Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Combustion modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Visualization and Quantification of Wind Induced Variability in Hydrogen Clouds Following Releases of Liquid Hydrogen: Preprint

Well characterized experimental data for consequence model validation is important in progressing the use of liquid hydrogen as an energy carrier. In 2019, the Health and Safety Executive (HSE) undertook a series of liquid hydrogen dispersion and combustion experiments as a part of the Pre-normative Research into the Safe Use of Liquid Hydrogen (PRESLHY) project. In partnership between the National Renewable Energy Laboratory (NREL) and HSE, time and spatially varying hydrogen concentration measurements were made in 25 dispersion experiments and 23 congested ignition experiments associated with PRESLHY WP3 and WP5, respectively. These measurements were undertaken using the hydrogen wide area monitoring system developed by NREL. During the 23 congested ignition experiments, high variability was observed in the measured explosion severity during experiments with similar initial conditions. This led to the conclusion that wind, including localized gusts, had a large influence on the dispersion of the hydrogen, and therefore the quantity of hydrogen that was present in the congested region of the explosions. Using the hydrogen concentration measurements taken immediately prior to ignition, the hydrogen clouds were visualized in an attempt to rationalize the variability in overpressure between the tests. Gaussian process regression was applied to quantify the variability of the measured hydrogen concentrations. This analysis could also be used to guide modifications in experimental designs for future research on hydrogen combustion behavior.

HSR&D↗
DOE OSTI2022

The Modeling of the Synfuel Production Process: Process models of Fischer-Tropsch production with electricity and hydrogen provided by various scales of nuclear plants

Synthetic fuels (synfuels), also known as electro-fuels (E-fuels), are hydrocarbon fuels produced from waste CO2 streams and water electrolysis, with electricity as the primary source of energy. To achieve substantial reductions in greenhouse gas (GHG) emissions, electricity sources must release zero carbon or near-zero carbon, as is the case with solar, wind, hydro, and nuclear power. Nuclear power is one of the largest and steadiest domestic sources of clean energy in the United States. Moreover, nuclear power has the potential to produce hydrogen economically for less than $2/kg, reaching the DOE near-term target price. Thus, using nuclear power to produce synfuels has the unique potential to significantly reduce the GHG emissions of hydrocarbon fuels production and end-use applications. Fisher-Tropsch or FT fuel (a mixture of naphtha, jet fuel, and diesel) is of great interest because it is a drop-in fuel that can be blended with conventional petroleum counterparts and is compatible with existing infrastructure. By using the ASPEN Plus model, this report develops FT fuel production models on three scales, corresponding to nuclear plants with capacities of 1000 MWe, 437 Mwe, and 100 MWe, respectively. The FT model case with energy from a 437-MWe nuclear plant is used as a baseline case. This report summarizes the baseline ASPEN Plus model results with a detailed mass and energy analysis. Our modeled facility produces 507 MT/day (185,000 gal/day) of FT fuel by converting 255 MT/day of hydrogen and 1,580 MT/day of CO2. The FT fuel production energy efficiency from hydrogen and electricity energy inputs is 70% (lowerheating-value or LHV-based). Including the high-temperature electrolyzer in the system boundary, the FT fuel production LHV efficiency from electricity and thermal energy inputs is 51%, considering 39.8 kWh/kg of electricity and 6.86 kWh/kg of thermal energy use from a nuclear plant for hydrogen production. The FT production efficiency can potentially be increased by further integrating the heat exchange between nuclear plant and FT process, and this study is underway. The carbon conversion ratio in the baseline case is 99%, with process CO2 capture and recirculation and oxy-combustion using the oxygen by-product from water electrolysis. The hydrogen consumption is 1.38 kg/gal-FT fuel and the CO2 consumption is 8.56 kg/gal-FT fuel in the baseline case. With different FT production scales determined by the nuclear plant capacity, the FT model was scaled using the same operating parameters, which led to the same conversion efficiency regardless of scale. However, the different FT plant scales will impact the economics of FT fuel production; this impact will be examined in the next phase of this study.

Zang, Guiyan↗
DOE OSTI2026

Cradle-to-Grave Lifecycle Analysis of U.S. Medium- and Heavy-Duty Vehicle-Fuel Pathways: A Greenhouse Gas Emissions Assessment of Current (2021) and Future (2035) Technologies

This study presents a cradle-to-grave lifecycle analysis of energy use and greenhouse gas (GHG) emissions for U.S. medium- and heavy-duty vehicles across current (2021) and future (2035) technologies using the Greenhouse gas, Regulated Emissions, and Energy use in Technologies (GREET) model with industry-vetted assumptions. Results vary across vehicle classes but point to common trends: today, battery electric vehicles (BEVs) offer significant (10–60%) GHG emissions reduction compared to diesel internal combustion engine vehicles and are the lowest emissions option per ton-mile of cargo movement, followed by hydrogen fuel cell electric vehicles (FCEVs) (5–50% emissions reduction). Emissions savings depend largely on the duty cycle and fuel economy of the vehicle type. Future vehicle technology advancements result in comparable emission reductions associated with BEVs and hydrogen FCEVs. Weight-limited BEV trucks see less per-ton-mile emissions reduction due to the impact of battery weight on increased vehicle weight and reduced payload capacity. By 2035, improvements in vehicle efficiency can reduce emissions across all powertrains. However, very low levels of emissions require switching vehicles’ use-phase fuel/energy to low-carbon fuels and electricity. Renewable diesel, e-fuels, hydrogen produced from natural gas with carbon capture and storage or renewables, and use of low-carbon electricity can all achieve over 70% reduction in GHG emissions from the current day diesel-based internal combustion engine vehicle.

alternative fuels↗
DOE OSTI2020

InSituNet: Deep Image Synthesis for Parameter Space Exploration of Ensemble Simulations

We propose InSituNet, a deep learning based surrogate model to support parameter space exploration for ensemble simulations that are visualized in situ. In situ visualization, generating visualizations at simulation time, is becoming prevalent in handling large-scale simulations because of the I/O and storage constraints. However, in situ visualization approaches limit the flexibility of post-hoc exploration because the raw simulation data are no longer available. Although multiple image-based approaches have been proposed to mitigate this limitation, those approaches lack the ability to explore the simulation parameters. Our approach allows flexible exploration of parameter space for large-scale ensemble simulations by taking advantage of the recent advances in deep learning. Specifically, we design InSituNet as a convolutional regression model to learn the mapping from the simulation and visualization parameters to the visualization results. With the trained model, users can generate new images for different simulation parameters under various visualization settings, which enables in-depth analysis of the underlying ensemble simulations. We demonstrate the effectiveness of InSituNet in combustion, cosmology, and ocean simulations through quantitative and qualitative evaluations.

deep learning↗
DOE OSTI2024

In-cylinder spray evolution in a motored central-injection gasoline engine: Imaging and simulating the effects of flash-boiling and intake crossflow

Accurate predictions of fuel spray behavior and mixture formation in simulations of direct-injection spark-ignition (DISI) engines are fundamental to ensure proper description of all subsequent processes including ignition, combustion, and emissions. In this work, the spray evolution in a single-cylinder optical DISI engine was studied experimentally and numerically with the goal of enabling predictive computational fluid dynamics (CFD) modeling of in-cylinder sprays. The authors explored a wide range of operating conditions characterized by several fuel injection temperatures and engine speeds, using a well-characterized nine-component gasoline surrogate known as PACE-20. The effect of flash boiling and intake crossflow on the spray is discussed, with a focus on evaluating the ability of the spray models to capture highly transient spray behavior. In the experiments, the fuel temperature was varied between 20°C and 80°C, allowing for non-flash- to flash-boiling transition to emerge with enhanced flashing intensity at the highest temperatures. Spray collapse resulted in vapor-rich regions, owing to the locally lower inertia of the fluid. Varying the engine speed from 650 to 1950 rpm promoted increasingly more turbulent in-cylinder crossflow which interacted with the spray during the injection event and resulted in enhanced spray dispersion. The CFD model was able to capture the spray morphology transition at different fuel temperatures and engine speeds adequately. Further, it is shown that the spray breakup model could capture the transitional spray behavior induced by flash boiling atomization and intake flow via proper initialization of the spray cone angle and calibration of the spray models’ constants.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2022

SSR COST – COmposite Structural Technologies for advanced reactor deployment (Final Scientific/Technical Report)

Moltex is designing a Generation 4 or Advanced nuclear reactor, the molten salt fast spectrum SSR-W. The design intent is to reduce the cost and complexity of the nuclear systems by relying on inherent safety characteristics, instead of engineered systems. One such characteristic as a natural tendency for power to decrease as temperature increases. Another characteristic that improves natural safety is the fact that the working fluids (molten salts) are at atmospheric pressure at operating temperatures. This significantly reduces the need for pressure boundary components and systems. Moltex is highly motivated to develop simple and economic reactors to reduce the carbon intensity and improve energy security of global electricity production. The COST project investigated the opportunities for reducing construction cost of advanced reactors with the adoption of Rigid Elastic Composite Civil works (RECC). The construction design and methods used in currently operational light water power plants would generally be suboptimal for the SSR-W since there is no requirement for civil structures to withstand high pressure accidents such as hydrogen combustion or steam explosion. In parallel to downselecting the most promising RECC-type technology, accident scenarios representing the largest credible challenge to the SSR-W civil and construction design were modelled. The capability of an SSR-W reactor constructed with and without the selected construction technology was evaluated and the consequential licensing challenges identified. A construction schedule and cost estimate of the SSR-W with and without the selected RECC construction technology was developed. Once the above data was collected, then Moltex was able to review the safety performance, license-ability and cost/schedule benefit of applying the preferred construction technology. The CAPEX/NPV benefit was quantified, and the licensing risks and opportunities were documented. Finally, the CAPEX/NPV benefit of the advanced construction technology was modest due to the suitability of traditional stick-built construction for the SSR-W design. However, previously unidentified benefits of the advanced construction technology were revealed during the studies that could credibly de-risk certain aspects of the design to be licensed. Since licensing (duration and delays) are very significant in new build project costs, the cost benefits may be significant. Further studies on the risk reduction of the construction technology are foreseen.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Design and Evaluation of Environmental Barrier Coatings for Protection of Ceramic Matrix Composites in Hydrogen-Based Turbines

This presentation at the 2024 FECM Spring Project Review Meeting summarizes ongoing work at NETL aimed at enabling the use of ceramic matrix composite (CMC) materials in next-generation high-efficiency power generation turbines fueled by hydrogen, natural gas, or other fuels. The work broadly involves three aspects (1) phase-field damage modeling of CMCs and the environmental barrier coatings (EBCs) used to protect them (2) computational design of new and improved EBCs and (3) performance testing of EBCs using a novel gas turbine combustion simulation rig developed at NETL. An overview on current status and next steps for each aspect of the project are presented.

ceramic matrix composite (CMC)↗
DOE OSTI2025

Exploring anomalous electron decay in nanosecond repetitively pulsed discharges

Nanosecond pulsed discharges (typical pulse duration of about 10 nanoseconds) have attracted widespread attention due to their wide range of applications in plasma-assisted combustion and aerodynamic flow control, biomedicine, nanotechnology, and materials processing. This project investigated the plasma dynamics of nanosecond discharges in a pin-to-pin configuration using a combined experimental and theoretical modeling approach, leveraging the expertise and resources of Purdue University and the Princeton Collaborative Research Facility (PCRF).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Effects of non-thermal termolecular reactions on wedge-induced oblique detonation waves

The shock-induced combustion ramjet (Shcramjet) based on oblique detonation waves (ODWs) is among the promising choices for hypersonic propulsion systems. An understanding of the ignition, propagation, and stability of ODWs is critical to harnessing their propulsive potential. In such high speed reacting flows, there is a high probability of occurrence of non-thermal reactions due to the presence of non-trivial amounts of highly reactive radicals including H, O and OH apart from O 2 as demonstrated recently [M. P. Burke, S. J. Klippenstein, Nat. Chem. 9 (2017) 1078–1082, Y. Tao, A. W. Jasper, Y. Georgievskii, S. J. Klippenstein, R. Sivaramakrishnan, Proc. Combust. Inst. 38 (2021) 515–522]. The present work focuses on examining the initiation, propagation and structure of oblique detonation waves in stoichiometric H 2 -air mixtures through numerical simulations with and without non-thermal reactivity on a two-dimensional adaptive grid. Non-thermal reactions were included in the macroscopic kinetic model as chemically termolecular reactions facilitated by the H + OH radical-radical recombination and the H + O 2 radical-molecule association reactions. Since, the non-thermal reactions result in a corresponding decrease in the reaction fluxes of the incipient recombination/association reactions, an additional simulation was performed by applying corrections to the respective incipient recombination/association rate constants using the methodology demonstrated by Tao et al. [Y. Tao, A. W. Jasper, Y. Georgievskii, S. J. Klippenstein, R. Sivaramakrishnan, Proc. Combust. Inst. 38 (2021) 515–522]. Results show that, under ODWE relevant conditions, non-thermal reactivity fundamentally alters the induction length, intensity as well as the structure of the ODW. Specifically, it is found that non-thermal reactivity leads to a noticeable reduction in initiation length and a simultaneous increase in instantaneous peak heat release rate and the degree of unsteadiness of the ODW. Finally, statistical analysis of key thermo-chemical variables is performed to elucidate the important species as well as reactions responsible for the observed variations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Collaborative: in situ visual analytics technologies for extreme scale combustion simulations

This project aims to drastically enhance the usability of in situ analysis and visualization for extreme-scale scientific simulations. Current exascale computing capabilities promise to offer greater predictive ability of simulations and to further push the frontiers of science and technology. However, to validate the simulation output at extreme scale, examine the modeled phenomena, and discover previously unknowns from the output data, the output must be reduced or transformed in situ as it is being generated during the simulation such that the amount of data to examine and store is kept to a minimum. Such in situ approaches allow us to process and analyze the data and any embedded geometry to an extent that would be prohibitively expensive, if not impossible, to perform as a post hoc task. While in situ processing has been demonstrated to be a feasible and promising approach, its full potential has not yet been leveraged. In this project, we have developed comprehensive enhancements to in situ technology based on probability distributions in data. Our research focuses on jointly developing new ways of interacting with massive statistical samples while creatively utilizing new state-of-the-art computational resources to push the boundaries of in situ exploration. Moreover, we have developed new time-dependent techniques to enable previously unattainable capabilities in areas such as intelligent simulation steering and precise feature identification. We have experimentally studied our design and implementation at NERSC and OLCF, and are able to leverage existing in situ infrastructures whenever possible. While the exemplar in this project is combustion, many other fields for which turbulent transport is important, e.g., fusion, climate, astrophysics among others, encounter similar issues as simulations scale up to the exascale. This project shows its potential to generate high impact on DOE missions since the resulting technology promises to improve scientists’ ability to rapidly and correctly interpret and tune extreme-scale simulations, leading to new scientific understanding and advancements.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2024

Data assimilation for combustion ignition delay time simulation using schlieren image velocimetry

This study sought to improve the accuracy of simulating spray penetration and combustion ignition delay by means of data assimilation (DA). The simulations were conducted using the Reynolds-averaged Navier–Stokes (RANS) equations and assimilating the schlieren image data. In DA, an ensemble square root filter (EnSRF) was used to build the statistical model, making the simulation results more accurate without any change in the governing equations. Recognizing that the spray-cone injection angle has a large effect on penetration, we created ensemble members with different injection angles. And we applied the two-component velocity distribution calculated via SIV and updated both velocity and temperature by using a DA statistical model derived from RANS ensemble simulations. The ignition delay time is generally known to vary even under the same experimental conditions because it is influenced by many factors. In this study, we attempted the transient DA-assisted RANS simulation to predict the ignition delay time even when the temporal resolution and accuracy of the observation data ware insufficient. Our trials offer an example of how a combination of techniques can be effectively used to assimilate experimental data obtained under restricted conditions.

Combustion simulation↗
DOE OSTI2025

AUTOIGNITION DELAY TIMES FOR REFORMATE GAS MIXTURES FROM METHANE GAS ENGINES

Methane slip is a prominent issue in natural gas reciprocating engines that are used in transportation and marine applications. The incomplete combustion that results in methane slip can be resolved with the introduction of hydrogen within the combustion mixture to improve methane oxidation and further enable combustion within the engine crevices where methane has previously remained unreacted. Steam methane reforming (SMR) is a common method used to produce hydrogen and can be used to design an onboard device to reduce methane slip from reciprocating engines. The development of this reformer device requires the validation of high-fidelity chemical kinetic models at the low temperatures of the crevice volumes of these engines. In this work, auto-ignition data is obtained using a shock tube at lean (φ—0.714 or λ—1.4) and stoichiometric (φ, λ = 1) equivalence ratios spanning a temperature range of 1042–1234 K at the 80-bar operating pressure of the test engine. Blends of methane, hydrogen, and reformate products from the SMR reaction are shock-heated in synthetic air, with the ignition delay time measured using an OH* chemiluminescence detector at 310 nm and a CH* detector at 430 nm. The experimental results are compared to several state-of-the-art chemical kinetic mechanisms from the literature. In general, most of the mechanisms show very good agreement with experiments at higher temperatures, with simulation results showing little deviation from experiments at lower temperatures. A sensitivity analysis was conducted, and the results reveal that the reaction H2 + CH3O2 = H + CH3O2H has a very significant role in determining low-temperature ignition delay times (IDTs) of SMR mixtures. These findings provide valuable insights into the chemical kinetics governing methane reformate combustion and contribute to the optimization of onboard reformer designs aimed at mitigating methane slip in natural gas-fueled engines.

Fraze, Matthew↗
DOE OSTI2022

Adsorption and exchange reactions of iodine molecules at the alumina surface: modelling alumina-iodine reaction mechanisms

Harnessing aluminum oxidation energy requires navigating the particle's passivation shell composed of alumina. The shell is a barrier to aluminum oxidation but can also exothermically react with halogenated species and therefore contribute to the overall energy generated during aluminum particle combustion. Fluorination reactions with alumina have been studied because fluorine is abundant in binder formulations that commonly surround aluminum particles in an energetic mixture. However, iodine has emerged as an alternative halogenated-based binder or oxidizer because iodine gas provides ancillary benefits such as chemical neutralization of biological agents or sterilization of contaminated environments. Furthermore, this study used density functional theory (DFT) calculations to evaluate potential reaction pathways for aluminum–iodine combustion. Relative to fluorinated fragments such as HF and F – , the adsorption energies associated with HI and I– are nearly triple the exchange reaction energy available from fluorination reactions with alumina (–189 and –278 kJ mol –1 for HI and I – , respectively). However, exchange reactions between iodinated species and the alumina surface are energetically unfavorable. These results explain that through adsorption, alumina surface exothermic reactions with iodine are more energetic than with fluorine fragments. Experiments performed with differential scanning calorimetry (DSC) confirm the higher magnitude of energy generated for iodination compared with fluorination reactions with alumina. Additionally, strong adsorption energies can promote synthesis of new shell chemistries. Adsorption in solution will promote alumina dissolution and iodine precipitation reactions to produce hydroxyl complexes and iodinated species synthesized on the surface of the particle, thereby replacing alumina with alternative passivation shell chemistry.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Spatially-resolved soot evolution and statistics in high-pressure diesel spray flames using two-color pyrometry

Previous studies of diesel spray flames have focused on details of the sooting behavior mainly during the quasi-steady period, but few have considered the spatially-resolved transient evolution in combination with injection-to-injection variations. In this study, a 500-injection data set is utilized to investigate the temporal evolution of a spray flame during auto-ignition, the premixed burn phase, and the quasi-steady period. Spatially-resolved OH* chemiluminescence data provide ignition delay times and reaction zone locations. Two-color pyrom-etry with a vastly improved optical system is used to quantify spatially-resolved soot evolution and its statistical variations. The ambient thermodynamic con-ditions are slightly below those in modern diesel engines, resulting in longer lift-off lengths and lower overall soot production. Spatially, soot formation in the lift-off region is small, but appreciable soot forms in the jet core and jet head regions, while it oxidizes gradually on the jet periphery. Total soot mass profiles indicate that regions with larger local soot mass take longer to form, but are the first to oxidize. Probability distributions of soot mass in localized regions indicate that a few injections with high soot mass bias the average soot mass data towards higher values. Altogether, results show good agreement with previous studies employing different diagnostic techniques while providing statistical details of transient and localized soot behavior in high pressure diesel spray flames in support of the related modeling efforts.

09 BIOMASS FUELS↗
DOE OSTI2023

Effect of Split-Injection Strategies on Engine Performance and Emissions under Cold-Start Operation

The recently concluded partnership for advancing combustion engines (PACE) was a US Department of Energy consortium involving multiple national laboratories focused on addressing key efficiency and emission barriers in light-duty engines. Generation of detailed experimental data and modeling capabilities to understand and predict cold-start behavior was a major pillar in this program. Cold-start, as defined by the time between first engine crank and three-way catalyst light-off, is responsible for a large percentage of NOx, unburned hydrocarbon, and particulate matter emissions in light-duty engines. Minimizing emissions during cold-start is a trade-off between achieving faster three-way catalyst light-off, and engine out emissions during that period. In this study, engine performance, emissions, and catalyst warmup potential were monitored while the engine was operated using a single direct injection (baseline case) as well as a two-way-equal-split direct injection strategy. These injection strategies were analyzed at a range of cold-start-operation relevant retarded spark timings of up to 25 degrees after top dead center of firing (dATDCf). A stoichiometric 2-bar NIMEP steady-state condition was used for all cases to simulate cold-start operation. Significant improvement in engine stability was observed with the two-way-split injection strategy at the retarded spark timings allowing for up to 2.5x increase in exhaust heat rate when engine operation is stability constrained. Similar fuel-loss-to-oil trends with exhaust heat rate were observed for both single and two-way-split injection strategies. However, the two-way split injection was observed to produce higher NOx emissions per unit exhaust heat rate. A single data point run with three-way-split direct injection at a very retarded spark-timing of 30 dATDCf pointed to further improvements in engine stability and reduction in fuel-loss-to-oil as compared to single injection strategy. Engine stability decreased as spark timing was initially retarded with a single injection but was observed to plateau and stabilize beyond spark timing of 10 dATDCf. Finally, for the two-way-split-injection strategy, retarding the start of injection (SOI) timing of the second injection led to a decrease in engine stability as well as an increase in soot emissions.

42 ENGINEERING↗
DOE OSTI2022

Market-Integrated Optimization of Wind-Battery-Hydrogen Hybrids for Peaking Capacity via Storage

As Integrated Energy Systems (IES) combine multiple energy and storage technologies to provide potentially more value and less risk via resource diversification, complementary overbuild, increased flexibility, and revenue-stacking, IES value is dependent on electricity market dispatch and grid interactions should play an important role in IES design and operation. This study hybridizes and retrofits wind and combustion turbine plants to study the impacts of replacing gas generation capacity with wind, battery, PEM electrolysis, hydrogen tanks and hydrogen turbines. The optimized design is co-simulated in a production cost model with different bidding strategies in order to compare performance and highlight the importance of grid-interactions. We analyze the revenue and dispatch changes as well as the price and cost implications of wind-battery-hydrogen IESs.

electrolysis↗
DOE OSTI2022

Transforming Energy Through Computational Excellence: Bringing Low Mach Number Reactive Flow Simulations at the Exascale

PeleLMeX's unique capabilities are allowing for reactive flow modeling at unprecedented scales and a reasonable time and cost. The code is currently being extended to tackle more practical, design-oriented simulations by implementing Large Eddy Simulation and data-driven chemical models, providing a fast but accurate tool for engineers considering the emergence of GPU-accelerated platforms. These extensions are critical for enabling the physical insight required to design the next generation of combustion devices as a key component of a renewable energy future.

MATHEMATICS AND COMPUTING↗