SEARCH · Engineering Papers

Results for “Base Line”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40

All sources NASA NTRS DOE OSTI

NASA NTRS1992

Adaptive low-bandwidth tracking of Galileo and Pioneer 10 carriers

In the Deep Space Network, tracking of residual carrier phase typically occurs with a fixed-bandwidth phase-locked loop using a bandwidth sufficiently wide to prevent loss of lock under worst-case conditions of signal dynamics, received signal phase noise, and receiver phase noise. Much of the time, however, such a high bandwidth is not required and may inflict unnecessarily heavy penalties on loop signal-to-noise ratios. This article describes a technique for improving tracking performance by permitting initial tracking at narrow bandwidths and gradually widening the loop as needed. The cost is a requirement for signal buffering, which is relatively inexpensive for low data rate applications. Results based on off-line processing of recorded carrier data from Galileo and Pioneer 10 are presented, and show potential 10-16 dB gains in loop SNR over worst-case fixed-bandwidth tracking.

Watola, D. A.↗

NASA NTRS1993

Estimating turbine limit load

A method for estimating turbine limit-load pressure ratio from turbine map information is presented and demonstrated. It is based on a mean line analysis at the last-rotor exit. The required map information includes choke flow rate at all speeds as well as pressure ratio and efficiency at the onset of choke at design speed. One- and two-stage turbines are analyzed to compare the results with those from a more rigorous off-design flow analysis and to show the sensitivities of the computed limit-load pressure ratios to changes in the key assumptions.

Glassman, Arthur J.↗

NASA NTRS1992

Friction-factor data for flat-plate tests of smooth and honeycomb surfaces

Friction factors for honeycomb surfaces were measured with a flat plate tester. The flat plate test apparatus was described and a method was discussed for determining the friction factor experimentally. The friction factor model was developed for the flat plate test based on the Fanno Line Flow. The comparisons of the friction factor were plotted for smooth surfaces and six-honeycomb surfaces with three-clearances, 6.9 bar to 17.9 bar range of inlet pressures, and 5,000 to 100,000 range of the Reynolds number. The optimum geometries for the maximum friction factor were found as a function of cell width to cell depth and cell width to clearance ratios.

Ha, T. W.↗

NASA NTRS1993

Photometric and spectroscopic observations of SN 1990E in NGC 1035 - Observational constraints for models of type II supernovae

We present 126 photometric and 30 spectral observations of SN 1990E spanning from 12 days before B maximum to 600 days past discovery. These observations show that SN 1990E was of type II-P, displaying hydrogen in its spectrum, and the characteristic plateau in its light curve. SN 1990E is one of the few SNe II which has been well observed before maximum light, and we present evidence that this SN was discovered very soon after its explosion. In the earliest spectra we identify, for the first time, several N II lines. We present a new technique for measuring extinction to SNe II based on the evolution of absorption lines, and use this method to estimate the extinction to SN 1990E, A(V) = 1.5 +/- 0.3 mag. From our photometric data we have constructed a bolometric light curve for SN 1990E and show that, even at the earliest times, the bolometric luminosity was failing rapidly. We use the late-time bolometric light curve to show that SN 1990E trapped a majority of the gamma rays produced by the radioactive decay of Co-56, and estimate that SN 1990E ejected an amount of Ni-56 virtually identical to that of SN 1987A.

Schmidt, Brian P.↗

NASA NTRS1954

Method for calculating the rolling and yawing moments due to rolling for unswept wings with or without flaps or ailerons by use of nonlinear section lift data

The methods of NACA reports 865 and 1090 have been applied to the calculation of the rolling-moment and yawing-moment coefficients due to rolling for unswept wings with or without flaps or ailerons. The methods are based on lifting-line theory and allow the use of nonlinear section lift data. The method presented in this report permits calculations to be made somewhat beyond maximum lift for wings having no twist or continuous twist and employing airfoil sections which do not display large discontinuities in the lift curves. Calculations can be made up to maximum lift for wings with discontinuous twist such as that produced by partial-span flaps or ailerons, or both. Two calculated examples are presented in simplified computing forms in order to illustrate the procedures involve.

Martina, Albert P↗

NASA NTRS1994

Extinction, ejecta masses, and radial velocities of novae

Interstellar reddening is determined for a number of recent novae based upon emission-line ratios which are generally observable using CCDs. Large values of extinction are found for most systems, possibly indicative of an intrinsic component of reddening in postoutburst novae. The unusual characteristics of the (O I) lines in novae, which are strong and optically thick, require a large population of very dense globules which are the likely sites of dust formation. These pyroclasts must be ejected from the white dwarf. The total mass of the neutral gas in the globules in some of the objects is substantially larger than the masses normally derived for the ionized ejecta of novae. The distribution of radial velocities of Galactic novae in the Tololo sample, although uncertain, shows an asymmetry in having predominantly negative values. Either high internal absorption in the expanding ejecta skews the emission lines to bluer wavelengths, or most of the novae are moving out from the center of the Galaxy.

Williams, Robert E.↗

NASA NTRS1995

Hubble Space Telescope high resolution spectroscoy of the exposed white dwarf in the dwarf nova VW Hydri in quiescence: A rapidly rotating white dwarf

We obtained a far-ultraviolet spectrum of the dwarf nova VW Hyi in quiescence, with the Hubble Space Telescope Goddard High Resolution Spectrograph covering the region of the Si iv lambda(lambda)1393, 1402 resonance doublet. The broad, shallow Si iv doublet feature is fully resolved, has a total equivalent width of 2.8 A, and is the first metal absorption feature to be clearly detected in the exposed white dwarf. Our synthetic spectral analysis, using a model grid constructed with the code TLUSTY, resulted in a reasonable fit to a white dwarf photosphere with T(sub eff) = 22,000 +/- 2000 K, log g = 8.0 +/- 0.3, an approximately solar Si/H abundance, and a rotational velocity, v sin i approximately equal to 600 km/s. This rotation rate, while not definitive because it is based upon just one line transition, is 20% of the Keplerian (breakup) velocity of the white dwarf and hence does not account for the unexpectedly low boundary-layer luminosity inferred from the soft-X-ray/extreme ultra-violet bands where most of the boundary-layer luminosity should be radiated. The predicted boundary-layer luminosity for a 0.6 solar mass white dwarf accreting at the rate 10(exp -10) solar mass/yr and rotating at 600 km/s, corresponding to VW Hyi in quiescence, is 2 x 10(exp 32) ergs/s when proper account is taken of the rotational kinetic energy going into spinning up the white dwarf. If the boundary-layer area is equal to that of the white dwarf, then T(sub bl) = 24,000 K. This is essentially identical to the photspheric luminosity and temperature determined in far-ultraviolet photospheric analyses. If the boundary-layer area is 10(exp -3) of the white dwarf surface area, then T(sub bl) = 136,000 K.

Sion, Edward M.↗

NASA NTRS1996

Feasibility Study of a Rotorcraft Health and Usage Monitoring System ( HUMS): Usage and Structural Life Monitoring Evaluation

The objective of this study was to evaluate two techniques, Flight Condition Recognition (FCR) and Flight Load Synthesis (FLS), for usage monitoring and assess the potential benefits of extending the retirement intervals of life-limited components, thus reducing the operator's maintenance and replacement costs. Both techniques involve indirect determination of loads using measured flight parameters and subsequent fatigue analysis to calculate the life expended on the life-limited components. To assess the potential benefit of usage monitoring, the two usage techniques were compared to current methods of component retirement. In addition, comparisons were made with direct load measurements to assess the accuracy of the two techniques. The data that was used for the evaluation of the usage monitoring techniques was collected under an independent HUMS Flight trial program, using a commercially available HUMS and data recording system. The usage data collect from the HUMS trial aircraft was analyzed off-line using PC-based software that included the FCR and FLS techniques. In the future, if the technique prove feasible, usage monitoring would be incorporated into the onboard HUMS.

Dickson, B.↗

NASA NTRS1996

Occurrency frequency of substorm field and plasma signatures observed near-earth by ISEE-1/2

The onset of the majority of substorms occurs when the tail field stops growing more tail-like and begins to become more dipolar. This corresponds to the onset signatures on the ground and in geosynchronous orbit. The AE indices and the IGS Pi 2 data were used to determine the major substorm onsets of 1978 and 1979. The time delay between successive substorms, the distribution of the substorm growth phase duration and the probability of tailward flows were determined as a function of spacecraft location. About a half of the substorms exhibit a plasma signature including earthward or tailward flows or plasma sheet drop out and recovery. Earthward flows are often seen at substorm onset, and almost always during substorm recovery. Tailward flows are occasionally seen at onset as the spacecraft is close enough to the neutral sheet. The experimental results are compared to predictions based on the neutral line and current sheet disruption models.

Hsu, T. S.↗

NASA NTRS1998

Robust Multigrid Smoothers for Three Dimensional Elliptic Equations with Strong Anisotropies

We discuss the behavior of several plane relaxation methods as multigrid smoothers for the solution of a discrete anisotropic elliptic model problem on cell-centered grids. The methods compared are plane Jacobi with damping, plane Jacobi with partial damping, plane Gauss-Seidel, plane zebra Gauss-Seidel, and line Gauss-Seidel. Based on numerical experiments and local mode analysis, we compare the smoothing factor of the different methods in the presence of strong anisotropies. A four-color Gauss-Seidel method is found to have the best numerical and architectural properties of the methods considered in the present work. Although alternating direction plane relaxation schemes are simpler and more robust than other approaches, they are not currently used in industrial and production codes because they require the solution of a two-dimensional problem for each plane in each direction. We verify the theoretical predictions of Thole and Trottenberg that an exact solution of each plane is not necessary and that a single two-dimensional multigrid cycle gives the same result as an exact solution, in much less execution time. Parallelization of the two-dimensional multigrid cycles, the kernel of the three-dimensional implicit solver, is also discussed. Alternating-plane smoothers are found to be highly efficient multigrid smoothers for anisotropic elliptic problems.

Llorente, Ignacio M.↗

NASA NTRS1999

Ammonia Monitor

Ammonia monitor and method of use are disclosed. A continuous, real-time determination of the concentration of ammonia in an aqueous process stream is possible over a wide dynamic range of concentrations. No reagents are required because pH is controlled by an in-line solid-phase base. Ammonia is selectively transported across a membrane from the process stream to an analytical stream to an analytical stream under pH control. The specific electrical conductance of the analytical stream is measured and used to determine the concentration of ammonia.

Sauer, Richard L.↗

NASA NTRS1999

Streamer Brightness Boundary

Flow tubes adjacent to closed magnetic field lines on the boundaries of streamers can have spreading factors which change rapidly with height. Numerical models in this thin layer are subject to uncertainties. Here we use an analytic model of magnetically closed and adjacent open regions to analyze the spreading factor close to the closed field lines. The model is based on the one-temperature, isothermal flow model of Pneuman (1968), extended to calculate spreading factors and plasma beta, and to better explain streamer evolution with increasing temperature.

Suess, S. T.↗

NASA NTRS2000

A Real-Time High Performance Data Compression Technique For Space Applications

A high performance lossy data compression technique is currently being developed for space science applications under the requirement of high-speed push-broom scanning. The technique is also error-resilient in that error propagation is contained within a few scan lines. The algorithm is based on block-transform combined with bit-plane encoding; this combination results in an embedded bit string with exactly the desirable compression rate. The lossy coder is described. The compression scheme performs well on a suite of test images typical of images from spacecraft instruments. Hardware implementations are in development; a functional chip set is expected by the end of 2001.

Yeh, Pen-Shu↗

NASA NTRS2000

Application of Three-Component PIV to a Hovering Rotor Wake

The key to accurate predictions of rotorcraft aerodynamics, acoustics, and dynamics lies in the accurate representation of the rotor wake. The vortical wake computed by rotorcraft CFD analyses typically suffer from numerical dissipation before the first blade passage. With some a priori knowledge of the wake trajectory, grid points can be concentrated along the trajectory to minimize the dissipation. Comprehensive rotorcraft analyses based on lifting-line theory rely on classical vortex models and/or semi-empirical information about the tip vortex structure. Until the location, size, and strength of the trailed tip vortex can be measured over a range of wake ages, the analyses will continue to be adjusted on a trial and error basis in order to correctly predict blade airloads, acoustics, dynamics, and performance. Using the laser light sheet technique, tip vortex location can be acquired in a straightforward manner. Measuring wake velocities and vortex core size, however, has been difficult and tedious using point-measurement techniques such as laser velocimetry. Recently, the Particle Image Velocimetry (PIV) technique has proven to be an efficient method for acquiring velocity measurements over relatively large areas and volumes of a rotor wake. The work reported to date, however, has been restricted to 2-component velocity measurements of the rotor wake. Three-component velocity measurements of a hovering rotor wake were acquired at NASA Ames Research Center in May 1999. This experiment represents a major step toward understanding the detailed structure of a rotor wake. This paper will focus primarily on the experimental technique used in acquiring this data. The accuracy and limitations of the current technique will also be discussed. Representative velocity field measurements will be included.

Yamauchi, Gloria K.↗

NASA NTRS2003

Overview of NASA's space radiation research program

NASA is developing the knowledge required to accurately predict and to efficiently manage radiation risk in space. The strategy employed has three research components: (1) ground-based simulation of space radiation components to develop a science-based understanding of radiation risk; (2) space-based measurements of the radiation environment on planetary surfaces and interplanetary space, as well as use of space platforms to validate predictions; and, (3) implementation of countermeasures to mitigate risk. NASA intends to significantly expand its support of ground-based radiation research in line with completion of the Booster Applications Facility at Brookhaven National Laboratory, expected in summer of 2003. A joint research solicitation with the Department of Energy is under way and other interagency collaborations are being considered. In addition, a Space Radiation Initiative has been submitted by the Administration to Congress that would provide answers to most questions related to the International Space Station within the next 10 years.

NASA Discipline Radiation Health↗

NASA NTRS2004

Mesoscale Simulations of CRYSTAL-FACE 23 July 2002 Case

A key objective of the Cirrus Regional Study of Tropical Anvils and Cirrus Layers - Florida Area Cirrus Experiment (CRYSTAL-FACE) is to understand the relationships between properties of tropical convective cloud systems and the lifecycle of the extended cirrus anvils they produce. We report here on a case study of 23 July 2002 where a line of land-based convective storms was generated between Lake Okeechobee and the Florida east coast as a result of complex interactions between lake and sea breeze fronts and outflow boundaries. A central goal of this study is to develop a description of convective input to the anvil system and to quantify the ongoing dynamical forcing of anvil processes by mesoscale and large-scale dynamics. This information is then used to force high-resolution cloud simulations with a model that explicitly resolves cloud microphysical processes (bin model) for study of cirrus anvil microphysical development.

Starr, David↗

NASA NTRS2004

Accident Precursor Analysis and Management: Reducing Technological Risk Through Diligence

Almost every year there is at least one technological disaster that highlights the challenge of managing technological risk. On February 1, 2003, the space shuttle Columbia and her crew were lost during reentry into the atmosphere. In the summer of 2003, there was a blackout that left millions of people in the northeast United States without electricity. Forensic analyses, congressional hearings, investigations by scientific boards and panels, and journalistic and academic research have yielded a wealth of information about the events that led up to each disaster, and questions have arisen. Why were the events that led to the accident not recognized as harbingers? Why were risk-reducing steps not taken? This line of questioning is based on the assumption that signals before an accident can and should be recognized. To examine the validity of this assumption, the National Academy of Engineering (NAE) undertook the Accident Precursors Project in February 2003. The project was overseen by a committee of experts from the safety and risk-sciences communities. Rather than examining a single accident or incident, the committee decided to investigate how different organizations anticipate and assess the likelihood of accidents from accident precursors. The project culminated in a workshop held in Washington, D.C., in July 2003. This report includes the papers presented at the workshop, as well as findings and recommendations based on the workshop results and committee discussions. The papers describe precursor strategies in aviation, the chemical industry, health care, nuclear power and security operations. In addition to current practices, they also address some areas for future research.

Phimister, James R.↗

NASA NTRS2006

Turbopump Design and Analysis Approach for Nuclear Thermal Rockets

A rocket propulsion system, whether it is a chemical rocket or a nuclear thermal rocket, is fairly complex in detail but rather simple in principle. Among all the interacting parts, three components stand out: they are pumps and turbines (turbopumps), and the thrust chamber. To obtain an understanding of the overall rocket propulsion system characteristics, one starts from analyzing the interactions among these three components. It is therefore of utmost importance to be able to satisfactorily characterize the turbopump, level by level, at all phases of a vehicle design cycle. Here at NASA Glenn Research Center, as the starting phase of a rocket engine design, specifically a Nuclear Thermal Rocket Engine design, we adopted the approach of using a high level system cycle analysis code (NESS) to obtain an initial analysis of the operational characteristics of a turbopump required in the propulsion system. A set of turbopump design codes (PumpDes and TurbDes) were then executed to obtain sizing and performance characteristics of the turbopump that were consistent with the mission requirements. A set of turbopump analyses codes (PUMPA and TURBA) were applied to obtain the full performance map for each of the turbopump components; a two dimensional layout of the turbopump based on these mean line analyses was also generated. Adequacy of the turbopump conceptual design will later be determined by further analyses and evaluation. In this paper, descriptions and discussions of the aforementioned approach are provided and future outlooks are discussed.

Chen, Shu-cheng S.↗