Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “thermosets”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Structural validation of a thermoplastic composite wind turbine blade with comparison to a thermoset composite blade

Reactive infusible thermoplastics have the potential to be advantageous for wind turbine blade composites because they are recyclable at end of life, can have reduced manufacturing costs, enable thermal joining and have similar, and in some cases better, structural properties than traditional thermoset epoxy composites. However, these materials are new to the wind industry and there is risk to investing in a material that has not been validated at a blade scale. Industry cannot adopt a new material such as this without large-scale validation and demonstration of system-level advantages in cost and/or performance. This paper presents structural characterization of a 13-m thermoplastic composite wind turbine blade compared to an identical geometry thermoset epoxy blade. In this work, the results of this comparison showed that the flatwise structural static performance and the fatigue performance of the two blades were similar, but the thermoplastic composite blade had increased damping compared to the epoxy blade, which may result in reduced operational loads.

17 WIND ENERGY↗
DOE OSTI2025

Synthesis, Properties, and Metathesis Activity of Polyurethane Thermoplastics and Thermosets from a Renewable Polysesquiterpene Diol

Polyurethanes (PUs) are the sixth most commonly utilized plastic class, yet ∼80% of commodity material is landfilled or incinerated at the end of life. Disposal of thermosets is particularly problematic as cross-linking prevents the repurposing of disposed material. Thus, there is considerable interest in the development of PUs derived from inexpensive feedstocks that can be inherently chemically deconstructed. Ring opening metathesis polymerization (ROMP) of the naturally occurring sesquiterpene β-caryophyllene in the presence of dihydroxy chain terminators afforded the polyol hydroxy-terminated polycaryophyllene (HTPCR). Incorporation of HTPCR into PUs through reaction with polyisocyanates produced polymers with thermal and rheological properties comparable to commodity materials. The feasibility of chemical degradation of both thermoplastic and thermoset materials was also demonstrated through ruthenium-mediated metathesis, utilizing the metathesis-active olefins within the repeat caryophyllene monomer unit. Overall, this work highlights the value of biorenewable, chemically reprocessable polysesquiterpenes in the PU space.

materials↗
DOE OSTI2024

A Mechanism-Based Reaction–Diffusion Model for Accelerated Discovery of Thermoset Resins Frontally Polymerized by Olefin Metathesis

Frontal ring-opening metathesis polymerization (FROMP) involves a self-perpetuating exothermic reaction, which enables the rapid and energy-efficient manufacturing of thermoset polymers and composites. Current state-of-the-art reaction–diffusion FROMP models rely on a phenomenological description of the olefin metathesis kinetics, limiting their ability to model the governing thermo-chemical FROMP processes. Furthermore, the existing models are unable to predict the variations in FROMP kinetics with changes in the resin composition and as a result are of limited utility toward accelerated discovery of new resin formulations. In this work, we formulate a chemically meaningful model grounded in the established mechanism of ring-opening metathesis polymerization (ROMP). Our study aims to validate the hypothesis that the ROMP mechanism, applicable to monomer-initiator solutions below 100 °C, remains valid under the nonideal conditions encountered in FROMP, including ambient to >200 °C temperatures, sharp temperature gradients, and neat monomer environments. Through extensive simulations, we demonstrate that our mechanism-based model accurately predicts the FROMP behavior across various resin compositions, including polymerization front velocities and thermal characteristics (e.g., T max ). Additionally, we introduce a semi-inverse workflow that predicts FROMP behavior from a single experimental data point. Notably, the physiochemical parameters utilized in our model can be obtained through DFT calculations and minimal experiments, highlighting the model’s potential for rapid screening of new FROMP chemistries in pursuit of thermoset polymers with superior thermo-chemo-mechanical properties.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Simulation of polymerization induced phase separation in model thermosets

Polymerization induced phase separation (PIPS) in a three component thermoset is studied using molecular dynamics simulations of a new coarse-grained thermoset model. The system includes two crosslinker molecules, which differ in their glass transition temperatures (T g ) and chain length and thus have the potential for phase separation. Here, one crosslinker has a high T g corresponding to a rubbery behavior, and simulations were performed for a short length (4 beads) and a long length (33 beads). The resin and other crosslinker have low T g . A coarse-grained model is developed with these features and with interaction parameters determined so that for either rubbery crosslinker length, the system is in the liquid state at the cure temperature. For sufficiently slow reaction rates, the long rubbery molecule exhibits PIPS into a bicontinuous array of nanoscale domains, but the short one does not, reproducing recent experimental results. The simulations demonstrate that the reaction rates must be slow enough to allow diffusion to yield phase separation. Particularly, the reaction rate corresponding to the secondary amine must be very slow, else the structure of crosslinked clusters and the substantially increased diffusion time will prevent PIPS.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Highly Recyclable Thermosets for Lightweight Composites: CRADA 517 [Abstract only]

Lightweight composites are of increasing need to enable reduced fuel usage, reduced carbon emissions and increased range in air and ground transportation. The superior weight savings of carbon fiber thermoset composites are impeded by material and production costs and the limited options available for composite repair and recycle. The materials recovery and recycling sector is currently overwhelmed by an abundance of low-value materials and limited market opportunities for downcycled content, rendering landfilling a more attractive alternative. Vitrimers represent a new paradigm for repairable and recyclable thermosets, but this relatively new technology will require development, including government investment, to reduce risks for its adoption by aerospace and automotive OEMs. The overall goal of the project is to create recyclable carbon fiber composites using vitrimer resins that are more energy efficient to produce and have improved properties over baseline technology. The targeted composites will retain their tensile strength after multiple recycling and reprocessing steps. In addition, monomer will be recoverable through depolymerization and re-usable carbon fibers will be retrieved.

36 MATERIALS SCIENCE↗
DOE OSTI2024

LightMAT: Continous Fiber Malleable Thermoset Composites with sub-1-minute dwell times; validation of impact performance and evaluation of the efficacy of the compression forming process

Recent major advances in polymer chemistry are enabling a paradigm shift in the area of processing and re-processing/recycling of advanced composite materials. Inexpensive compression molding with short cycle times, traditionally available for thermoplastic composites only, are now possible for the thermoset resins based on polyimine chemistry. Participant will collaborate with the LightMAT consortium Labs ORNL, SNL, and PNNL to non-destructively characterize microscopic structural defects (such as voids and resin-rich areas), and perform high speed impact characterization of its malleable thermoset CFRP's. This work is critical to the validation and adoption of these materials for the automotive market and towards DOE-VTO lightweighting mission objectives.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Boroxine based dynamic thermosetting polymers

The disclosure provides for dynamic thermosetting polymers comprising boroxine crosslinks that exhibit unusual mechanical behavior by being strong, highly malleable, recyclable and fully reprocessable. The disclosure further provides methods of making the thermosetting polymers and applications thereof.

Guan, Zhibin↗
DOE OSTI2023

Method of controlled conversion of thermosetting resins and additive manufacturing thereof by selective laser sintering

The invention is directed to a method of controlled conversion of thermosetting resins and additive manufacturing thereof by selective laser sintering. Partial curing of a thermosetting formulation can be used to increase the T g of the resin and minimize the additional cure needed to cross-link a printed object. After printing, the partially cured material is finally cured via a slow temperature ramp maintained just below the material's evolving T g .

Campbell, C. Garrett↗
DOE OSTI2024

Toolpath considerations for extrusion: Pellet, filament, concrete, and thermoset

There are a variety of extrusion and deposition-based processes for additive manufacturing, such as fused deposition modeling (FDM), fused filament fabrication (FFF), and directed energy deposition (DED). These processes can use a variety of materials, including thermoplastic pellets, thermoplastic filament, thermoset, concrete, metal wire, metal powder, and more. For all these processes and materials, the underlying toolpath strategies for 3D-printing an object are the same: the object to be printed is sliced into layers, then the layer is optimally fit with toolpaths of a given width, based on specific user settings. However, based on the specific process being used, additional modifiers and toolpathing strategies may be employed to maximize the capabilities of the process and successfully construct an object. This chapter explores the different pathing considerations and additional strategies to be employed in extrusion processes that use thermoplastics, thermosets, and concretes.

Roschli, Alex↗
DOE OSTI2024

Decomposable and recyclable epoxy thermosetting resins

A thermoset precursor composition includes a backbone comprising an imine bond bonding at least one of: 1) aromatic compounds together, or 2) bonding an aromatic compound to an aliphatic chain, and at least one of: an epoxy group terminating the backbone or an aldehyde group terminating the backbone. The thermoset precursor can have at least two epoxy groups, one epoxy group and one aldehyde group, or two aldehyde groups.

Abu-Omar, Mahdi M.↗
DOE OSTI2025

Initiator‐Driven Tailoring of Reactivity and Inhibition in Frontally Polymerized Dicyclopentadiene‐Co‐Dihydrofuran Thermosets

Incorporating 2,3‐dihydrofuran (DHF) into dicyclopentadiene (DCPD) enables frontally polymerizable, deconstructible thermosets via acid hydrolysis. At 5–20 mol% DHF and low initiator concentration (~100 ppm), DHF inhibits front propagation, lowers the glass transition temperature ( T g ) by up to 20°C, and quenches the front, especially at 20% DHF. This paper demonstrates that increasing the initiator concentration to 250–1000 ppm overcomes inhibition, enhances front speeds by ~50%, and suppresses quenching at the expense of pot‐life. Above 5 mol% DHF, an emergence of a second exotherm is observed, attributed to increased rate dependence on the inhibition of the initiator by DHF. Void formation from volatile DHF is suppressed by applying 110 kPa nitrogen, though at the cost of reduced front speed. Dynamic mechanical analysis shows that higher initiator concentration produced more highly cross‐linked polymers, with a ~20% increase in storage modulus at 25°C and a 20°C increase in T g .

deconstructible thermosets↗
DOE OSTI2023

A facile strategy to fabricate a lignin-based thermoset alternative to formaldehyde-based wood adhesives

The utilization of sustainable lignin to synthesize wood adhesives has attracted increasing attention in recent years. However, the facile fabrication of strong and environmentally friendly lignin-based adhesives with a high lignin content remains a significant challenge. In this study, we developed a formaldehyde-free wood adhesive system by combining alkali lignin and poly(propylene glycol) bis(2-aminopropyl ether). The process of producing lignin-based adhesives involves a simple mixing of wood flour, lignin, and a commercially available crosslinker (polyetherimide), followed by direct hot-pressing into particleboards. The lignin-based adhesive showed a high biomass content of 75 wt% (crosslinker accounting for 25 wt%) and the internal bonding strength of the formaldehyde-free and non-toxic particleboards was 1.42 MPa, outperforming many other bio-based adhesives. In conclusion, the study demonstrates a new and facile strategy to synthesize a lignin-based thermoset that is readily and practically applicable as an adhesive to fabricate high-performance, high lignin content, and formaldehyde-free wood products.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Joining of Thermoset Carbon Fiber Reinforced Polymer and AZ31 Magnesium Alloy Sheet Via Friction Stir Interlocking

A new technique called friction stir interlocking (FSI) was applied for lap-joining of AZ31 magnesium sheet and thermoset carbon fiber reinforced polymer (TS-CFRP) sheet. Instead of directly joining AZ31 and TS-CFRP, a series of magnesium interlocks were used to friction stir weld with AZ31 sheet to enable joining with TS-CFRP. Microstructural characterization of joint cross sections showed that a tool rotation rate of 800 rpm produced incomplete mixing of magnesium interlocks and the top AZ31 sheet, while 1200 rpm achieved sufficient material mixing to avoid unwelded regions. Mechanical property characterization showed that AZ31/TS-CFRP dissimilar joints failed through the magnesium interlock shanks during lap shear tensile testing, with a maximum normalized joint strength reaching ~100 MPa.

Wang, Tianhao↗
DOE OSTI2025

Ensemble cure kinetics network (ECK-Net): A method to derive cure kinetics of thermosetting resin

This paper introduces an Ensemble Cure Kinetics Network (ECK-Net), a neural network (NN)–based framework for modeling the cure kinetics of thermosetting resins within a phenomenological context. ECK-Net replaces traditional analytic models, which require extensive chemical insight and multiple isothermal/non-isothermal experiments, with a data-driven surrogate that maps nonlinear relationships between temperature, degree of cure, and reaction rate from differential scanning calorimetry data. The proposed approach predicts input-dependent kinetic coefficients of a generalized nth-order reaction equation rather than reaction rates directly, enabling a single unified model to represent various epoxy systems without relying on iso-conversional analysis or predefined functional forms. To ensure robustness, multiple independently trained networks under different random initializations are blended through an ensemble strategy, effectively mitigating the stochastic variability inherent to neural networks. The framework is validated using experimental datasets from multiple resin systems, including aerospace-grade materials (Toray 3900-2, Cycom 5320-1, and Hexcel 8552) and a windmill-grade resin (RIMR 035c). The model accurately reproduces the temporal evolution of the degree of cure under manufacturers’ recommended cure cycles across all tested resins systems, yielding Pearson’s correlation coefficients of 0.992, 0.994, 0.993, 0.997, respectively. To demonstrate process-level applicability, the trained network was implemented within the Abaqus environment to simulate out-of-autoclave (OOA) curing process of the CFRP panel composed of Toray T830H-6K/3900-2D prepreg. The simulation results showed excellent agreement with experimental temperature response (maximum peak temperature, simulation: 189.6 °C, experiment: 188.5 °C) and the final degree of cure (simulation: 0.948, experiment: 0.960 ± 0.013), confirming ECK-Net’s capability as a reliable alternative to conventional cure kinetics modeling methods.

Composite curing↗
DOE OSTI2021

Improvement of interfacial adhesion of unidirectional textile grade carbon fiber (TCF) with unsized, epoxy and urethane sizing reinforced in thermoset urethane composites

This work considers a unique wide tow (450k filaments) form of low-cost carbon fiber intended for non-aerospace applications. TCF is currently produced in epoxy and urethane sizing, and there is a need to understand its resulting composite properties. In this work, the interfacial adhesion of sized TCF reinforced in thermoset urethane (TSU) composites are examined through the surface, thermal and mechanical characterization techniques. Atomic force microscopy (AFM) results showed an increase in surface roughness for urethane (276%) and epoxy sized (78%) versus unsized TCF. XPS results showed 531% increase in O in epoxy sized TCF and 250% N content in urethane sized TCF compared to unsized TCF. The surface energy of epoxy and urethane sized TCF is enhanced by 78% and 96%, respectively compared to unsized TCF. The storage modulus showed improvement for urethane (23%) and epoxy (21%) sized than unsized TCF-TSU composites. The flexural, interlaminar shear strength (ILSS), and impact properties of urethane sized TCF increase by 24%, 50%, and 273%, respectively, than unsized TCF. The results demonstrate that the surface and thermal properties correlate with the mechanical properties of TCF-TSU composites and sizing enhances the wettability of the composites.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Accelerated oxidation of epoxy thermosets with increased O 2 pressure

Polymer oxidation is usually accelerated with temperature, which is therefore applied in nearly every experimental approach dealing with predictive materials aging. Because of this simple approach, we may tend to neglect that the effective concentration of oxygen also acts as a rate multiplier for oxidation. Increasing the oxygen partial pressure in an aging environment accelerates oxidation, and while there is often a near proportional increase initially, the effect of additional oxygen usually transitions to a saturation level at some elevated pressure. This has been theoretically described in the general autoxidation scheme and is well recognized. However, for many materials the exact rate behavior under moderately increased oxygen concentration remains to be established. We therefore review epoxy oxidation and offer a broader overview of its behavior under increased O 2 partial pressure. Experimental data are given for a few thermoset materials demonstrating their rate behavior under O 2 partial pressure up to 4 atm, meaning approximately 20 times more than under standard atmospheric conditions. Confirmative evidence suggests that epoxy materials will reach saturation oxidation rates only at significantly higher O 2 partial pressure. In such a high-pressure regime it is theoretically possible to not only accelerate oxidation, but to transition into a condition where O 2 diffusion can be increased without further accelerating the oxidation rate. Finally, this can reduce diffusion limited oxidation effects under specific accelerated aging conditions as a combination of temperature and O 2 partial pressure.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Tribological studies of a novel high-performance aromatic thermosetting copolyester containing carbon nanotubes for artificial hip joints

A high-performance aromatic thermosetting copolyester containing multi-walled carbon nanotubes (ATSP-MWNTs) was synthesized, characterized, and tribologically tested against cobalt-chromium-molybdenum (CoCrMo) alloy) as a potential replacement for ultra-high molecular weight polyethylene (UHMWPE) in artificial joints. By investigating the tribological properties of ATSP-MWNTs, crosslinked UHMWPE vs CoCrMo alloy, it was found that ATSP-MWNTs exhibited a lower and more stable friction coefficient and negligible wear. Further, unlike the case of ATSP-MWNTs, an obvious wear was present for UHMWPE. It is believed that transfer films in ATSP-MWNTs help to stabilize and decrease friction and wear. In addition, large and aggregated particles of UHMWPE seem to contribute to an increase in friction and wear.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2024

Shelf-Stable Bingham Plastic Polyurethane Thermosets for Additive Manufacturing

Here, this study presents an innovative 3D-printing method for fabricating hybrid-hardness polyurethane (PU) thermosets via direct-ink writing (DIW). This method features an unprecedentedly long pot-life of at least 16 months for uncured material, achieved by employing internally-blocked polymeric uredines as the isocyanate source. This innovation not only extends pot life but also broadens the pre-print processing temperature range. Surface-modified fumed silica, used as a rheology modifier, ensures the maintenance of Bingham fluid characteristics. Rigorous evaluations, including DSC, tensile tests, SEM, OM, and μ-CT, verify the material’s uniform and nearly isotropic structure, devoid of defects. DMA analysis reveals that these 3D-printed PUs withstand processing temperatures up to 240°C. The practical application of this technology is demonstrated through the successful 3D printing of a shoe sole, showcasing the ability to incorporate regions of varying hardness, highlighting the versatile property customization of this method.

36 MATERIALS SCIENCE↗