Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC PROPERTY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Impact of silver metallization and electron irradiation on the mechanical deformation of polyimide films

The impact of silver metallization and electron irradiation on the physical and mechanical properties of polyimide films has been studied. The metal that impregnated the structure of the polyimide substrate was 1–5 μm. The surface coatings contained 80–97% of the relative silver mirror in the visible and infrared regions. Irradiation was performed at the ELU-6 linear accelerator with an average beam electron energy of 2 MeV, an integral current of up to 1000 μA, a pulse repetition rate of 200 Hz, and a pulse duration of 5 μs. The absorbed dose in the samples was 10, 20, 30, and 40 MGy. The samples were deformed at room temperature under uniaxial tension on an Instron 5982 universal testing system. The structural changes in the composite materials that result from the impact of the physical factors were studied using an X-ray diffractometer DRON-2M in air at 293 K using CuK{sub α} radiation (λ{sub αCu} = 1.5418 Å). A substantial growth of mechanical characteristics resulting from the film metallization, as compared to the pure film, was observed. The growth of the ultimate strength by Δσ = 105 MPa and the plasticity by Δε = 75% is connected with the characteristics of the change of structure of the metallized films and the chemical etching conditions. The electron irradiation of the metallized polyimide film worsens its elastic and strength characteristics due to the formation of new phases in the form of silver oxide in the coating. The concentration of these phases increased with increasing dose, which was also the result of the violation of the ordered material structure, namely, the rupture of polyimide macromolecule bonds and the formation of new phases of silver in the coating. A mathematical model was obtained that predicts the elastic properties of silver metallized polyimide films. This model agrees with the experimental data.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Mechanical Properties of Nominally Ductile and Brittle Zones within the Caney Shale Formation

We present a case study from the Caney Shale, which is an emerging hydrocarbon-bearing formation in Oklahoma. Open hole logs lead to a nominal distinction of five zones in an exploration well, two of which are designated “ductile” and three of which are designated as less ductile “reservoir” zones. Subsequently, a detailed mechanical characterization was carried out on core plugs taken from each of these zones. Results show nominally “ductile” zones are weaker in terms of UCS, tensile strength, fracture toughness, and confined compressive strength. However, by a variety of brittleness indices, it is found the nominal “ductile” regions do not behave as expected. They are weaker, but not consistently more ductile. Furthermore, some brittleness indices lead to contradictory conclusions. For example, zones which would be considered the most brittle according to the proportion of nonlinear stress-strain behavior prior to failure and/or by indices based on elastic properties would be considered the least brittle according to their internal friction angle.

Benge, Margaret↗

Continuum modeling of three-dimensional truss-like space structures

A mathematical and computational analysis capability has been developed for calculating the effective mechanical properties of three-dimensional periodic truss-like structures. Two models are studied in detail. The first, called the octetruss model, is a three-dimensional extension of a two-dimensional model, and the second is a cubic model. Symmetry considerations are employed as a first step to show that the specific octetruss model has four independent constants and that the cubic model has two. The actual values of these constants are determined by averaging the contributions of each rod element to the overall structure stiffness. The individual rod member contribution to the overall stiffness is obtained by a three-dimensional coordinate transformation. The analysis shows that the effective three-dimensional elastic properties of both models are relatively close to each other.

Nayfeh, A. H.↗

Effective elastic thickness of the Venusian lithosphere with lateral viscosity variations in the mantle

Both the Earth and Venus have a convecting mantle at the top of which is a relatively strong, mechanical boundary layer. The surface topography and gravity signals which result from the convection within the viscous mantle are modified by the elastic properties of this lithospheric boundary layer. In particular the ability of the lithosphere to support loads and transmit stresses from below is a function of the wavelength of the load--the lithosphere is strong to loading at shorter wavelengths. As a consequence it is usual to expect that long wavelength topography cannot be supported by the mechanical strength of the lithosphere and must be compensated--isostatically or dynamically--within the uppermost mantle or the crust. The flexural rigidity of the lithosphere can therefore be determined by estimating the greatest wavelength at which uncompensated surface topography can be supported, usually by measuring the admittance as a function of wavelength. In fact this procedure for determining the elastic thickness relies upon being able to distinguish topography with underlying support from that supported by the brittle lithosphere on the basis of their each having a characteristic value of the admittance. However, in the presence of lateral viscosity variations in the mantle, it is possible for topography to be generated which is NOT compensated by density anomalies in the underlying mantle at the same wavelength. Although this effect is not likely to be important for the Earth, on Venus, where the high surface temperatures would be expected to give a weaker lithosphere, lateral viscosity variations in the mantle can give a misleadingly large apparent elastic thickness for the lithosphere.

Moresi, Louis↗

Super-hybrid composites - An emerging structural material

Specimens of super-hybrids and advanced fiber composites were subjected to extensive tests to determine their mechanical properties, including impact and thermal fatigue. The super-hybrids were fabricated by a procedure similar to that reported by Chamis et al., (1975). Super-hybrids subjected to 1000 cycles of thermal fatigue from -100 to 300 F retained over 90% of their longitudinal flexural strength and over 75% of their transverse flexural strength; their transverse flexural strength may be as high as 8 times that of a commercially supplied boron/1100-Al composite. The thin specimen Izod longitudinal impact resistance of the super-hybrids was twice that of the boron/110-Al material. Super-hybrids subjected to transverse tensile loads exhibited nonlinear stress-strain relationships. The experimentally determined initial membrane (in-plane) and bending elastic properties of super-hybrids were predicted adequately by linear laminate analysis.

Chamis, C. C.↗

Thermo-Mechanical Response of a TRISO Fuel Particle in a Fusion/Fission Engine for Incineration of Weapons Grade Plutonium

The Laser Inertial Fusion-based (LIFE) engine is an advanced energy concept under development at Lawrence Livermore National Laboratory (LLNL). LIFE engine could be used to drive a subcritical fission blanket with fertile or fissile fuel. Current LIFE engine designs envisages fuel in pebble bed form with TRISO (tristructural isotropic) particles embedded in a graphite matrix, and pebbles flowing in molten salt Flibe (2LiF+BeF{sub 2}) coolant at T {approx} 700C. Weapons-grade plutonium (WGPu) fuel is an attractive option for LIFE engine involving the achievement of high fractional burnups in a short lifetime frame. However, WGPu LIFE engine operating conditions of high neutron fast fluence, high radiation damage, and high Helium and Hydrogen production pose severe challenges for typical TRISO particles. The thermo-mechanical fuel performance code HUPPCO (High burn-Up fuel Pebble Performance COde) currently under development accounts for spatial and time dependence of the material elastic properties, temperature, and irradiation swelling and creep mechanisms. In this work, some aspects of the thermo-mechanical response of TRISO particles used for incineration of weapons grade fuel in LIFE engine are analyzed. Preliminary results show the importance of developing reliable high-fidelity models of the performance of these new fuel designs and the need of new experimental data relevant to WGPu LIFE conditions.

36 MATERIALS SCIENCE↗

Imaging transient melting of a nanocrystal using an X-ray laser

Significance Despite phase transitions, such as melting, being ubiquitous in nature, understanding what occurs at the nanoscale (such as in nanocrystals) has so far remained challenging. With ensemble studies of nanocrystals it is often difficult to discriminate between intrinsic size-dependent properties and effects due to sample size and shape dispersity. Here, using an X-ray free electron laser we image the reversible melting of an individual nanocrystal induced by an ultrashort laser. It is revealed that the melting occurs transiently, repeatably, and inhomogeneously. This is consistent with a core-shell model where the exterior is melted and a solid core remains. These findings reveal, unambiguously, that core-shell melting occurs, which has important implications for understanding nanoscale phenomena.

Clark, Jesse N.↗

Elastic anomalies across phase transitions of praseodymium to 12 GPa

The elastic properties of praseodymium (Pr) were investigated at pressures up to 12 GPa at room temperature using ultrasonic interferometry technique. Softening and discontinuities in compressional (P) and shear (S) wave velocities were observed at around 2.5, 6.5 and 10.5 GPa, which are interpreted as indications of the phase transitions from Pr-I (dhcp) to Pr-II (fcc), Pr-II (fcc) to Pr-III (d-fcc) and Pr-III (d-fcc) to Pr-VII (monoclinic or orthorhombic), respectively. Very small discontinuities in compressibility have been observed across the phase transitions of I-II and II-III of Pr, which are unlikely visible in the X-ray diffraction studies. Finally, a comparison with the elastic behaviors of other lanthanide elements (e.g., Ce and La) suggests that the elastic anomalies associated with these phase transitions are likely to be caused by the 6s-5d electron transfer and the softening of acoustic phonon mode facilitated by decreased atomic distances under pressure.

36 MATERIALS SCIENCE↗

Velocity structure and evolution of the moon

Seismic data from the Apollo Passive Seismic Network stations are analyzed to determine the velocity structure and to infer the composition and physical properties of the lunar interior. Data from artificial impacts (SIBV booster and LM-ascent stage) cover a distance range of 9 to 1750 km. Travel times and amplitudes, as well as theoretical seismograms, are used to derive a velocity model for the outer 150 km of the moon. The P-wave velocity model confirms an earlier report of a lunar crust in the eastern part of Oceanus Procellarum. The crust is about 60 km thick and may consist of two layers in the mare regions. Possible values for the P-wave velocity in the uppermost mantle are between 7.6 and 9.0 km/sec. The 9 km/sec velocity represents either a localized heterogeneous unit, or a thin layer less than about 40 km in thickness. The elastic properties of the deep interior, as inferred from the seismograms of natural events (meteoroid impacts and moonquakes) occurring at great distances, indicate that there is an increase in attenuation and a possible decrease of velocity at depths below about 1000 km.

Toksoz, M. N.↗

Porous structure and mechanical strength of cement-lime pastes during setting

The acceleration of a cement paste setting as a result of lime addition may be shown from isothermal calorimetry measurements. We investigated the underlying mechanisms through two techniques that provide information on porous structure (using Nuclear Magnetic Resonance) and mechanical properties (elastic modulus measured by rheometry). The correlation of the two sets of results on a cement paste clearly reveals the successive steps of setting, and particularly highlights the so-called induction period. We show that this induction period disappears in the presence of lime, leading to an acceleration of the setting. We also show that beyond some critical concentration of added lime the acceleration of setting is negligible.

36 MATERIALS SCIENCE↗

Step-Cycle Mechanical Processing of Gels of sPP-b-EPR-b-sPP Triblock Copolymer in Mineral Oil

Gels of syndiotactic polypropylene-b-ethylene-propylene-rubber-b-syndiotactic polypropylene (sPP-EPR-sPP) were prepared by dissolving {approx}6 wt % of the triblock copolymer in mineral oil at 170 C and then cooling to room temperature in several steps to crystallize the sPP block. The gel was subjected to step-cycle processing by first extending it to a given maximum tensile strain, followed by decreasing the load to zero. The cycle was then repeated to a higher maximum strain and so on until the sample either failed or it reached an ultimate predetermined strain. The true stress and true strain {var_epsilon}{sub H} during each cycle were recorded, including the true strain at zero load {var_epsilon}{sub H,p} after each cycle that resulted from the plastic deformation of the sPP crystals in the gel. The initial Young's modulus E{sub init} and maximum tangent modulus E{sub max} in each cycle undergo dramatic changes as a function of {var_epsilon}{sub H,p}, with Einit decreasing for {var_epsilon}{sub H,p} {le} 0.1 and then increasing slowly as {var_epsilon}{sub H,p} increases to 1 while E{sub max} increases rapidly over the entire range of {var_epsilon}{sub H,p}, resulting in a ratio of E{sub max}/E{sub init} > 1000 at the highest maximum (nominal) strain of 20. On the basis of small-angle X-ray scattering patterns from the deformed and relaxed gels, as well as on previous results on deformation of semicrystalline random copolymers by Strobl and co-workers, we propose that the initial decrease in Einit with {var_epsilon}{sub H,p} is due to a breakup of the network of the original sPP crystal lamellae while the increase in E{sub max} with {var_epsilon}{sub H,p} is caused by the conversion of the sPP lamellae into fibrils of an aspect ratio that increases with further plastic deformation. The gel elastic properties can be understood as those of a short fiber composite with a highly deformable matrix. At zero stress the random copolymer midblock chains that connect the fibrils cause these to make all angles to the tensile axis (low E{sub init}) while at the maximum strain the stiff crystalline sPP fibrils align with the tensile axis producing a strong, relatively stiff gel.

36 MATERIALS SCIENCE↗

Synchrotron x-ray diffraction measurements of strain in metallic nanoparticles with oxide shells.

We describe synchrotron x-ray diffraction measurements of strain in Cu and Pd metal nanoparticles (1.7-40 nm diameter) both with an air-formed oxide shell and after reduction of the oxide by treatment in a hydrogen-containing atmosphere. Oxide removal is evident from x-ray diffraction (for Cu) and x-ray absorption spectroscopy (for Pd). A simple model that uses bulk elastic properties is applied to each system. In the Pd case the model predictions agree well with the experiment. For Cu the observed strains are much smaller than predicted. This discrepancy is attributed to (a) the presence of multiple grains within the Cu particles and (b) the incoherency of the oxide with the metal core.

43 PARTICLE ACCELERATORS↗

The elastic and thermoelectric properties of the Zintl compound Ca{sub 5}Al{sub 2}Sb{sub 6} under high pressure

The elastic and thermoelectric properties of Ca{sub 5}Al{sub 2}Sb{sub 6} under pressure are studied using ab initio calculation and semiclassical Boltzmann theory. The calculated elastic constants and minimum thermal conductivity indicate that Ca{sub 5}Al{sub 2}Sb{sub 6} exhibits an anisotropic structure and high thermoelectric performance. The size of the band gap shows a nonlinear change with increasing pressure. Based on the electronic structure, the calculated thermoelectric parameters show that the Seebeck coefficient has no obvious change under pressure, whereas the electrical conductivity improves with increasing pressure. Therefore, the power factor increases at an appropriate pressure of P = 2.6 GPa. P-type doping of Ca{sub 5}Al{sub 2}Sb{sub 6} may achieve better thermoelectric performance than n-type doping, in agreement with experiment. The anisotropic thermoelectric properties of Ca{sub 5}Al{sub 2}Sb{sub 6} indicate that the thermoelectric performance along the z-direction is superior to other directions. This is attributed to the combination of the large dispersion and high band degeneracy along the Γ-Z direction in the band structure.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Manufacturing and Flexural Characterization of Infusion-Reacted Thermoplastic Wind Turbine Blade Subcomponents

Reactive thermoplastics are advantageous for wind turbine blades because they are recyclable at end of life, have reduced manufacturing costs, and enable thermal joining and shaping. However, there are challenges with manufacturing wind components from these new materials. This work outlines the development of manufacturing processes for a thick glass fiber-reinforced acrylic thermoplastic resin wind turbine blade spar cap, with consideration given to effects of the exothermic curing reaction on thick composite parts. Comparative elastic properties of these infusible thermoplastic materials with epoxy thermoset materials, as well as thermoplastic coupon components, are also included. Based on the results of this study it is concluded that the thermoplastic resin system is a viable candidate for the manufacturing of wind turbine blades using vacuum-assisted resin transfer molding. Significant gains in energy savings are realized avoiding heated molds, ability for recycling, and providing an opportunity for utilizing thermal welding.

17 WIND ENERGY↗

Anomalies in the Young modulus at structural phase transitions in rare-earth cobaltites RBaCo{sub 4}O{sub 7} (R = Y, Tm-Lu)

The elastic properties of rare-earth cobaltites RBaCo{sub 4}O{sub 7} (R = Y, Tm-Lu) have been experimentally studied in the temperature range of 80-300 K. The strong softening of the Young modulus {Delta}E(T)/E{sub 0} Almost-Equal-To -(0.1-0.2) of cobaltites with Lu and Yb ions has been revealed, which is due to the instability of the crystal structure upon cooling and is accompanied by an inverse jump at the second-order structural phase transition. The softening of the Young modulus and the jump at the phase transition decrease by an order of magnitude and the transition temperature T{sub s} and hysteresis {Delta}T{sub s} increase from a compound with Lu to that with Tm. A large softening of the Young modulus at the structural transition in Lu- and Yb cobaltites indicates that the corresponding elastic constant goes to zero, whereas this constant in Tm cobaltite is not a 'soft' mode of the phase transition. It has been found that the structural phase transition in Lu- and Yb cobaltites is accompanied by a large absorption maximum at the phase transition point and an additional maximum in the low-temperature phase and absorption anomalies in Tm cobaltite is an order of magnitude smaller.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

WE-D-210-04: Radiation-Induced Polymerization of Ultrasound Contrast Agents in View of Non-Invasive Dosimetry in External Beam Radiation Therapy

Purpose: Ultrasound contrast agents (UCA’s) based on gas-filled microbubbles encapsulated by an amphiphilic shell are well established as safe and effective echo-enhancers in diagnostic imaging. In view of an alternative application of UCA’s, we investigated the use of targeted microbubbles as radiation sensors for external beam radiation therapy. As radiation induces permanent changes in the microbubble’s physico-chemical properties, a robust measure of these changes can provide a direct or indirect estimate of the applied radiation dose. For instance, by analyzing the ultrasonic dispersion characteristics of microbubble distributions before and after radiation treatment, an estimate of the radiation dose at the location of the irradiated volume can be made. To increase the radiation sensitivity of microbubbles, polymerizable diacetylene molecules can be incorporated into the shell. This study focuses on characterizing the acoustic response and quantifying the chemical modifications as a function of radiation dose. Methods: Lipid/diacetylene microbubbles were irradiated with a 6 MV photon beam using dose levels in the range of 0–150 Gy. The acoustic response of the microbubbles was monitored by ultrasonic through-transmission measurements in the range of 500 kHz to 20 MHz, thereby providing the dispersion relations of the phase velocity, attenuation and nonlinear coefficient. In addition, the radiation-induced chemical modifications were quantified using UV-VIS spectroscopy. Results: UV-VIS spectroscopy measurements indicate that ionizing radiation induces the polymerization of diacetylenes incorporated in the microbubble shell. The polymer yield strongly depends on the shell composition and the radiation-dose. The acoustic response is inherently related to the visco-elastic properties of the shell and is strongly influenced by the shell composition and the physico-chemical changes in the environment. Conclusion: Diacetylene-containing microbubbles are polymerizable under influence of ionizing radiation and are a promising design concept within the development of a novel non-invasive in-vivo radiation dosimeter for external beam radiation therapy. This work was funded by the Research Foundation - Flanders (FWO)

60 APPLIED LIFE SCIENCES↗

Self-consistent clustering analysis: an efficient multiscale scheme for inelastic heterogeneous materials

A predictive computational theory is shown for modeling complex, hierarchical materials ranging from metal alloys to polymer nanocomposites. The theory can capture complex mechanisms such as plasticity and failure that span across multiple length scales. This general multiscale material modeling theory relies on sound principles of mathematics and mechanics, and a cutting-edge reduced order modeling method named self-consistent clustering analysis (SCA) [Zeliang Liu, M.A. Bessa, Wing Kam Liu, “Self-consistent clustering analysis: An efficient multi-scale scheme for inelastic heterogeneous materials,” Comput. Methods Appl. Mech. Engrg. 306 (2016) 319–341]. SCA reduces by several orders of magnitude the computational cost of micromechanical and concurrent multiscale simulations, while retaining the microstructure information. This remarkable increase in efficiency is achieved with a data-driven clustering method. Computationally expensive operations are performed in the so-called offline stage, where degrees of freedom (DOFs) are agglomerated into clusters. The interaction tensor of these clusters is computed. In the online or predictive stage, the Lippmann-Schwinger integral equation is solved cluster-wise using a self-consistent scheme to ensure solution accuracy and avoid path dependence. To construct a concurrent multiscale model, this scheme is applied at each material point in a macroscale structure, replacing a conventional constitutive model with the average response computed from the microscale model using just the SCA online stage. A regularized damage theory is incorporated in the microscale that avoids the mesh and RVE size dependence that commonly plagues microscale damage calculations. The SCA method is illustrated with two cases: a carbon fiber reinforced polymer (CFRP) structure with the concurrent multiscale model and an application to fatigue prediction for additively manufactured metals. For the CFRP problem, a speed up estimated to be about 43,000 is achieved by using the SCA method, as opposed to FE2, enabling the solution of an otherwise computationally intractable problem. The second example uses a crystal plasticity constitutive law and computes the fatigue potency of extrinsic microscale features such as voids. This shows that local stress and strain are capture sufficiently well by SCA. This model has been incorporated in a process-structure-properties prediction framework for process design in additive manufacturing.

Liu, Z.↗

Coherent spectroscopy of Mandelstam-Brillouin scattering in spatially inhomogeneous media

Mandelstam-Brillouin (MB) steady-state scattering in an elastic medium with a dense local zone inhomogeneity is considered in the 1D approximation. It is shown that for a certain size of inhomogeneity, the scattered radiation spectrum contains individual resonances whose frequencies depend on the elastic properties of microscopic inclusions. Experiments were performed using coherent four-photon scattering spectroscopy in the range 0-1 cm{sup -1} with a resolution of 0.06 cm{sup -1} in specially processed distilled water and in an aqueous solution of {alpha}-chymotrypsin albumin. In both media, the presence of MB resonances displaced is detected relative to the water resonance ( Almost-Equal-To 0.25 cm{sup -1}) in different directions and corresponding to different types of microinclusions.

60 APPLIED LIFE SCIENCES↗