Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CLADDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

Sagging Mechanisms of Three-Layer Aluminum Clad Foils used in the Heat Exchanger in the Brazing Process

The sagging mechanisms of a three-layer aluminum clad foils (AA4343/AA3003Mod/AA4343) with final rolling reduction of 20-50% during brazing were studied. The results show that the sagging behavior of the aluminum brazed foils during the brazing cycle can be divided into four stages: Stage I is the slight sagging stage, during which sagging deformation can almost be ignored; Stage II is referred to as the accelerative sagging stage, and the sagging behavior is mainly ascribed to recovery. In stage II, the greater the reduction ratio is, the earlier the recovery ends, and the smaller the value of the sagging distance is. Stage III is the slow sagging stage, and sliding deformation along the grain boundaries is responsible for the slow sagging rate. Stage IV is the erosion stage. During stage IV, the coarsely recrystallized grains can inhibit erosion and are helpful in obtaining excellent sagging resistance, while the foils with finely recrystallized grains or non-recrystallized structure show severe erosion and limited sagging resistance.

36 MATERIALS SCIENCE↗

Effect of neutron and ion irradiation on the metal matrix and oxide corrosion layer on Zr-1.0Nb cladding alloys

A detailed study has been carried out on recrystallised Zr-1.0Nb alloys corroded and irradiated under different conditions, including ex-autoclave and ex-reactor samples. After 540 days in reactor and damage around 5 dpa, the neutron irradiated sample shows no serious evidence for radiation enhanced corrosion and is still in pre-transition stage. The good corrosion resistance of the neutron irradiated Zr-1.0Nb can be related to the higher volume fraction of tetragonal phase and fewer interconnected nano porosity/cracks in the oxide. This indicates less tetragonal to monoclinic transition, leads to more protective oxide in the neutron irradiated sample, containing little evidence for short circuit paths for the penetration of oxygen or water towards the metal-oxide interface. These observations on a sample with a slow overall oxidation rate are consistent with the hypothesis that interconnected porosity can lead to early transitions and rapid oxidation. Tetragonal oxide can be either stabilised by irradiation, or stabilised by local release of impurity species from SPPs such as dissolution of Fe from Zr-Nb-Fe precipitates or radiation introduced precipitates (RIPs) which is likely to be small β-Nb clusters. The oxide consists of well-aligned columnar-equiaxed microstructure in the autoclave sample while a more complex oxide grain structure was observed in the neutron-irradiated sample. As oxide continues to grow, there are more < a > and < c > loops, dissolved Fe and RIPs in the metal matrix, however, the corrosion rate is low enough for the tetragonal oxide to stabilise and suboxide + Zr(Osat) phases exist for protectiveness, so there is no enhanced corrosion after radiation. In situ ion irradiation in the TEM revealed no visible defect clusters or voids in the oxide, suggesting that radiation damage to the metal matrix rather than oxide may have a stronger effect on corrosion mechanisms after neutron irradiation, however, cascade damages are not visible in this case. Neutron irradiation also seems to have little effect on promoting fast oxidation or dissolution of β-Nb precipitates into the surrounding oxide or metal during irradiation. Furthermore, these results are discussed in the light of the current mechanisms for corrosion of nuclear fuel cladding alloys.

(S)TEM↗

Effect of PVD-coated chromium on the subcooled flow boiling performance of nuclear reactor cladding materials

Here we elucidate the separate effect of a thin Cr coating deposited by physical vapor deposition (PVD) on the subcooled flow boiling performance of zircaloy-4. First, we run flow boiling experiments on prototypical zircaloy-4 surfaces mimicking the scratch pattern and surface roughness of nuclear reactor claddings. Then, we PVD-coat a 0.3 µm thick chromium layer on the same exact surface and repeat the same flow boiling investigations. All experiments are run using deionized water at atmospheric pressure, flowing on a 1 × 3 cm 2 rectangular cross section channel at a rate of 1000 kg/m 2 /s and a subcooling of 10 K. We measure the average temperature of the boiling surface at increasing surface heat fluxes, covering a wide range of heat transfer regimes, from single-phase forced convection to the boiling crisis. We also record high-speed videos of the boiling process, which we postprocess to measure bubble nucleation site density, growth time, departure diameter and frequency. The surface analysis reveals that, while the chromium coating does not seem change the surface roughness and morphology, it improves surface wettability. However, it decreases the critical heat flux. The chromium coating causes an increase of nucleation temperature, bubble departure diameter and growth time, and a reduction of the nucleation site density. The concurrence of these observations indicates that a size reduction of the nucleation sites, conformally covered by the chromium coating, may be the cause of the boiling performance deterioration. We confirm this hypothesis repeating the same analysis on a FeCrAl sample prepared and tested using the same protocol as the zircaloy-4 sample, but with a different initial surface texture.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

Charge Optimized Many Body (COMB) potentials for simulation of nuclear fuel and clad

The Charge Optimized Many Body (COMB) potential formalism enables the molecular dynamics simulation of complex materials structures in which multiple types of bonding (metallic, covalent, ionic and secondary bonding) coexist. Here we briefly review the COMB formalism and illustrate its capabilities to address critical issues in the area of nuclear fuel. In particular, we In Section 3, we look at U, UO2 and the process of oxidation of U. In Section 4, we look at the mechaincal behavior of Zr, representing LWR clad, and explore the effects of oxidation and hydridation on the mechanical response. In Section 5, we describe the capabilities of COMB simulations of corrosion. Since there has been relatveily little work done in this area, we also describe some work performed on non-nuclear materials, which illustrate the capabilities. Section 6 briefly describes some of the known limitations of the COMB approach.

36 MATERIALS SCIENCE↗

Comparison of steady and transient flow boiling critical heat flux for FeCrAl accident tolerant fuel cladding alloy, Zircaloy, and Inconel

Steady and transient (with a heating rate of 685?/s) internal-flow CHF (Critical Heat Flux) experiments were conducted under atmospheric pressure at a fixed inlet temperature (40? or 60?) and mass flow (300kg/m 2 s) on Fe-13Cr-6Al alloy, Inconel 600 and Zircaloy-4 tube samples. Multiple experiments were repeated on the same specimen to investigate the effect of surface characteristic changes (i.e., roughness, wettability, and oxide scale morphology) on the occurrence of CHF. Despite notable changes of wettability, roughness, and oxide layer characteristics on samples that had already been subjected to CHF, measured flow CHF remained unchanged throughout repeated experiments for tested materials. This demonstrates that the surface effects on flow CHF are limited in the test conditions. In the steady-state flow boiling condition, Fe-13Cr-6Al alloy demonstrated a 22% and 14% increase in CHF compared to Zircaloy-4 and Inconel 600, respectively. Compared to the 2006 Groeneveld CHF lookup table, Fe-13Cr-6Al alloy gives a 13% increase in the tested flow boiling condition. Material properties are considered primarily responsible for the observed CHF differences among the tested materials. The surface thermal economy parameter $\frac{(pc_p)^{3/2}}{\sqrt{k}}$ is proposed as an explanation for the observed CHF differences; this parameter is related to material’s ability to avoid an irreversible dry spot formation. The apparent disagreement of Zircaloy-4 CHF with both the look up table predictions and Inconel 600 shows the limitation of departure of nuclate boiling (DNB) evaluations that do not consider cladding materials. The transient Fe-13Cr-6Al CHF is 39% and 23% higher than the lookup table prediction and the steady-state condition experimental result, respectively.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

High temperature oxidation behavior of Zr-1Nb cladding alloy E110.

Oxidation experiments were conducted at 1000-1200 C in flowing steam with samples of as-received Zr-1Nb alloy E110 tubing and/or polished E110 tubing. The purpose was to determine the oxidation behavior of this alloy under postulated loss-of-coolant accident conditions in light water reactors. The as-received E110 tubing exhibited a high degree of susceptibility to nodular oxidation and breakaway oxidation at relatively low test times, as compared to other cladding alloys. The nodules grew much more rapidly at 1000 C than 1100 C, as did the associated hydrogen uptake. The oxidation behavior was strongly affected by the surface condition of the materials. Polishing to {approx}0.1 {micro}m roughness (the roughness of the as-received tubing was {approx}0.4 {micro}m) delayed breakaway oxidation. Polishing also removed surface impurities. For polished samples oxidized at 1100 C, no significant nodular oxidation appeared up to 1000 s. For polished samples oxidized at 1000 C, hydrogen uptake >100 wppm was delayed from {approx}300 s to >900 s. Weight-gain coefficients were determined for pre-breakaway oxidation of polished-only and machined-and-polished E110 tubing samples: 0.162 (mg/cm{sup 2})/s{sup 0.5} at 1000 C and 0.613 (mg/cm{sup 2})/s{sup 0.5} at 1100 C.

08 HYDROGEN↗

Development and property evaluation of nuclear grade wrought FeCrAl fuel cladding for light water reactors

Development of nuclear grade, iron-based wrought FeCrAl alloys has been initiated for light water reactor (LWR) fuel cladding to serve as a substitute for zirconium-based alloys with enhanced accident tolerance. Ferritic alloys with sufficient chromium and aluminum additions can exhibit significantly improved oxidation kinetics in high-temperature steam environments when compared to zirconium-based alloys. In the first phase, a set of model FeCrAl alloys containing 10–20Cr, 3–5Al, and 0–0.12Y in weight percent, were prepared by conventional arc-melting and hot-working processes to explore the effect of composition on the properties of FeCrAlY alloys. It was found that the tensile properties were insensitive to the alloy compositions studied; however, the steam oxidation resistance strongly depended on both the chromium and the aluminum contents. The second phase development focused on strengthening Fe-13Cr-5Al with minor alloying additions of molybdenum, niobium, and silicon. Combined with an optimized thermo-mechanical treatment, a thermally stable microstructure was produced with improved tensile properties at temperatures up to 741°C.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Development of low-Cr ODS FeCrAl alloys for accident-tolerant fuel cladding

Low-Cr oxide dispersion strengthened (ODS) FeCrAl alloys were developed as accident tolerant fuel cladding because of their excellent oxidation resistance at very high temperature, high strength and improved radiation tolerance. Fe-12Cr-5Al wt.% gas atomized powder was ball milled with Y 2 O 3 +FeO, Y 2 O 3 +ZrO 2 or Y 2 O 3 +TiO 2 , and the resulting powders were extruded at 950°C. The resulting fine grain structure, particularly for the Ti and Zr containing alloys, led to very high strength but limited ductility. Comparison with variants of commercial PM2000 (Fe-20Cr-5Al) highlighted the significant impact of the powder consolidation step on the alloy grain size and, therefore, on the alloy mechanical properties at T < 500 °C. These low-Cr compositions exhibited good oxidation resistance at 1400 °C in air and steam for 4 h but could not form a protective alumina scale at 1450 °C, similar to observations for fine grained PM2000 alloys. As a result, the effect of alloy grain size, Zr and Ti additions, and impurities on the alloy mechanical and oxidation behaviors are discussed.

36 MATERIALS SCIENCE↗

High-temperature oxidation and quenching of chromium-coated zirconium alloy ATF cladding tubes with and w/o pre-damage

Chromium-coated zirconium alloys are one of the promising candidates for accident-tolerant fuel cladding (ATF) tubes for light water reactors (LWRs). In this study, the high temperature oxidation and degradation of two types of Cr coatings (cold spray and physical vapor deposition) with and without pre-damage by scratches were investigated on prototype rod segment samples filled with ZrO 2 pellets and tightly sealed with welded end caps. Isothermal tests at 1100 and 1200 °C were terminated by quenching with water; transient tests were performed up to 1500–1600 °C until complete coating failure. The positive effect of both types of Cr coatings was observed in all tests. Pre-damaged specimens showed only locally increased oxidation of the scratched zone, but no negative effects on the adjacent Cr coating. Finally, the behavior of the two types of coatings is compared and the degradation mechanisms are discussed based on hydrogen release data, extensive metallographic post-test examinations, and the current state of global research.

36 MATERIALS SCIENCE↗

Burst characteristics of advanced accident-tolerant FeCrAl cladding under temperature transient testing

Here assessment of burst characteristics of accident-tolerant fuel (ATF) claddings is essential to evaluate the safety margins of nuclear reactors, and better understanding can enable accelerated licensing for reactor concepts that include the new materials. Therefore, this study investigated the burst behavior of an ATF candidate of C26M, which is an iron–chromium–aluminum alloy (FeCrAl) under transient testing like the simulated loss-of-coolant accident (LOCA) conditions, except the water-quenching phase, in light-water reactors (LWRs). The effect of LOCA specimen length was assessed in terms of post-burst tube parameters. No critical length effect was determined on the burst pressure, burst location, and burst size measurements. Burst temperature showed larger variation likely due to its measurement approach used in this study. The post-test diametral strain was identified as the critical parameter to reduce the specimen length as compared to tube burst length or width. Postmortem optical metrology and digital image correlation were employed to determine the local strain-state during the simulated LOCA, which showed the loading path was close to equibiaxial conditions in regions away from the burst location, rather than internally pressurized conditions (or “plane-strain” tension). Pst-test microstructural characterizations of the FeCrAl revealed that ductile damage was present at the edge of the outer radial surface while the rest of the material was ruptured via cleavage at LOCA burst temperatures. Furthermore, internal grain boundary cracks were observed at locations away from the tube burst region. This behavior was considered to occur during the cooling down period of the simulated LOCA test. Overall, this study aimed to provide essential data for fuel performance code development by considering micromechanics of the deformation and failure.

36 MATERIALS SCIENCE↗

Effects of high temperature treatment on microstructure and mechanical properties of laser-clad NiCrBSi/WC coatings on titanium alloy substrate

Laser-clad composite coatings on the Ti6Al4V substrate were heat-treated at 700, 800, and 900 °C for 1 h. The effects of post-heat treatment on the microstructure, microhardness, and fracture toughness of the coatings were investigated by scanning electron microscopy, X-ray diffractometry, energy dispersive spectroscopy, and optical microscopy. The wear resistance of the coatings was evaluated under dry reciprocating sliding friction at room temperature. The coatings mainly comprised some coarse gray blocky (W,Ti)C particles accompanied by the fine white WC particles, a large number of black TiC cellular/dendrites, and the matrix composed of NiTi and Ni{sub 3}Ti; some unknown rich Ni- and Ti-rich particles with sizes ranging from 10 nm to 50 nm were precipitated and uniformly distributed in the Ni{sub 3}Ti phase to form a thin granular layer after heat treatment at 700 °C. The granular layer spread from the edge toward the center of the Ni{sub 3}Ti phase with increasing temperature. A large number of fine equiaxed Cr{sub 23}C{sub 6} particles with 0.2–0.5 μm sizes were observed around the edges of the NiTi supersaturated solid solution when the temperature was further increased to 900 °C. The microhardness and fracture toughness of the coatings were improved with increased temperature due to the dispersion-strengthening effect of the precipitates. Dominant wear mechanisms for all the coatings included abrasive and delamination wear. The post-heat treatment not only reduced wear volume and friction coefficient, but also decreased cracking susceptibility during sliding friction. Comparatively speaking, the heat-treated coating at 900 °C presented the most excellent wear resistance. - Highlights: • TiC + WC reinforced intermetallic compound matrix composite coatings were produced. • The formation mechanism of the reinforcements was analyzed. • Two precipitates were generated at elevated temperature. • Cracking susceptibility and microhardness of the coatings were improved. • Post-heat treatment enhances wear resistance of the coatings.

36 MATERIALS SCIENCE↗

Precipitation behavior of stainless steel weld overlay cladding exposed to a long-term thermal aging

Highlights: • Silicide phase formation with G-phase was first time to be observed. • Precipitation behavior discrepancy existed at different locations of ferrite phase. • G-phase and silicide phase formed along dislocations and within ferrite matrix. • Heterogeneous distribution of elements induced silicide phase formation. - Abstract: Thermal aging behavior of stainless steel weld overlay cladding aged at 400 °C for 10,000 h was investigated. The results showed that the precipitates along the dislocation and within ferrite matrix contained the face-centered cubic structural G-phase and silicide phase. Silicide phase, supposed to be (Fe, Mn){sub 3}Si phase, preferred to form with G-phase along the dislocations and within ferrite matrix. Silicide phase showed a cube-on-cube relationship with ferrite phase and G-phase. Heterogeneous distribution of elements within Ni-Mn-Si clusters was responsible for silicide phase formation during thermal aging process, and the corresponding precipitation behavior discrepancy at different forming sites (dislocations, ferrite matrix and phase boundary) was discussed.

36 MATERIALS SCIENCE↗

Biaxial creep performance of CWSR Zircaloy-4 cladding at emulated off-normal conditions of interim dry storage facility

In this study, biaxial creep behavior of hydrided Zircaloy-4 cladding was tested at 500 degrees C. Creep-life was inversely proportional to H-concentration up to 750 wppm. The weakening through hydride reorientation of hydrided specimens was not observed by optical microscopy. The power-law stress exponents and the TEM observation supported the high-temperature climb mechanism dominated the creep behavior in secondary stage.

36 MATERIALS SCIENCE↗

Assessment of coated cladding impact on large-break LOCA with TRACE-DAKOTA

Since 2011, the U.S. Department of Energy has launched new research and development (R&D) programs for developing new accident tolerant fuels (ATFs). These new fuel concepts are expected to bring several advancements in terms of plant safety. However, development, licensing, as well as deployment of ATF require a substantial investment among fuel vendors, operating utilities, and regulatory authorities. For ATF to be economically feasible, credited safety benefits may be necessary to provide an economic incentive for transition of nuclear power plants from Zr/UO2-based fuel technologies to ATFs. As a result, it is essential to evaluate the economic viability of ATF by conducting a comprehensive safety benefits study informed by R&D and demonstration studies. In the present work, based on the best estimate plus uncertainty methodology, sensitivity analysis and uncertainty quantification for key safety quantities under LB-LOCA are performed for the Peach Bottom boiling water reactor (BWR) with GE14 nuclear fuel design adopting the ATF concepts. A coupled TRACE-DAKOTA analysis framework is adopted to perform the uncertainty quantification. Based on the computational results and obtained statistics, the coping time increase, fuel performance improvement as well as the most dominating phenomena during the accident for Cr-coated cladding are investigated in detail. Overall, the results obtained are useful for subsequent plant PRA study and support a move to more modernized performance-based regulatory requirements to realize plant economic benefits.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

High Resolution Neutron Radiography and Tomography of Hydrided Zircaloy-4 Cladding Materials

Neutron radiography for hydrogen analysis was performed with several Zircaloy-4 cladding samples with controlled hydrogen concentrations up to 1100 ppm. Hydrogen charging was performed in a process tube that was heated to facilitate hydrogen absorption by the metal. A correlation between the hydrogen concentration in the hydrided tubes and the neutron intensity was established, by which hydrogen content can be determined precisely in a small area (55 m x 55 m). Radiography analysis was also performed to evaluate the heating rate and its correlation with the hydrogen distribution through hydrided materials. In addition to radiography analysis, tomography experiments were performed on Zircaloy-4 tube samples to study the local hydrogen distribution. Through tomography analysis a 3D reconstruction of the tube was evaluated in which an uneven hydrogen distribution in the circumferential direction can be observed.

hydride↗

Radiolytic evaluation of select sulfur chlorides (S 2 Cl 2 and SOCl 2 ) for advanced low temperature chlorination of zirconium-based used nuclear fuel cladding

New sulfur chloride compounds—sulfur monochloride (S 2 Cl 2 ) and thionyl chloride (SOCl 2 )—have been proposed as alternative chlorinating agents for the chemical decladding of zirconium-based used nuclear fuel cladding materials. However, the radiation stability of these compounds has not been thoroughly evaluated, despite envisioned process conditions involving intense, multi-component radiation fields. Knowledge of the radiation chemistry of these sulfur chlorides is essential for the development and optimization of alternative chlorination technologies. To this end, we present preliminary findings on the gamma radiolysis of neat S 2 Cl 2 and SOCl 2 at ambient temperature up to ~ 34 MGy. In this study, Raman spectroscopy and density functional theory calculations were used to identify the Raman-active degradation products from S 2 Cl 2 and SOCl 2 radiolysis. Both sulfur chloride compounds exhibited significant radiation resistance, with respect to changes in the Raman signatures of the parent compounds and the ingrowth of Raman-active degradation products. For S 2 Cl 2 , molecular chlorine (Cl 2 ) was directly identified as the predominant degradation product, which was completely consumed at higher absorbed doses (> 9 MGy). Similarly, the main degradation product from SOCl 2 radiolysis was also Cl 2 , although in this system it continued to grow in with dose over the entire dose range. Further, an “S=O” containing degradation product(s) was also identified as a compliment to Cl 2 . Overall, the perceived radiation resistance of these sulfur chloride compounds makes them suitable for inclusion in a used nuclear fuel chemical decladding process, especially as radiolytically formed Cl 2 can be used to reform the parent compounds, thereby increasing the longevity of the solvents used.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗

AC Magnetometry Using Nano-ferrofluid Cladded Multimode Interferometric Fiber Optic Sensors for Power Grid Monitoring Applications

The AC magnetic field response of the superparamagnetic nano-ferrofluid is an interplay between the Neel and Brownian relaxation processes and is generally quantified via the susceptibility measurements at high frequencies. The high frequency limit is dictated by these relaxation times which need to be shorter than the time scale of the time varying magnetic field for the nano-ferrofluid to be considered in an equilibrium state at each time instant. Even though the high frequency response of ferrofluid has been extensively investigated for frequencies up to GHz range by non-optical methods, harnessing dynamic response by optical means for AC magnetic field sensing in fiber-optic-based sensors-field remains unexplored. Instead, the incorporation of nano-ferrofluid as sensing materials has been only limited to DC magnetic field sensing, often citing their long response time as a limiting factor to AC field sensing. This work reports the finding of high frequency (up to 15 kHz) AC magnetic field sensing capability of nanomagnetic fluid as the cladding material of a fiber-optic multimode interferometry (MMI) structure optimized for the fourth self-imaging spectral response. The key parameter enabling high frequency response is the short response time (<1 ms) achieved by optimizing both the sensing structure and nano-ferrofluid solution. Focus has been imparted on 60 Hz line-frequency profiles of various current/magnetic fields to test the efficacy of these sensors in metering and monitoring current and current-induced magnetic fields in the electrical power grid systems. The magnetic field sensitivity of 240 mV/Gauss per dBm of transmitted power was achieved for 60 Hz field applied via Helmholtz coil, whereas the 60 Hz AC current sensitivity of 2.83 mV/A was measured due to magnetic field induced by current in a straight conducting wire.

42 ENGINEERING↗

Enhanced Raman scattering assisted by ultrahigh order modes of the double metal cladding waveguide

Distinguished from the usual strategy to enhance the Raman scattering such as creating hot spots in the surface-enhanced Raman scattering, this paper takes a quite different approach based on the double metal cladding waveguide. The target analyte is located in the guiding layer of sub-millimeter scale, where several ultrahigh order modes with high intensity are simultaneously excited via a focused laser beam. The experimental setup is simple, and both simulation and experimental results confirm the enhancement mechanism of these oscillating modes. Other appealing features include the large detection area and the ability to excite guided modes via both polarizations. This scheme can be applied to large molecules detection and readily integrated with other Raman enhancement techniques.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗