed to be the asymptotic limit of each curve fit. Finally, a generic model developed by Ogino et al. [2] and later tuned for ambient testing was re-tuned using vacuum data to estimate leak rates on the lunar surface. Results: Pressure decay rates decreased up to 27-fold under vacuum when compared to ambient pressure, as shown in Figure 2. Simulant column diameter was found to exponentially correlate to both regolith column leak rate and steady-state equilibrium pressure delta. Height was found to be linearly related to leak rate –doubling the regolith column height consistently yielded around a 40% reduction in leak rate. Dynamic regolith draining was found to slightly increase leak rate, although to a lower degree than expected. Conclusion: Because of the transition into molecular gas flow through regolith, vacuum testing is required to properly estimate performance. Regolith columns should be designed as narrow as possible to avoid bridging and minimize leak rate, and as tall as is feasible to both further reduce leak rate and to help prevent bubbling, which has been shown to degrade the quality of the regolith seal. Disrupted soil was found to exhibit higher leak rates than pristine, as-poured soil, indicating the need to consider the impact of recovery from depressurization events. Regolith columns appear equally feasible for both dosed and continuous-feed reactors.

ISRU↗
NASA NTRS2023

Space Networking Implementation for Lunar Operations

The High-Rate Delay Tolerant Networking (HDTN) project at NASA has developed a performance optimized and open-source Delay Tolerant Networking (DTN) implementation. The primary goal is to create a scalable networking solution to increase the scientific data return rate of space missions. To reach this goal, HDTN must span multiple edge cases in space networking by including tools and configurations to accommodate a wide range of space systems. Typically, HDTN evaluations are conducted on a laboratory emulation test bed, made up of hardware accelerated x86 based systems capable of data rates over 10 Gbps. HDTN must have an effective implementation process on a wide range of systems to increase the sustainability of the design. One important implementation option is with low-level embedded systems which could be used on small robotic missions. This paper details the implementation process, benchmark testing, and performance results of HDTN in multiple configurations on Raspberry Pi 4 devices. By implementing HDTN on a Raspberry Pi 4, a process for building HDTN onto ARM processors was developed and utilized to conduct benchmark tests in multiple network configurations, achieving a data rate performance exceeding 600 Mbps. Based on these results, HDTN proved to run on small ARM based systems with slight modifications to the build procedure. These results were then extended to evaluating an implementation of the HDTN software parsed across several Raspberry Pi 4 nodes. To test this capability, HDTN was configured in a simplified cut-through setup and distributed among multiple Raspberry Pi 4 processors. This distributed architecture was benchmark tested in a similar fashion to the testing of a singular HDTN implementation. The results from the benchmark testing are used to examine how these implementation options and capabilities can expand the use cases for DTN, and particularly with small robotic missions.

Space Networking↗
NASA NTRS2023

Comparing the Electrical Modeling and Thermal Analysis Toolbox Simulation Data to Electrified Aircraft Propulsion Test Hardware Data

A model using the Electrical Modeling and Thermal Analysis Toolbox (EMTAT), a National Aeronautics and Space Administration (NASA)-developed Simulink® model block library of electrical components, was developed to mirror the Hybrid Propulsion Emulation Rig (HyPER) hardware, a laboratory focused on Electrified Aircraft Propulsion (EAP) hardware tests. The goal of the model was to demonstrate the utility of the library by comparing the accuracy of the library models to the performance of real hardware, with the primary metrics being the simulation outputs matching physical test hardware data within 5 percent of full scale. The objective of this paper is to present the background, setup, testing and results of this comparison. It describes some of the adjustments that were necessary to match the system hardware, as well as next steps in verification and validation. The outputs of the model were compared to the results of several tests in HyPER, and in the process captured an additional torque loss that is still being analyzed for the root cause but has been confirmed in the hardware. Across all the test series, only one key model parameter was outside the target 5 percent full scale matching, and nearly 70 percent were within 1 percent.

Mark E. Bell↗
NASA NTRS2023

Real-Time Hardware-in-the-Loop Evaluation of A Partially Turboelectric Propulsion Control Design

In support of aviation fuel burn and emission reduction goals, NASA is pursuing high-payoff research investments that promise to transform aviation. This includes investments in Electrified Aircraft Propulsion (EAP). Multiple technology challenges must be addressed to unlock the full potential of EAP. This includes addressing challenges related to propulsion controls, which will be vital for ensuring efficient coordinated operation of EAP subsystems. This paper presents results from real-time hardware-in-theloop (HIL) testing of a control design for a single aisle partially-turboelectric aircraft propulsion concept conducted at the NASA Electric Aircraft Testbed (NEAT) facility. The control system under test is designed for a propulsion concept consisting of two wing-mounted turbofan engines that produce thrust and generate electrical power to drive a boundary layer ingesting tailfan propulsor via an electrical motor. An integrated control strategy is applied to ensure coordinated operation of the turbofan and tailfan subsystems during steady-state and transient operation throughout the flight envelope. The NEAT test of this integrated control design consists of a partially HIL, partially simulated configuration. A subscale representation of the electrical system design is implemented in hardware and mechanically coupled to electric machines that emulate turbomachinery and propulsor shaft dynamics. The hardware configuration is then operated under the control of a real-time computer application that runs a simulation of the propulsion system and the developed control logic. The NEAT facility test campaign includes a series of experiments that subject the control design to throttle transients conducted throughout the flight envelope and full-flight mission profiles. Testing under simulated performance degradation is also conducted to evaluate control design robustness. This includes constant and abrupt changes in degradation levels. Results from the HIL test are presented and shown to be in good agreement with pretest simulation predictions demonstrating the efficacy of the integrated control design approach.

Electrified Aircraft Propulsion↗
NASA NTRSDate not supplied

Space Grant Final Paper

The purpose of this internship was to begin the development of an APK that would subscribe to NavCam and video stream via UDP. This project involved having the Astrobee Robot Software installed, the Astrobee Android Repository, and the use of an android emulator. While the final APK currently cannot stream via UDP, it can still subscribe to the topic, which for me was already a challenge.

Astrobee↗
NASA NTRSDate not supplied

Efficient Power Management of an Active Phased Array Antenna Via Circular Aperture Reduction

Significant commercial investments in terrestrial 5G communication systems have matured state-of-the-art Ka-band active phased array (APA) antennas, and their entrance into integrated SATCOM terminals provides space mission designers with new trades and considerations. Newly available Ka-band APAs could provide future missions with a small form factor terminal (<1000 cm3) that can perform rapid beam steering without any moving components. However, APA systems generally consume more power than alternative terminal configurations, which motivates our investigation into a power management technique that leverages the APA’s ability to disable individual antenna elements to rapidly trade excess signal strength for reduced power consumption. Our algorithm strategically maps a desired transmitter effective isotropic radiated power (EIRP) to a binary element mask that simultaneously minimizes the number of active elements and circularizes the antenna’s aperture. We deployed our algorithm on a Cesium Nightingale 1 terminal and emulated a 1.05 Gbps constant-rate link between a low Earth orbit (LEO) satellite and a ground station in an over-the-air test. During the 7m42s pass, the aperture reduction algorithm reduced the average power consumption of the terminal by 27%, the average number of active elements by 56%, and saved 3.9 Wh of energy.

satellite communications↗
NASA NTRS2023

An Examination of Heavy Ion-Induced Persistent Visual Error Signatures in an Electronic Display Driver Integrated Circuit

Given the ubiquity of electronic displays integration in human-based systems, the impending mission critical, space-based applications of electronic displays will necessitate SEE assessment of components unique to electronic displays. A commercially available DDIC designed to drive a small form factor organic light emitting diode (OLED) was visually monitored during heavy ion irradiation to catalogue radiation induced persistent visual error signatures that require manual intervention (i.e., power cycling) to return to nominal function. These error signatures were able to be reproduced via modification of configuration register values utilizing the instruction set intended for interfacing a microcontroller with the DDIC. This approach to emulation of heavy-ion induced errors on a table-top assists with human perception-based criticality analysis as well as development of mitigation techniques.

Electronic Displays↗
NASA NTRS2023

Lunar LTE Studies DRATS 2022 Report

In October 2022, the Lunar LTE Studies (LunarLiTES) team from the National Aeronautics and Space Administration (NASA) Glenn Research Center (GRC) conducted a series of communications field test measurements through the NASA Desert Research and Technology Studies (DRATS) campaign held near Flagstaff, Arizona. The objective of the NASA DRATS outings are to provide analog mission testing of candidate technologies for space exploration, especially those technologies applicable to human exploration of extraterrestrial rocky bodies. These activities are performed at locations with similarities to extraterrestrial conditions, such as the dry, volcanic landscape north of Flagstaff. This report describes the surface-to-surface communications testing performed by LunarLiTES as part of the 2022 NASA DRATS experiments. The objectives of this testing were to collect data for the development and refinement of radio frequency (RF) propagation models and emulation techniques, as well as to evaluate the application of terrestrial cellular communication technologies to lunar surface exploration.

lunar communication↗
NASA NTRSDate not supplied

Initial Study of Tailored Trajectory Management for Multi-Vehicle Uncrewed Regional Air Cargo Operations

The primary contribution of this paper is an evaluation of the potential value of a tailored trajectory management (TTM) capability for uncrewed aircraft (UA) operators that is proactive in detecting conflicts and developing trajectory-based solutions for UA prior to air traffic control (ATC) performing conflict resolution. The experiment matrix is composed of one baseline simulation that models current air traffic operations without such a capability and four test simulations with different configurations of such a capability. In each simulation, five UA operations into Fort Worth Alliance airport were modeled in the presence of recorded tracks for about 4700 flights on January 18, 2022. The analysis focused on the extent to which such a capability was able to preclude an event that could spike UA operator workload. More specifically, in this study, the emulated UA operator TTM capability for multi-vehicle regional air cargo operations was able to reduce the number of instances of concurrent UA conflicts in the modeled ATC conflict resolution timeframe of 8 minutes or less from three to as low as one.

uncrewed aircraft, regional air cargo, tailored tr↗
NASA NTRS2024

4K High Definition Video and Audio Streaming Across High-rate Delay Tolerant Space Networks

Audio and video streaming across delay tolerant networks are relatively new phenomena. During the Apollo 11 mission, video and audio were streamed directly back to Earth using fully analog radios. This streaming capability atrophied over time due to the gradual conversion to digital electronics accompanied with higher resolutions causing the required bit rates to outpace communication link performance. Additionally, 21st century space systems face the new requirement of interconnectedness. Delay Tolerant Networking (DTN) attempts to solve this requirement by uniting traditional point to point links into a robust and dynamic network. However, In order to avoid system bottlenecks, the High-Rate Delay Tolerant Networking (HDTN) implementation focuses on performance-optimization of the standards. This work extends the functionality of HDTN by implementing audio and video streaming, with the goal of demonstrating the practical application of high definition media streaming across space networks. A series of network topologies were created including simple point to point links and multi-node multi-hop networks. Test media in the form of prerecorded and live footage was streamed across the network. A set of objective quality metrics were established in order to measure the stream quality. A lunar network was emulated using a mixture of embedded ARM platforms.

Kyle J Vernyi↗