Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DUCTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Design and analysis of vortex generators on reengined Boeing 727-100QF center inlet S-duct by a reduced Navier-Stokes code

This paper describes the application of a three dimensional reduced Navier-Stokes code to perform design and analysis of vortex generators on a reengined Boeing 727-100QF center engine inlet S duct. This computer code with vortex generators modeling is shown to be cost-effective, accurate and easy to use to design the optimal vortex generators installed on a S-duct, predict its aerodynamic performance and provide the detailed flow field information.

Huang, Pao S.↗

CFD mixing analysis of jets injected from straight and slanted slots into confined crossflow in rectangular ducts

A CFD study was performed to analyze the mixing potential of opposed rows of staggered jets injected into confined crossflow in a rectangular duct. Three jet configurations were numerically tested: (1) straight (0 deg) slots; (2) perpendicular slanted (45 deg) slots angled in opposite directions on top and bottom walls; and (3) parallel slanted (45 deg) slots angled in the same direction on top and bottom walls. All three configurations were tested at slot spacing-to-duct height rations (S/H) of 0.5, 0.75, and 1.0; a jet-to-mainstream momentum flux ratio (J) of 100; and a jet-to-mainstream mass flow ratio of 0.383. Each configuration had its best mixing performance at S/H of 0.75. Asymmetric flow patterns were expected and predicted for all slanted slot configurations. The parallel slanted slot configuration was the best overall configuration at x/H of 1.0 for S/H of 0.75.

Bain, D. B.↗

Experimental study of cross-stream mixing in a rectangular duct

An experimental investigation of non-reacting cross-stream jet injection and mixing in a rectangular duct was conducted for application in a low emissions combustor. Planar digital imaging was used to measure concentration distributions in planes perpendicular to the duct axis. Mixing rate was measured for 45 deg slanted slot and round orifice injectors. Five areas of inquiry are discussed: (1) mixing improves continuously with increasing momentum-flux ratio; (2) given a momentum-flux ratio, there is an optimum, orifice spacing; (3) mixing is more dependent on injector geometry than mass flow ratio; (4) mixing is influenced by relative slot orientation; and (5) jet structure is different for round holes and slanted slots injectors. The utility of acquiring multipoint fluctuating properties of the flow field is also demonstrated.

Liscinsky, D. S.↗

Propagation Of Sound In Curved Ducts

Monograph presents concise, comprehensive summary of knowledge of propagation of acoustic waves in ducts and pipes including bends. Pulls together information from Lord Rayleigh's book Theory Of Sound, published in 1878, and from 33 papers scattered throughout various scientific journals published between 1945 and 1989. Monograph useful to scientists and engineers interested in such diverse topics as musical instruments, air-conditioning ducts, and jet engines. Material not available in current texts.

Rostafinski, Wojciech↗

Simplified Model Of Duct Flow

Simplified, lumped-parameter mathematical model of flow in duct proves useful in estimating quasi-steady inlet and outlet flows. Simulates important features of compressible or incompressible flows including aspiration, shock losses, combustion, transfers of heat, and changes in phase. Also simulates flows in straight or twisted ducts with constant or varying cross sections. In comparision with full three-dimensional, finite-difference model, requires much less computation and matched with experimental data more easily.

Simon, Wayne E.↗

Automated Alignment And Inspection Of Duct Welds

Machine vision system being developed for use in aligning ends of two round ducts before welding ends together and inspecting welded ducts for alignment after welding. System makes consistent, objective measurements quickly. Improves quality and reliability of welds, reduces need for rework, and reduces alignment and inspection time, thereby reducing cost of manufacture.

Cross, George S.↗

Experimental investigation of crossflow jet mixing in a rectangular duct

An experimental investigation of the mixing of nonreacting opposed rows of jets injected normal to a confined rectangular crossflow has been conducted. Planar Mie-scattering was used to measure the time-average concentration distribution of the jet fluid in planes perpendicular to the duct axis. The mixing effectiveness of round orifice injectors was measured as a function of orifice spacing and orifice diameter. Mixing effectiveness was determined using a spatial unmixedness parameter based on the variance of mean jet concentration distributions. Optimum mixing was obtained when the spacing-to-duct height ratio was inversely proportional to the square root of the jet-to-mainstream momentum-flux ratio. For opposed rows of round holes with centerlines inline, mixing was similar for blockages up to 75 percent. Lower levels of unmixedness were obtained as a function of downstream location when axial injection length was minimized. Mixing may be enhanced if orifice centerlines of opposed rows are staggered, but note that blockage must be less than 50 percent for this configuration.

Liscinsky, D. S.↗

Experimental study of cross flow mixing in cylindrical and rectangular ducts

An experimental investigation of non-reacting cross flow jet injection and mixing in cylindrical and rectangular ducts has been conducted with application to a low emissions combustor. Quantitative measurement of injectant concentration distributions perpendicular to the duct axis were obtained by planar digital imaging of the Mie-scattered light from an aerosol seed mixed with the injectant. The flowfield unmixedness was evaluated using (1) a mixing parameter derived from the ratio of the jet concentration fluctuations to the fully mixed concentration, and (2) probability density functions of the concentration distributions. Mixing rate was measured for 45 degree slant slot and round orifice injectors.

Liscinsky, D. S.↗

Some Aspects of Bifurcation Structure of Laminar Flow in Curved Ducts

A bifurcation study is made of laminar flow in curved ducts. The problem is formulated in a curvilinear coordinate system, and the governing equations, after orthogonal mapping is applied, are solved numerically by an iterative finite-difference method. Many computer runs were made with various duct cross-sections ranging from a circle to a square, to learn the transition of bifurcation structure with this change in cross-section and to reconcile the differences between them. In addition, a simpler technique is proposed to generate symmetric four-cell solutions in a circular pipe and a means is put forward to stabilize four-vortex structures in a complete cross-section.

Kao, Hsiao C.↗

Radiated noise of ducted fans

The differences in the radiated acoustic fields of ducted and unducted propellers of the same thrust operating under similar conditions are investigated. An FEM model is created for the generation, propagation, and radiation of steady, rotor alone noise and exit guide vane interaction noise of a ducted fan. For a specified number of blades, angular mode harmonic, and rotor angular velocity, the acoustic field is described in a cylindrical coordinate system reduced to only the axial and radial directions. It is found that, contrary to the usual understanding of the Tyler and Sofrin (1962) result, supersonic tip speed rotor noise can be cut off if the tip Mach number is only slightly in excess of unity and if the number of blades is relatively small. If there are many blades, the fundamental angular mode number is large, and the Tyler and Sofrin result for thin annuli becomes more relevant. Shrouding of subsonic tip speed propellers is a very effective means of controlling rotor alone noise.

Eversman, Walter↗

An experimental investigation of S-duct flow control using arrays of low-profile vortex generators

An experimental investigation was undertaken to measure the effect of various configurations of low-profile vortex generator arrays on the flow in a diffusing S-duct. Three parameters that characterize the vortex generator array were systematically varied to determine their effect: (1) the vortex generator height, (2) the streamwise location of the vortex generator array, and (3) the vortex generator spacing. Each array of vortex generators tested improved total pressure recovery. The configuration employing the largest vortex generators was the most effective in reducing total pressure distortion but did not produce the greatest total pressure recovery. No configuration of vortex generators completely eliminated the flow separation that naturally occurs in the S-duct; however the extent of the separated flow region was reduced.

Reichert, B. A.↗

Experimental investigation of crossflow jet mixing in a rectangular duct

An experimental investigation of the mixing of nonreacting opposed rows of jets injected normal to a confined rectangular crossflow has been conducted. Planar Mie-scattering was used to measure the time-average concentration distribution of the jet fluid in planes perpendicular to the duct axis. The mixing effectiveness of round orifice injectors was measured as a function of orifice spacing and orifice diameter. Mixing effectiveness was determined using a spatial unmixedness parameter based on the variance of mean jet concentration distributions. Optimum mixing was obtained when the spacing-to-duct height ratio was inversely proportional to the square root of the jet-to-mainstream momentum-flux ratio. For opposed rows of round holes with centerlines inline, mixing was similar for blockages up to 75 percent. Lower levels of unmixedness were obtained as a function of downstream location when axial injection length was minimized. Mixing may be enhanced if orifice centerlines of opposed rows are staggered, but note that blockage must be less than 50 percent for this configuration.

Liscinsky, D. S.↗

NASA. Lewis Research Center/IFMD inlet duct and nozzle high speed validation experiments

Personnel from NASA Lewis Research Center spoke on the subject of inlet duct and nozzle high speed validation experiments to include crossing shocks and boundary layer interaction, unsteady shock/boundary layer interactions, and vortex generators. Attention was also paid to the subjects of high speed mixing and transition ducts. Specific application was made to the NASP hypermixing concepts.

Hingst, Warren↗

Design of Optimum Ducts Using an Efficient 3-D Viscous Computational Flow Analysis

Design of fluid dynamically efficient ducts is addressed through the combination of an optimization analysis with a three-dimensional viscous fluid dynamic analysis code. For efficiency, a parabolic fluid dynamic analysis was used. Since each function evaluation in an optimization analysis is a full three-dimensional viscous flow analysis requiring 200,000 grid points, it is important to use both an efficient fluid dynamic analysis and an efficient optimization technique. Three optimization techniques are evaluated on a series of test functions. The Quasi-Newton (BFGS, eta = .9) technique was selected as the preferred technique. A series of basic duct design problems are performed. On a two-parameter optimization problem, the BFGS technique is demonstrated to require half as many function evaluations as a steepest descent technique.

Madabhushi, Ravi K.↗

Preliminary Investigation of the Supersonic Flow Field Downstream of Wire-mesh Nozzles in a Constant-area Duct / Lawrence I. Gould

An investigation was conducted in a 3.4- by 3.4-inch duct to determine the characteristics of the supersonic flow downstream of four wire-mesh screen nozzles with nominal design Mach numbers in the range between 1.97 and 2.58. Two types of disturbances were observed in the flow field: a fine network of interacting expansion and compression waves which were formed immediately downstream of the screens and appeared to dissipate within 25 to 40 wave intersections; and relatively strong oblique shock waves that originated at the junctions of the screens and the walls and were reflected throughout the length of the duct. Regions of fairly uniform flow were found to exist. The total-pressure loss across the screens varied from 22 percent at Mach number 1.58 to 43 percent at Mach number 2.06.

WIND TUNNELS↗

Performance of a Blunt-lip Side Inlet with Ramp Bleed, Bypass, and a Long Constant-area Duct Ahead of the Engine : Mach Numbers 0.66 and 1.5 to 2.1

Unsteady shock-induced separation of the ramp boundary layer was reduced and stabilized more effectively by external perforations than by external or internal slots. At Mach 2.0 peak total-pressure recovery was increased from 0.802 to 0.89 and stable mass-flow range was increased 185 percent over that for the solid ramp. Peak pressure recovery occurred just before instability. The 7 and one-third-diameter duct ahead of the engine reduced large total-pressure distortions but was not as successful for small distortions as obtained with throat bleed. By removing boundary-layer air the bypass nearly recovered the total-pressure loss due to the long duct.

Allen, John L↗

Heat-transfer coefficients for air flowing in round tubes, in rectangular ducts, and around finned cylinders

Report reviews published data and presents some new data on heat transfer to air flowing in round tubes, in rectangular ducts, and around finned cylinders. The available data for heat transfer to air in straight ducts of rectangular and circular cross section have been correlated in plots of Stanton number versus Reynolds number to provide a background for the study of the data for finned cylinders. Equations are recommended for both the streamlined and turbulent regions, and data are presented for the transition region between turbulent and laminar flow. Use of hexagonal ends on round tubes causes the characteristics of laminar flow to extend to high Reynolds numbers. Average coefficients for the entire finned cylinder have been calculated from the average temperature at the base of the fins and an equation which was derived to allow for the effectiveness of the fins. The available results for each finned cylinder are correlated herein in terms of graphs of Stanton number versus Reynolds number. In general, for a given Reynolds number, the Stanton number increases with increases in both spacing and width of the fins, and is apparently independent of cylinder diameter and temperature difference. For a given coefficient of heat transfer improved baffles and rough or wavy surfaces give a substantial reduction in pumping power per unit of heat transfer surface and a somewhat smaller decrease in pressure drop. (author)

Drexel, Rober E↗

Velocity distributions on two-dimensional wing-duct inlets by conformal mapping

The conformal-mapping method of the Cartesian mapping function is applied to the determination of the velocity distribution on arbitrary two-dimensional duct-inlet shapes such as are used in wing installations. An idealized form of the actual wing-duct inlet is analyzed. The effects of leading edge stagger, inlet-velocity ratio, and section lift coefficients on the velocity distribution are included in the analysis. Numerical examples are given and, in part, compared with experimental data.

Perl, W↗