Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Comparative Study”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Si II emission line diagnostics

The present study compares ratios of Si II UV emission lines in a variety of objects with computations based on recently published collisional data of Dufton and Kingston (1991). A high-quality spectrum of Alpha Tau (K5 III) obtained by Carpenter et al. (1991) is analyzed using the G270M mode of the GHRS on the HST, in addition to high-dispersion data from Skylab and IUE. Agreement between observation and theory is satisfactory for most lines. A blend with a line of Ni II accounts partially for the discrepancies and solves a problem with semiforbidden S II emission measures. Disagreement exists between certain observed flux ratios and computed values using recent atomic data for the intersystem lines. The discrepancy is most significant for Alpha Tau. The computed atomic collision strengths within the intersystem multiplet itself are argued as a possible cause of the discrepancy.

Judge, P. G.↗

A quantification of errors in surface albedo due to common assumptions

A study comparing the performance of three approaches to estimating the spectral albedo of a typical land surface is presented. The most accurate albedo estimates under all atmospheric situations are those for which the scattering properties of the atmosphere can be used. Simply utilizing the direct-to-total ratio as a weight between direct and Lambertian albedos reduced the errors in broadband albedo to less than one percent for almost all simulated atmospheric conditions.

Arduini, Robert F.↗

Numerical simulation of a subtropical squall line over the Taiwan Strait

The present 2D nonhydrostatic, time-dependent numerical cloud model, which is applied to the structure and development of a subtropical squall line observed during the Taiwan Area Mesoscale Experiment, includes (1) a parameterized ice-phase microphysical scheme, (2) longwave and shortwave radiative-transfer processes, and (3) heat and moisture fluxes from the ocean surface. A comparative study is made of the vertical transport of horizontal momentum and of the latent heat release by the simulated subtropical squall system, as well as the heat release of squall systems occurring in other geographic locations.

Tao, Wei-Kuo↗

Space dust and debris; Proceedings of the Topical Meeting of the Interdisciplinary Scientific Commission B (Meetings B2, B3, and B5) of the COSPAR 28th Plenary Meeting, The Hague, Netherlands, June 25-July 6, 1990

The present conference on space dust and debris encompasses orbital debris, in situ measurements and laboratory analysis of space-dust particles, comparative studies of comets, asteroids, and dust, the protection and maneuvering of spacecraft in space-debris environments, and the out-of-elliptic distribution of interplanetary dust derived from near-earth flux. Specific issues addressed include asteroid taxonomy, the optical properties of dust from cometary and interplanetary grains, light scattering by rough surfaces on asteroidal/lunar regoliths, and the first results of particulate impacts and foil perforations on the Long Duration Exposure Facility. Also addressed are collision probability and spacecraft disposition in the geostationary orbit, a flash on the moon caused by orbital debris, the limits of population growth in low earth orbit due to collisional cascading, and the simulation of cosmic man-made dust effects on space-vehicle elements in rocket and laboratory experiments.

Kessler, D. J.↗

Is bigger always better? An economic study of U.S. ETO vehicle architectures

This analysis, performed as part of NASA's Space Transportation Infrastructure Study, compares the cost efficiency of two candidate launch vehicle families, used in conjunction with existing expendable launch vehicles and the Shuttle, to accomplish the nation's future space missions through 2030. Missions analyzed include those identified in NASA's Civil Needs Data Base (CNDB) and Space Exploration Initiative (SEI) Option E program, as well as estimates of commercial and U.S. Department of Defense flights. A family of Shuttle-derived In-line vehicles is compared against a family designed around a vehicle optimized for large (250t) payloads. The analysis is performed within the context of an entire space transportation architecture. The goal is to determine which architecture best captures the required missions most cost-effectively. Results indicate that, for the particular mission model analyzed, neither option is clearly superior across the entire payload range. The Shuttle-derived family displays a better evolutionary path for supporting the total mission model (CNDB plus SEI missions). It also reduces earth-to-orbit (ETO) peak funding by 20 percent. The architecture incorporating the Heavy Lift ETO family minimizes SEI program cost and on-orbit operations but is subject to greater schedule risk because of the need for concurrent ETO core and engine development.

Eimers, Dan R.↗

Spaceflight training issues - Shuttle versus Station

A comparative study is made of the training practices used for Space Shuttle crews and those projected for the NASA Space Station Freedom, with a view to the relative advantages anticipated for these methods in the fields of long-duration flights, on-orbit construction techniques, on-orbit maintenance requirements, medical expertise, and remote manipulator operations. A Training Operations Subpanel has been established by NASA for the coordination of training method developments across the various elements and phases of the program.

Hughes, Frank E.↗

Role of interfacial thermal barrier in the transverse thermal conductivity of uniaxial SiC fiber-reinforced reaction bonded silicon nitride

The transverse thermal conductivity of reaction-bonded Si3N4 is significantly affected by an interfacial barrier at the interface formed with SiC reinforcing fibers. A comparative study of composites with and without reinforcing-fiber carbon coatings found the coating to reduce effective thermal conductivity by a factor of about 2; this, however, is partially due to a thermal expansion-mismatch gap between fiber and matrix. HIPing of composites with coated fibers led to an enhancement of thermal conductivity via improved interfacial thermal contact and greater grain size and crystallinity of the fibers.

Bhatt, H.↗

Polar stratospheric cloud processed air and potential vorticity in the Northern Hemisphere lower stratosphere at mid-latitudes during winter

The present study compares small-scale (less than 100 km) features in ER-2 measurements of ClO, O3, H2O, N2O, and NO(y) outside the lower stratospheric Arctic vortex of 1988-1989 with features on potential vorticity maps from ECMWF. The potential vorticity maps are obtained from T106 analyses and forecasts. Some of the plots were truncated to lower resolution (T63 or T42) which smooths out the finer-scale structure. Comparison of these lower resolution plots shows how much detail is lost by excessive smoothing. It is also evident that the forecast plots lose fine-scale structure due to dissipation in the model resulting mainly from horizontal diffusion. It is concluded that blobs of air on the maps at latitudes between the vortex edge and 25 deg N having potential vorticities characteristic of the vortex did indeed originate from the vortex, but that the real atmosphere is more sharply differentiated than the meteorological analyses, implying that the potential vorticity maps underestimate the amount of peeled-off material.

Tuck, A. F.↗

Empirical comparison of heuristic load distribution in point-to-point multicomputer networks

The study compared several load placement algorithms using instrumented programs and synthetic program models. Salient characteristics of these program traces (total computation time, total number of messages sent, and average message time) span two orders of magnitude. Load distribution algorithms determine the initial placement for processes, a precursor to the more general problem of load redistribution. It is found that desirable workload distribution strategies will place new processes globally, rather than locally, to spread processes rapidly, but that local information should be used to refine global placement.

Grunwald, Dirk C.↗

Radio occultation observations of the ionospheres of Mars and Venus

The availability of a large body of radio occultation data for the Mars and Venus ionospheres makes possible comparative studies of their structures and temporal behavior. On Venus, the nightside ionosphere is produced by the transport of ionization from the dayside, which operates at solar maximum when the ionopause is high, and impact ionization by energetic electrons, which operates at all times. On Mars, transport from the dayside would seem to be inhibited for the same reason as for Venus at solar minimum, although sufficient flux of energetic electrons is present to generate nightside ionization. The Venus ionosphere at solar minimum, and that of Mars at all times, are not in a state of diffusive equilibrium above the chemical equilibrium regions.

Kliore, Arvydas J.↗

Voyager 2 ultraviolet spectrometer solar occultations at Neptune - Constraints on the abundance of methane in the stratosphere

The study compares Voyager 2 ultraviolet spectrometer (UVS) solar occultation lightcurves at wavelengths 125-138 nm acquired during the Neptune encounter with 1D methane photochemical transport models. For the p-T models under consideration, acceptable fits to the UVS lightcurves are obtained with eddy mixing coefficient values (K sub 1/2) near the half-light altitudes of 2-15 x 10 exp 6 sq cm/s (ingress) and 4-35 x 10 exp 6 sq cm/s (egress) and lower stratospheric methane mixing ratio values of 5-100 x 10 exp -5. For the nominal p-T models and a criterion based on replicating the spacing in altitude of the 125-138 nm UVS lightcurves, K sub 1/2 values of 10 exp 7 sq cm/s (ingress) and 1-2 x 10 exp 7 sq cm/s (egress) and methane mixing ratios of about 0.0004 (ingress and egress) are indicated.

Bishop, James↗

Magellan navigation using X-band differenced Doppler during Venus mapping phase

This paper describes Magellan navigation procedures and performance during the first 1.5 years of mapping. It presents the results of studies comparing several orbit determination methods performed with and without X-band (8.4 GHz) differenced Doppler tracking data. X-band differenced Doppler has been used as a primary navigation data-type for the first time. It has been found to be a significant aid in efficiently meeting orbiter navigation requirements during the Magellan spacecraft's Venus radar-mapping phase.

Giorgini, Jon D.↗

The MICRO-BOSS scheduling system: Current status and future efforts

In this paper, a micro-opportunistic approach to factory scheduling was described that closely monitors the evolution of bottlenecks during the construction of the schedule and continuously redirects search towards the bottleneck that appears to be most critical. This approach differs from earlier opportunistic approaches, as it does not require scheduling large resource subproblems or large job subproblems before revising the current scheduling strategy. This micro-opportunistic approach was implemented in the context of the MICRO-BOSS factory scheduling system. A study comparing MICRO-BOSS against a macro-opportunistic scheduler suggests that the additional flexibility of the micro-opportunistic approach to scheduling generally yields important reductions in both tardiness and inventory. Current research efforts include: adaptation of MICRO-BOSS to deal with sequence-dependent setups and development of micro-opportunistic reactive scheduling techniques that will enable the system to patch the schedule in the presence of contingencies such as machine breakdowns, raw materials arriving late, job cancellations, etc.

Sadeh, Norman M.↗

North Massif lithologies and chemical compositions viewed from 2-4 mm particles of soil sample 76503

We identify the lithologic and compositional components of soil 76503 based on INAA of 243 2-4-mm particles and 72 thin sections from these and associated 1-2-mm particles (76502). We present a statistical distribution of the major compositional types as the first step of a detailed comparative study of the North and South Massifs. The soil sample was collected well away from any boulder and is more representative of typical North Massif material than any single large rock or boulder sample. So far, our examination of the 76503 particles has provided a better definition of precursor igneous lithologies and their petrogenetic relationships. It has enabled us to refine the nature of mixing components for the North Massif less than 1-mm fines. It has confirmed the differences in lithologies and their proportions between materials of the North and South Massifs; e.g., the North Massif is distinguished by the absence of a 72275-type KREEP component, the abundance of a highly magnesian igneous component, and the absence of certain types of melt compositions found in the South Massif samples.

Bishop, Kaylynn M.↗

Analysis of the effect of initial conditions on the initial development of a turbulent jet

The effect of the initial condition at the jet exit on the downstream evolution, particularly within the potential core length, were numerically investigated as well as with available experimental data. In order to select the most dependable computational model for the present numerical experiment, a comparative study has been performed with different turbulence models at k-epsilon level, and it was found that the k-epsilon-gammma model yields superior prediction accuracy over other conventional models. The calculated results show that the potential core length and the spreading rate the initial mixing layer are dependent on the initial length scale as well as the turbulent kinetic energy at the jet exit. Such effect of the initial length scale increases with higher initial turbulence level. An empirical parameter has been devised to collapse the calculated data of the potential core length and the spreading rate with various initial conditions onto a single curve.

Kim, Soong KI↗

Macrofossil records of West Antarctic Ice Sheet retreat during the Holocene

Marine macrofossils in emerged beaches around Antarctica represent a geochemical framework for interpreting meltwater signatures associated with variations in the adjacent ice sheet margins during the last 10,000 years. In particular, mollusc species provide ideal experimental templates for assessing hydrochemical variations in Antarctic coastal marine environments because of their excellent preservation, high abundances, circumpolar distributions, and carbonate shells, which incorporate trace elements and stable isotopes. Modern samples of the bivalve Adamussium colbecki, which were collected across a depth gradient in the vicinity of a glacial meltwater stream in West McMurdo Sound, revealed shell trace element concentrations that were significantly higher above 10 meters because of their exposure to meltwater runoff. This meltwater signature also was reflected by the shell oxygen isotopic composition, which was in equilibrium with the ambient seawater, as demonstrated by the overlap between the predicted and actual O-(delta-18)sub w values. These modern samples provide analogs for interpreting the geochemical records in their fossils, which were based solely on molluscan fossils, complement the above geochemical data by suggesting that the rate of beach emergence fluctuated around Antarctica during the mid-Holocene. Paleoenvironmental analysis of macrofossils from emerged beaches represents a new direction in Antarctic research that can be used to assess changes in the margins of the ice sheets since the Last Glacial Maximum. The resolution of these analyses will be enhanced by collaborations that are developing with scientists who are conducting comparable studies in other coastal regions around the continent.

Berkman, Paul Arthur↗

The MICRO-BOSS scheduling system: Current status and future efforts

In this paper, a micro-opportunistic approach to factory scheduling was described that closely monitors the evolution of bottlenecks during the construction of the schedule, and continuously redirects search towards the bottleneck that appears to be most critical. This approach differs from earlier opportunistic approaches, as it does not require scheduling large resource subproblems or large job subproblems before revising the current scheduling strategy. This micro-opportunistic approach was implemented in the context of the MICRO-BOSS factory scheduling system. A study comparing MICRO-BOSS against a macro-opportunistic scheduler suggests that the additional flexibility of the micro-opportunistic approach to scheduling generally yields important reductions in both tardiness and inventory.

Sadeh, Norman M.↗

Improved accuracy for finite element structural analysis via an integrated force method

A comparative study was carried out to determine the accuracy of finite element analyses based on the stiffness method, a mixed method, and the new integrated force and dual integrated force methods. The numerical results were obtained with the following software: MSC/NASTRAN and ASKA for the stiffness method; an MHOST implementation method for the mixed method; and GIFT for the integrated force methods. The results indicate that on an overall basis, the stiffness and mixed methods present some limitations. The stiffness method generally requires a large number of elements in the model to achieve acceptable accuracy. The MHOST method tends to achieve a higher degree of accuracy for course models than does the stiffness method implemented by MSC/NASTRAN and ASKA. The two integrated force methods, which bestow simultaneous emphasis on stress equilibrium and strain compatibility, yield accurate solutions with fewer elements in a model. The full potential of these new integrated force methods remains largely unexploited, and they hold the promise of spawning new finite element structural analysis tools.

Patnaik, S. N.↗