Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “voltammetry”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Oxygen‐Assisted Supercapacitive Swing Adsorption of Carbon Dioxide

Abstract We report on the supercapacitive swing adsorption (SSA) of carbon dioxide at different voltage windows in the presence of oxygen using activated carbon electrodes, and deliquescent, aqueous electrolytes. The presence of O 2 in the CO 2 /N 2 gas mixture results in an up to 11 times higher CO 2 adsorption capacity with 3 M MgBr 2 (at 0.6 V) and up to 4–5 times higher adsorption capacity with 3 M MgCl 2 (at 1 V). A tradeoff between high CO 2 adsorption capacities and lower coulombic efficiencies was observed at voltages above 0.6 V. The energetic and adsorptive performance of the electrodes in the presence of oxygen below 0.5 V was similar to the performance with a CO 2 /N 2 mixture without oxygen at 1 V. Cyclic voltammetry (CV) and electrochemical impedance spectroscopy (EIS) of the electrodes demonstrate that the specific capacitance increases while the diffusion resistance decreases in the presence of oxygen. Oxygen concentrations ranging between 5–20 % give similar energetic and adsorptive performance. The electrodes exhibit stable performance for up to 100 cycles of operation.

Bilal, Muhammad↗
DOE OSTI2026

Electron-Deficient Phenazines: Synthesis, Structures, Redox, and Optoelectronic Properties in the Gas Phase, in Solution, and in the Solid State

High-temperature gas-phase reactions of 1,4-C4F8I2 with phenazine (PHNZ) afforded new thermally- and air-stable derivatives with cyclo-C4F8 substituents, viz. 1,2-PHNZ(C4F8), 2,3-PHNZ(C4F8), 1,2:6,7-PHNZ(C4F8)2, 1,2:7,8-PHNZ(C4F8)2, and 1,2:8,9-PHNZ(C4F8)2. Reactions in the presence of Cu powder resulted in reductive-defluorination/aromatization of some of the cyclo-C4F8 substituents to produce 2,3-PHNZ(C4F4), 2,3-PHNZ(C4HF3), and 1,2:6,7-PHNZ(C4F8)(C4F4), which are formally tri- or tetrafluoro derivatives of benzo[a]phenazine. Single-crystal X-ray diffraction structures of these compounds demonstrate the planarity of 2,3-PHNZ(C4F4) and 2,3-PHNZ(C4HF3) and ordered p-stacking in 1,2-PHNZ(C4HF3), 1,2-PHNZ(C4F4), 1,2-PHNZ(C4F8), and 2,3-PHNZ(C4F8). Low-temperature gas-phase photoelectron spectra of the PHNZ(C4F8)1,2 compounds show that they are strong electron acceptors, with the three PHNZ(C4F8)2 isomers having electron affinities exceeding that of C60. Cyclic voltammetry in acetonitrile show that the five PHNZ(C4F8)1,2 compounds exhibit reversible one-electron reductions with large positive shifts in their reduction potentials relative to unsubstituted PHNZ. Spectroelectrochemical absorption and EPR spectra of PHNZ(C4F8)1,2- • anion radicals and extensive DFT calculations revealed the significant role that the different substitution patterns have on determining the optoelectronic properties of the PHNZ(C4F8)1,2 derivatives and PHNZ(C4F8)1,2- • anion radicals. Time-resolved microwave conductivity measurements and photoluminescence spectra of blends of the PHNZ(C4F8)1,2 derivatives with the donor poly(3-hexylthiophene) (P3HT) were recorded to assess the possible use of the new compounds in optoelectronic devices.

Balser, Sebastian↗
DOE OSTI2023

Polycarbonate‐Based Solid‐Polymer Electrolytes for Solid‐State Sodium Batteries

Solid-polymer electrolytes comprised of polypropylene carbonate (PPC) and varied sodium bis(fluorosulfonyl)imide (NaFSI) salt concentrations are investigated for implementation as a conductive solid polymer electrolyte into solid-state cathode composites utilizing a sodium-layered oxide active material. The ionic conductivity generally increases with NaFSI salt content, reaching ≈1 mS cm −1 at 80 °C at the highest salt concentration (PPC:NaFSI = 0.5:1). Through an all-in-one slurry casting method, Na 2/3 Ni 1/3 Mn 2/3 O 2 cathode composites are fabricated in which the dispersed PPC electrolyte acts as the primary binder. Enabled by a bilayer polymer electrolyte system, cycling performance with the PPC cathode electrolyte is optimized with respect to salt concentration and anode material. The best cyclability is achieved with a moderate salt concentration electrolyte (PPC:NaFSI = 5:1), showcasing an initial capacity of 83 mA h g −1 with a remarkable 80% capacity retention after 150 cycles at C/5 rate and 60 °C. The superior performance of the lower salt concentration electrolyte is attributed to better electrochemical stability, as confirmed by linear sweep voltammetry and online electrochemical mass spectrometry measurements. In conclusion, these results underscore the potential of carbonate-based polymer electrolytes and the importance of balancing electrolyte conductivity and stability in cell design.

25 ENERGY STORAGE↗
DOE OSTI2024

Single-atom materials boosting wearable orthogonal uric acid detection

Abstract Uric acid (UA) is a vital biomarker for the diagnosis and management of various health conditions, including cardiovascular diseases, gout, kidney disorders, metabolic syndrome, and wound healing. Despite significant advances in wearable sensor technology, challenges persist in developing wearable sensors that are capable of maintaining high sensitivity, selectivity, and stability. In this study, we present an epidermal sensing platform enhanced with single-atom materials (SAMs) designed for flexible and orthogonal electrochemical detection of UA. We designed and synthesized an SAM with Fe-N 5 active sites to boost the electrochemical sensing signals, integrating it with laser-engraved graphene (LEG) to fabricate a wearable SAM-based UA patch sensor. This design provides superior UA detection performance compared to sensors based on conventional nanomaterials. In addition, we enhanced the detection accuracy and range by using an orthogonal approach that combines direct oxidation through differential pulse voltammetry (DPV) along with parallel biocatalytic amperometric detection. The resulting SAM-based UA orthogonal sensor patch demonstrated exceptional performance in wearable applications through tests measuring sweat UA levels in subjects before and after consuming a purine-rich diet. Graphical Abstract

Ding, Shichao↗
DOE OSTI2025

Electrocatalytic benchmarking of ruthenium-based bimetallic anodes for the electrocatalytic oxidation of biomass-derived wastewater

In this paper, we report on the synthesis, characterization, and use of ruthenium oxide (RuO 2 ) doped with a secondary metal (M2) to enhance electrochemical activity and stability for the electrocatalytic oxidation (ECO) of biomass-derived wastewaters. We used different electrochemical methods such as cyclic voltammetry (CV), electrochemical surface area (ECSA), and Tafel analysis as well as physical characterization such as grazing incidence X-ray diffraction, X-ray photoelectron spectroscopy, and scanning electron microscopy to understand how the introduction of M2 affects electrochemical performance. Our results show that including an M2 improves the ECO performance regardless of the composition of the electrolyte. Specifically, we saw increase in ECSA, which could be due to enhanced charge transfer for the pH ranges evaluated. Furthermore, the introduction of organic compounds in wastewater generated during the hydrothermal liquefaction of food waste affected the ECO performance differently, depending on M2, the electrolyte composition, and anodic half-cell potential, highlighting the need to properly control the reaction conditions when testing and characterizing the electrocatalysts under different reaction regimes. We developed an in situ electrocatalytic benchmarking protocol, Boruah – Lopez-Ruiz – Strange (BLoRS), to quickly assess if the presence of M2 improves the ECO performance; thus, saving time and resources in ex situ characterization, testing, and product analysis. This foundational work provides the basis for characterization and benchmarking of electrodes of the ECO of organic compounds.

Electrocatalysis↗
DOE OSTI2025

Efficient BiVO 4 /CoFeO x H y photoanodes using controlled annealing and conformal linear-sweep electrocatalyst photodeposition

Although monoclinic bismuth vanadate (BiVO 4 ) is a promising photoanode for solar water splitting, its practical use is hindered by imperfect photocurrent generation/collection, low photovoltage compared to the bandgap, and corrosion side reactions that limit durability. Here, we introduce a controlled-annealing sol–gel process for BiVO 4 thin-film photoanodes along with an optimized linear-sweep-voltammetry photodeposition of CoFeO x H y cocatalysts. The resulting BiVO 4 films annealed at 550 °C exhibited a photocurrent density of 4.1 mA/cm 2 at 1.23 V RHE under 1 sun AM 1.5G solar simulation and a low onset potential of 0.26 V RHE due to high majority carrier conductivity, a crystalline bulk with reduced defects as evidenced by x-ray photoelectron spectroscopy and photoluminescence lifetime analysis, and thus enhanced photocarrier collection. However, significant degradation in performance was found due to interfacial photocorrosion. To protect the surface and speed the oxygen-evolution reaction CoFeO x H y cocatalyst layers were deposited. By varying the number of consecutive sweeps and adjusting the applied bias range, an ultra-thin (~15 nm) CoFeO x H y cocatalyst layer was uniformly grown deposited over 30 cycles on the BiVO 4 surface. The resulting BiVO 4 /CoFeO x H y yielded 4.03 mA/cm 2 at 1.23 V RHE and onset potential of 0.24 V RHE , with stable operation (~15 % loss in photocurrent at 1.23 V RHE relative to ~60 % loss in the uncatalyzed control sample). These conformal CoFeO x H y catalytic layers function simultaneously to selectively collect photoexcited holes from the BiVO 4 , catalyze the water-oxidation reaction, and protect the BiVO 4 from photodegradation.

42 ENGINEERING↗
DOE OSTI2026

Nano zero valent iron electrodeposition at boron doped diamond electrodes

Here, in this study, we present an ecofriendly and simple electrochemical method for synthesizing nano zero-valent iron particles (nZVIs) directly on boron-doped diamond (BDD) electrode surfaces. A BDD electrode served as the substrate for electrodeposition using a 5 mM FeCl 3 /0.1 M KCl solution and chronoamperometry at an applied potential of −1.3 V versus Ag/AgCl (1 M KCl), as determined by cyclic voltammetry (CV) and supported by Pourbaix diagram analysis. The electrochemical behavior and surface modification were characterized using CV, electrochemical impedance spectroscopy (EIS), and surface analysis and microscopy techniques. The results confirm that BDD electrodes can serve as effective platforms for a controlled deposition of 56 nm nZVIs, offering a promising strategy for the development of advanced materials for environmental remediation, catalysis, and sensing applications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Electrochemical stability and corrosion behavior of Ni-Cr alloy in molten LiCl-KCl salt

This study investigated the electrochemical properties and potential-dependent stability of Cr(II) and Ni(II) in a eutectic LiCl-KCl molten salt at 500 °C under an argon atmosphere using a three-electrode cell configuration with a glassy carbon working electrode, Ag/Ag + reference electrode, and graphite counter electrode. Cyclic voltammetry was employed to characterize the Cr(0)/Cr(II)/Cr(III) and Ni(0)/Ni(II) redox transitions, yielding diffusion coefficients of 0.50 (±0.01) × 10 −5 cm 2 s −1 for Cr(II) and 0.91 (±0.16) × 10 −5 cm 2 s −1 for Ni(II) at 500 °C. The redox stability domains of these species provided insight into the corrosion mechanisms of a Ni-Cr alloy (80–20 wt %) in LiCl-KCl salt. The measured open circuit potential of the alloy corresponded to the range of potentials where the Ni(0) and Cr(II) species are stable, indicating a preferential dissolution of Cr. Immersion testing of the alloy for 336 h confirmed significant Cr depletion (or Ni-enrichment) at the surface layer, corroborating Cr dealloying as the dominant corrosion reaction under open circuit conditions. Additionally, the application of a small anodic overpotential (0.11 V) resulted in selective Cr dissolution while a large anodic overpotential (0.25 V) resulted in co-dissolution of both Cr and Ni. Furthermore, these results demonstrate that the corrosion mechanisms of a Ni-Cr alloy in LiCl-KCl depend upon the applied potential, and thus the redox conditions of the molten salt should be carefully controlled in the design of a redox buffer to mitigate corrosion in molten salt environments.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Preparation of a uranium monocarbide anode and electrochemical characterization in molten LiCl-KCl-UCl 3

Porous uranium carbide (UC) pellets possessing moderate electrical conductivity were synthesized by reaction of UO 2 with graphite at temperatures up to 1550°C under rough vacuum. Conversions as high as 98% were achieved at soak times of 2-4 hours. The electrochemistry of the UC pellets in molten LiCl-KCl-6.5 wt% UCl 3 was explored using a variety of techniques including DC polarization methods, cyclic voltammetry, chronopotentiometry and bulk electrolysis. Here, the electrode reaction for anodic dissolution was found to be kinetically controlled by dissociation of UC to a transition state complex that was hypothesized to consist of a uranium atom partially complexed by chloride ions. Precise measurements of current efficiencies using chronopotentiometry indicated upper limits of 90.9 ± 3.4% and 98.3 +1.7/-3.7% for anode and cathode, respectively, when operating at anodic overpotentials near +300 mV. Bulk electrolysis of a UC pellet performed by passing 98% of the theoretical charge resulted in nearly complete recovery of its uranium content as highly pure metal at the cathode.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Precious metal oxygen-evolving anodes for electrolytic reduction of metal oxides in molten LiCl-Li 2 O electrolyte

Understanding the electrochemical stability of oxygen-evolving anode materials in molten salt electrolytes is essential to enable decarbonized electrolytic reduction of metal oxides (e.g., used nuclear oxide fuels). Here, this work investigated three precious metals (Ir, Ru, and Pt) as oxygen-evolving anodes in molten LiCl-Li 2 O (99.0-1.0 wt%) at 650 °C. For consistent measurements, this work employed a three-electrode cell comprised of a two-phase Li-Bi (65-35 at%) reference electrode and a NiO counter electrode. Anodic polarization behavior of each anode was investigated via cyclic voltammetry (CV) and chronoamperometry. The onset potential for oxygen evolution was observed at E > 2.9 V (vs. Li/Li + ) for the Ir and Ru anodes and anodic current density was as high as 1.0 A cm -2 at 3.23 V. The dimensional stability of each anode was evaluated from long-term electrolysis experiments (10.0-32.1 h) at 3.23 V. Rapid consumption of the Pt anode was observed after the application of 26,453 C cm -2 with a reduction in diameter of about 15.8% due to the formation of a non-protective Li 2 PtO 3 compound. The formation of this compound was also observed during CV measurements as additional anodic waves at potentials more negative than that of oxygen evolution. In contrast, both the Ir and Ru anodes exhibited excellent dimensional stability with a reduction in diameter or thickness of less than 1.5% even after applying greater charge density of ~41,100 C cm -2 , demonstrating superior stability during oxygen evolution in the LiCl-Li 2 O electrolyte.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Differential Ligation Alters Electronic State and Coupling Signals of Iron-Sulfur Clusters in Flavin-Based Electron Bifurcation

Flavin-based electron bifurcation (FBEB) is employed by microorganisms for controlling pools of redox equivalents by reversibly splitting electron pairs into high- and low-energy levels from an initial midpoint potential. Our ability to harness this phenomenon is crucial for biocatalytic design which is limited by our understanding of energy coupling in the bifurcation system. In Pyrococcus furiosus, FBEB is carried out by the NADH-dependent ferredoxin:NADP+-oxidoreductase (NfnSL), coupling the uphill reduction of ferredoxin in NfnL to the downhill reduction of NAD+ in NfnS from oxidation of NADPH. Flanking the bifurcating flavin are two site-differentiated iron-sulfur clusters; the nearest is a glutamate-ligated [4Fe-4S] cluster in NfnL. Recent biochemical experiments substituting the native glutamate with cysteine led to loss of coupling between the uphill and downhill pathways, in contrast to the tight thermodynamic coupling in the native system. To understand how this decoupling is biochemically manifested by the cysteine-substituted [4Fe-4S] in NfnL, we employed electron paramagnetic resonance (EPR) spectroscopy to identify changes in electronic architecture and square wave voltammetry (SWV) to probe thermodynamic shifts produced by the substitution. We observed notable g-value shifts in the EPR for the cysteine-substituted iron-sulfur cluster in addition to significant downward shifts in the redox potential, as well as the disappearance of several low-field signals observed in the native NfnSL complex. These results suggest the site-differentiated glutamate residue facilitates higher spin states in the [4Fesingle bond4S] cluster to bridge energetic gaps in electron transfer to the bifurcating flavin in the native complex, preventing unwanted short-circuiting seen in the cysteine-substituted complex.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Assessing the coating implications of slurry formulations in NCMA and LFMP blend cathodes for lithium-ion batteries

This paper investigates the implications of slurry formulations and electrode processing on the performance of lithium-ion battery (LIB) cathodes, focusing on Nickel Cobalt Manganese Aluminum (NCMA) and Lithium Ferro Manganese Phosphate (LFMP) blends. Through a comprehensive examination of electrode processing steps, from material selection to coating application, we elucidate the critical role of processing parameters in shaping electrode morphology and electrochemical behavior. Rheological studies reveal the influence of slurry composition on viscosity and flow behavior, highlighting the importance of achieving optimal rheological properties for uniform coating deposition. Electrochemical characterization, including cyclic voltammetry and rate capability tests, unveils the electrochemical behavior of NCMA, LFMP, and their blend, showcasing the synergistic effects of material blending on battery performance. In conclusion, our findings underscore the intricate relationship between slurry formulation, electrode processing, and LIB performance, offering valuable insights for the design and optimization of high-performance electrode materials for next-generation batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Tetrahedral Zn 2+ doping LiNi 0.6 Mn 0.2 Co 0.2 O 2 improves discharge capacity retention by altering surface Ni valence during cycling and preventing oxygen evolution

5 mol-% Zn 2+ was added to the co-precipitation synthesis of LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) to understand Zn's effect on the structural and electronic properties of NMC622. Zn is determined to successfully dope into the NMC crystal lattice as there is an increase in d-spacing along the [003], [104], and [110] directions and an increase in molar volume (100.75 cm 3 mol -1 for NMC622 and 101.00 cm 3 mol -1 for Zn-NMC). Through XPS, Zn is determined to dope on the tetrahedral 6c Wyckoff site in the NMC structure and TEM-EDS reveals that despite a slight ZnO impurity phase, 1.4 mol-% Zn successfully dopes into the crystal structure. Furthermore, cyclic voltammetry shows a suppressed anodic wave associated with oxygen evolution and EIS demonstrates that Zn-doped NMC decreases charge transfer resistance and increases Li diffusion by an order of magnitude. After the formation cycles, NMC has a higher 1 C accessible capacity, 141 mAh/g, over Zn-NMC (132 mAh/g), but after long term cycling Zn-NMC has a higher accessible capacity (117 mAh/g compared to 96 mAh/g for NMC) and increases discharge capacity retention by 18% leading to longer cycle life.

Electrochemistry↗
DOE OSTI2025

3D printed polymer gaskets for custom-form batteries

Additive manufacturing (AM) processes, like 3D printing, help to facilitate complex and customizable battery geometries which can provide design freedom and enhance volumetric energy density within electronic devices. AM materials must have the thermal and mechanical properties that enable printability, and when used in batteries, AM materials must also be chemically and electrochemically compatible with the battery chemistry. The compatibility between AM materials and the battery is of particular importance for the cell packaging materials which must be inert and are often overlooked. This study systematically studies AM-compatible polymeric materials for use as gaskets in lithium-ion cells. The materials investigated include three thermoplastics suitable for material extrusion printing: polylactic acid (PLA), polycarbonate, and polypropylene/polyethylene copolymer (PPPEC); and two photoresins suitable for vat photopolymerization (VPP) printing: an acrylate-based photoresin and a polyethylene glycol diacrylate photoresin. The AM gasket materials were tested in comparison to a conventional commercial polypropylene gasket. Mechanical testing (swell measurements and material stiffness) and electrochemical testing (linear sweep voltammetry and galvanostatic cycling of full cells) demonstrated that PLA and the VPP polymers were the least compatible with the lithium-ion battery chemistry, despite their prevalent use in studies of AM batteries, and that PPPEC was the most compatible.

3D printing↗
DOE OSTI2024

Dynamics of precatalyst conversion and iron incorporation in nickel-based alkaline oxygen evolution reaction catalysts

The efficiency of alkaline water electrolyzers is limited by the oxygen evolution reaction (OER). The design of improved OER catalysts requires understanding of material changes induced by the electrolyte under oxidizing potentials. We compare four Ni-based thin-film precatalysts—Ni, NiO, Ni(OH) 2 , and NiS x —in 0.1 M KOH with and without Fe impurities. Precatalyst conversion to the active oxyhydroxide catalysts and their OER performance are induced and followed using cyclic voltammetry. Without Fe electrolyte impurities, the precatalysts convert at different rates to a similar, modestly active NiOOH catalyst. Added Fe impurities are incorporated concurrently with the oxyhydroxide formation leading to active Ni 1-x Fe x OOH catalysts. The NiS x and Ni(OH) 2 precatalysts rapidly convert to oxyhydroxides both with and without Fe, while conversion of Ni and especially NiO is slowed down by Fe impurities. Choice of the precatalyst and presence of Fe impurities are key factors in designing active Ni 1-x Fe x OOH OER catalysts for electrolyzers.

alkaline electrolysis↗
DOE OSTI2024

A Free-Standing Boron-Doped Diamond Grid Electrode for Fundamental Spectroelectrochemistry

Spectroelectrochemistry (SEC) is a powerful technique that enables a variety of redox properties to be studied, including formal potential (E o ), thermodynamic values (ΔG, ΔH, ΔS), diffusion coefficient (D), electron transfer stoichiometry (n), and others. SEC requires an electrode which light can pass through while maintaining sufficient electrical conductivity. This has been traditionally composed of metal or metal oxide films atop transparent substrates like glass, quartz, or metallic mesh. Robust electrode materials like boron-doped diamond (BDD) could help expand the environments in which SEC can be performed, but most designs are limited to thin films (~100–200 nm) on transparent substrates less resilient than free-standing BDD. Here, this work presents a free-standing BDD grid electrode (G-BDD) for fundamental SEC measurements, using the well-characterized Fe(CN) 6 3–/4– redox couple as proof-of-concept. With a combination of cyclic voltammetry (CV), thin-layer SEC, and chronoabsorptometry, several of the redox properties mentioned above were calculated and compared. For E o' , n, and D, similar results were obtained when comparing the CV [E o' = +0.279 (±0.002) V vs Ag/AgCl; n = 0.97; D = 4.1 × 10 –6 cm 2 ·s –1 ] and SEC [E o' = +0.278 (±0.001) V vs Ag/AgCl; n = 0.91; D = 5.2 × 10 –6 cm 2 ·s –1 ] techniques. Both values align with what has been previously reported. To calculate D from the SEC data, modification of the classical equation used in chronoabsorptometry was required to accommodate the G-BDD electrode geometry. Overall, this work expands on the applicability of SEC techniques and BDD as a versatile electrode material.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Microelectrode Arrays for Electrochemical Cycling of Individual Battery Particles

The electrochemical characterization of battery materials is usually performed on porous electrodes containing conductive additives, binders, and ensembles of redox-active particles at densities as high as 10 15 cm –3 . These complex structures often obscure individual battery particles’ intrinsic properties, hindering insights into the fundamentals of battery electrochemistry. To address this challenge, we developed microelectrode arrays to enable the charge and discharge of individual battery particles in liquid electrolytes. In this Methods and Protocols paper, we describe the fabrication of the microelectrode array chips, the assembly of particles onto microelectrodes, and the different types of electrochemical techniques that can be used, including galvanostatic cycling, cyclic voltammetry, potentiostatic intermittent titration, and electrochemical impedance spectroscopy. We use micron-sized lithium cobalt oxide as a model system to showcase the reliability and versatility of single-particle electrochemical experiments enabled by our microelectrode array. In conclusion, we aim to provide a detailed description to promote future uses of microelectrode arrays in fundamental research of batteries and other electrochemical systems.

25 ENERGY STORAGE↗
DOE OSTI2025

Surface Manipulation on Pt 2.2 Ni(111) Nanocatalysts for Boosting Their ORR Performance in Alkaline Media

We have previously shown that Pt–Ni alloy nano-octahedra with {111} facets exhibit outstanding electrochemical performance in the oxygen reduction reaction (ORR) in acidic media when their surfaces are finely tailored at the atomic level. Here, in this investigation, we further refine the surface structure of Pt 2.2 Ni octahedral nanocatalysts to improve ORR performance in a 0.1 M KOH solution using diverse surface manipulation techniques. Through systematic analysis using electrochemical CO stripping, cyclic voltammetry, and X-ray photoelectron spectroscopy, we examined the surfaces of Pt 2.2 Ni octahedral nanocatalysts pretreated with various methods, including etching in acetic acid or perchloric acid, and subsequent electrochemical activation in an alkaline solution or an acidic solution. Among these treatments, those involving acidic media, particularly electrochemical cycling in acidic electrolytes, demonstrated significantly enhanced ORR activity in 0.1 M KOH. The latter exhibited a mass activity of 2.95 A/mg pt and a specific activity of 8.71 mA/cm 2 at 0.90 V, surpassing state-of-the-art Pt/C by 12-fold and 34-fold, respectively. Furthermore, this identified nanocatalyst displayed robust stability, with negligible activity decay observed after 10,000 cycles. This study suggests that the improved ORR activity can be attributed to the Pt-rich surfaces with well-preserved {111} lattices on the surface-modified Pt–Ni nano-octahedra.

36 MATERIALS SCIENCE↗