Results for “weight loss” — Page 4

NASA NTRS1988

700 F properties of autoclave cured PMR-II composites

Studies were conducted to develop autoclave processing parameters for graphite reinforced PMR-2 resin composite materials intended for use in applications at temperatures up to 371 degrees (700 F). The effect of resin composition on autoclaveability was investigated. The effect of various graphite fibers and resin composition on 343 C (650 F) and 371 C (700 F) thermo-oxidative stability and mechanical properties was also investigated. The results of the processing studies show that PMR-2 resin composites can be easily fabricated under autoclave conditions. Autoclaved laminates exposed to 1 atm of air at 343 C (650 F) and 371 C (700 F) exhibited less than 5 percent weight loss after 750 hr exposure to 650 F air and 8 percent weight loss during exposure to 700 F air for 500 hr. After 500 hr exposure, autoclaved laminates exhibited greater than 90 percent retention of initial 650 and 700 F flexural and interlaminar shear strengths. The effect of resin formulated molecular weight and postcure conditions on laminate glass transition temperature is also discussed.

Cifani, Diane↗

NASA NTRS1992

Heat stress and a countermeasure in the Shuttle rescueman's suit

Rescue of the astronaut flight crew from a contingency landing may risk exposure of the rescue crew to toxic propellants spilling from potentially ruptured tanks in the crew module area. An Aquala dry diver's suit has been in service by the rescue team to preclude exposure, especially in the water rescue scenario. Heat stress has become a factor of concern in recent years when older and less physically-fit team members work in this suit. Methods: Field testing was initiated using fully instrumented rescue men in a simulated scenario to determine the extent of heat stress. Two tests were accomplished, one in the normal (N) configuration and one with a proposed cooling countermeasure, the Steele vest (S). Results: Heat stress was high as indicated by average rectal temperatures (Tre) of 38.28 degrees C(100.9 degrees F) after the 45 minute protocol. Slopes of the regression equations describing the increase in Tre with time were greater (P less than 0.05) with N (0.073 plus or minus .008) compared to S (0.060 plus or minus .007). Projection of time to the 38.89 degree C (102 degree F) limit was increased by 15.3 percent with the vest. Mean skin temperature (Tsk) was higher (P less than 0.05) in N (38.33 plus or minus .11 degrees C) compared to S (34.33 plus or minus .39 degrees C). Average heart rate was higher (P less than 0.05 in N than S. Sweat loss, as measured by weight loss, was more (P less than 0.05) for N (1.09 plus or minus .09 kg versus 0.77 plus or minus .06 kg). Air usage, while slightly less for S, was not statistically different. Conclusion: The use of the cool vest provided significant relief from thermal stress in spite of the addition of 3.4 kg (7.5 pounds) weight and some loss in mobility.

Doerr, D. F.↗

DOE OSTI2024

CT584 Is Not a Protective Vaccine Antigen against Respiratory Chlamydial Challenge in Mice

Background: Chlamydia trachomatis is the most prevalent bacterial sexually transmitted pathogen in humans worldwide. Since chlamydial infection is largely asymptomatic with the potential for serious complications, a preventative vaccine is likely the most viable long-term answer to this public health threat. Cell-free protein synthesis (CFPS) utilizes the cellular protein manufacturing machinery decoupled from the requirement for maintaining cellular viability, offering the potential for flexible, rapid, and decentralized production of recombinant protein vaccine antigens. Methods: Here, we use CFPS to produce the full-length putative chlamydial type three secretion system (T3SS) needle-tip protein, CT584, for evaluation as a vaccine antigen in mouse models. High-speed atomic force microscopy (HS-AFM) (RIBM, Tsukuba, Japan) imaging and computer simulations confirm that CFPS-produced CT584 retains a native-like structure prior to immunization. Female mice were primed with CT584 adjuvanted with CpG-1826 intranasally (i.n.) or CpG-1826 + Montanide ISA 720 intramuscularly (i.m.), followed four weeks later by an i.m. boost before respiratory challenge with 10 4 inclusion forming units (IFU) of Chlamydia muridarum. Results: Immunization with CT584 generated robust antibody responses but weak cell-mediated immunity and failed to protect against i.n. challenge as demonstrated by body weight loss, increased lung weights, and the presence of high numbers of IFUs in the lungs. Conclusion: While CT584 was not a protective vaccine candidate, the speed and flexibility with which CFPS can be used to produce other potential chlamydial antigens make it an attractive technique for antigen production.

60 APPLIED LIFE SCIENCES↗

NASA NTRS1973

Estimates of fluid and energy balances of Apollo 17

Fluid and caloric balance has been calculated for the Apollo 17 crew. This included measurement of nitrogen, water, and caloric value of the ingested food and the volume and nitrogen content of the excreted urine and feces. Body composition changes were determined from total body water and extracellular fluid volume differences. The body composition measurements made it possible to divide the weight loss into lean body mass and adipose tissue losses. From this division a caloric equivalent was calculated. These tissue losses indicated that the caloric requirements of the mission were considerably greater than the actual caloric intake. The 3.3 kilo mean loss of body weight represented 1 kilo of lean body mass and 2.3 kilos of adipose tissue. Calculated fluid balance was more positive during the mission than during the control period. These changes are unlike the body composition and fluid balance changes reported in bedrested subjects.

Johnson, P. C.↗

NASA NTRS1981

The effects of space flight on some rat liver enzymes regulating carbohydrate and lipid metabolism

The effects of space flight conditions on the activities of certain enzymes regulating carbohydrate and lipid metabolism in rat liver are investigated in an attempt to account for the losses in body weight observed during space flight despite preflight caloric consumption. Liver samples were analyzed for the activities of 32 cytosolic and microsomal enzymes as well as hepatic glycogen and individual fatty acid levels for ground control rats and rats flown on board the Cosmos 936 biosatellite under normal space flight conditions and in centrifuges which were sacrificed upon recovery or 25 days after recovery. Significant decreases in the activities of glycogen phosphorylase, alpha-glycerol phosphate acyl transferase, diglyceride acyl transferase, aconitase and 6-phosphogluconate dehydrogenase and an increase in palmitoyl CoA desaturase are found in the flight stationary relative to the flight contrifuged rats upon recovery, with all enzymes showing alterations returning to normal values 25 days postflight. The flight stationary group is also observed to be characterized by more than twice the amount of liver glycogen of the flight centrifuged group as well as a significant increase in the ratio of palmitic to palmitoleic acid. Results thus indicate metabolic changes which may be involved in the mechanism of weight loss during weightlessness, and demonstrate the equivalence of centrifugation during space flight to terrestrial gravity.

Abraham, S.↗

NASA NTRS1994

Oxidation Protection of Porous Reaction-Bonded Silicon Nitride

Oxidation kinetics of both as-fabricated and coated reaction-bonded silicon nitride (RBSN) were studied at 900 and 1000 C with thermogravimetry. Uncoated RBSN exhibited internal oxidation and parabolic kinetics. An amorphous Si-C-O coating provided the greatest degree of protection to oxygen, with a small linear weight loss observed. Linear weight gains were measured on samples with an amorphous Si-N-C coating. Chemically vapor deposited (CVD) Si3N4 coated RBSN exhibited parabolic kinetics, and the coating cracked severely. A continuous-SiC-fiber-reinforced RBSN composite was also coated with the Si-C-O material, but no substantial oxidation protection was observed.

Fox, D. S.↗

NASA NTRS1997

The effects of programmed administration of human parathyroid hormone fragment (1-34) on bone histomorphometry and serum chemistry in rats

PTH treatment can result in dramatic increases in cancellous bone volume in normal and osteopenic rats. However, this potentially beneficial response is only observed after pulsatile treatment; continuous infusion of PTH leads to hypercalcemia and bone abnormalities. The purpose of these studies was to determine the optimal duration of the PTH pulses. A preliminary study revealed that human PTH-(1-34) (hPTH) is cleared from circulation within 6 h after sc administration of an anabolic dose of the hormone (80 microg/kg). To establish the effects of gradually extending the duration of exposure to hPTH without increasing the daily dose, we programmed implanted Alzet osmotic pumps to deliver the 80 microg/kg x day dose of the hormone during pulses of 1, 2, and 6 h/day, or 40 microg/kg x day continuously. Discontinuous infusion was accomplished by alternate spacing of external tubing with hPTH solution and sesame oil. After 6 days of treatment, we evaluated serum chemistry and bone histomorphometry. As negative and positive controls, groups of rats received pumps that delivered vehicle only and 80 microg/kg x day hPTH by daily sc injection, respectively. Dynamic and static bone histomorphometry revealed that the daily sc injection and 1 h/day infusion dramatically increased osteoblast number and bone formation in the proximal tibial metaphysis, whereas longer infusion resulted in systemic side-effects, including up to a 10% loss in body weight, hypercalcemia, and histological changes in the proximal tibia resembling abnormalities observed in patients with chronic primary hyperparathyroidism, including peritrabecular marrow fibrosis and focal bone resorption. Infusion for as little as 2 h/day resulted in minor weight loss and changes in bone histology that were intermediate between sc and continuous administration. The results demonstrate that the therapeutic interval for hPTH exposure is brief, but that programmed administration of implanted hormone is a feasible alternative to daily injection as a route for administration of the hormone.

Non-NASA Center↗

DOE OSTI2024

Tuning Microstructure of Mesophase Pitch Carbon Fiber by Altering the Carbonization Ramp Rate

The microstructure of mesophase pitch carbon fibers (CFs) are tuned by varying ramp rates from 1 to 50 °C min –1 up to 1000 °C to study the effect of ramp rate on CFs’ microstructure, thermal and mechanical properties with the goal of offsetting the cost by decreasing cycle time. The ramp rates represent carbonization times ranging from 16.4 to 1.17 h, not including cool down. Differential scanning calorimetry, thermogravimetric analysis, and derivative thermogravimetry are used to investigate the impact ramp rate has on the thermal properties of mesophase pitch. It is found that lower ramp rates are endothermic in nature with a lower temperature onset and maximum weight loss. Higher ramp rates possess an exothermic nature with higher temperatures resulting in maximal weight loss over a smaller range of temperatures. Mechanical testing shows varying CF strengths and moduli dependent on ramp rate and an optimized process is developed to produce the strongest CF. Furthermore, microstructural characterization revealed that faster ramp rates lead to smaller interplanar spacings and larger crystallites but possessed greater disorder.

36 MATERIALS SCIENCE↗

NASA NTRSDate not supplied

Appetite and Food Intake During 11 Days of Mild Hypobaric Hypoxia

Introduction Reduced food consumption and loss of body mass and muscle mass have been observed during spaceflight. Hypoxic conditions that astronauts may encounter on exploration missions may further implicate satiety signals and dietary intake. Appetite, food intake, and satiety hormones were investigated under the conditions of mild hypoxia and high energy output during simulated extravehicular activity (EVA) to determine the adequacy of a mission relevant space food system to support energy balance and body composition. Methods Foods realistic to early Artemis missions was packed by meal for each subject for the 11-day test based on estimated energy requirements (EER) and estimated EVA caloric requirements. No hot water or food warmer was provided and only room temperature water was available to rehydrate food and beverages in-mission, mimicking plans for early Artemis missions. Measures included food records (pre-mission, in-mission); fasted body weight (pre-mission, in-mission); Dual-energy X-ray absorptiometry (DXA) (pre-mission, post-mission); subjective ratings and feedback of food acceptability, mealtime and meal preparation sufficiency, appetite, and nausea (in-mission); and circulating ghrelin and leptin concentration in fasted blood samples (pre-mission, in-mission: pre-post EVA). Results All subjects consumed fewer calories in-mission than predicted. On average, subjects consumed 341 calories less on EVA days compared to non-EVA days in-mission (p=0.0511). The total weight loss estimate from daily weight measurements (-1.1 kg, p=0.0028) is consistent with underconsumption and supported by DXA measurements (-1.3 kg total body mass, p=0.0123 and -1.6 kg fat mass, p=0.0016). In general, most foods that were consumed were given acceptable scores, but subject comments indicated that the most acceptable foods were those not intended to be heated. Comments also indicated that subjects found their favorite foods early in the mission and avoided the foods that they did not like throughout the mission. Habitability scores indicated that overall aspects of the food system were considered borderline or unacceptable over the length of this mission. Foods that caused gas were avoided pre-EVA to prevent discomfort during pressure changes. Average fruit and vegetable intake decreased during the mission, dropping from 4.8 servings/d pre-mission to 3.4 servings/d on non-EVA days in-mission (p=0.0872) and 2.3 servings on EVA days (p=0.0020). Fasting ghrelin concentrations tended to be lower pre-EVA and on non-EVA days when exposed to mild hypoxia compared to normoxic conditions pre-mission and post-EVA (p=0.0136). Fasting levels of leptin did not change. Discussion Food intake was reduced in-mission, resulting in a caloric deficit and weight loss for most subjects. Crew food and appetite ratings and comments indicated this was due to a combination of food choices, lack of preference, lack of preparation capability, lack of time for meal preparation, consumption, and cleanup, and physiological challenges with the changing pressure. The regulation of appetite stimulating hormone ghrelin, but not the appetite suppressor leptin, appeared to be sensitive to hypoxic conditions. Conclusions Food preparation capabilities and time for meals are important for promoting adequate food intake. Reduced appetite and food intake during missions may further be aggravated under hypoxic conditions through the suppression of ghrelin. Lack of time for meals on EVA days, and avoidance of potential gas-causing foods (e.g., health promoting fruits and vegetables) prior to EVAs, demonstrate the importance of scheduling ample recovery time between EVA days.

Grace L Douglas↗

NASA NTRS2023

Appetite and Food Intake During 11 Days of Mild Hypobaric Hypoxia

Introduction Reduced food consumption and loss of body mass and muscle mass have been observed during spaceflight. Hypoxic conditions that astronauts may encounter on exploration missions may further implicate satiety signals and dietary intake. Appetite, food intake, and satiety hormones were investigated under the conditions of mild hypoxia and high energy output during simulated extravehicular activity (EVA) to determine the adequacy of a mission relevant space food system to support energy balance and body composition. Methods Foods realistic to early Artemis missions was packed by meal for each subject for the 11-day test based on estimated energy requirements (EER) and estimated EVA caloric requirements. No hot water or food warmer was provided and only room temperature water was available to rehydrate food and beverages in-mission, mimicking plans for early Artemis missions. Measures included food records (pre-mission, in-mission); fasted body weight (pre-mission, in-mission); Dual-energy X-ray absorptiometry (DXA) (pre-mission, post-mission); subjective ratings and feedback of food acceptability, mealtime and meal preparation sufficiency, appetite, and nausea (in-mission); and circulating ghrelin and leptin concentration in fasted blood samples (pre-mission, in-mission: pre-post EVA). Results All subjects consumed fewer calories in-mission than predicted. On average, subjects consumed 341 calories less on EVA days compared to non-EVA days in-mission (p=0.0511). The total weight loss estimate from daily weight measurements (-1.1 kg, p=0.0028) is consistent with underconsumption and supported by DXA measurements (-1.3 kg total body mass, p=0.0123 and -1.6 kg fat mass, p=0.0016). In general, most foods that were consumed were given acceptable scores, but subject comments indicated that the most acceptable foods were those not intended to be heated. Comments also indicated that subjects found their favorite foods early in the mission and avoided the foods that they did not like throughout the mission. Habitability scores indicated that overall aspects of the food system were considered borderline or unacceptable over the length of this mission. Foods that caused gas were avoided pre-EVA to prevent discomfort during pressure changes. Average fruit and vegetable intake decreased during the mission, dropping from 4.8 servings/d pre-mission to 3.4 servings/d on non-EVA days in-mission (p=0.0872) and 2.3 servings on EVA days (p=0.0020). Fasting ghrelin concentrations tended to be lower pre-EVA and on non-EVA days when exposed to mild hypoxia compared to normoxic conditions pre-mission and post-EVA (p=0.0136). Fasting levels of leptin did not change. Discussion Food intake was reduced in-mission, resulting in a caloric deficit and weight loss for most subjects. Crew food and appetite ratings and comments indicated this was due to a combination of food choices, lack of preference, lack of preparation capability, lack of time for meal preparation, consumption, and cleanup, and physiological challenges with the changing pressure. The regulation of appetite stimulating hormone ghrelin, but not the appetite suppressor leptin, appeared to be sensitive to hypoxic conditions. Conclusions Food preparation capabilities and time for meals are important for promoting adequate food intake. Reduced appetite and food intake during missions may further be aggravated under hypoxic conditions through the suppression of ghrelin. Lack of time for meals on EVA days, and avoidance of potential gas-causing foods (e.g., health promoting fruits and vegetables) prior to EVAs, demonstrate the importance of scheduling ample recovery time between EVA days.

Lichar Dillon↗

NASA NTRS1976

Fiber composite fan blade impact improvement

The improved foreign object damage resistance of a metal matrix advanced composite fan blade was demonstrated. The fabrication, whirl impact test and subsequent evaluation of nine advanced composite fan blades of the "QCSEE" type design were performed. The blades were designed to operate at a tip speed of 282 m/sec. The blade design was the spar/shell type, consisting of a titanium spar and boron/aluminum composite airfoils. The blade retention was designed to rock on impact with large birds, thereby reducing the blade bending stresses. The program demonstrated the ability of the blades to sustain impacts with up to 681 g slices of birds at 0.38 rad with little damage (only 1.4 percent max weight loss) and 788 g slices of birds at 0.56 rad with only 3.2 percent max weight loss. Unbonding did not exceed 1.1 percent of the post-test blade area during any of the tests. All blades in the post-test condition were judged capable of operation in accordance with the FAA guidelines for medium and large bird impacts.

Graff, J.↗

NASA NTRS1974

Continuation of development of nitrides for space nuclear reactors

Alloy nitrides (U,Zr), (U,Ce), and (U,Y) were prepared and exposed to vacuum at temperatures to 1700 C (1973 K) and compared with pure UN. Weight loss data and physical observations showed that the alloy samples were more stable than UN. In weight loss, (U,Zr)N was 3 times as stable as UN at 1600 C (1873 K) for 100 hr at 0.000002 torr (0.000266n/sq.m.).

Potter, R. A.↗

NASA NTRS1989

Effect of low air velocities on thermal homeostasis and comfort during exercise at space station operational temperature and humidity

The effectiveness of different low air velocities in maintaining thermal comfort and homeostasis during exercise at space station operational temperature and humidity was investigated. Five male subjects exercised on a treadmill for successive ten minute periods at 60, 71, and 83 percent of maximum oxygen consumption at each of four air velocities, 30, 50, 80, and 120 ft/min, at 22 C and 62 percent relative humidity. No consistent trends or statistically significant differences between air velocities were found in body weight loss, sweat accumulation, or changes in rectal, skin, and body temperatures. Occurrence of the smallest body weight loss at 120 ft/min, the largest sweat accumulation at 30 ft/min, and the smallest rise in rectal temperature and the greatest drop in skin temperature at 120 ft/min all suggested more efficient evaporative cooling at the highest velocity. Heat storage at all velocities was evidenced by increased rectal and body temperatures; skin temperatures declined or increased only slightly. Body and rectal temperature increases corresponded with increased perception of warmth and slight thermal discomfort as exercise progressed. At all air velocities, mean thermal perception never exceeded warm and mean discomfort, greatest at 30 ft/min, was categorized at worst as uncomfortable; sensation of thermal neutrality and comfort returned rapidly after cessation of exercise. Suggestions for further elucidation of the effects of low air velocities on thermal comfort and homeostasis include larger numbers of subjects, more extensive skin temperature measurements and more rigorous analysis of the data from this study.

Beumer, Ronald J.↗

NASA NTRS1997

Oxidative Degradation of Nadic-End-Capped Polyimides: Evidence for Reactions Occurring at High Temperatures - 2

The oxidative degradation of PMR (for polymerization of monomeric reactants) polyimides at elevated temperatures was followed by cross-polarized magic angle spinning (Cp-MAS) NMR. C-13 labeling of selected sites in the polymers allowed for direct observation of the transformations arising from oxidation processes. As opposed to model compound studies, the reactions were followed directly in the polymer. The labeling experiments confirm the previously reported oxidation of the methylene carbon to ketone in the methylenedianiline portion of the polymer chain. They also show the formation of two other oxidized species, acid and ester, from this same carbon. In addition, the technique provides the first evidence of the kind of degradation reactions that are occurring in the nadic end caps. Several PMR formulations containing moieties determined to be present after oxidation, as suggested by the labeling study, were synthesized. Weight loss, FTIR, and natural abundance NMR of these derivatives were followed during aging. In this way, weight loss could be related to the observed transformations.

Meador, Mary Ann B.↗

NASA NTRS1983

Quantitation of tissue loss during prolonged space flight

An analysis of data from the three Skylab missions was performed to assess the lean body mass (LBM) and fat components of inflight body weight loss. Six methods for determining LBM were employed based on changes in total body water, total body potassium, nitrogen balance, potassium balance, and stereophotometric-body density. Those based solely on body potassium, and potassium and nitrogen balances (when expressed as shifts from preflight control), consistently overestimated LBM loss unless appropriate corrections were made. The average results from the various methods indicated that of a mean inflight total body weight loss of 2.7 + or - 0.3 kg (SD) for all nine crewmembers, more than half (1.5 + or - 0.3 kg) can be attributed to loss of LBM (including 1.1 kg body water), the remainder (1.2 + or - 0.3 kg) being derived from fat stores. The reduction of LBM appeared to be complete after the first month of flight and thereafter was largely independent of mission duration, diet, and exercise.

Leonard, J. I.↗

NASA NTRS2005

High Temperature Thermosetting Polyimide Nanocomposites Prepared with Reduced Charge Organoclay

The naturally occurring sodium and calcium cations found in bentonite clay galleries were exchanged with lithium cations. Following the cation exchange, a series of reduced charge clays were prepared by heat treatment of the lithium bentonite at 130 C, 150 C, or 170 C. Inductively coupled plasma (ICP) analysis showed that heating the lithium clay at elevated temperatures reduced its cation exchange capacity. Ion exchange of heat-treated clays with either a protonated alkyl amine or a protonated aromatic diamine resulted in decreasing amounts of the organic modifier incorporated into the lithium clay. The level of silicate dispersion in a thermosetting polyimide matrix was dependent upon the temperature of Li-clay heat treatment as well as the organic modification. In general, clays treated at 150 C or 170 C, and exchanged with protonated octadcylamine or protonated 2,2'-dimethlybenzidine (DMBZ) showed a higher degree of dispersion than clays treated at 130 C, or exchanged with protonated dodecylamine. Dynamic mechanical analysis showed little change in the storage modulus or T(sub g) of the nanocomposites compared to the base resin. However, long term isothermal aging of the samples showed a significant decrease in the resin oxidative weight loss. Nanocomposite samples aged in air for 1000 hours at 288 C showed of to a decrease in weight loss compared to that of the base resin. This again was dependent on the temperature at which the Li-clay was heated and the choice of organic modification.

Campbell, Sandi↗

NASA NTRS2006

Cyclic Oxidation Behavior of Cold Sprayed CuCrAl-Coated and Uncoated GRCop-84 Substrates for Space Launch Vehicles

A newly developed Cu-23 (wt %) Cr-5%Al (CuCrAl) alloy shown to resist hydridation and oxidation in an as-cast form is currently being considered as a protective coating for GRCop-84, which is an advanced copper alloy containing 8 (at.%) Cr and 4 (at.%) Nb. The coating was deposited on GRCop-84 substrates by the cold spray deposition technique. Cyclic oxidation tests conducted in air on both coated and uncoated substrates between 773 and 1073 K revealed that the coating remained intact and protected the substrate up to 1073 K. No significant weight loss of the coated specimens were observed at 773 and 873 K even after a cumulative cyclic time of 500 h. About a 10 percent weight loss observed at 973 and 1073 K was attributed to the excessive oxidation of the uncoated sides. In contrast, the uncoated substrate lost as much as 80 percent of its original weight under similar test conditions. It is concluded that the cold sprayed CuCrAl coating is suitable for protecting GRCop-84 substrates.

Raj, S. V.↗

NASA NTRS2002

COSP for Windows: Strategies for Rapid Analyses of Cyclic Oxidation Behavior

COSP is a publicly available computer program that models the cyclic oxidation weight gain and spallation process. Inputs to the model include the selection of an oxidation growth law and a spalling geometry, plus oxide phase, growth rate, spall constant, and cycle duration parameters. Output includes weight change, the amounts of retained and spalled oxide, the total oxygen and metal consumed, and the terminal rates of weight loss and metal consumption. The present version is Windows based and can accordingly be operated conveniently while other applications remain open for importing experimental weight change data, storing model output data, or plotting model curves. Point-and-click operating features include multiple drop-down menus for input parameters, data importing, and quick, on-screen plots showing one selection of the six output parameters for up to 10 models. A run summary text lists various characteristic parameters that are helpful in describing cyclic behavior, such as the maximum weight change, the number of cycles to reach the maximum weight gain or zero weight change, the ratio of these, and the final rate of weight loss. The program includes save and print options as well as a help file. Families of model curves readily show the sensitivity to various input parameters. The cyclic behaviors of nickel aluminide (NiAl) and a complex superalloy are shown to be properly fitted by model curves. However, caution is always advised regarding the uniqueness claimed for any specific set of input parameters,

Smialek, James L.↗