Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DATA CORRELATION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

A Report from the Thermal Science Research Center (TSRC)

A vertical flow loop was designed and assembled to determine the local (circumferential and axial) and mean wall temperature distributions for single-phase and two-phase (subcooled and saturated) downward flow in both uniformly-heated and single-side heated vertical channels. Freon-11 was used as the working fluid in order to directly relate and compare the results with a previous experimental campaign which employed this same working fluid. For a given steady-state experiment, the following parameters were held constant: (1) exit pressure, (2) inlet temperature, and (3) mass velocity. For a given configuration of the 2.2 m long cylindrical channel test section, which had a 1.2 m long heated section, the applied heat rate was varied from zero through successive quasi-steady states to a level which corresponded to localized film boiling in the test section. The measurements showed that the boiling curve changes significantly at higher mass velocities with respect to both the circumferential and axial directions. The slope of the boiling curve changes in a non-monotonic fashion with respect to the circumferential directions. The slope of the boiling curve changes in a non-monotonic fashion with respect to the circumferential direction. The measurements point to the existence of a dry-out phenomenon occurring at multiple levels of the applied heat for the single-side heated channel. In comparing the heat transfer for horizontal channel flow with a vertically downward flow, the results show that significantly lower heat transfer occurs in the horizontal flow. However, this trend reverses as both the Reynolds number and the applied heat rate increase. Both the Liu-Winterton and Shah correlations were compared with the experimental data. The Shah correlation predicted the uniformly heated tube data better. When a thermal hydraulic diameter approach was used for the single-side heated case, the data at upstream locations for Z/L less than 0.5 was bounded above by the Liu-Winterton correlation and below by the Shah correlation. At Z/L = 0.5, the Shah correlation bounded the data; and for Z/L greater than 0.5, both correlations overpredicted the data with the Shah correlation being closest to the data. The present results indicate that additional correlational development is needed. In addressing some of the advanced space thermal management objectives concerning accommodating high heat fluxes in non-uniformly heated systems, a large battery of experiments 88 have been completed where local two-dimensional wall temperature variations were measured for both single-phase and two-phase flow in a single-side heated circular tube. As noted above, the results show significant axial and circumferential variations. Accurately accounting for such variations can result in optimized future advanced space, enhanced (high heat flux) thermal management systems.

Boyd, Ronald D.↗

The Impact of Anisotropic Error Correlation Modelling

Most data assimilation systems assume isotropic forecast error correlations, but results from two dimensional Kalman Filter experiments indicate that the correlations can be far from isotropic. In this paper we use a simple two-dimensional data assimilation system, which analyses trace chemical species such as ozone, to assess different approaches to modelling the error correlations. We compare assimilation results using isotropic correlations with results obtained using different approaches to modelling anisotropic correlations: first, using correlations based on the concentrations of the trace chemicals, and secondly using an advective correlation model. We show that these relatively cheap ways of modelling anisotropic correlations give objectively better results than using isotropic correlations. We discuss the possible extension of these approaches to a full 3-D meteorological data assimilation system.

Swinbank, R.↗

Non-Gaussianity in WMAP data due to the correlation of CMB lensing potential with secondary anisotropies

We measure the skewness power spectrum of the CMB anisotropies optimized for a detection of the secondary bispectrum generated by the correlation of the CMB lensing potential with integrated Sachs-Wolfe effect and the Sunyaev-Zel'dovich effect. The covariance of our measurements is generated by Monte Carlo simulations of Gaussian CMB fields with noise properties consistent with WMAP 5-year data. When interpreting multifrequency measurements we also take into account the confusion resulting from unresolved radio point sources. We analyze Q, V and W-band WMAP 5-year raw and foreground-cleaned maps using the KQ75 mask out to l{sub max}=600. We find no significant evidence for a nonzero non-Gaussian signal from the lensing-secondary correlation in all three bands and we constrain the overall amplitude of the cross-power spectrum between CMB lensing potential and the sum of SZ and ISW fluctuations to be 0.42{+-}0.86 and 1.19{+-}0.86 in combined V and W-band raw and foreground-cleaned maps provided by the WMAP team, respectively. The point-source amplitude at the bispectrum level measured with this skewness power spectrum is higher than previous measurements of point-source non-Gaussianity. We also consider an analysis where we also account for the primordial non-Gaussianity in addition to lensing-secondary bispectrum and point sources. The focus of this paper is on secondary anisotropies. Consequently the estimator is not optimized for primordial non-Gaussianity and the limit we find on local non-Gaussianity from the foreground-cleaned V+W maps is f{sub NL}=-13{+-}62, when marginalized over point sources and lensing-ISW/SZ contributions to the total bispectrum.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Inferring Correlation Networks from Genomic Survey Data

High-throughput sequencing based techniques, such as 16S rRNA gene profiling, have the potential to elucidate the complex inner workings of natural microbial communities - be they from the world's oceans or the human gut. A key step in exploring such data is the identification of dependencies between members of these communities, which is commonly achieved by correlation analysis. However, it has been known since the days of Karl Pearson that the analysis of the type of data generated by such techniques (referred to as compositional data) can produce unreliable results since the observed data take the form of relative fractions of genes or species, rather than their absolute abundances. Using simulated and real data from the Human Microbiome Project, we show that such compositional effects can be widespread and severe: in some real data sets many of the correlations among taxa can be artifactual, and true correlations may even appear with opposite sign. Additionally, we show that community diversity is the key factor that modulates the acuteness of such compositional effects, and develop a new approach, called SparCC (available at https://bitbucket.org/yonatanf/sparcc), which is capable of estimating correlation values from compositional data. To illustrate a potential application of SparCC, we infer a rich ecological network connecting hundreds of interacting species across 18 sites on the human body. Using the SparCC network as a reference, we estimated that the standard approach yields 3 spurious species-species interactions for each true interaction and misses 60% of the true interactions in the human microbiome data, and, as predicted, most of the erroneous links are found in the samples with the lowest diversity.

59 BASIC BIOLOGICAL SCIENCES↗

Cosmological cross-correlations and nearest neighbour distributions

ABSTRACT Cross-correlations between data sets are used in many different contexts in cosmological analyses. Recently, k-nearest neighbour cumulative distribution functions (kNN-CDF) were shown to be sensitive probes of cosmological (auto) clustering. In this paper, we extend the framework of NN measurements to describe joint distributions of, and correlations between, two data sets. We describe the measurement of joint kNN-CDFs, and show that these measurements are sensitive to all possible connected N-point functions that can be defined in terms of the two data sets. We describe how the cross-correlations can be isolated by combining measurements of the joint kNN-CDFs and those measured from individual data sets. We demonstrate the application of these measurements in the context of Gaussian density fields, as well as for fully non-linear cosmological data sets. Using a Fisher analysis, we show that measurements of the halo-matter cross-correlations, as measured through NN measurements are more sensitive to the underlying cosmological parameters, compared to traditional two-point cross-correlation measurements over the same range of scales. Finally, we demonstrate how the NN cross-correlations can robustly detect cross-correlations between sparse samples – the same regime where the two-point cross-correlation measurements are dominated by noise.

79 ASTRONOMY AND ASTROPHYSICS↗

Techniques for hot structures testing

Hot structures testing have been going on since the early 1960's beginning with the Mach 6, X-15 airplane. Early hot structures test programs at NASA-Ames-Dryden focused on operational testing required to support the X-15 flight test program, and early hot structures research projects focused on developing lab test techniques to simulate flight thermal profiles. More recent efforts involved numerous large and small hot structures test programs that served to develop test methods and measurement techniques to provide data that promoted the correlation of test data with results from analytical codes. In Nov. 1988 a workshop was sponsored that focused on the correlation of hot structures test data with analysis. Limited material is drawn from the workshop and a more formal documentation is provided of topics that focus on hot structures test techniques used at NASA-Ames-Dryden. Topics covered include the data acquisition and control of testing, the quartz lamp heater systems, current strain and temperature sensors, and hot structures test techniques used to simulate the flight thermal environment in the lab.

Deangelis, V. Michael↗

The discrete correlation function: A new method for analyzing unevenly sampled variability data

A method of measuring correlation functions without interpolating in the temporal domain, the discrete correlation function, is introduced. It provides an assumption-free representation of the correlation measured in the data, and allows meaningful error estimates. This method does not produce spurious correlations at zero lag due to correlated errors. It is shown that physical interpretation of active galactic nuclei cross-correlation functions requires knowledge of the input function's fluctuation power spectrum, involves model-dependence in the form of symmetry assumptions, and must take into account intrinsic scale bias. This technique was used to find a correlation in published IUE data for NGC 4151, which indicates that the broad C IV feature emanates from a shell 15 to 75 light-days in radius, assuming spherical symmetry.

Edelson, R. A.↗

Photovoltaic inverter-based quantification of snow conditions and power loss

Snow is a significant challenge for photovoltaic (PV) systems at northern latitudes, where the pace of deployment is rapid but snow-related power losses can exceed 30% of annual production. Accurate snow-related power loss estimation methods for utility-scale sites can support snow mitigation strategies, inform resource planning and validate predictive snow-loss models. This study builds on our previous work on inverter-based detection of snow, and its implications for utility-scale power production, by validating the accuracy of our snow-loss method across different PV sites and system designs and highlighting its value in bringing greater visibility to PV plant operations in winter. Our estimation method is both novel and scalable, requiring only standard monitoring data to correlate snow-related losses with meteorological data. As demonstrated here, our validation method involved three main steps: 1) estimation of performance losses for multiple systems by comparing measured inverter data to modeled data; 2) application of a detection framework to identify which performance losses are snow-related; and 3) comparison of snow-related losses among three utility-scale sites differing in tilt angle. Results show that utility-scale systems at higher tilt angles consistently shed snow more quickly/completely than their lower-tilt counterparts. Further, monthly and seasonal snow losses are inversely and non-linearly correlated with tilt angle when normalized for cumulative snowfall. These results are consistent with the findings of previous studies and support the broad applicability of this method to fixed-tilt utility-scale PV systems around the world that routinely experience snow-related performance losses.

Cooper, Emma C. (ORCID:0000000190554098)↗

The Alcock–Paczynski effect from Lyman- α forest correlations: analysis validation with synthetic data

The three-dimensional distribution of the Ly α forest has been extensively used to constrain cosmology through measurements of the baryon acoustic oscillations (BAO) scale. However, more cosmological information could be extracted from the full shapes of the Ly α forest correlations through the Alcock–Paczynski (AP) effect. In this work, we prepare for a cosmological analysis of the full shape of the Ly α forest correlations by studying synthetic data of the extended Baryon Oscillation Spectroscopic Survey (eBOSS). We use a set of 100 eBOSS synthetic data sets in order to validate such an analysis. These mocks undergo the same analysis process as the real data. We perform a full-shape analysis on the mean of the correlation functions measured from the 100 eBOSS realizations, and find that our model of the Ly α correlations performs well on current data sets. We show that we are able to obtain an unbiased full-shape measurement of D M /D H (z eff ), where D M is the transverse comoving distance, D H is the Hubble distance, and z eff is the effective redshift of the measurement. We test the fit over a range of scales, and decide to use a minimum separation of r min = 25 h –1 Mpc. Here, we also study and discuss the impact of the main contaminants affecting Ly α forest correlations, and give recommendations on how to perform such analysis with real data. While the final eBOSS Ly α BAO analysis measured D M /D H (z eff = 2.33) with 4 per cent statistical precision, a full-shape fit of the same correlations could provide an $\sim 2~{{\ \rm per\ cent}}$ measurement.

79 ASTRONOMY AND ASTROPHYSICS↗

Exploring the limits of waveform correlation event detection as applied to three earthquake aftershock sequences.

Swarms of earthquakes and/or aftershock sequences can dramatically increase the level of seismicity in a region for a period of time lasting from days to months, depending on the swarm or sequence. Such occurrences can provide a large amount of useful information to seismologists. For those who monitor seismic events for possible nuclear explosions, however, these swarms/sequences are a nuisance. In an explosion monitoring system, each event must be treated as a possible nuclear test until it can be proven, to a high degree of confidence, not to be. Seismic events recorded by the same station with highly correlated waveforms almost certainly have a similar location and source type, so clusters of events within a swarm can quickly be identified as earthquakes. We have developed a number of tools that can be used to exploit the high degree of waveform similarity expected to be associated with swarms/sequences. Dendro Tool measures correlations between known events. The Waveform Correlation Detector is intended to act as a detector, finding events in raw data which correlate with known events. The Self Scanner is used to find all correlated segments within a raw data steam and does not require an event library. All three techniques together provide an opportunity to study the similarities of events in an aftershock sequence in different ways. To comprehensively characterize the benefits and limits of waveform correlation techniques, we studied 3 aftershock sequences, using our 3 tools, at multiple stations. We explored the effects of station distance and event magnitudes on correlation results. Lastly, we show the reduction in detection threshold and analyst workload offered by waveform correlation techniques compared to STA/LTA based detection. We analyzed 4 days of data from each aftershock sequence using all three methods. Most known events clustered in a similar manner across the toolsets. Up to 25% of catalogued events were found to be a member of a cluster. In addition, the Waveform Correlation Detector and Self Scanner identified significant numbers of new events that were not in either the EDR or regional catalogs, showing a lowering of the detection threshold. We extended our analysis to study the effect of distance on correlation results by applying the analysis tools to multiple stations along a transect of nearly constant azimuth when possible. We expected the number of events found via correlation would drop off as roughly 1/r2, where r is the distance from mainshock to station. However, we found that regional geological conditions influenced the performance of a given station more than distance. For example, for one sequence we clustered 25% of events at the nearest station to the mainshock (34 km), while our performance dropped to 2% at a station 550 km distant. However, we matched our best performance (25% clustering) at a station 198 km distant.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Determining the effects of U/Pu ratio on subsolidus phase transitions in U-Pu-Zr metallic fuel alloys

Here, ternary alloys consisting primarily of uranium, plutonium, and zirconium (U-Pu-Zr) are among the leading candidate fuel systems considered for fast spectrum nuclear reactors. Despite historical operation data from the testing of U-Pu-Zr rods in the Experimental Breeder Reactor-II, considerable uncertainty about the evolution of phases and microstructure across the ternary composition space exists. Due to sluggish kinetics and other difficulties in handling metal actinide specimens, quantitative measurements of phase-transitions in U-Pu-Zr alloys remain sparse in scientific literature, with most investigators reporting either phase-transition temperatures or phase identification data, but not both from the same specimens. The purpose of this paper is to critically compare experimental and calculated phase transition data and correlate with the microstructure and phase characterization data of as-cast and annealed U-Pu-Zr alloys. Phase transition peaks were measured using differential scanning calorimetry in the subsolidus regions (723-948 K) of three ternary U-Pu-Zr alloys with the same zirconium concentration but various U/Pu ratios. Overlapping peaks were deconvoluted using a Frazier-Suzuki peak fitting algorithm, and the critical peak temperatures and enthalpies were calculated. In general, increasing concentrations of Pu were associated with enhanced thermal stability of the body-centered cubic γ phase upon both heating and cooling. Experimental phase transition temperatures in this study tended to agree well with the predictions of the established ternary phase diagrams and other reported phase transition temperatures in literature. Additionally, the TAF-ID thermodynamic database was used to calculate a U-Pu-40 at.% Zr pseudobinary diagram as well as ternary diagrams from 773 to 973 K. The equilibrium phase transition temperatures tended to be considerably lower than measured peak temperatures upon both heating and cooling. Recommendations for improving the quality of data in future U-Pu-Zr characterization studies are also discussed.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A critical analysis of U-Pu-Zr phase transitions using calorimetric, microstructural, and phase equilibria data

Metallic fuels consisting primarily of uranium, plutonium, and zirconium (U-Pu-Zr) are a leading material candidate for fast-spectrum nuclear reactors. Early demonstration programs proved the principle of safe and efficient fast reactor operation, however there is still considerable uncertainty regarding the phase equilibria and microstructural evolution across the ternary composition space. Quantitative phase formation and identification measurements are scarce and often incomplete, with studies reporting either phase transition temperatures or phase identification data, but not both from the same specimens. In this study, we critically compared experimental and calculated phase transition data and correlated with the microstructure and phase characterization data of as-cast and annealed U-Pu-Zr alloys. Differential scanning calorimetry (DSC) was used to measure phase transitions in the subsolidus regions (723−948 K) of three ternary U-Pu-Zr alloys with similar plutonium concentrations but various U/Zr ratios. Due to sluggish kinetics and narrow ranges of phase stability, complex peaks required the use of a Frazier-Suzuki peak fitting algorithm to deconvolute and calculate transition peak temperatures and enthalpies. We also identified trends of phase transition behavior by critically comparing our DSC data with previous phase transition measurements as well as historical and calculated phase equilibrium diagrams. In conclusion, this provides a critical approach for benchmarking and assessing the quality of new U-Pu-Zr phase equilibria data prior to its incorporation into nuclear material databases.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Data Management Technology Survey and Recommendation

The Data Management Plan (DMP) document already released describes the architecture and plan for developing the data management framework needed by the Carbon Capture Simulation Initiative (CCSI) toolset. The CCSI toolset includes: experimental data, physical property methods and parameters, empirical correlations, validation data set, models, simulation inputs and outputs, reduced-order models, cost models, risk models, uncertainty estimation, etc. Each tool in the toolset requires and generates data, and the data management system organizes and stores the data. The data management framework will be driven by end-users and interact with CCSI workflow components such as Turbine. This document reports on the technology survey completed as the first step in the Data Management Plan. It also provides recommendations for a path forward based on the survey results.

97 MATHEMATICS AND COMPUTING↗

An investigation of the effect of wind cooling on photovoltaic arrays

Convective cooling of photovoltaic modules for different wind conditions, including steady state controlled testing in a solar simulator and natural test environments in a field was investigated. Analytical thermal models of different module designs were used to correlate experimental data. The applicability of existing heat transfer correlations is confirmed. Reasonable agreement is obtained by applying a power law wind profile.

Wen, L.↗

San Marco C-2 Explorer

The San Marco C-2 spacecraft will be launched no earlier than 18 February 1974 from the San Marco Range located off the coast of Kenya, Africa, by a Scout launch vehicle. The launch will be conducted by an Italian crew. The San Marco C-2 is the fourth cooperative satellite project between Italy and the United States. The purpose of the mission is to obtain measurements of the diurnal variations of the equatorial neutral atmosphere density, composition, and temperature and to use these data for correlation with AE-C (Explorer 51) data for studies of the physics and dynamics of the thermosphere. The San Marco C-2 project is a joint undertaking of the National Aeronautics and Space Administration (NASA) and the Italian Space Commission officially initiated with a Memorandum of Understanding in August of 1973. Project management responsibility for the Italian portion of the project has been assigned to the Centro Ricerche Aerospaziali (CRA) while the Goddard Space Flight Center (GSFC) has responsibility for the United States portion.

Source record↗

Correlation function studies for snow and ice

The random medium model is used to characterize snow and ice fields in the interpretation of active and passive microwave remote sensing data. A correlation function is used to describe the random permittivity fluctuations with the associated mean and variance and correlation lengths; and several samples are investigated to determine typical correlation functions for snow and ice. It is shown that correlation functions are extracted directly from appropriate ground truth data, and an exponential correlation function is observed for snow and ice with lengths corresponding to the actual size of ice particles or air bubbles. Thus, given that a medium has spatially stationary statistics and a small medium, the random medium model can interpret remote sensing data where theoretical parameters correspond to actual physical parameters of the terrain.

Vallese, F.↗

Detection of moisture and moisture related phenomena from Skylab

The author has identified the following significant results. Skylab 2 data for June 5, 1973 (Texas site) relates favorably with previously calculated aircraft data when correlating brightness temperature to soil moisture. However, more detailed work is needed to determine the corrected surface temperature. In addition, correlations between the S194 antenna temperature and soil moisture have been obtained for five sets of Skylab data. The best correlations were obtained for the surface to one inch depth in four cases and for surface to two inches depth for the fifth case. Correlation coefficients for the surface to one inch depth were -0.98, -0.95, -0.90, -0.82, and -0.80.

Eagleman, J. R.↗