Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “triaxial loading”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2015

Experimental and Numerical Analysis of Triaxially Braided Composites Utilizing a Modified Subcell Modeling Approach

A combined experimental and analytical approach was performed for characterizing and modeling triaxially braided composites with a modified subcell modeling strategy. Tensile coupon tests were conducted on a [0deg/60deg/-60deg] braided composite at angles [0deg, 30deg, 45deg, 60deg and 90deg] relative to the axial tow of the braid. It was found that measured coupon strength varied significantly with the angle of the applied load and each coupon direction exhibited unique final failures. The subcell modeling approach implemented into the finite element software LS-DYNA was used to simulate the various tensile coupon test angles. The modeling approach was successful in predicting both the coupon strength and reported failure mode for the 0deg, 30deg and 60deg loading directions. The model over-predicted the strength in the 90deg direction; however, the experimental results show a strong influence of free edge effects on damage initiation and failure. In the absence of these local free edge effects, the subcell modeling approach showed promise as a viable and computationally efficient analysis tool for triaxially braided composite structures. Future work will focus on validation of the approach for predicting the impact response of the braided composite against flat panel impact tests.

Polymer Matrix Composites↗
NASA NTRS2015

Experimental and Numerical Analysis of Triaxially Braided Composites Utilizing a Modified Subcell Modeling Approach

A combined experimental and analytical approach was performed for characterizing and modeling triaxially braided composites with a modified subcell modeling strategy. Tensile coupon tests were conducted on a [0deg/60deg/-60deg] braided composite at angles of 0deg, 30deg, 45deg, 60deg and 90deg relative to the axial tow of the braid. It was found that measured coupon strength varied significantly with the angle of the applied load and each coupon direction exhibited unique final failures. The subcell modeling approach implemented into the finite element software LS-DYNA was used to simulate the various tensile coupon test angles. The modeling approach was successful in predicting both the coupon strength and reported failure mode for the 0deg, 30deg and 60deg loading directions. The model over-predicted the strength in the 90deg direction; however, the experimental results show a strong influence of free edge effects on damage initiation and failure. In the absence of these local free edge effects, the subcell modeling approach showed promise as a viable and computationally efficient analysis tool for triaxially braided composite structures. Future work will focus on validation of the approach for predicting the impact response of the braided composite against flat panel impact tests.

Micromechanics↗
NASA NTRS1998

Mechanics of Granular Materials (MGM) Microgravity Experiment

The second series of MGM experiment was conducted during the STS-89 mission in January 1998. The experiment was previously flow on Atlantis's STS-79 mission in September 1996. Six displacement-controlled, drained triaxial compression experiments were performed at very low effective confining stresses. The confining stresses were in the ranges 0.05, 0.52 and 1.30 kPa. Three experiments were subjected to monotonic loading and unloading cycles while the other three experiments were subjected to cyclic loading. The results show very high peak strength friction angles in the range of 47.6 to 70.0 degrees, which are mainly due to overconsolidation and grain interlocking effects. It was observed that the residual strength levels in the monotonic loading experiments were in the same range as that observed at higher confining stress levels. The dilatancy angles were unusually high in the range of 30 to 31 degrees. All specimens display substantial initial stiffnesses and elastic moduli during unloading and reloading events, which are nearly an order of magnitude higher than conventional theories predict. A periodic instability phenomenon which appears to result from buckling of multiple internal arches and columnar systems, augmented by stick-slips was observed in the experiments. Computed Tomography (CT) measurements revealed valuable data about the internal fabric and the specimens deformation patterns. Uniform diffuse bifurcation with multiple radial shear bands was observed in the specimens tested in a microgravity environment. In the axial direction, two major conical surfaces were developed. Spatial nonsymmetrical deformations were observed in specimens tested in terrestrial laboratory.

Alshibli, Khalid A.↗
DOE OSTI2025

Failure Strain and Related Triaxiality of Aluminum 6061-T6, A36 Carbon Steel, 304 Stainless Steel, and Nitronic 60 Metals, Part I: Experimental Investigation

The objective of this study is to develop failure-limit material models for Aluminum 6061-T6, A36 Carbon Steel, 304 Stainless Steel, and Nitronic 60 metals, based on parameters of plastic equivalent strain (failure strain) and stress triaxiality. The research is conducted in two parts. This paper presents Part One of the study. In Part One, custom-designed test specimens undergo controlled uniaxial tension and compression testing at ambient temperature. These tests are performed at quasi-static speeds using Universal Testing Machines (UTMs) in accordance with ASTM E8 and ASTM E9 standards. Experimental data, specifically engineering stress–strain and force–displacement curves, are recorded from the onset of loading until specimen fracture, or in the case of compression tests, until the capacity of the testing machine is reached. In Part Two, the emphasis shifts to the calibration of Finite Element Analysis (FEA) models of the custom-designed test specimens. Plastic equivalent strain and the corresponding stress triaxiality values at failure are extracted from each test specimen for the given metal. These values are then systematically plotted onto a single graph to construct the failure-limit curve, which delineates the boundary conditions for material failure. This approach will facilitate the development of a comprehensive material property definition that correlates plastic equivalent strain with stress triaxiality at failure for Aluminum 6061-T6, A36 Carbon Steel, 304 Stainless Steel, and Nitronic 60 metals.

Harwell, Ron↗
DOE OSTI2025

Compression–tension cell with sample manipulator for in situ X‐ray nanotomography experiments

In situ X-ray nanotomography experiments where tensile or compressive force is applied on the sample require specialized equipment. A compression-tension device with fluid flow-through capability has been designed for X-ray nanotomography beamlines. The compression-tension cell is equipped with a triaxial stage for sample alignment and a high sensitivity loadcell for measurement of applied force. To handle the <100 µm samples used for X-ray nanotomography imaging and for loading samples on the compression-tension cell a sample manipulator has been built. The sample manipulator is capable of selecting a single <100 µm particle for nanotomography scanning while viewing multiple samples under an optical microscope. To test the functionality of these two devices an initial compression experiment involving two glass beads was performed. To demonstrate instrument stability two spherical glass beads were compressed from a no load condition until one of the beads fractured. Nanotomography data were collected at each step of increasing compressive force. The experimentally observed contact area of the spherical glass beads was compared with the theoretical estimate using the Hertz analysis. To demonstrate the fluid flow capability, two calcite grains were compressed against each other under a calcite saturated solution. Surface topological changes were observed for the stressed grain contact area.

X-ray tomography↗
NASA NTRS1990

Regolith-structure modeling of lunar facilities

The mechanical properties of lunar regolith are significantly different from terrestrial soils; at low stress levels, the ultimate strength envelope is highly nonlinear, and the material is essentially dilatant. The effects of platen friction, membrane confinement, and material self weight in triaxial tests have been shown to be of great significance in low stress level tests. An inverse identification technique has been devised to account for these effects where the load-displacement response of the entire specimen, including the boundary conditions and the self-weight, was analyzed by nonlinear finite element techniques so as to obtain true material parameters.

Perkins, Steven W.↗
DOE OSTI2021

Impact-induced twinning in a magnesium alloy under different stress conditions

We investigate deformation twinning in a highly textured magnesium alloy plate of Mg-3.1%Al-0.9%Zn-0.4%Mn under edge-on impact with in situ, synchrotron-based, ultrafast X-ray diffraction measurements, and corresponding stress states are simulated with the finite element method. Deformation twinning and its anisotropy under the triaxial stress condition are explained by a statistical analysis of resolved shear stress. The critical resolved shear stress criterion is applicable under complicated stress conditions induced by high strain rate impact loading. Three typical simple stress conditions are further explored as verification and application cases: uniaxial-stress, uniaxial-strain, and plane-stress. Extension twinning in the magnesium alloy is prone to occur for impact loading applied perpendicular to the crystallographic c-axis, regardless of the exact stress conditions.

36 MATERIALS SCIENCE↗
NASA NTRS2004

Investigation of Three-Dimensional Stress Fields and Slip Systems for FCC Single Crystal Superalloy Notched Specimens

Metals and their alloys, except for a few intermetallics, are inherently ductile, i.e. plastic deformation precedes fracture in these materials. Therefore, resistance to fracture is directly related to the development of the plastic zone at the crack tip. Recent studies indicate that the fracture toughness of single crystals depends on the crystallographic orientation of the notch as well as the loading direction. In general, the dependence of crack propagation resistance on crystallographic orientation arises from the anisotropy of (i) elastic constants, (ii) plastic deformation (or slip), and (iii) the weakest fracture planes (e.g. cleavage planes). Because of the triaxial stress state at the notch tips, many slip systems that otherwise would not be activated during uniaxial testing, become operational. The plastic zone formation in single crystals has been tackled theoretically by Rice and his co-workers and only limited experimental work has been conducted in this area. The study of the stresses and strains in the vicinity of a FCC single crystal notch tip is of relatively recent origin. We present experimental and numerical investigation of 3D stress fields and evolution of slip sector boundaries near notches in FCC single crystal tension test specimens, and demonstrate that a 3D linear elastic finite element model that includes the effect of material anisotropy is shown to predict active slip planes and sectors accurately. The slip sector boundaries are shown to have complex curved shapes with several slip systems active simultaneously near the notch. Results are presented for surface and mid-plane of the specimens. The results demonstrate that accounting for 3D elastic anisotropy is very important for accurate prediction of slip activation near FCC single crystal notches loaded in tension. Results from the study will help establish guidelines for fatigue damage near single crystal notches.

Arakere, Nagaraj K.↗
DOE OSTI2022

Evaluation of Hopper Flow Prediction based on Cubical Triaxial Tester Data and FEM

A cubical triaxial tester (CTT) laboratory device was used to collect key bulk flow characteristics of Crumbles® 6mm rotary sheared woody biomass and Crumbles® 2mm rotary sheard corn stover. The flow properties and a CAD model of a hopper and conveyor system to predict the consistency of flow of material from the hopper. Prediction included the likeliness of jamming, bridging, or ratholing. Each material was then loaded into the hopper and the actual bulk flow was measured. Measured flow closely matched the predicted flow.

09 BIOMASS FUELS↗
NASA NTRS2008

Full-field Strain Methods for Investigating Failure Mechanisms in Triaxial Braided Composites

Composite materials made with triaxial braid architecture and large tow size carbon fibers are beginning to be used in many applications, including composite aircraft and engine structures. Recent advancements in braiding technology have led to commercially viable manufacturing approaches for making large structures with complex shape. Although the large unit cell size of these materials is an advantage for manufacturing efficiency, the fiber architecture presents some challenges for materials characterization, design, and analysis. In some cases, the static load capability of structures made using these materials has been higher than expected based on material strength properties measured using standard coupon tests. A potential problem with using standard tests methods for these materials is that the unit cell size can be an unacceptably large fraction of the specimen dimensions. More detailed investigation of deformation and failure processes in large unit cell size triaxial braid composites is needed to evaluate the applicability of standard test methods for these materials and to develop alternative testing approaches. In recent years, commercial equipment has become available that enables digital image correlation to be used on a more routine basis for investigation of full field 3D deformation in materials and structures. In this paper, some new techniques that have been developed to investigate local deformation and failure using digital image correlation techniques are presented. The methods were used to measure both local and global strains during standard straight-sided coupon tensile tests on composite materials made with 12 and 24 k yarns and a 0/+60/-60 triaxial braid architecture. Local deformation and failure within fiber bundles was observed, and this local failure had a significant effect on global stiffness and strength. The matrix material had a large effect on local damage initiation for the two matrix materials used in this investigation. Premature failure in regions of the unit cell near the edge of the straight-sided specimens was observed for transverse tensile tests in which the braid axial fibers were perpendicular to the specimen axis and the bias fibers terminated on the cut edges in the specimen gage section. This edge effect is one factor that could contribute to a measured strength that is lower than the actual material strength in a structure without edge effects.

Littell, Justin D.↗
NASA NTRS1982

On the stability of Schwarzschild's triaxial galaxy model

The numerical model for a triaxial galaxy constructed by Schwartzschild (1979) has been tested by means of fully self-consistent three-dimensional n-body numerical experiments that use a representation of this model to start the integration. The integration, study models, initial load, and correcting potential of the experiment are detailed. Preliminary checks included density values, potential values, and integration in potential of an ideal model. The results showed some particle loss and no significant shape change. The model is rugged and robust, and no growing disturbances with growth rate in excess of 0.5 per crossing time could be detected. Runs were done at 50 percent excess halo and with tube orbits reversed.

Smith, B. F.↗
NASA NTRS2004

Ballistic Impact of Braided Composites With a Soft Projectile

Impact tests using a soft gelatin projectile were performed to identify failure modes that occur at high strain energy density during impact loading. Use of a soft projectile allows a large amount of kinetic energy to be transferred into strain energy in the target before penetration occurs. Failure modes were identified for flat aluminum plates and for flat composite plates made from a triaxial braid having a quasi-isotropic fiber architecture with fibers in the 0 and +/- 60 deg. directions. For the aluminum plates, a large hole formed as a result of crack propagation from the initiation site at the center of the plate to the fixed boundaries. For the composite plates, fiber tensile failure occurred in the back ply at the center of the plate. Cracks then propagated from this site along the +/- 60 deg. fiber directions until triangular flaps opened to allow the projectile to pass through the plate. The damage size was only slightly larger than the initial impact area. It was difficult to avoid slipping of the fixed edges of the plates during impact, and slipping was shown to have a large effect on the penetration threshold. Failure modes were also identified for composite half-rings fabricated with the 0 deg. fibers aligned circumferentially. Slipping of the edges was not a problem in the half-ring tests. For the composite half-rings, fiber tensile failure also occurred in the back ply. However, cracks initially propagated from this site in a direction transverse to the 0 deg. fibers. The cracks then turned to follow the +/- 60 deg. fibers for a short distance before turning again to follow 0 deg. fibers until two approximately rectangular flaps opened to allow the projectile to pass through the plate. The damage size in the composite half-rings was also only slightly larger than the initial impact area. Cracks did not propagate to the boundaries, and no delamination was observed. The damage tolerance demonstrated by the quasi-isotropic triaxial braid composites indicate that composites of this type can reasonably be considered as a lightweight alternative to metals for fan cases in commercial jet engines.

Roberts, Gary D.↗
NASA NTRS1988

Internal structure and shape of Mimas

The observed triaxial ellipsoid shape of Mimas, in conjunction with a mean density of 1137 kg/cu cm, is presently used as the basis of hydrostatic equilibrium and nonhydrostatic models of internal structure whose outer layers are sufficiently strong to support part of the tidal load. Such plausible internal structures are consistent with the shape and density constraints as (1) a two-layer model in hydrostatic equilibrium, (2) a hydrostatic model with four layers of equal depth, and (3) a nonhydrostatic constant-density model with an elastic lithosphere; these models admit either homogeneous or heterogeneous accretion, as well as either a cold thermal history or melting and differentiation.

Ross, M. N.↗
NASA NTRS2018

NASA ACC High Energy Dynamic Impact Methodology and Outcomes

For High Energy Dynamic Impact (HEDI) events, testing to evaluate the structural response of primary aircraft structure for design and certification is both expensive and time consuming. This paper discusses current work seeking to assess, develop, and validate appropriate analytical models that accurately predict physical response, damage, and failure modes for large scale composite structures in HEDI events. Four state-of-the-art Progressive Damage Analysis (PDA) methods were employed for this phased project: LS-DYNA MAT162, LS-DYNA MAT261, Smoothed Particle Galerkin (SPG), and EMU Peridynamics. Multiple material systems were considered, namely T700/5208 textile-infusion triaxial braid, T800/AMD-825 textile-infusion triaxial braid, IM7/8552 uni-directional tape, and SPG 196-PW/8552 plain-weave fabric. Extensive ballistic impact testing was performed to support this activity and measured results were compared to predictive models for assessment using panel delamination, panel displacement, force at the load cells, and threshold velocity as measures. Ultimately, the work under this activity provided significant progress in advancing the state-of-the-art in the use of PDA for HEDI events. Each material model had favorable performance comparing to test in some parameters and needed improvement in others. With the lessons learned from this activity, significant progress was made in the ability to predict panel behavior for a more general case beyond the flat panel in a ballistic impact event. Subsequent Phase II of the NASA ACC HEDI effort will continue to build on the coupon testing, flat panel ballistic impact testing, and analysis performed to-date with application of the PDA methods for intended material selections to test articles with greater complexity of configuration, curvature, and scale. It is not the intention of this paper to present a full set of data, but rather to give an overview of the NASA HEDI effort and show a small representative subset of the test and analysis results.

Hunziker, Kenneth J.↗
NASA NTRS2016

Development of a Subcell Based Modeling Approach for Modeling the Architecturally Dependent Impact Response of Triaxially Braided Polymer Matrix Composites

Understanding the high velocity impact response of polymer matrix composites with complex architectures is critical to many aerospace applications, including engine fan blade containment systems where the structure must be able to completely contain fan blades in the event of a blade-out. Despite the benefits offered by these materials, the complex nature of textile composites presents a significant challenge for the prediction of deformation and damage under both quasi-static and impact loading conditions. The relatively large mesoscale repeating unit cell (in comparison to the size of structural components) causes the material to behave like a structure rather than a homogeneous material. Impact experiments conducted at NASA Glenn Research Center have shown the damage patterns to be a function of the underlying material architecture. Traditional computational techniques that involve modeling these materials using smeared homogeneous, orthotropic material properties at the macroscale result in simulated damage patterns that are a function of the structural geometry, but not the material architecture. In order to preserve heterogeneity at the highest length scale in a robust yet computationally efficient manner, and capture the architecturally dependent damage patterns, a previously-developed subcell modeling approach where the braided composite unit cell is approximated as a series of four adjacent laminated composites is utilized. This work discusses the implementation of the subcell methodology into the commercial transient dynamic finite element code LS-DYNA (Livermore Software Technology Corp.). Verification and validation studies are also presented, including simulation of the tensile response of straight-sided and notched quasi-static coupons composed of a T700/PR520 triaxially braided [0deg/60deg/-60deg] composite. Based on the results of the verification and validation studies, advantages and limitations of the methodology as well as plans for future work are discussed.

finite element method↗
DOE OSTI2022

Influence of weave architecture on mechanical response of SiC f -SiC m tubular composites

Due to their high resistance to radiation damage and elevated temperature, silicon carbide fiber-reinforced, silicon carbide matrix composites (SiC f -SiC m ) are identified as potential cladding structures for use in nuclear reactors. In this study, four composite architectures with varying ply numbers along the thickness direction and different biaxial or triaxial plain weave orientations at either 45° or 60°, were systematically evaluated under various stress states to assess the influence of weave architecture on mechanical performance. Experiments were conducted on SiC f -SiC m composite tubes under tensile hoop, axial compression, and rotating flexural loading to evaluate the mechanical response and investigate the failure modes using high-speed imaging and digital image correlation (DIC) techniques. It was found that for tensile hoop burst and flexural loading, the braiding angle had the most significant influence on the strength of the composite, whereas the effect of fiber angle was more limited for compression testing. Under axial compression a unique failure mode where a microcrack nucleates and grows only to a length equal to the thickness of a single yarn was identified. This crack growth behavior is reflected as periodic oscillations in the load-displacement response. For both axial and hoop loading, regardless of weave angle and number of plies, failure always initiated parallel to the tube axis in a single yarn and the cumulative interaction of these microcracks lead to either axial burst or fracture at an angle to the tube axis along a yarn. Furthermore, these results point to the importance of customizing the design of tube architecture for enhanced performance in specified nuclear applications.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Role of crystallographic orientation on intragranular void growth in polycrystalline FCC materials

In this study, we study the effect of crystallographic orientation and applied triaxiality on the growth of intragranular voids. Two 3D full-field micromechanics methods are used, the dilatational visco-plastic fast-Fourier transform (DVP-FFT) and the crystal plasticity Finite Elements (CP-FE), both of which incorporate a combination of crystalline plasticity and dilatational plasticity. We demonstrate with several select cases that predictions of void growth from both formulations agree qualitatively. With the more computationally efficient DVP-FFT, additional effects of polycrystalline microstructure and the influence of nearest neighborhood are investigated. Crystals bearing a single intracrystalline void are studied in three types of 3D microstructural environments: isolated single crystals, individual equal-sized grains within a regular polycrystal, and individual variable sized grains within a polycrystal with grains and voids randomly located. We show that loading type plays a significant role. In strain-rate controlled conditions, voids in the hardest [111]-crystals grow the fastest in time, whereas in stress-controlled conditions, voids in the softest [100]-crystal grow the fastest in time. The analysis reveals that on average void growth is slower for the same starting orientation in the polycrystal than in the single crystal. We find that at the highest triaxiality tested that the correlation between crystal orientation and void growth rate in the polycrystal strengthens, drawing closer to that seen in the isolated single crystals. These results and model can help guide the microstructural design of polycrystalline materials with high strength and damage-tolerance in high-rate deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Machine-Learning-Based Multiscale Methods for 3D Modelling of Granular Materials by Incorporating History-Dependent State Variables

Over the past decades, the prevalence of machine learning (ML) methods has made the development of ML-based constitutive models for granular materials undoubtedly a popular subject. Numerous studies have been made to feature the loading path or history-dependent stress-strain response of granular media using neural networks. In this work, a novel finite element method (FEM)–ML multiscale approach was developed by incorporating internal variables to improve the simulation accuracy of 3D history-dependent granular materials for the first time. To this end, a surrogate constitutive model based on the single-step-based multi-layer perceptron (MLP) neural network was used to replace representative volume element (RVE) simulations conducted by the discrete element method (DEM) in the multiscale FEM–DEM approach. Although the prediction principle of the MLP aligns with the FEM algorithm, artificially added internal variables are required to differentiate the loading history. To address this issue, history variables associated with the Frobenius norm are proposed to be fed into the MLP coupled with the strain tensor to extract the history-dependent behaviour of granular assemblies. The developed FEM–ML approach was demonstrated in 3D conventional triaxial compression (CTC) simulations. Compared to the multiscale FEM–DEM approach, the proposed FEM–ML method exhibits a significantly improved computational efficiency.

granular materials↗