SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Flight and calibration results are presented for the Ares I-X 5-hole probe. The probe is calibrated by using a combination of wind tunnel, CFD, and other numerical modeling techniques. This is then applied to the probe flight data and comparisons are made between the vanes and 5-hole probe. Using this and other data it is shown the probe was corrupted by water rendering that measurement unreliable.
The intrusion of planetary dust inside space vehicles on future Lunar missions may lead to performance compromises of the cabin air-filtration system. The evasive character of the fine planetary dust, in particular lunar dust, could enable the dust to make its way through the seals and barriers of the EVA hatches and become airborne in the cabin. This can result in performance and capacity overload of the high efficiency filter media and particle separation systems. Adequate pre-filtration can substantially reduce the load on the higher efficiency components leading to smaller dust loads during surge and nominal dust loading conditions, thereby protecting and extending the life of these components. A particle separation concept, based on centrifugal separation, is being investigated for its application as a pre-filter. The concept has previously been proposed for application in the aircraft engine industry, as means of capturing corrosive dust and salt deposits that may harm the engine. The technique has the advantages of being passive, integrable to HVAC and space vehicle architecture, and has the potential for high degree of particle separation with proper fluid dynamic design. Computational Fluid Dynamics (CFD) and particle tracing modeling were used to arrive at an initial design for rapid prototyping and testing. If feasible, the concept can be integrated to the Scroll Filter System which is being developed by NASA to address the filtration demands on long during spaceflight and surface missions. This paper will describe the modeling results of this concept.
The intrusion of planetary dust inside space vehicles on future Lunar missions may lead to performance compromises of the cabin air-filtration system. The evasive character of the fine planetary dust, in particular lunar dust, could enable the dust to make its way through the seals and barriers of the EVA hatches and become airborne in the cabin. This can result in performance and capacity overload of the high efficiency filter media and particle separation systems. Adequate pre-filtration can substantially reduce the load on the higher efficiency components leading to smaller dust loads during surge and nominal dust loading conditions, thereby protecting and extending the life of these components. A particle separation concept, based on centrifugal separation, is being investigated for its application as a pre-filter. The concept has previously been proposed for application in the aircraft engine industry, as means of capturing corrosive dust and salt deposits that may harm the engine. The technique has the advantages of being passive, integrable to HVAC and space vehicle architecture, and has the potential for high degree of particle separation with proper fluid dynamic design. Computational Fluid Dynamics (CFD) and particle tracing modeling were used to arrive at an initial design for rapid prototyping and testing. If feasible, the concept can be integrated to the Scroll Filter System which is being developed by NASA to address the filtration demands on long during spaceflight and surface missions. This paper will describe the modeling results of this concept.
Explore the source record for details and available documents.
Explore the source record for details and available documents.
A series of Reynolds-averaged Navier-Stokes (RANS) simulations were performed using the FUN3D flow solver to explore the capabilities of the Langtry-Menter Shear-Stress Transport (LM-SST) transition model for predicting transition for aircraft inlet applications. Two geometries were simulated: a zero-pressure-gradient flat plate and an axisymmetric cone exposed to hypersonic flow. In addition to the transition-sensitized LM-SST model investigations, simulations were run with the one-equation Spalart-Allmaras (SA) and the two-equation Menter Shear-Stress Transport (SST-V) RANS models in fully turbulent mode to identify the natural RANS model transition behavior as a function of Mach number when executed in fully turbulent mode. The flat plate simulations showed that (1) the transition model was able to predict rapid transition at a freestream Mach number of 0.2, which is expected but (2) the predicted transition location moved downstream as the freestream Mach number was increased for the simulations that used the SST-V turbulence model. The latter is significant as it is usually assumed that one- and two-equation turbulence models will produce fully turbulent flow very near the boundary layer origin. The flat plate simulation freestream Mach number trend was confirmed with simulations using the Wind-US code, which also saw a similar trend when employing the SA turbulence model. For the axisymmetric cone simulations, the transition location was highly sensitive to the inflow turbulence levels. This is significant as the prediction of the transition location is crucial when trying to predict inlet performance, especially for hypersonic vehicle applications. It was also noted that the predicted transition location for the cone when using the SST-V turbulence model agreed well with the predicted transition location from the equivalent zero-pressure-gradient flat plate case.
As computing technology continues to improve, simulating unsteady aerodynamic environments on launch vehicle geometries becomes more viable. For NASA’s Space Launch System, the flowfield is characterized by large regions of unsteady turbulent wall-bounded flow. Simulating these unsteady wall-bounded environments is of interest to the SLS Aerodynamics team. Wall-modeled LES methods are currently the best approach for simulating these environments in engineering applications. Less-expensive computationally than fully-resolved methods while maintaining many of the benefits in simulating unsteady environments. Before applying these methods blindly to large geometries, best practices can first be applied and understood on smaller canonical problems.
The Baldwin-Lomax model is used in many CFD codes because it is quick and easy to implement. In this paper, we discuss implementing the Baldwin-Lomax turbulence model for both steady and unsteady compressible flows. In addition, these flows may be either separated or attached. In order to apply this turbulence model to flows which may be subjected to these conditions, certain modifications should be made to the original Baldwin-Lomax model. We discuss these modifications and determine whether the Baldwin-Lomax model is a viable turbulence model that produces reasonably accurate results for high speed flows that can be found in engine inlets.
The Baldwin-Lomax model is used in many CFD codes because it is quick and easy to implement. In this paper, we discuss implementing the Baldwin-Lomax turbulence model for both steady and unsteady compressible flows. In addition, these flows may be either separated or attached. In order to apply this turbulence model to flows which may be subjected to these conditions, certain modifications should be made to the original Baldwin-Lomax model. We discuss these modifications and determine whether the Baldwin-Lomax model is a viable turbulence model that produces reasonably accurate results for high speed flows that can be found in engine inlets.
Computational fluid dynamics (CFD) has become widely used in the design and analysis of turbomachinery components such as centrifugal compressors. However, CFD is only a limited representation of experimental cases and struggles to model complex flows or can lack small model details to increase computation speed. To make advancements in compressor technology, designers need tools like CFD that can help them predict flow behavior in new designs. The High Efficiency Centrifugal Compressor (HECC) was designed by United Technologies Research Center (UTRC) for NASA to investigate the difficulties behind improving centrifugal compressor technology and to provide an open case to the turbomachinery research community. CFD analysis was completed by UTRC to aid in the design process. The pre-test study significantly overpredicted the compressor’s performance, and while post-test analysis was more representative, its results have yet to be publicly available. CFD technology has also since improved in recent years. In this study, a high-fidelity computational model for the vaneless configuration of HECC operating at its design point was developed and compared to an equivalent experimental case. This model incorporated GPU versions of mesh generation and solver codes from AeroDynamic Solutions, Inc. The development of such a model is significant since there has yet to be a published numerical simulation of HECC’s vaneless configuration. Additionally, the use of GPU codes decreases computation times for the model, which has allowed for the inclusion of impeller blade fillets. Initial results showed a general overprediction of compressor performance by the model. Predictions were more accurate for the impeller compared to predictions for the full compressor stage. Spanwise analyses showed that the model tended to follow flow behavior patterns exhibited in the experiment. Beyond this study, this model will be iterated upon and experimentally validated to further examine HECC performance.
Hybrid simulation frameworks combining Computational Fluid Dynamics (CFD) and Direct Simulation Monte Carlo (DSMC) are frequently employed to efficiently perform high-fidelity simulations of environments consisting of both continuum and rarified flow. DSMC is a stochastic, particle-based method which solves the fundamental Boltzmann equation and is therefore necessary for high-Knudsen flow where continuum-based assumptions governing CFD break down. However, the DSMC methodology is generally computationally inefficient to model the continuum regime. In a CFD/DSMC hybrid approach, obtaining an accurate, high-fidelity solution hinges on the consistent treatment of transport properties and the thermo-chemical models employed within the two solvers. In principle, in regions where CFD and DSMC are both employed, the same gas mixture under the same conditions should have the same properties, regardless of simulation type. Observed differences should be due to non-equilibrium processes, rather than differences in physical models. The goal of this work is to provide a comprehensive DSMC transport database encompassing the vast majority of known gas species encountered during Earth or other planetary atmospheric entry. This goal is largely possible due to recently performed ab initio quantum chemistry calculations. Combined with other high-fidelity data, the planned database will consist of collision integral data for over 200 neutral and ionized species and over 20000 binary collisions. From these collision integrals, Nelder-Mead optimization is used to compute collision-specific Variable Soft Sphere (VSS) collision model parameters, fitted from 300 K to 20000 K. Initial comparisons of transport properties of relevant equilibrium gas mixtures show great agreement between CFD and DSMC-derived results. The completed database can be readily applied to model binary collisions of any gas mixture containing the included species over the specified temperature range, making it a valuable tool for future planetary probe modeling efforts. An example is shown below in Fig. 1. Equilibrium mixture transport properties for a 35-species mixture composed originally of 10% air and 90% pyrolysis species of a carbon-phenolic ablator material [4] are computed using both fitted VSS Parameters and the original CFD collision integral values. Deviations in computed properties between the two approaches are less than 5% for the entire temperature range.
AdapChem software enables high efficiency, low computational cost, and enhanced accuracy on computational fluid dynamics (CFD) numerical simulations used for combustion studies. The software dynamically allocates smaller, reduced chemical models instead of the larger, full chemistry models to evolve the calculation while ensuring the same accuracy to be obtained for steady-state CFD reacting flow simulations. The software enables detailed chemical kinetic modeling in combustion CFD simulations. AdapChem adapts the reaction mechanism used in the CFD to the local reaction conditions. Instead of a single, comprehensive reaction mechanism throughout the computation, a dynamic distribution of smaller, reduced models is used to capture accurately the chemical kinetics at a fraction of the cost of the traditional single-mechanism approach.
A wind tunnel test and a computational study were conducted to investigate the complex interactions between a supersonic nozzle plume and shock waves of differing strengths generated from various aft surfaces typical of supersonic aircraft. These analytically-defined aft surfaces were representative of horizontal tails of various sizes, and an aft deck. CFD simulations of many proposed model configurations allowed for assessments of the detailed flow interactions of components in close proximity to the nozzle, as well as assessments of the nozzle jet flow itself. The evaluation of the computational results for many candidate configurations guided the design of model components. The interactions of the waveforms from these surfaces with the jet exhaust plume can have significant adverse effects on the loudness of the sonic boom if the surfaces are not carefully integrated into an aircraft design. The greatest discrepancy in estimating sonic boom loudness for low-boom flight vehicles is currently in predicting the signatures from the aft part of an aircraft, including the interactions with the plume flow. The objectives of this test were to gain a better understanding of these interactions, and to provide a detailed experimental database from multiple sources for use as validation cases for CFD tool development. The subject test was run in the NASA Ames 9- by 7-Ft Supersonic Wind Tunnel in February 2016 at Mach numbers of 1.6 and 2.0, and was funded by the NASA Commercial Supersonics Technology (CST) Project. The nozzle flow was provided by high-pressure air (HPA) pumped through the model, and pressure signature data were acquired with the NASA 14-inch sonic boom pressure rail. The rail measured the locations of the shocks and expansions at various distances and off-track angles from the model. This enabled the impact of the nozzle plume/shock interactions on the near- and mid-field sonic boom pressure waveforms to be quantified. Schlieren images of the flow field around and behind the model were obtained with an RBOS (Retroreflective Background-Oriented Schlieren) technique to determine the origins of the shock and expansion waves, to identify the shape and boundaries of the plume, and to determine the changes in incoming and exiting waveforms within the plume. A total pressure rake was positioned closely behind the model nozzle in order to measure the total pressure profiles of the flow above, within, and below the nozzle exhaust. Model angles and positions in the tunnel were measured by photogrammetry using two cameras since the lack of a model force balance prevented the measurement of model deflections under load.Navier-Stokes computations using two different CFD codes were compared to the experimental sonic boom pressure signature data, and the rake total pressure data in the plume. A computational schlieren technique was used to compare the computed flow field with the RBOS images. The computational results were also used to complement the test data with flow field quantities that could not be measured, such as Mach number and pressure distributions to distinguish shock waves and expansion waves.
The NASA Lewis Research Center, in conjunction with the University of Akron, is developing analytical methods and software tools to create a cross-discipline "bridge" between controls and computational fluid dynamics (CFD) technologies. Traditionally, the controls analyst has used simulations based on large lumping techniques to generate low-order linear models convenient for designing propulsion system controls. For complex, high-speed vehicles such as the High Speed Civil Transport (HSCT), simulations based on CFD methods are required to capture the relevant flow physics. The use of CFD should also help reduce the development time and costs associated with experimentally tuning the control system. The initial application for this research is the High Speed Civil Transport inlet control problem. A major aspect of this research is the development of a controls/CFD interface for non-CFD experts, to facilitate the interactive operation of CFD simulations and the extraction of reduced-order, time-accurate models from CFD results. A distributed computing approach for implementing the interface is being explored. Software being developed as part of the Integrated CFD and Experiments (ICE) project provides the basis for the operating environment, including run-time displays and information (data base) management. Message-passing software is used to communicate between the ICE system and the CFD simulation, which can reside on distributed, parallel computing systems. Initially, the one-dimensional Large-Perturbation Inlet (LAPIN) code is being used to simulate a High Speed Civil Transport type inlet. LAPIN can model real supersonic inlet features, including bleeds, bypasses, and variable geometry, such as translating or variable-ramp-angle centerbodies. Work is in progress to use parallel versions of the multidimensional NPARC code.
Autogenous pressurization of cryogenic propellant tanks eliminates the need to have an additional pressurant tank on the space vehicle, which is highly advantageous due to reduced vehicle mass and design complexity. Autogenous pressurization therefore is one of the key technologies for deep space exploration and long-term space missions. The complex interaction of thermal gradients, turbulence and phase change near the interface make the problem a challenging one to model. Nodal analysis tools and reduced order models are unable to capture the necessary physics. 3-D CFD analyses are necessary to fully characterize autogenous pressurization. CFD analyses pose their own difficulties. The requisite CFD tool to tackle this problem need to be modular with the ability to incorporate various physics models, efficient, and computationally scalable for simulating flight size tanks. NASA MSFC's Loci-Stream CFD tool along with the VOF module is a great candidate to fit this mold. We demonstrate our modeling approach and validation of Loci-Stream for predicting autogenous pressurization of a flight scale propellant tank in order for the solver to serve as a reliable design and analysis tool for NASA's CFM application needs. Liquid hydrogen tank pressurization tests carried out at the MSFC test stand 300 facilities provide reliable validation data for this purpose. These tests were modeled using the Loci-Stream solver with a newly implemented two-phase sharp interface treatment. We show that our modeling approach and CFD solver predict the autogenous pressurization phenomena satisfactorily, and document challenging aspects of modeling this problem.
A new model for the surface chemistry of zirconium and hafnium diborides containing silicon-carbide when exposed to high temperature conditions in air is formulated. Oxidation dynamics are simplified by considering the diffusion-limited equilibrium regime within the material at elevated temperatures. This model is first assessed against experimental mass-gain data taken from UHTC samples heated to high temperature in an oxygen environment. Then, further evaluations of the new model are conducted using hypersonic CFD simulations to analyze conditions experienced by HfB2-SiC in arc jet experiments conducted at NASA Ames Research Center. Measurements of stagnation point heat transfer and pressure are then used to calibrate the simulations. Results of coupled CFD-material response simulations are then compared to the surface temperatures measured during the Ames arc jet test. Results support the use of the proposed model while highlighting the need for improved gas-phase data on the additional constituents considered.
This paper reports computational analyses of tests in a high enthalpy arc-jet facility at NASA Ames Research Center. These tests were conducted using 23.6-cm diameter, 55° sphere-cone models placed in a free jet downstream of the 33.0-cm diameter conical nozzle in the 60-MW Interaction Heating Facility. Some of the sphere-cone models include surface features such as manufactured fences and gaps intended to simulate effects of differential recession, all of which disturb the flow, producing augmented heating locally and downstream. Test calibration data were obtained using slug and Gardon gage stagnation calorimeters, and a sphere-cone calorimeter model with six Gardon heat flux gages and five pressure gages. The present analysis comprises computational fluid dynamics simulations of the nonequilibrium flowfield in the facility nozzle and test box, including the models tested, and comparisons with the experimental measurements. Various issues related to testing are considered: diffuser flow capture, flow characterization based on the calorimeter data, effects of the model surface recession, and prediction of surface quantities for the models with surface features. These simulations take into account nonuniform total enthalpy profiles at the nozzle inlet as well as the expansion waves emanating from the nozzle exit and their effects on the model flowfields.
A study conducting bouyancy driven convective flow experiments on the NASA KC-135 aircraft is presented. The response of a contained fluid (with an imposed temperature gradient) to changing g-levels during parabolic flight was obtained. Models for both transient and steady state flows were developed utilizing PC-based CFD software. Comparisons between the theoretical models and the physical observations are quite good.