Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Electrode materials”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Amorphous Pd-Loaded Ti 4 O 7 Electrode for Direct Anodic Destruction of Perfluorooctanoic Acid

In this work we present a novel Ti 4 O 7 -based electrode loaded with amorphous Pd clusters that achieve efficient anodic destruction of perfluorooctanoic acid (PFOA), a persistent water pollutant with significant environmental and human health concerns. These amorphous Pd clusters were characterized by the disordered, noncrystalline arrangement of Pd single atoms in close proximity, in contrast to crystalline Pd nanoparticles that have been often employed to tailor the electronic properties of an electrode. We found that the Ti 4 O 7 electrode loaded with amorphous Pd clusters significantly outperformed the Ti 4 O 7 electrode loaded with crystalline Pd particles due to enhanced electron transfer through dominant Pd–O bonds. Combined with the efficient binding of PFOA and its degradation intermediates to the fluorinated electrode surface, this electrode was capable of mineralizing PFOA and releasing fluoride as F – . The reaction pathway was found to proceed without involving reactive oxygen species and therefore was not quenched by common anions in complex natural water systems such as chloride ions.

36 MATERIALS SCIENCE↗
DOE OSTI2020

In-Situ Characterization of Dynamic Morphological and Phase Changes of Selenium-doped Germanium Using a Single Particle Cell and Synchrotron Transmission X-ray Microscopy

The dynamic information of lithium-ion battery active materials obtained from coin cell-based in-situ characterizations might not represent the properties of the active material itself because many other factors in the cell could have impacts on the cell performance. To address this problem, a single particle cell was developed to perform the in-situ characterization without the interference of inactive materials in the battery electrode as well as the X-ray-induced damage. In this study, the dynamic morphological and phase changes of selenium-doped germanium (Ge 0.9 Se 0.1 ) at the single particle level were investigated via synchrotron-based in-situ transmission X-ray microscopy. The results demonstrate the good reversibility of Ge 0.9 Se 0.1 at high cycling rate that helps understand its good cycling performance and rate capability. This in-situ and operando technique based on a single particle battery cell provides an approach to understanding the dynamic electrochemical processes of battery materials during charging and discharging at the particle level.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Critical Practices in Rigorously Assessing the Inherent Activity of Nanoparticle Electrocatalysts

Accurate activity measurements for electrocatalytic materials are the backbone of impactful electrocatalyst research. Inherent to accurate measurements is the correct accounting of the active catalyst sites and the design of experiments to ensure that these sites are participating in the measured reaction. Improvements in electrocatalyst activity for fuel cell reactions (hydrogen oxidation and oxygen reduction) are essential for the widespread adoption of this carbon-neutral energy source. Activities for these half-reactions can be reported in a variety of ways including specific activities, mass activities, volumetric activities, and half-wave potentials. These values are traditionally measured with a rotating disk electrode (RDE) in which the electrocatalyst is supported on a porous active layer film attached to the RDE. To accurately measure electrocatalyst activity with an RDE, two major sources of errors must be addressed: (i) accurate electrochemical surface area (ECSA) quantification and (ii) fast diffusion of reactants through the active layer film. In this contribution, we first aim to detail through RDE experiments and mass transport modeling the potential errors that can be observed when these factors are not properly addressed. We then present recommendations and discuss techniques for properly constructing electrocatalyst thin films and characterizing the ECSA on monometallic and novel alloy electrocatalysts. These practices, when adopted, ensure greater confidence and reliability in reports of electrocatalyst activity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Ultra-efficient polymer binder for silicon anode in high-capacity lithium-ion batteries

As a highly promising anode material for high-capacity lithium-ion batteries (LIBs), the low electronic conductivity and large volume variation of silicon (Si) make the slurry-coating Si based electrode requiring high content of “inert” materials and suffering rapid capacity fading. In this work, a polyimine, synthesized via one-step condensation reaction, has been demonstrated as an ultra-efficient polymer binder that can resolve the above issues. The polyimine binder containing Si electrode delivers superior electrochemical performance: a delithiation specific capacity of 804.4 mAh g –1 with capacity retention of 82.4% after 1000 cycles at the current density of 2 A g –1 . The high efficiency of polyimine binder for Si electrode has also been demonstrated with ultrahigh weight ratio of “active” material to “inert” material (R A/I ). The electrode with 95 wt% of Si (95Si/Polyimine, R A/I = 19) reveals a reversible delithiation capacity of 2114 mAh g –1 (capacity retention ~ 80.4%) over 200 cycles at the current density of 400 mA g –1 . Even at the high current density of 2 A g –1 , a delithiation capacity of 1087.8 mAh g –1 after 500 cycles can be obtained. Molecular simulations and atomic force microscopy (AFM) indentation are utilized to investigate the ultra-efficiency of polyimine binder. With simple manufacturing process and ultra-efficient binder performance, the designed polyimine binder will be definitely meaningful in achieving low-cost and high-capacity LIBs with prolonged cycle life.

25 ENERGY STORAGE↗
DOE OSTI2021

Challenges for and Pathways toward Li-Metal-Based All-Solid-State Batteries

Solid-state batteries utilizing Li metal anodes have the potential to enable improved performance (specific energy >500 Wh/kg, energy density >1500 Wh/L), safety, recyclability, and potentially lower cost (<$100/kWh) compared to advanced Li-ion systems.1,2 These improvements are critical for the widespread adoption of electric vehicles (EVs) and trucks and could create a short-haul electric aviation industry.1-3 Expectations for solid-state batteries are high, but there are significant materials and processing challenges to overcome.

25 ENERGY STORAGE↗
DOE OSTI2021

Unlocking anionic redox activity in O3-type sodium 3 d layered oxides via Li substitution

Sodium ion batteries, because of their sustainability attributes, could be an attractive alternative to Li-ion technology for specific applications. However, it remains challenging to design high energy density and moisture stable Na-based positive electrodes. Here, we report an O3-type NaLi 1/3 Mn 2/3 O 2 phase showing anionic redox activity, obtained through a ceramic process by carefully adjusting synthesis conditions and stoichiometry. This phase shows a sustained reversible capacity of 190 mAh g -1 that is rooted in cumulative oxygen and manganese redox processes as deduced by combined spectroscopy techniques. Unlike many other anionic redox layered oxides so far reported, O3-NaLi 1/3 Mn 2/3 O 2 electrodes do not show discernible voltage fade on cycling. This finding, rationalized by density functional theory, sheds light on the role of inter- versus intralayer 3d cationic migration in ruling voltage fade in anionic redox electrodes. Another practical asset of this material stems from its moisture stability, hence facilitating its handling and electrode processing. Altogether, this work offers future directions towards designing highly performing sodium electrodes for advanced Na-ion batteries.

25 ENERGY STORAGE↗
DOE OSTI2025

General kinetic ion-induced electron emission model for metallic walls applied to biased Z-pinch electrodes

A kinetic ion-induced electron emission (IIEE) model for general applications is developed to obtain the emitted electron energy spectrum for a distribution of ion impacts on a metallic surface. We assume an ionization cascade mechanism and use empirical models for the ion and electron stopping powers. The emission spectrum and the secondary electron yield (SEY) are validated for a variety of materials. The IIEE model is used to study the effect of IIEE on the plasma-material interactions of Z-pinch electrodes. Un-magnetized Boltzmann-Poisson simulations are performed for a Z-pinch plasma doubly bounded by two biased copper electrodes with and without IIEE at bias potentials from 0 to 9 kV. At the anode, the SEY decreases from 0 to 1 kV, but then increases at higher bias potentials. At the cathode, the SEY is much larger due to higher energy ion bombardment and grows with bias potential. As the bias potential increases, the emitted cathode electrons are accelerated to higher energies into the domain, collisionally heating the plasma. Above 1 kV, the heating is strong enough to increase the plasma potential. Despite SEY greater than 1, only a classical sheath forms as opposed to a space-charge limited or inverse sheath due to the emitted electron flux not reaching the space charge current saturation limits. Furthermore, the current in the emissionless cases saturates to a value lower than experiment. With IIEE, the current does not saturate and continues to increase with the 4 kV case, matching most closely with the experiment.

Carbon based materials↗
DOE OSTI2022

Multiphase layered transition metal oxide positive electrodes for sodium ion batteries

Abstract Multiphase layered transition metal oxides (LTMOs) for sodium ion battery (SIB) positive electrodes with phase interfaces across multiple length scales are a promising avenue toward practical, high‐performance SIBs. Combinations of phases can complement each other's strengths and mitigate their weaknesses if their interfaces are carefully controlled. Intra‐ and interparticle phase interactions from nanoscale to macroscale must be carefully tuned to generate distinct effects on properties and performance. An informed design strategy must be paired with relevant synthesis techniques and complemented by spatially resolved characterization tools to manipulate different length scales and interfaces. This review examines the design, synthesis, and characterization strategies that have been demonstrated for the preparation of heterogeneous, multiphasic LTMOs with phase interfaces across varied length scales.

25 ENERGY STORAGE↗
DOE OSTI2025

Spinel-Structured High Entropy Oxides: Low Temperature Synthesis, Characterization, and Potential Applications

High entropy oxides (HEOs) have recently attracted increasing attention due to their remarkable properties and relatively low cost. Herein we report a simple, highly scalable, and low temperature method for synthesizing spinel (FeNiCoCuZn) 3 O 4 (HEO). We heated an aqueous solution containing divalent cations in high alkali environments to temperatures of 25 - 95 °C for 24 h under atmospheric pressure. The HEO, synthesized at 95 °C for 24 h in 1 M KOH, was paramagnetic at room temperature, with a magnetic mass susceptibility of χ = (7.5 ± 0.2) × 10 –7 m 3 ·kg –1 . It demonstrated stable electrochemical lithium storage performance, with a gravimetric capacity of ∼300 mAh·g –1 at 100 mA·g –1 . It was also active in the electrocatalytic oxygen evolution reaction with an overpotential of 460 mV in alkaline media. The band gap energies were in the range of 2.4 eV. Our advancement in the synthesis and processing of transition metal-based HEOs will undoubtedly render them a viable solution for next generation materials for energy production and storage.

diffraction↗
DOE OSTI2020

A Cation-Tethered Flowable Polymeric Interface for Enabling Stable Deposition of Metallic Lithium

A fundamental challenge, shared across many energy storage devices, is the complexity of electrochemistry at the electrode–electrolyte interfaces that impacts the Coulombic efficiency, operational rate capability, and lifetime. Specifically, in energy-dense lithium metal batteries, the charging/discharging process results in structural heterogeneities of the metal anode, leading to battery failure by short-circuit and capacity fade. In this work, we take advantage of organic cations with lower reduction potential than lithium to build an electrically responsive polymer interface that not only adapts to morphological perturbations during electrodeposition and stripping but also modulates the lithium ion migration pathways to eliminate surface roughening. As a result, we find that this concept can enable prolonging the long-term cycling of a high-voltage lithium metal battery by at least twofold compared to bare lithium metal.

25 ENERGY STORAGE↗
DOE OSTI2020

Ca Cobaltites as Potential Cathode Materials for Rechargeable Ca-Ion Batteries: Theory and Experiment

Rechargeable Ca-based batteries can potentially achieve higher energy capacity than Li-ion batteries. The development of Ca-ion batteries, however, remains in its infancy, especially due to the challenge of finding cathode materials with high reversible capacity. In this work, we investigate properties of Ca cobaltites as Ca-ion intercalation cathodes, by means of density functional theory calculations validated by synthesis and electrochemical measurements. Computationally, we accessed thermodynamic, diffusion properties, energy capacity, and the voltage profiles for four Ca cobaltite compounds of different stoichiometry and Co oxidation states: Ca 3 Co 2 O 6 , CaCo 2 O 4 , Ca 2 Co 2 O 5 , and [Ca 2 CoO 3 ][CoO 2 ] 1.62 . We found good stability and relatively low migration barriers of some Ca cobaltites during cycling with the layered CaCo 2 O 4 having the lowest Ca migration barrier of 0.7 eV and the highest theoretical capacity. To validate our calculations, we synthesized Ca 3 Co 2 O 6 , CaCo 2 O 4 , and [Ca 2 CoO 3 ][CoO 2 ] 1.62 with the Pechini method and, subsequently, to test the electrochemical extraction of Ca.

25 ENERGY STORAGE↗
DOE OSTI2023

Dual-Band Electrochromism in Hydrous Tungsten Oxide

The independent modulation of visible and near-infrared light by a single material, termed dualband electrochromism, is highly desirable for smart windows to enhance the energy efficiency of buildings. Tungsten oxides are commercially important electrochromic materials, exhibiting reversible visible and near-infrared absorption when electrochemically reduced in an electrolyte containing small cations or protons. The presence of structural water in tungsten oxides has been associated with faster electrochromic switching speeds. Here, we find that WO 3 ·H 2 O, a crystalline hydrate, exhibits dual-band electrochromism unlike the anhydrous WO 3 providing a heretofore unexplored route to tune the electrochromic response of tungsten oxides. Absorption of near-infrared light is achieved at low Li + /e - injection, followed by the absorption of visible light at higher Li + /e - injection as a result of an electrochemically-induced phase transition. We propose that this dual-band modulation is possible due to the more open structure of WO 3 ·H 2 O as compared to WO 3 . This facilitates a more extended solid solution Li + insertion regime that benefits the modulation of near-infrared radiation via plasmon absorption. Higher degrees of Li + /e - insertion lead to polaronic absorption associated with localized charge storage. Furthermore, these results inform how structural factors influence the electrochemically induced spectral response of transition metal oxides and the important role of structural water beyond optical switching speed.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗
DOE OSTI2023

Progresses and Perspectives of All‐Iron Aqueous Redox Flow Batteries

Abstract Redox flow batteries (RFBs) are a promising option for long‐duration energy storage (LDES) due to their stability, scalability, and potential reversibility. However, solid‐state and non‐aqueous flow batteries have low safety and low conductivity, while aqueous systems using vanadium and zinc are expensive and have low power and energy densities, limiting their industrial application. An approach to lower capital cost and improve scalability is to utilize cheap Earth‐abundant metals such as iron (Fe). Nevertheless, all‐iron RFBs have many complications, involving voltage loss from ohmic resistance, side reactions such as hydrogen evolution, oxidation, and most significantly electrode plating, and dendrite growth. To address these issues, researchers have begun to examine the effects of various alterations to all‐iron RFBs, such as adding organic ligands to form Fe complexes and using a slurry electrode instead of common materials such as graphite or platinum rods. Overall, progress in improving aqueous all‐iron RFBs is at its infant stage, and new strategies must be introduced, such as the utilization of nanoparticles, which can limit dendrite growth while increasing storage capacity. This review provides an in‐depth overview of current research and offers perspectives on how to design the next generation of all‐iron aqueous RFBs.

Belongia, Shawn↗
DOE OSTI2021

Localized corrosion: Passive film breakdown vs. Pit growth stability, Part VI: Pit dissolution kinetics of different alloys and a model for pitting and repassivation potentials

Here, the pitting resistance of SS316L, SS304, SS430, and pure Fe was studied in chloride-containing solution. Among these alloys, SS316L exhibits the highest pit initiation rate, but also the highest pitting potential. To explain this phenomenon, the maximum pit dissolution current density (i diss,max ) of the alloys in saturated pit solution was measured using one-dimensional artificial pit electrodes. A lower i diss,max was found to correlate with higher pitting and repassivation potentials. Based on a recently proposed pitting framework, a conceptual model for pitting and repassivation potentials was established, based on which the effect of i diss,max on pitting resistance was discussed.

one-dimensional artificial pit electrode↗
DOE OSTI2023

Cracking vs. surface reactivity in high-nickel cathodes for lithium-ion batteries

High-nickel layered oxide cathodes LiNi x Mn y Co z O 2 (NMC) experience microcracks during cycling. This can expose fresh cathode surfaces for parasitic reactions and isolate active cathode material from the conductive electrode matrix, resulting in impedance increase and capacity fade. The commonly held belief attributes microcracks to anisotropic lattice volume changes of primary particles during cycling. Nevertheless, recent reports suggest that certain electrolytes might reduce microcracks in NMC cathodes during deep cycling. This raises a crucial question on the origin of microcracks: do microcracks exacerbate surface stability, or does poor surface stability contribute to microcrack formation? This perspective aims to provide context and expound this “chicken or egg” dilemma. We contend that the consequence of surface reactivity on the cycle life of high-Ni cathodes is more pronounced than that of particle cracking. Here, we hypothesize that particle cracking is more of a symptom of severe surface reactivity rather than a cause of capacity fade.

25 ENERGY STORAGE↗
DOE OSTI2023

The impacts of membrane pinholes on PEM water electrolysis

Polymer electrolyte membrane (PEM) water electrolysis is a promising technology to efficiently produce green hydrogen. Irregularities in membrane electrode assembly (MEA) component materials caused by manufacturing, processing, handling, or operation can lead to performance loss and failure. One example is the presence of pinholes in the membrane, which can cause increased gas transport (crossover) and lead to electrical shorting. This work investigates the effects of intentionally introduced pinholes with various sizes up to 350μm in diameter. The presence of the pinholes resulted in minimal impacts on the cell voltage (±30 mV at 4Acm -2 ). However, the pinholes significantly increased H 2 crossover, which decreased hydrogen production efficiency and increased the minimum current density for safe operation. The impacts of the pinhole on the H 2 crossover and efficiency are more severe for open pinhole features than tear-like pinhole features. In conclusion, this research demonstrates that even small pinholes cannot be disregarded from a safety, efficiency, and operating strategy perspective.

08 HYDROGEN↗
DOE OSTI2020

Thermally Driven Interfacial Degradation between Li 7 La 3 Zr 2 O 12 Electrolyte and LiNi 0.6 Mn 0.2 Co 0.2 O 2 Cathode

Solid-state batteries offer higher energy density and enhanced safety compared to the present lithium-ion batteries using liquid electrolytes. A challenge to implement them is the high resistances, especially at the solid electrolyte interface with the cathode. Sintering at elevated temperature is needed in order to get good contact between the ceramic solid electrolyte and oxide cathodes and thus to reduce contact resistances. Many solid electrolyte and cathode materials react to form secondary phases. It is necessary to find out which phases arise as a result of interface sintering and evaluate their effect on electrochemical properties. Herein, we assessed the interfacial reactions between LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) and Li 7 La 3 Zr 2 O 12 (LLZO) as a function of temperature in air. We prepared model systems by depositing thin-film NMC622 cathode layers on LLZO pellets. The thin-film cathode approach enabled us to use interface-sensitive techniques such as X-ray absorption spectroscopy in the near-edge as well as the extended regimes and identify the onset of detrimental reactions. We found that the Ni and Co chemical environments change already at moderate temperatures, on-setting from 500 °C and becoming especially prominent at 700 °C. By analyzing spectroscopy results along with X-ray diffraction, we identified Li 2 CO 3 , La 2 Zr 2 O 7 , and La(Ni,Co)O 3 as the secondary phases that formed at 700 °C. The interfacial resistance for Li transfer, measured by electrochemical impedance spectroscopy, increases significantly upon the onset and evolution of the detected interface chemistry. Our findings suggest that limiting the bonding temperature and avoiding CO 2 in the sintering environment can help to remedy the interfacial degradation.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Depth-Dependent Understanding of Cathode Electrolyte Interphase (CEI) on the Layered Li-Ion Cathodes Operated at Extreme High Temperature

The high-temperature operation of Li-ion batteries is highly dependent on the stability of the cathode electrolyte interphase (CEI) formed during lithiation-delithiation reactions. However, knowledge on the nature of the CEI is limited and its stability under extreme temperatures is not well understood. Therefore, herein, we investigate a proof-of-concept study on stabilizing CEI on model LiNi 0.33 Mn 0.33 Co 0.33 O 2 (NMC333) at extreme operation condition of 100 oC using thermally stable pyrrolidinium based ionic liquid electrolyte. The electrochemical lithiation-delithiation reactions at 100 oC and the CEI evolution upon different cycling conditions are investigated. Further, the depth-dependent CEI chemistry was investigated using energy tunable synchrotron-based hard X-ray photoelectron spectroscopy (HAXPES). Overall, the results reveal that the high temperature operation accelerated the CEI formation compared to room temperature, and the surface of the interphase layer is rich in boron-based inorganic moieties than the deeper surface. Further, bulk sensitive X-ray absorption spectroscopy (XAS) was used to investigate the transition metal redox contributors during high temperature electrochemical reactions, similar to room temperature, the Ni2+/4+redox couple is the only charge compensating redox couple during high temperature operation. Finally, the physical nature of the conformal CEI on the cathode particles was visualized with high-resolution transmission electron microscopy, which confirms that the significant degradation of cathode particles without conformal CEI is due to the transformation of layer to spinel formation at extreme temperature. In this study, understanding this high temperature interfacial chemistry of NMC cathodes through advanced spectroscopy and microscopy will shed light on transforming ambient temperature Li-ion chemistry to high temperature applications.

25 ENERGY STORAGE↗