Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “ELASTIC MODULUS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Uncertainty Quantification of Monolithic Tungsten Target Block Fatigue

The current STS spallation target design consists of 21 water cooled, tantalum clad, monolithic tungsten blocks. The target wheel assembly rotates such that each target block receives a direct proton pulse every 1.4 seconds (21 blocks / 15 Hz pulses). The quasi-steady heating induced by the repetitive beam pulses creates a significant mean stress distribution in the target. On top of this, the rapid energy deposition from a proton pulse induces dynamic stress waves that are of the same order of magnitude as the mean stresses. Over the design goal of 5,000 operational hours per year for a decade, each target must withstand over 130 million repetitions of these dynamic stress events. The fatigue life prediction of the target blocks is a complex sequence of simulations that depend upon a set of input parameters. For the tungsten block, the end goal is the fatigue factor-of-safety (FOS). This study documents a new structural analysis routine using software available to U.S. national laboratories (e.g. CUBIT, Sierra Multiphysics, Dakota) that enables more rapid target fatigue analysis. The increased throughput is amenable to parameter sensitivity and uncertainty quantification (UQ) studies. A set of input parameters (ultimate strength, fatigue strength, density, elastic modulus, Poisson’s ratio, thermal conductivity, coefficient of thermal expansion, specific heat, flow rate) with expected ranges are documented based on literature data, recent experimental testing, and engineering judgement. UQ bounds the resulting fatigue FOS at [0.5, 3.4] using epistemic interval analysis. These bounds are expected to be wider due to model effects (discretization) and beam effects (focus, offset) that were not included. Parameter sensitivity underscores the importance of ultimate strength and fatigue strength of irradiated tungsten on the fatigue calculations.

43 PARTICLE ACCELERATORS↗

Additively manufacturing high-temperature aluminum alloy for automotive engine pistons

The purpose of the project was to evaluate DuAlumin-3D, an ORNL designed Al alloy, for additive manufacturing of high-performance automotive components. The project consisted of additively manufacturing a cylindrical block of representative material which was then heat treated before machining into test coupons. Testing included tensile tests as a function of temperature, high-cycle fatigue testing as a function of temperature, density and elastic modulus measurements, and thermophysical property measurements. Fractography was also performed on failed high-cycle fatigue specimens. The results were compared against benchmark AM Al alloys and current high-performance conventionally manufactured alloys. Overall, the DuAlumin-3D material outperformed the incumbent materials in mechanical properties, especially at elevated temperatures, while maintaining broadly similar thermophysical properties. The results of this study support further maturation of the material for additive manufacturing of high-performance automotive components.

36 MATERIALS SCIENCE↗

Understanding Geometry and Microstructure Interactions In LPBF By Linking Lab Scale Studies To Real Part Case Examples

The mechanical properties derived from simple tensile tests are uniquely important in the design and qualification of load bearing metallic components. The tensile properties in standards for wrought metallic materials are generally accessible for design and simulation engineers, but this is not the case for additively manufactured metals. This work investigates the influence of tensile specimen geometry on the mechanical properties of laser powder bed fusion (LPBF) additively manufactured Ti-6Al-4V, particularly in relation to properties measured from specimens excised from an exemplar part. A comprehensive analysis was conducted across various specimen geometries, considering factors such as thermal history, cross-sectional area, shape, and surface roughness. Key findings reveal that sample size, particularly cross-sectional area, significantly affects reported tensile properties, with ASTM E8 flat and round specimens exhibiting differences in elastic modulus (13%), yield strength (17%), ultimate tensile strength (UTS) (14%), and elongation to failure (11%). Additionally, surface roughness was found to have a limited impact on ASTM round geometries, but it becomes critical in thin-walled and small high-throughput samples. The ASTM flat samples closely matched the properties of samples excised from the exemplar part, underscoring the necessity of testing witness samples that accurately represent end-use conditions. Furthermore, mechanical properties of samples built within the stitch zone of the exemplar part demonstrated reduced ductility, highlighting the importance of laser alignment and qualification in multi-laser additive manufacturing processes. Overall, this study emphasizes the need for careful consideration of specimen geometry and testing conditions to ensure accurate reporting of mechanical properties in LPBF Ti-6Al-4V.

36 MATERIALS SCIENCE↗

UHT-CAMANCHE: Ultra-High Temperature Ceramic Additively Manufactured Compact Heat Exchangers

The conceptual basis for this project is the convergence of advanced ultra-high temperature ceramic materials and additive manufacturing technologies to produce compact ceramic heat exchangers with complex internal flow path geometries. Task areas were broadly divided into materials and manufacturing development, heat exchanger design, component testing, and techno-economic analysis. Technical challenges included the design and commissioning of new test facilities, improving feature resolution and deposition rate of ceramic additive manufacturing techniques, establishing process-structure-property relationships in additively manufactured ultra-high temperature ceramics, and assessing high temperature materials compatibility in CO 2 environments. The primary candidate material evaluated in this work is a composite comprising zirconium diboride (ZrB2) with 30 vol. % silicon carbide (SiC) which was selected based on its desirable combination of high temperature mechanical properties, high thermal and electrical conductivities, and oxidation resistance. High solids loaded ZrB2-SiC pastes suitable for extrusion-based additive manufacturing were developed for the first time as part of this work. Materials compatibility studies indicate this material oxidizes in CO 2 to form a protective borosilicate scale which transforms to pure silica above 1000°C. Parts made by additive manufacturing displayed enlarged grain sizes produced by pressureless sintering as compared to hot-press sintering. Increases in microstructural coarseness have outsized effect on oxidation performance up to 1400°C due to incomplete oxidation of coarse large diameter SiC particles resulting in lower amounts of silica that apparently inhibit protective scale formation. Additive manufacturing as a forming technique did not appear to significantly affect thermal conductivity, hardness, or elastic modulus, though flexural strength was reduced by half or more as compared to traditionally hot-pressed materials. This effect was attributed to the presence of strength-limiting flaws (ca. 40 microns in size) originating from extrudate inhomogeneities that could potentially be eliminated with further process improvements. Attempts to attain economies of scale for production of multi-kilowatt scale heat exchangers by ceramic additive manufacturing proved difficult. Lack of automation and a modest extrusion rate while retaining fine feature resolution made the overall process labor intensive and limited experimental throughput. A number of full-scale components were taken through post-process heat treatments including drying, binder burnout, and sintering; however, none survived without significant flaws or cracks. Therefore, no operational data from a newly installed heat exchanger test loop were able to be obtained during the performance period. Continued research and development is recommended to improve economic feasibility of ceramic additive manufacturing by standardizing the use of advanced sensors, artificial intelligence, and automation tools to reduce associated labor costs and accelerate production rates. The materials and manufacturing techniques demonstrated in this work are likely to find applications in defense and energy applications.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Bayesian Calibration of Nuclear Graphite Property Models Accounting for Model Inadequacy and Impacts on Component Performance

Nuclear-grade structural graphite is extensively utilized in the core designs of various advanced nuclear reactors. In the reactor environment, graphite is subjected to prolonged exposure to extreme conditions, including high temperatures, radiation, and potentially molten salt and oxygen. Such exposure can induce several degradation mechanisms in graphite, including nonuniform volumetric strains caused by irradiation and thermal expansion, leading to stresses that may compromise the performance of graphite components. Assessing component integrity requires accurate models of graphite's thermomechanical response. This report documents the Bayesian calibration of thermomechanical properties for nuclear-grade graphite and their application to graphite component modeling and simulation using the Grizzly code. As part of this work, uncertainty-quantified models were developed for the elastic modulus, coefficient of thermal expansion, irradiation-induced dimensional change, and irradiation-induced creep for graphite grades IG-110, NBG-18, NBG-17, PCEA, and 2114. Using a hierarchical Bayesian approach, multiple experimental data sources were combined to develop Gaussian process models for the properties. Using the Kennedy O'Hagan framework, the uncertainties due to inadequacies in the model and the inherent spread in the experimental data were quantified for three different models. These uncertainty-quantified models, with a model-form correction, were subsequently applied to a coupled-physics simulation of representative graphite components, revealing that the uncertainties have a large impact on the components' deformation.

36 - MATERIALS SCIENCE↗

Fracture Analysis of Cohesive Zone Models for Modeling Residual Stress Induced Delamination in Composite Structures

A fracture study of coupon-scale composite cylinders with embedded defects was conducted with an objective to assess and validate a modeling approach using two available cohesive material models. The study included experimental and simulation evaluations of initiation of crack growth and progression. Interrupted thermal experiments used acoustic emissions monitoring to identify the onset of crack progression during each cooling interval and ultrasonic scanning provided images of defect growth. Verification, validation, and uncertainty quantification (VVUQ) processes were performed in the assessment of the simulation predicted temperature at which crack propagation begins (quantity of interest). The Sobol sensitivity analysis identified the hoop direction elastic modulus in the carbon fiber reinforced polymer (CFRP) plies as the most influential parameter for simulations using both cohesive models, accounting for at least 70% of the variation in the temperature at crack propagation. The UQ temperature range for the Tvergaard-Hutchinson model was higher (more conservative) than the experimental acoustic measurement indicators of crack progression, while the temperature range for the Thouless-Parmigiani model enveloped the experimental data points for the primary defect size of 0.75 x 1 in. The simulations could not capture the stable crack growth indicated in the experiments. This is likely due to the models’ inability to represent anisotropic fracture toughness attributed to the structure of the orthotropic fiber weave in a woven composite laminate.

42 ENGINEERING↗

Carbon Characterization Laboratory Report

The newly completed Idaho National Laboratory (INL) Carbon Characterization Laboratory (CCL) is located in Lab-C20 of the Idaho National Laboratory Research Center. This laboratory was established under the Next Generation Nuclear Plant (NGNP) Project to support graphite research and development activities. The CCL is designed to characterize and test carbon-based materials such as graphite, carbon-carbon composites, and silicon-carbide composite materials. The laboratory is fully prepared to measure material properties for nonirradiated carbon-based materials. Plans to establish the laboratory as a radiological facility within the next year are definitive. This laboratory will be modified to accommodate irradiated materials, after which it can be used to perform material property measurements on both irradiated and nonirradiated carbon-based material. Instruments, fixtures, and methods are in place for preirradiation measurements of bulk density, thermal diffusivity, coefficient of thermal expansion, elastic modulus, Young’s modulus, Shear modulus, Poisson ratio, and electrical resistivity. The measurement protocol consists of functional validation, calibration, and automated data acquisition.

36 MATERIALS SCIENCE↗

Mechanical Testing of TR-55 Rubber Thermally Aged Under Tensile Strain

TR-55 rubber specimens were previously subjected to an aging process consisting of the application of a tensile strain of approximately 67%, 100%, 133%, or 167% elongation for 4, 8, 12, or 16 h at either 250 C or room temperature. Control specimens at the same temperatures/durations were not subjected to tensile strain. The specimens were allowed to recover at room temperature without external stimuli for over 100 days before tensile testing. A single dog bone was cut from each specimen and a stress-strain curve was obtained. The elastic modulus of each specimen was calculated. Specimens aged under tensile strain exhibited rubber-like behavior dependent on the aging elongation and duration. This behavior was not evident in the unstrained controls. For the unstrained controls, exposure to 250 C resulted in an increase in modulus relative to the unheated material independent of the heating duration. The tensile strain applied during the aging process caused a reduction in modulus relative to the controls; lower moduli were observed for the shorter aging durations. Slippage of the specimens in the grips prevented determination of ultimate strength, as all specimens either slipped completely out of the grip before failure or failed at the original grip edge after slipping.

36 MATERIALS SCIENCE↗

Property and lifetime prediction in aged U-Nb alloys: a statistical assessment

This study was undertaken to better model the aging response of U-Nb alloys, particularly to predict properties and their scatter bands, from which lifetimes and their uncertainties can be evaluated. Predictive models of the aging time- and temperature-dependencies of seven age-sensitive properties were developed for nonbanded U-5.6 wt% Nb and U-7.7 wt% Nb alloys. These properties were total and uniform plastic tensile elongation to failure; first-yield, second-yield, and ultimate tensile strengths; first-yield elastic modulus; and Vickers microhardness. A more systematic and statistically aware kinetics modeling approach than employed previously gave reasonable models fits to accelerated aging property data in nonbanded U-5.6Nb and U-7.7Nb, and useful predictions for most of the properties studied. With minor modifications, the U-5.6Nb model was extended to banded U-6Nb. This modeling approach shared many of the key assumptions of the previous approach, including the assumption of Arrhenius behavior and the use of three adjustable parameters. Initial data returns from long-term aging experiments were used to validate the fitted models, a new feature to this study. The apparent activation energies of aging for the property of greatest interest, total elongation, were 32 kcal/mol for U-5.6Nb and 39 kcal/mol for U-7.7Nb, respectively; those for the other properties spanned 14–51 kcal/mol. Comparing the goodness of the model fits for the seven properties, the best fits were obtained for second-yield strength and hardness, the first-yield modulus fit the least well, and the other properties’ fits were in between. The U-5.6Nb models are more robust and therefore are expected to have better predictive power than those of U-7.7Nb, especially at the lower aging temperatures of interest. Model extrapolations to longer times (up to 5 years) and lower temperatures (as low as 40ºC) than those used for the model fitting agreed well with most of the validation data gathered for both nonbanded alloys, as well as banded U-6Nb, giving provisional validation of the fitted models. Property predictions for planned or already pending validation experiments are also provided. With a view towards enabling future modeling efforts, this report tabulates all replicate tensile properties and complete hardness scan data used for both model fitting and validation. For surveillance purposes, the properties most practically amenable to detecting the onset of aging at the earliest times are first-yield strength and second-yield strength. Even at aging temperatures as high as 60ºC, the minimum lifetimes from this present study are beyond 100 years, giving no cause for concern, if the previously developed failure criterion based on uniaxial tensile elongation (with its caveats) is accepted.

36 MATERIALS SCIENCE↗

A study of the relationship between lithium ion transport and structure and dynamic behavior in polyethylene oxide-melt/LiClO 4 battery electrolytes.

An experimental study of the canonical SPE (“solid” polymer electrolyte) for rechargeable “rocking chair” lithium/polymer batteries, viz. LiClO4 dissolved in molten poly(ethylene oxide) (PEO), was carried out under DOE grant FG02-04ER15573. In this study, an improved understanding was obtained of the relationship between lithium ion transport and polymer behavior in these SPEs. Among other applications, these sturdy temperature-tolerant and powerful light-weight batteries would be used in electric and electric-hybrid vehicles to reduce greenhouse gas emissions, to store unused electrical energy for peak demand loads and as compact, light-weight energy sources for aircraft and spacecraft. During the period of the grant, the American/Canadian partnership company “Avestor” fabricated and successfully demonstrated a telecommunications application of shoe-box sized batteries and representatives from Avestor visited our research lab at UNLV. They found our results interesting and relevant to their work and invited us to visit Avestor and present a talk about our efforts at UNLV. Unfortunately Avestor (who was scheduled to build a battery production facility in Apex, Nevada just North of Las Vegas) folded before the visit could be made. In the grant work, two well characterized PEO samples having molar masses distinctly below and distinctly above the melt entanglement molar mass were used and three laser light scattering techniques employed as the principal noninvasive methods of investigating liquid poly(ethylene oxide) (PEO)/LiClO4 SPEs. These investigations considered the effects of temperature, dissolved salt concentration and scattering wavevector on SPE behavior. Classical or “static” light scattering and the dynamic light scattering techniques of photon correlation spectroscopy (PCS) and Fabry-Perot interferometry (FPI) were used to study SPE static, low frequency and high frequency dynamic behaviors, respectively. Static measurements provided information about system structure while low frequency results provided information about slower (0.1-10s) more global behavior and high frequency results provided information about faster (~10-11s) more local behavior. In addition, viscometry, rheometry and thermal analysis provided vital complementary results. It was found that liquid PEO/lithium salt solutions for both PEO molar masses are random transient physical networks with measureable network and intra-network relaxation times using PCS and FPI. Thus novel and informative results addressing both large scale and small scale behavior were obtained. For example, the high sensitivity of liquid PEO electrolytes to the presence of presumably undesirable trace amounts of residual water and/or methanol was clearly evident in PCS measurements. In “unentangled” melts the activation energies for diffusive relaxation in liquid PEO/lithium salt electrolytes measured using PCS and the activation energies for viscous flow in these systems determined by viscometry were identical while thermal analyses detected no phase transitions for these systems. These results reinforced an earlier assumption that the liquid PEO/LiClO4 system is a liquid polymer “bimorph” (to our knowledge the first of its kind to be reported) with the network comprising one form of the polymer while the second form corresponds to that of a viscous damping liquid. At a given temperature, FPI characteristic relaxation times for local, between-chain motions were consistent with PCS results so that increases with increasing salt concentration were accompanied by increases in the elastic modulus and corresponding increases in system stiffness. Note that corresponding decreases in polymer segmental mobility are accompanied by reduced ion diffusivity. For entangled melts, PCS network relaxations were again observed and these systems were also considered to be bimorphs even though diffusion activation energies were distinctly larger than viscous flow activation energies - a difference attributed to the effects of entanglement. Moreover, SLS measurements revealed entangled melts to be “percolation gels” with a measured fractal dimension of about 2 and static correlation lengths that increased gradually from about 500 nm to about 700 nm with increasing salt concentration. Meanwhile, rheological measurements found these polymer/salt melts to behave simply as liquids. FPI measurements have not yet been made on these entangled PEO melts.

25 ENERGY STORAGE↗

Co-Continuous Phase Nanofiber Composites

We report on the development of a co-continuous phase composite with a polyacrylonitrile (PAN nanofiber network integrated into an acrylonitrile-butadiene-styrene (ABS) matrix that offers improved mechanical strength. Homogeneous dispersion of nanomaterials in a matrix can be challenging and typically involves mechanical mixing or chemical modification. This work overcomes this obstacle by taking an inverse approach in that a nanoscale network is synthesized then infiltrated with polymer instead of attempting to disperse the nanomaterial in the polymer. This not only enables excellent homogeneity but also allows the nanoscale phase to be continuous throughout the composite. Here, PAN is electrospun to form a random network of nanofibers having diameters of roughly 200 nm, which is then infiltrated with ABS using solution processing. By optimizing the heat treatments and ABS concentrations, the tensile strength and elastic modulus were improved by 208% and 313%, respectively, as compared to the bare PAN nanofibers. Since there has been significant previous research efforts on electrospinning polymers, many different nanofiber and polymer systems can be made into composites using the methodology established in this work. Therefore, this research offers a new route to create a co-continuous composite with the aim to replace some existing fiber reinforced composites.

Bowland, Christopher↗

Impacts of Curing-Induced Phase Segregation in Silicon Nanoparticle-Based Electrodes

We report the investigation of silicon nanoparticle composite anodes for Li-ion batteries, using a combination of two nm-scale atomic force microscopy-based techniques: scanning spreading resistance microscopy for electrical conduction mapping and contact resonance and force volume for elastic modulus mapping, along with scanning electron microscopy-based energy dispersion spectroscopy, nanoindentation, and electrochemical analysis. Thermally curing the composite anode—made of polyethylene oxide-treated Si nanoparticles, carbon black, and polyimide binder—reportedly improves the anode electrochemical performance significantly. This work demonstrates phase segregation resulting from thermal curing, where alternating bands of carbon and silicon active material are observed. This electrode morphology is retained after extensive cycling, where the electrical conduction of the carbon-rich bands remains relatively unchanged, but the mechanical modulus of the bands decreases distinctly. These electrical and mechanical factors may contribute to performance improvement, with carbon bands serving as a mechanical buffer for Si deformation and providing electrical conduction pathways. This work motivates future efforts to engineer similar morphologies for mitigating capacity loss in silicon electrodes.

25 ENERGY STORAGE↗

Application of Multiharmonic QCM-D for Detection of Plasmin at Hydrophobic Surfaces Modified by β-Casein

Plasmin protease plays an important role in many processes in living systems, including milk. Monitoring plasmin activity is important for control of the nutritional quality of milk and other dairy products. We designed a biosensor to detect the proteolytic activity of plasmin, using multiharmonic quartz crystal microbalance with dissipation (QCM-D). The β-casein immobilized on the hydrophobic surface of 1-dodecanethiol on the AT-cut quartz crystal was used to monitor plasmin activity. We demonstrated detection of plasmin in a concentration range of 0.1–20 nM, with the limit of detection about 0.13 ± 0.01 nM. The analysis of viscoelastic properties of the β-casein layer showed rapid changes of shear elasticity modulus, μ, and coefficient of viscosity, η, at plasmin sub-nanomolar concentrations, followed by modest changes at nanomolar concentrations, indicating multilayer architecture β-casein. A comparative analysis of viscoelastic properties of β-casein layers following plasmin and trypsin cleavage showed that the higher effect of trypsin was due to larger potential cleavage sites of β-casein.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A Thermal and Nanomechanical Study of Molecular Crystals as Versatile Mocks for Pentaerythritol Tetranitrate

Pentaerythritol tetranitrate (PETN) is a commonly used high explosive (HE) in detonators. Often, surrogate or “mock” materials are used in place of HE for mechanical tests, proofing out equipment, or developing new diagnostics. However, there is no commonly accepted mock for PETN. A good mock should match at least one physical property of the target material, and ideally mimic multiple thermal and mechanical properties. Here, we investigate several molecular crystals to evaluate their efficacy in mocking PETN density, melting point, elastic modulus, hardness, plastic deformation, and fracture behavior. Materials were tested with a combination of calorimetry and nanoindentation. Two materials, 2,4,6-trifluorobenzoic acid (246 TFBA) and mesoerythritol, were downselected for detailed indentation study after the initial round of screening experiments, both were found to mimic PETN mechanical behavior quite well, 246 TFBA closer to PETN in most properties (hardness, modulus, and density) than erythritol, but erythritol having advantages in relative cost and matching the onset of yield. Depending on the desired implementation of the mock, one material may be preferred over the other, but both have potential as generic mocks for PETN. Nanoindentation is demonstrated as a versatile tool to provide rapid screening of these materials’ mechanical properties.

42 ENGINEERING↗

High-Fidelity Mock Development for the Insensitive High Explosive TATB

Due to the violent reaction potential of high explosives, in tests where a reaction is not desired, it can be safe and convenient to use an inert mock that can mimic relevant properties of the associated explosive. Use of mock materials is well-established in explosives work, but most existing mocks are generally meant to mimic only one or two properties of a given explosive, potentially failing to match the explosive in other critical ways. Recently, there has been interest in developing robust thermomechanical mocks for many common explosives. Here, eleven materials are systematically chosen and investigated as potential thermomechanical mocks for TATB, the explosive component of PBX 9502. DSC, nanoindentation, and compression testing are used to narrow down to most appropriate mocks and identify their advantages and limitations. Hardness and elastic modulus are reported for the first time for the molecular crystals iodoanthranilic acid, hexamine, melamine, and trithiolane dioxide, and the crystal structure is reported for the first time for the molecular crystals iodoanthranilic acid and iodosalicylic acid.

36 MATERIALS SCIENCE↗

Aging of Limestones and Silane–Siloxane-Based Protective Hydrophobics: The Impact of Heating–Cooling and Freeze–Thaw Cycles

Stones are traditionally used in construction and architectural applications as building elements due to their aesthetic and technical/structural performance. Like other environmental factors (rain, humidity, moisture, salt presence, biological activity, etc.), heating–cooling and freeze–thaw cycles significantly threaten the longevity of stone materials. Hence, considering the socio-economic and cultural value of stones, preventive actions such as hydrophobic coatings are applied to prevent or mitigate damage. The scope of this study is the performance assessment of limestones with different characteristics and the efficiency of various commercial silane/siloxane-based hydrophobic coatings when exposed to thermal variation and freeze–thaw. For that purpose, the standards EN 14066:2013 (determination of resistance to aging by thermal shock) and EN 12371:2010 (determination of frost resistance) were followed. Open porosity and static contact angles were estimated to assess the stone durability and water protection capabilities of the hydrophobics. Additionally, sound speed propagation velocity, quality of building material index, elastic modulus and flexural strength were measured to evaluate the variation of mechanical properties. Static contact angle revealed that the coatings maintained an efficient level of hydrophobicity even after thermal-shock and freeze–thaw weathering tests. The study also revealed a critical interaction between freeze–thaw cycles, hydrophobic coatings and structural integrity of the stones, mostly on more porous ones. When they are subjected to harsh environmental conditions, untreated porous limestones keep structural cohesion, allowing for the natural absorption and release of water during freezing and thawing. On the contrary, when limestones are treated, the hydrophobic coatings can moderately obstruct the water release due to the partial saturation of the porous framework by the products. It also probably resulted from the different mechanical behavior between the inner matrix and layer of stone coated, resulting in a premature breakout and mechanical damage of the stone.

Lisci, Carla (ORCID:000000032179130X)↗

Investigation of Bone Growth in Additive-Manufactured Pedicle Screw Implant by Using Ti-6Al-4V and Bioactive Glass Powder Composite

In this study, we optimized the geometry and composition of additive-manufactured pedicle screws. Metal powders of titanium-aluminum-vanadium (Ti-6Al-4V) were mixed with reactive glass-ceramic biomaterials of bioactive glass (BG) powders. To optimize the geometry of pedicle screws, we applied a novel numerical approach to proposing the optimal shape of the healing chamber to promote biological healing. We examined the geometry and composition effects of pedicle screw implants on the interfacial autologous bone attachment and bone graft incorporation through in vivo studies. The addition of an optimal amount of BG to Ti-6Al-4V leads to a lower elastic modulus of the ceramic-metal composite material, effectively reducing the stress-shielding effects. Pedicle screw implants with optimal shape design and made of the composite material of Ti-6Al-4V doped with BG fabricated through additive manufacturing exhibit greater osseointegration and a more rapid bone volume fraction during the fracture healing process 120 days after implantation, per in vivo studies.

stress-shielding effect↗