Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “total electron yield”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1983

Reflectance Measurements, Part 2

Improving the productivity of spectroreflectometer readings taken to monitor induced contamination of lenses, mirrors, and coatings in the space environment are described. More sophisticated modelling techniques were applied to the laboratory data collected last summer in order to produce a more accurate model of the nonlinearities and noise sources of the instrumentation. This would ultimately allow for correction of known anomalies by the digital computer, yielding an anticipated order to magnitude improvement in the accuracy of the reflectance measurements, while reducing the total measuring time. The construction of and programming for a modernized version of the electronics used in Beckman DK-2 spectroreflectometers suffered because of a schedule lag in fabrication of a modified form of the carrier frequency pickoff. Separate development of the electronics and the computer programming was partially accomplished.

Brown, R. A.↗
NASA NTRS1988

Critical velocity experiments in space

Published data from active space experiments designed to demonstrate the Alfven critical-velocity effect are compiled in graphs and compared with the predictions of numerical simulations. It is found that the discrepancies in the ionization yields obtained in shaped-charge releases of alkali metals are related to the macroscopic limits of time and energy in such releases. It is argued that the total ionization yield is an inadequate measure of the critical-velocity effect, and a new criterion based on eta, the efficiency of energy transfer from the recently ionized neutrals to a heated electron population, is proposed: the effect would be verified if eta values of 10 percent or greater were observed.

Torbert, R. B.↗
NASA NTRS1992

Upflowing ionospheric ions in the auroral region

Observations of upflowing ionospheric ions are obtained nearly simultaneously by DE 1 and DE 2 over the nightside auroral regions. At low altitudes, the mean value of the net upward ion number flux is of the order of 10 exp 9/sq cm per sec. The ionosphere is predominantly O(+), and the flux of ions with energy greater than 5 eV is a very small fraction (less than 1 percent) of the total ion flux. At high altitudes, the upflowing ions are accelerated by a parallel electric field and heated (with characteristic energies of hundreds of electron volts). Comparing upflowing fluxes at high and low altitudes yields an estimated height of the bottom of the auroral acceleration region of 1400-1700 km for the region of peak potential drop. This low-altitude acceleration could either be from a parallel electric field or from perpendicular acceleration. The fluxes at the edges of the arc are mostly H(+) thus implying a higher-altitude base of the acceleration region at the edges where the potential drop is lower.

Lu, G.↗
DOE OSTI2024

Cell-free bioelectrocatalytic platform for carbon dioxide reduction (Final Technical Report)

The University of Minnesota (UMN) EcoSynBio Team aimed to develop a cell-free, enzyme-based platform for the electro- biocatalytic conversion of CO2 into formate as a platform chemical for further upgrading. This type of bio electrocatalytic process delivers a clean product stream without the need for extensive separation from the electrolyte as in electrochemical synthesis and microbial processes. The reduction reaction is catalyzed by metal-dependent formate dehydrogenases (mFDHs) that are capable of efficient electrocatalytic CO2 reduction without the need of costly co-factors. The development of an efficient, scalable electrobiocatalytic process with high total turnover numbers and viable space time yields, however, was not without its challenges. The UM team has developed a protein-based scaffolding system that facilitates enzyme stabilization and attachment to electrodes along with electron transfer. Yet, although FDHs are highly promising enzymes for cell-free, electrobiochemical CO2 reduction, they are also greatly understudied and especially for applications in electrocatalysis. The UM team used the best described mFDH from Clostridium as its benchmark system and spent significant time and effort in attempting to replicate published data and finally, redesigned a recombinant production system for proper metal co-factor incorporation. The UM team has also identified a small set of new enzyme homologs from extreme microorganisms with superior stabilities that have yielded initial structural data for further engineering. In addition, a new bioelectrocatalytic reactor system has been developed that can be 3D printed and used for enzyme attachment to electrodes. In summary the project has generated critical basic information for the further development of this class of enzymes for the electricity driven reduction of CO2 into formate as platform chemical for upgrading into various other chemicals, including fuels.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1985

Bremsstrahlung in the scattering of low-energy electrons by neutral atomic systems

By elementary methods, the cross section for electron-atom and electron-molecule bremsstrahlung is computed in the limit when the incident electron energy is much less than Ry. The procedure employs the classical soft-photon emission probability formula for general (h/2pi)(omega), yielding a simple expression for the bremsstrahlung cross section in terms of the total elastic scattering cross section. The validity of the method is discussed, and results are compared with more elaborate and accurate calculations. Comparison is made with ('free-free') opacity calculations for the associated process at the temperature (6300 K) of the solar atmosphere. For chi sub omega = (h/2pi)(omega)/kT = 1, the computed absorption coefficient is within 2, 7, and 12 percent of accurate calculations for scatterings by H, He, and H2, respectively. The general dependence of the opacity on chi sub omega is described well by the simple formula, although the error is larger for higher chi sub omega; it is suggested that the inaccuracy at high frequencies is due to the failure of the soft-photon approximation.

Gould, R. J.↗
DOE OSTI2026

Electromagnetic Shower Reconstruction and Identification in FASER's Emulsion Detector for LHC Forward Neutrino Measurements

We present methods for electromagnetic shower reconstruction and identification in the FASERnu emulsion detector using 100 GeV and 200 GeV electron test-beam data from the CERN SPS H4 beamline. The reconstruction employs a clustering-based algorithm without energy-dependent tuning to determine shower axes. A multi-level identification chain comprising track pre-selection, a cut-based selection, and a BDT classifier achieves combined background rejection rates of 99.99% (100 GeV) and 99.94% (200 GeV). The method reaches total reconstruction and identification efficiencies of 58.9% (100 GeV) and 70.8% (200 GeV) evaluated from simulated samples. Energy reconstruction using the total number of reconstructed segments as the calorimetric estimator yields relative biases of +0.6% (100 GeV) and -0.8% (200 GeV), with resolutions of 25.4% and 22.6%, respectively. Systematic uncertainties on the energy reconstruction are dominated by variations in emulsion film detection efficiency, contributing (+10.9%/-8.2%) at 100 GeV and (+10.3%/-6.9%) at 200 GeV. The methodology provides a validated framework for electron neutrino identification with the FASERnu detector at the LHC.

Mammen Abraham, Roshan [UC, Irvine]↗
DOE OSTI2024

Leveraging hyperspectral imaging to identify drought tolerant Populus species and genotypes within species

The aim of this study was to identity variation in drought tolerance across genotypes of Populus deltoides, Populus trichocarpa, and hybrids of the two species. A panel of 102 Populus genotypes, comprising 37 genotypes of P. trichocarpa, 37 of P. deltoides and 28 unique hybrid genotypes (P. trichocarpa x P. deltoides and P. deltoides x P. trichocarpa) were evaluated in the greenhouse under two treatments, well-watered (WW) and drought (DS). Plant physiological data were collected throughout the experiment once the drought treatment began. Throughout the experiment, we tracked soil volumetric water content, pot weight, stomatal conductance, quantum yield of photosystem II, and electron transport rate. In addition to those measurements, upon completion of the experiment, we assessed above and belowground plant biomass, plant height and stem diameter, leaf number, specific leaf area, relative water content, total protein, and total chlorophyll. We obtained hyperspectral signatures of one leaf from each plant at the end of the experiment. Columns BC – LL are hyperspectral averages for one leaf from each plant at each wavelength as described in the column header.

Hyper-spectral imaging, Populus, plant stress tole↗
NASA NTRS1977

Secondary-electron-emission properties of conducting surfaces with application to multistage depressed collectors for microwave amplifiers

To improve the efficiency of high power microwave tubes, low secondary electron yield electrode surface for use in depressed collectors are needed. The secondary emission characteristics of a number of materials were investigated. The materials studied were beryllium, carbon (soot and pyrolytic graphite), copper, titanium carbide, and tantalum. Both total secondary yield delta and relative reflected primary yield were measured. These measurements were made in conjunction with Auger spectroscopy so that the secondary emission characteristics could be determined as a function of surface contamination or purity. The results show that low atomic weight elements, such as beryllium and carbon, have the lowest reflected primary yield and that roughening the surface of an electrode can markedly decrease secondary yield both for delta and reflected primaries. All factors considered, a roughened pyrolytic graphite surface showed the greatest potential for use as an electrode surface in depressed collectors.

Forman, R.↗
NASA NTRS2001

Updated Electronic Testbed System

As we continue to advance in exploring space frontiers, technology must also advance. The need for faster data recovery and data processing is crucial. In this, the less equipment used, and lighter that equipment is, the better. Because integrated circuits become more sensitive in high altitude, experimental verification and quantification is required. The Center for Applied Radiation Research (CARR) at Prairie View A&M University was awarded a grant by NASA to participate in the NASA ER-2 Flight Program, the APEX balloon flight program, and the Student Launch Program. These programs are to test anomalous errors in integrated circuits due to single event effects (SEE). CARR had already begun experiments characterizing the SEE behavior of high speed and high density SRAM's. The research center built a error testing system using a PC-104 computer unit, an Iomega Zip drive for storage, a test board with the components under test, and a latchup detection and reset unit. A test program was written to continuously monitor a stored data pattern in the SRAM chip and record errors. The devices under test were eight 4Mbit memory chips totaling 4Mbytes of memory. CARR was successful at obtaining data using the Electronic TestBed System (EBS) in various NASA ER-2 test flights. These series of high altitude flights of up to 70,000 feet, were effective at yielding the conditions which single event effects usually occur. However, the data received from the series of flights indicated one error per twenty-four hours. Because flight test time is very expensive, the initial design proved not to be cost effective. The need for orders of magnitude with more memory became essential. Therefore, a project which could test more memory within a given time was created. The goal of this project was not only to test more memory within a given time, but also to have a system with a faster processing speed, and which used less peripherals. This paper will describe procedures used to build an updated Electronic Testbed System.

Brewer, Kevin L.↗
NASA NTRS1961

A Satellite Borne Cadmium Sulfide Total Corpuscular Energy Detector

The properties of single crystals of cadmium sulfide as radiation detectors are described. It has been found possible to select crystals such that: (a) The ratio of increase of conductivity under irradiation to the rate of absorption of energy in the crystal is substantially independent of particle energy (over the examined ranges of 500 ev to 80 kev for electrons and 5 kev to 180 kev for protons) and of the magnitude of energy flux (over the range from.005 to 10 ergs/cm(sup 2 -sec); and (b) The above ration is substantially the same for protons, electrons, alpha particles, x-rays, and gamma-rays. For a driving voltage of 100 volts, typical crystal yield currents of 10(sup -7) to 10(sup- 6) amperes for each erg/cm(sup 2-sec) of energy absorbed by the crystal. The threshold of such crystal detectors (resulting from dark currents of the order of 10(sup 10 amp) is typically 10(sup -3) ergs/cm(sup 2- sec). For the selected crystals a response-temperature coefficient of -0.25% per degree centigrade is found for the temperature range -50 deg C to + 50 deg C. A description is given of a complete CdS total corpuscular energy detector for the study of geomagnetically trapped radiation by means of a satellite. The detector described has a dynamic range great than 10(sup 4), a solid angle of 10(exp -3) steradian, and a detection threshold of approximately 1 erg/cm(sup 2-sec-sterad). A similar detector employing a small magnet for the selective exclusion of electrons is also described. Noteworthy practical features of these detectors for satellite and space probe experiments are: (a) Use of bare crystals, without covering foils, in order to detect charged particles having energies as low as hundreds of electron volts. (b) Simplicity of electronic auxiliaries. (c) Compactness, lightweight and nechanical ruggedness. (d) Low electrical power requirements; and (e) Conversion of conduction current to the rate of a twostate relaxation oscillator in order to facilitate telemetric transmission of data. A pair of such detectors was flown as part of the s-46 satellite payload on March 23, 1960, but due to vehicular failure an orbit was not achieved and the operation of the CdS detectors was observed for only, six minutes of flight.

Freeman, John W.↗
NASA NTRS2003

Study of alloy disorder in quantum dots through multi-million atom simulations

A tight binding model which includes s, p, d, s orbitals is used to examine the electronic structures of an ensemble of dome-shaped In0.6 Ga0.4 As quantum dots. Given ensembles of identically sized quantum dots, variations in composition and configuration yield a linewidth broadening of less than 0.35 meV, much smaller than the total broadening determined from photoluminescence experiments. It is also found that the computed disorder-induced broadening is very sensitive to the applied boundary conditions, so that care must be taken to ensure proper convergence of the numerical results. Examination of local eigenenergies as functions of position shows similar convergence problems and indicates that an inaccurate resolution of the equilibrium atomic positions due to truncation of the simulation domain may be the source of the slow ground state convergence.

disorder↗
NASA NTRS2008

Synchrotron Photoionization Mass Spectrometry Measurements of Kinetics and Product Formation in the Allyl Radical (H2CCHCH2)Self Reaction

Product channels for the self-reaction of the resonance-stabilized allyl radical, C3H5 + C3H5, have been studied with isomeric specificity at temperatures from 300-600 K and pressures from 1-6 Torr using time-resolved multiplexed photoionization mass spectrometry. Under these conditions 1,5-hexadiene was the only C6H10 product isomer detected. The lack of isomerization of the C6H10 product is in marked contrast to the C6H6 product in the related C3H3 + C3H3 reaction, and is due to the more saturated electronic structure of the C6H10 system. The disproportionation product channel, yielding allene + propene, was also detected, with an upper limit on the branching fraction relative to recombination of 0.03. Analysis of the allyl radical decay at 298 K yielded a total rate coefficient of (2.7 +/- 0.8) x 10(exp -11) cu cm/molecule/s, in good agreement with pre.vious experimental measurements using ultraviolet kinetic absorption spectroscopy and a recent theoretical determination using variable reaction coordinate transition state theory. This result provides independent indirect support for the literature value of the allyl radical ultraviolet absorption cross-section near 223 nm.

Selby, Talitha M.↗
NASA NTRS1973

A Comparison of Near Simultaneous Lidar Returns and Particulate Collections on Filters Flown at Six Stratospheric Altitudes

Collections of particulates on both Los Alamos Scientific Laboratory (LASL) and National Center for Atmospheric Research (NCAR) filter systems were made from an RB 57F aircraft flown at one tropospheric and six stratospheric altitudes over the Boulder, Colorado, area. This daytime flight was spanned by lidar returns on evenings before and after the flight. Scanning electron microscope examination of the LASL filters showed no evidence of solid particulates greater than 2 micrometers (the instrumental resolving power). Quantitative analysis of the NCAR filters yielded chemical composition and mass. The mass values were normalized to the total air flow through the filters to yield mass mixing ratios at the various altitudes. The lidar returns, normalized to molecular densities obtained from sonde data, were put in the form of particulate scattering divided by molecular scattering, i. e., an optical mixing ratio. A plot of the optical mixing ratio versus mass mixing ratio, in the stratosphere, yielded linear relationship, for five of the six data points, going through the origin.

Schuster, Burton G.↗
NASA NTRS2021

Total X-ray Emission from the LMC Observed with HaloSat

We constrain the LMC’s global parameters by modeling the first soft X-ray (0.4–6.8 keV) observations of the entire Large Magellanic Cloud (LMC) produced in a single pointing with moderate spectral resolution by the HaloSat CubeSat. These data are best fit with the sum of two thermal plasma components in collisional ionization equilibrium and a power-law. We find cool (0.210±0.014keV) and hot (0.89±0.14keV) components. The LMC’s total X-ray luminosity is(1.08±0.14)×1039erg s−1.X-ray binaries make up a large fraction of the emission with a luminosity of(6.0±0.8)×1038ergs−1, followed by cool gas from superbubbles, supernovae, and diffuse emission with a luminosity of(3.0±0.3)×1038erg s−1. The hot gas from star formation contributes the smallest fraction, with a luminosity of(1.9±0.5)×1038erg s−1. We estimate the total volume of the cool gas to be between(0.2–1.2)×1010pc3and the hot gas to be between(1.0–5)×107pc3for filling factors off= 1and0.2. These volumes result in a total thermal energy for the cool gas between (1.4–3)×1054ergs for electron densities of 0.017–0.04 cm−3, and a thermal energy for the hot gas between (1.7–4)×1053ergs for electron densities of 0.12–0.3 cm−3. This yields cooling timescales for the cool and hot gas of(1.5–3)×108years and(1.8–6)×107years, respectively

LMC↗
DOE OSTI2025

Toward an Understanding of Linear Scaling Relations through Energy Decomposition Analysis

The discovery of linear scaling relations has fundamentally changed the field of heterogeneous catalysis. The scaling relations have been rationalized based on the d-band theory, specifically a separation of sp and d electron contributions to adsorption energies. Within the framework of energy decomposition analysis, a full understanding of such a separation would require one to further break down the adsorption energy into distinct energy components such as electrostatics, polarization, charge transfer, and van der Waals interactions, and to examine the sp and d contributions to each of them. As a step in this direction, we analyzed the interaction energy between CH x (x = 1–4) adsorbates and fcc(100) transition metal surfaces (M = Cu, Ag, Au, Rh, and Pt), with the surfaces represented both as slabs in plane-wave density functional theory (pw-DFT) calculations and as atomic clusters in atomic-orbital basis density functional theory (ao-DFT) calculations. Through an absolutely localized molecular orbital (ALMO) based energy decomposition analysis of the ao-DFT adsorption energy, each of the interaction energy components (electrostatics, polarization, van der Waals, and charge transfer) was found to follow its own scaling relations, with an intricate interplay among these energy components yielding the overall scaling relations for the total adsorption energies. Using the recently introduced ALMO-based polarization and charge-transfer analysis schemes, we further dissected polarization into metal surface and adsorbate contributions, and charge transfer into metal → adsorbate and adsorbate → metal contributions. The contributions from the sp and d electrons of the metal to these terms were further quantified, and the dominant role of the metal d electrons was reaffirmed. These results shed light on how CHx adsorbates interact with metal surfaces and further reveal the physical origin of the scaling relations.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Linear-Scaling Local Natural Orbital-Based Full Triples Treatment in Coupled-Cluster Theory

We present an efficient, asymptotically linear-scaling implementation of the canonically O(N 8 ) coupled-cluster method with singles, doubles, and full triples excitations (CCSDT) method. We apply the domain-based local pair natural orbital (DLPNO) approach for computing CCSDT amplitudes. Our method, called DLPNO–CCSDT, uses the converged coupled-cluster amplitudes from a preceding DLPNO–CCSD(T) computation as a starting point for the solution of the CCSDT equations in the local natural orbital basis. To simplify the working equations, we t1-dress our two-electron integrals and Fock matrices, allowing our equations to take on the form of CCDT. With appropriate parameters, our method can recover more than 99.99% of the total canonical CCSDT correlation energy. In addition, we demonstrate that our method consistently yields sub-kJ mol –1 errors in relative energies when compared to canonical CCSDT, and, likewise, when computing the difference between CCSDT and CCSD(T). Finally, to highlight the low scaling of our algorithm, we present timings on linear alkanes (up to 30 carbons and 730 basis functions) and water clusters (up to 131 water molecules and 3144 basis functions).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1975

The San Juan Capistrano meteorite

The San Juan Capistrano chondrite fell on 15 March 1973; the total recovered mass was 56 g. Electron microprobe, chemical and petrographic studies show it to be a member of the H group and of petrologic type 6. Rare gas studies show that only minor radiogenic gas loss has occurred and yield a K-Ar age of 4.6 billion years and a Kr-Kr exposure age of 29 million years.

Finkel, R. C.↗
NASA NTRS2016

Global Energetics of Solar Flares: Nonthermal Energies - Part III

This study entails the third part of a global flare energetics project, in which Ramaty High-Energy Solar Spectroscopic Imager (RHESSI) data of 191 M and X-class flare events from the first 3.5 years of the Solar Dynamics Observatory mission are analyzed. We fit a thermal and a nonthermal component to RHESSI spectra, yielding the temperature of the differential emission measure (DEM) tail, the nonthermal power-law slope and flux, and the thermal nonthermal cross-over energy eco. From these parameters, we calculate the total nonthermal energy E(sub nt) in electrons with two different methods: (1) using the observed cross-over energy e(sub co) as low-energy cutoff, and (2) using the low-energy cut off e(sub wt) predicted by the warm thick-target bremsstrahlung model of Kontar et al. Based on a mean temperature of T(sub e) = 8.6 MK in active regions, we find low-energy cutoff energies of e(sub wt) = 6.2 +/-1.6 keV for the warm-target model, which is significantly lower than the cross-over energies e(sub co) = 21 +/- 6 keV. Comparing with the statistics of magnetically dissipated energies E(sub mag) and thermal energies E(sub th) from the two previous studies, we find the following mean (logarithmic) energy ratios with the warm-target model: E(sub nt) = 0.41E(sub mag), E(sub th) = 0.08 E(sub mag), and E(sub th) = 0.15 E(sub nt). The total dissipated magnetic energy exceeds the thermal energy in 95% and the nonthermal energy in 71% of the flare events, which confirms that magnetic reconnection processes are sufficient to explain flare energies. The nonthermal energy exceeds the thermal energy in 85% of the events, which largely confirms the warm thick-target model.

Aschwanden, Markus J.↗