Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “yaw control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

Experimental study of tail-span effects on a generic canard-controlled missile

An experimental investigation was conducted on a cruciform canard controlled missile configuration to determine the effects of tail span/canard span ratio on controllability. The investigation was conducted over the Mach number range of 1.75 to 3.50. Reductions of tail span/canard span ratio produced lower static margins and higher trim angle of attack. The results show that canard controls can provide pitch- and yaw-control as well as roll-control by proper selection of the tail span/canard span ratio.

Blair, A. B., Jr.↗
NASA NTRS1994

Comparison of full-scale, small-scale, and CFD results for F/A-18 forebody slot blowing

It has been shown experimentally that forebody flow control devices provide a significant increase in yaw control for fighter aircraft at high angle-of-attack. This study presents comparisons of the various experimental and computational results for tangential slot blowing on the F/A-18 configuration. Experimental results are from the full-scale and 6 percent-scale model test and computational solutions are from both isolated forebody and and full aircraft configurations. The emphasis is on identifying trends in the variation of yawing moment with blowing-slot exit conditions. None of the traditional parameters (mass flow ratio, blowing momentum coefficient, velocity ratio) succeeded in collapsing all of the results into a common curve. Several factors may effect the agreement between the 6 percent- and full-scale results including Reynolds number effects, sensitivity of boundary layer transition from laminar to turbulent flow, and poor geometric fidelity, particularly of the blowing slot. The disagreement between the full-scale and computed yawing moments may be due to a mismatch in the slot exit conditions for the same mass flow ratio or aircraft configuration modeling. The general behavior of slot blowing on the 6 percent-scale and computational models is correct, but neither matches the full-scale results.

Lanser, Wendy R.↗
NASA NTRS1979

Longitudinal and lateral static stability and control characteristics of a 1/6-scale model of a remotely piloted research vehicle with a supercritical wing

An investigation was conducted in the Langley 8-foot transonic pressure tunnel to determine the longitudinal and lateral-directional static stability and control characteristics of a 1/6-scale force model of a remotely piloted research vehicle. The model was equipped with a supercritical wing and employed elevons for pitch and roll control. Test conditions were as follows: Reynolds number of about 6.6 x 10 to the 6th power per meter, variations of sideslip from -6 deg to 6 deg, elevon deflection angle (symmetrically and asymmetrically) from -9 deg to 3 deg, and rudder deflection angle from 0 deg to -10 deg. The model was longitudinally statically stable at angles of attack up to about 7 deg, which is significantly greater than the angle of attack for the cruise condition (approximately 4 deg). In the range of test Mach numbers, the model was directionally stable and had positive effective dihedral, sufficient pitch control, and positive effectiveness of roll and yaw control.

Byrdsong, T. A.↗
NASA NTRS1995

Sailplane Glide Performance and Control Using Fixed and Articulating Winglets

An experimental study was conducted to investigate the effects of controllable articulating winglets on glide performance and yawing moments of high performance sailplanes. Testing was conducted in the Texas A&M University 7 x 10 foot Low Speed Wind Tunnel using a full-scale model of the outboard 5.6 feet of a 15 meter class high performance sailplane wing. Different wing tip configurations could be easily mounted to the wing model. A winglet was designed in which the cant and toe angles as well as a rudder on the winglet could be adjusted to a range of positions. Cant angles used in the investigation consisted of 5, 25, and 40 degrees measured from the vertical axis. Toe-out angles ranged from 0 to 22.5 degrees. A rudder on the winglet was used to study the effects of changing the camber of the winglet airfoil on wing performance and wing yawing moments. Rudder deflections consisted of-10, 0, and 10 degrees. Test results for a fixed geometry winglet and a standard wing tip are presented to show the general behavior of winglets on sailplane wings, and the effects of boundary-layer turbulators on the winglets are also presented. By tripping the laminar boundary-layer to turbulent before laminar separation occurs, the wing performance was increased at low Reynolds numbers. The effects on the lift and drag, yawing moment, pitching moment, and wing root bending moment of the model are presented. Oil flows were used on the wing model with the fixed geometry winglet and the standard wing tip to visualize flow directions and areas of boundary layer transition. A cant angle of 25 degrees and a toe-out angle of 2.5 degrees provided an optimal increase in wing performance for the cant and toe angles tested. Maximum performance was obtained when the winglet rudder remained in the neutral position of zero degrees. By varying the cant, toe, and rudder angles from their optimized positions, wing performance decreases. Although the winglet rudder proved to be more effective in increasing the yawing moment compared to varying the cant and toe angles, the amount of increased yawing moment was insignificant when compared to that produced by the vertical tail. A rudder on the winglet was determined to be ineffective for providing additional yaw control.

Colling, James David↗
NASA NTRS1995

Low-speed wind-tunnel investigation of the stability and control characteristics of a series of flying wings with sweep angles of 50 deg

A wind-tunnel investigation was conducted in the Langley 12-Foot Low-Speed Tunnel to study the low-speed stability and control characteristics of a series of four flying wings over an extended range of angle of attack (-8 deg to 48 deg). Because of the current emphasis on reducing the radar cross section (RCS) of new military aircraft, the planform of each wing was composed of lines swept at a relatively high angle of 50 deg, and all the trailing-edge lines were aligned with one of the two leading edges. Three arrow planforms with different aspect ratios and one diamond planform were tested. The models incorporated leading-edge flaps for improved longitudinal characteristics and lateral stability and had trailing-edge flaps in three segments that were deflected differentially for roll control, symmetrically for pitch control, and in a split fashion for yaw control. Three top body widths and two sizes of twin vertical tails were also tested on each model. A large aerodynamic database was compiled that could be used to evaluate some of the trade-offs involved in the design of a configuration with a reduced RCS and good flight dynamic characteristics.

Fears, Scott P.↗
NASA NTRS1995

Low-speed wind-tunnel investigation of the stability and control characteristics of a series of flying wings with sweep angles of 70 deg

A wind-tunnel investigation was conducted in the Langley 12-Foot Low-Speed Tunnel to study the low-speed stability and control characteristics of a series of four flying wings over an extended range of angle of attack (-8 deg to 48 deg). Because of the current emphasis on reducing the radar cross section (RCS) of new military aircraft, the planform of each wing was composed of lines swept at a relatively high angle of 70 deg, and all the trailing edges and control surface hinge lines were aligned with one of the two leading edges. Three arrow planforms with different aspect ratios and one diamond planform were tested. The models incorporated leading-edge flaps for improved longitudinal characteristics and lateral stability and had three sets of trailing-edge flaps that were deflected differentially for roll control, symmetrically for pitch control, and in a split fashion for yaw control. Three top body widths and two sizes of twin vertical tails were also tested on each model. A large aerodynamic database was compiled that could be used to evaluate some of the trade-offs involved in the design of a configuration with a reduced RCS and good flight dynamic characteristics.

Ross, Holly M.↗
NASA NTRS1995

Low-speed wind tunnel investigation of the stability and control characteristics of a series of flying wings with sweep angles of 60 deg

A wind tunnel investigation was conducted in the Langley 12-Foot Low-Speed Wind Tunnel to study the low-speed stability and control characteristics of a series of four flying wings over an extended range of angle of attack (-8 deg to 48 deg). Because of the current emphasis on reducing the radar cross section of new military aircraft, the planform of each wing was composed of lines swept at a relatively high angle of 60 deg, and all the trailing-edge lines were aligned with one of the two leading edges. Three arrow planforms with different aspect ratios and one diamond planform were tested. The models incorporated leading-edge flaps for improved pitching-moment characteristics and lateral stability and had three sets of trailing-edge flaps that were deflected differentially for roll control, symmetrically for pitch control, and in a split fashion for yaw control. Top bodies of three widths and twin vertical tails of various sizes and locations were also tested on each model. A large aerodynamic database was compiled that could be used to evaluate some of the trade-offs involved in the design of a configuration with a reduced radar cross section and good flight dynamic characteristics.

Moul, Thomas M.↗
NASA NTRS1992

X-29 vortex flow control tests

A joint Air Force/NASA X-29 aircraft program to improve yaw control at high angle of attack using vortex flow control (VFC) is described. Directional VFC blowing proved to a be a powerful yaw moment generator and was very effective in overriding natural asymmetries, but was essentially ineffective in suppressing wing rock. Symmetric aft blowing also had little effect on suppressing wing rock.

Hancock, Regis↗
NASA NTRS1991

Forebody tangential blowing for control at high angles of attack

A feasibility study to determine if the use of tangential leading edge blowing over the forebody could produce effective and practical control of the F-18 HARV aircraft at high angles of attack was conducted. A simplified model of the F-18 configuration using a vortex-lattice model was developed to obtain a better understanding of basic aerodynamic coupling effects and the influence of forebody circulation on lifting surface behavior. The effect of tangential blowing was estimated using existing wind tunnel data on normal forebody blowing and analytical studies of tangential blowing over conical forebodies. Incorporation of forebody blowing into the flight control system was investigated by adding this additional yaw control and sideforce generating actuator into the existing F-18 HARV simulation model. A control law was synthesized using LQG design methods that would schedule blowing rates as a function of vehicle sideslip, angle of attack, and roll and yaw rates.

Kroo, I.↗
NASA NTRS1991

Reusable Reentry Satellite (RRS) system design study. Phase B, appendix E: Attitude control system study

A study which consisted of a series of design analyses for an Attitude Control System (ACS) to be incorporated into the Re-usable Re-entry Satellite (RRS) was performed. The main thrust of the study was associated with defining the control laws and estimating the mass and power requirements of the ACS needed to meet the specified performance goals. The analyses concentrated on the different on-orbit control modes which start immediately after the separation of the RRS from the launch vehicle. The three distinct on-orbit modes considered for these analyses are as follows: (1) Mode 1 - A Gravity Gradient (GG) three-axis stabilized spacecraft with active magnetic control; (2) Mode 2 - A GG stabilized mode with a controlled yaw rotation rate ('rotisserie') using three-axis magnetic control and also incorporating a 10 N-m-s momentum wheel along the (Z) yaw axis; and (3) Mode 3 - A spin stabilized mode of operation with the spin about the pitch (Y) axis, incorporating a 20 N-m-s momentum wheel along the pitch (Y) axis and attitude control via thrusters. To investigate the capabilities of the different controllers in these various operational modes, a series of computer simulations and trade-off analyses have been made to evaluate the achievable performance levels, and the necessary mass and power requirements.

Source record↗
NASA NTRS1992

Forebody flow control on a full-scale F/A-18 aircraft

A full-scale F/A-18 was tested in the 80- by 120-Foot Wind Tunnel at NASA Ames Research Center to measure the effectiveness of pneumatic forebody vortex control devices. By altering the forebody vortex flow, yaw control can be maintained to angles of attack greater than 50 deg. Two forebody vortex control devices were tested: a discrete circular jet and a tangential slot. The tests were conducted for angles of attack between 25 and 50 deg, and angles of sideslip from 0 to +/- 15 deg. The Reynolds number based on wing mean aerodynamic chord ranged from 4.5 x 10 exp 6 to 12.0 x 10 exp 6. The time-averaged side forces and yawing moments, along with both time-averaged and time-dependent pressures on the forebody of the aircraft are presented here for various configurations. Of particular interest was the results that the tangential slot blowing had a greater effect on the yawing moment than the discrete circular jet. Additionally, it was found that blowing very close to the radome apex was not as effective as blowing slightly farther aft on the radome, and that a 16-inch slot was more effective than either an 8- or 48-inch long slot.

Lanser, Wendy R.↗
NASA NTRS1982

Microprocessor control system for 200-kilowatt Mod-OA wind turbines

The microprocessor system and program used to control the operation of the 200-kW Mod-OA wind turbines is described. The system is programmed to begin startup and shutdown sequences automatically and to control yaw motion. Rotor speed and power output are controlled with integral and proportional control of the blade pitch angle. Included in the report are a description of the hardware and a discussion of the software programming technique. A listing of the PL/M software program is given.

Nyland, T. W.↗
NASA NTRS1994

Preparations for flight research to evaluate actuated forebody strakes on the F-18 high-alpha research vehicle

As part of the NASA High-Angle-of-Attack Technology Program (HATP), flight tests are currently being conducted with a multi-axis thrust vectoring system applied to the NASA F-18 High Alpha Research Vehicle (HARV). A follow-on series of flight tests with the NASA F-18 HARV will be focusing on the application of actuated forebody strake controls. These controls are designed to provide increased levels of yaw control at high angles of attack where conventional aerodynamic controls become ineffective. The series of flight tests are collectively referred to as the Actuated Nose Strakes for Enhanced Rolling (ANSER) Flight Experiment. The development of actuated forebody strake controls for the F-18 HARV is discussed and a summary of the ground tests conducted in support of the flight experiment is provided. A summary of the preparations for the flight tests is also provided.

Murri, Daniel G.↗
NASA NTRS1990

Development of non-conventional control methods for high angle of attack flight using vortex manipulation

Methods of manipulating the forebody vortices on a generic fighter model to produce controlled yawing moments at high angles of attack were investigated. Forces and moments were measured on the complete configuration and on the isolated forebody. Two schemes for vortex control on the forebody were evaluated: individually-controlled tip strakes and individually-controlled blowing ports. The effectiveness of the forebody strakes in controlling forebody side forces was strongly dependent on the size and location of the strakes. A yawing moment can be produced by deploying the forebody strakes asymmetrically, or can be eliminated by deploying the strakes symmetrically. The most effective strake position was found to be near the primary separation point, between 105 and 120 deg from windward. Blowing on the surface of the model was also shown to have a strong effect on the yawing moment. Blowing either forward or aft tangential to the surface appears to be more effective than blowing normal to the surface. The most effective method to control the yawing moment on the forebody was to minimize the natural asymmetry with a pair of small symmetrically mounted tip strakes and to perturb the vortex system away from the symmetric condition with asymmetric blowing.

Malcolm, Gerald N.↗
NASA NTRS1990

Pneumatic vortical flow control at high angles of attack

The injection of thin, high-momentum jets of air into the fuselage forebody boundary layers of the F-18 aircraft is explored numerically as a means of controlling the onset of fuselage vortices and of generating yaw control forces. The study was carried out for an angle of attack of 30 deg with symmetrical and asymmetrical blowing configurations. One-sided blowing results in a strongly asymmetrical flow pattern in the fore portion of the fuselage, leading to a net lateral force.

Tavella, Domingo A.↗
NASA NTRS1988

Attitude analysis of the Earth Radiation Budget Satellite (ERBS) yaw turn anomaly

The July 2 Earth Radiation Budget Satellite (ERBS) hydrazine thruster-controlled yaw inversion maneuver resulted in a 2.1 deg/sec attitude spin. This mode continued for 150 minutes until the spacecraft was inertially despun using the hydrazine thrusters. The spacecraft remained in a low-rate Y-axis spin of .06 deg/sec for 3 hours until the B-DOT control mode was activated. After 5 hours in this mode, the spacecraft Y-axis was aligned to the orbit normal, and the spacecraft was commanded to the mission mode of attitude control. This work presents the experience of real-time attitude determination support following analysis using the playback telemetry tape recorded for 7 hours from the start of the attitude control anomaly.

Kronenwetter, J.↗
NASA NTRS1990

Forebody vortex control as a complement to thrust vectoring

The desire to enhance the controllability of fighter aircraft at high angles of attack, particularly yaw control, has fostered an interest in both vectored thrust and active control of forebody vortices. This paper reviews several methods of forebody vortex control that have been investigated with water and wind tunnel tests of both generic and actual fighter configurations. The methods investigated include pneumatic or blowing techniques using surface-mounted jets and slots, surface suction, variable-height deployable strakes, and rotatable tip strakes. Flow visualization, and force and moment measurements have shown that all of the methods are effective in manipulating the forebody vortices over a wide range of angles of attack and sideslip, primarily through control over flow separation on the surface of the forebody. All are most effective when applied near the forebody tip. The advantages and limitations of the various methods are reviewed.

Malcolm, G. N.↗
NASA NTRS1992

The ACTS Spacecraft

The tested physical and performance characteristics of the ACTS spacecraft are presented with emphasis placed on those for the multibeam antenna, the communications electronics panel, and the bus. Performance measurements for the multibeam antenna agree with predicted parameters, and the electronics panel provides four transponder channels for redundancy and system reliability. The spacecraft bus provides unique features including an attitude-control subsystem with autotrack for pitch accuracy, a sun sensor for yaw control, and thruster firing for dual spin turns.

Gargione, Frank↗