Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Aerodynamic Heating”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 721 records · Page 40
All sourcesNASA NTRSDOE OSTI
NASA NTRS1965

Evaluation of materials in entry heating simulation

The effects of several environmental parameters on the behavior of ablation materials have been examined. Practically all the entry heating parameters such as enthalpy, pressure, heating rate, aerodynamic shear, and so forth, affect material performance. However, the significance of the effects depends to a large extent upon the type of material. Inasmuch as it is rarely possible to simulate several environment effects simultaneously, the primary inputs must be determined and the test simulation must account for the effects of these inputs. The particular materials of concern must be characterized by test and analysis to determine which of the many environmental inputs are the most significant.

Simulation↗
NASA NTRS1992

Physiologically constrained aerocapture for manned Mars missions

Aerobraking has been proposed as a critical technology for manned missions to Mars. The variety of mission architectures currently under consideration presents aerobrake designers with an enormous range of potential entry scenarios. Two of the most important considerations in the design of an aerobrake are the required control authority (lift-to-drag ratio) and the aerothermal environment which the vehicle will encounter. Therefore, this study examined the entry corridor width and stagnation-point heating rate and load for the entire range of probable entry velocities, lift-to-drag ratios, and ballistic coefficients for capture at both Earth and Mars. To accomplish this, a peak deceleration limit for the aerocapture maneuvers had to be established. Previous studies had used a variety of load limits without adequate proof of their validity. Existing physiological and space flight data were examined, and it was concluded that a deceleration limit of 5 G was appropriate. When this load limit was applied, numerical studies showed that an aerobrake with an L/D of 0.3 could provide an entry corridor width of at least 1 degree for all Mars aerocaptures considered with entry velocities up to 9 km/s. If 10 km/s entries are required, an L/D of 0.4 to 0.5 would be necessary to maintain a corridor width of at least 1 degree. For Earth return aerocapture, a vehicle with an L/D of 0.4 to 0.5 was found to provide a corridor width of 0.7 degree or more for all entry velocities up to 14.5 km/s. Aerodynamic convective heating calculations were performed assuming a fully catalytic, 'cold' wall; radiative heating was calculated assuming that the shock layer was in thermochemical equilibrium. Heating rates were low enough for selected entries at Mars that a radiatively cooled thermal protection system might be feasible, although an ablative material would be required for most scenarios. Earth return heating rates were generally more severe than those encountered by the Apollo vehicles, and would require ablative heat shields in all cases.

Lyne, James Evans↗
DOE OSTI2021

Hard x-ray methods for studying the structure of amorphous thin films and bulk glassy oxides

High-energy photon diffraction minimizes many of the corrections associated with laboratory x-ray diffractometers, and enables structure factor measurements to be made over a wide range of momentum transfers. The method edges us closer toward an ideal experiment, in which coordination numbers can be extracted without knowledge of the sample density. Three case studies are presented that demonstrate new hard x-ray methods for studying the structure of glassy and amorphous materials. First, the methodology and analysis of high-energy grazing incidence on thin films is discussed for the case of amorphous In 2 O 3 . Additionally, the connectivity of irregular InO 6 polyhedra are shown to exist in face-, edge- and corner-shared configurations in the approximate ratio of 1:2:3. Secondly, the technique of high-energy small and wide angle scattering has been carried out on laser heated and aerodynamically levitated samples of silica-rich barium silicate (20BaO:80SiO 2 ), from the single phase melt at 1500 C-o to the phase separated glass at room temperature. Based on Ba-O coordination numbers of 6 to 7, it is argued that the although the potential of Ba is ionic, it is weak enough to cause the liquid-liquid immiscibility to become metastable. Lastly, high-energy small and wide angle scattering has also been applied to high water content (up to 12 wt.%) samples of hydrous SiO 2 glass quenched from 1500 C-o at 4 GPa. An increase of Si 1 O 2 correlations at 4.3 angstrom is found to be consistent with an increase in the population of three-membered SiO 4 rings at the expense of larger rings.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Turbine Aero-Thermal Technologies for 65% Combined Cycle Efficiency (Phase I Final Report)

GE Power (GEP), a division of General Electric Company, performed a gas turbine technology development program that integrated Aerodynamic and Heat Transfer advances as an important and innovative step towards the DOE goal of 65% combined cycle efficiency. Improved efficiency will also contribute towards the reduction in the cost of electricity identified by the DOE for the US through reduced fuel consumption, and through lowering the capital cost of the generating equipment. It is currently predicted that the result of this project will enable 0.40~0.65 pt in combined cycle efficiency improvement. This technology will be directly applicable to gas turbines utilizing coal gasification processes where hydrogen-rich coal-derived synthesis gas is produced with natural gas being the developmental fuel.

03 NATURAL GAS↗
NASA NTRS1962

Predicted Gas Properties in the Shock Layer Ahead of Capsule-Type Vehicles at Angles of Attack

A method for determining shock-wave shapes, stagnation-point location, and flow-field properties for spherically blunt bodies at angle of attack was developed. The method is applicable to perfect gas flows and equilibrium flow of real gases. The results given by the method for shock surface and stagnation-point location are compared with experimental values. Comparison of the shock-layer density and temperature distribution are also made between the results of the method and those of a more exact procedure for a sphere. These comparisons indicate satisfactory agreement.

REENTRY↗
NASA NTRS1962

Free-Flight Tests of Fifth-Stage Scout Entry Vehicle at Mach Numbers of 5 and 17

Measurements have been made in air at two Mach numbers of the static stability, normal force, and drag of a version of the fifth-stage Scout entry vehicle. The most significant result was that the design center of gravity led to a condition of static instability at small angles of attack at Mach number 17. At this Mach number, the static stability was a highly nonlinear function of the angle of attack. A useful method for analyzing free-flight data having this nonlinear behavior is included in this report. Comparisons were made between the measured aerodynamic coefficients and those estimated by Newtonian impact theory and by a method developed by Seiff and Whiting. The latter method gave good estimates of the normal-force-curve slope at both Mach numbers and of the moment-curve slope at the lower Mach number. It resulted in an overestimation of the static stability at Mach number 17, although it gave results decidedly closer to the experimental value than did Newtonian impact theory.

FREE FLIGHT↗
NASA NTRS1958

Structural design considerations for boost-glide and orbital reentry vehicles

The preceding papers have discussed the aerodynamics and heating of several vehicles designed for atmospheric reentry from satellite orbits. Because of large heating inputs, some fundamental questions about the structure of these vehicles are also raised. Although there are many factors which influence structural design, only a brief examination of the relationship between heating input and structural weight is discussed here. For this purpose the heating inputs associated with the four vehicles shown in figure 1 are employed.

William A. Brooks, Jr.↗