Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “tank testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1947

Tank Tests of a 1/7-Size Dynamic Model of the Grumman XJR2F-1 Amphibian to Determine the Effect of Slotted- and Split-Type Flaps on Take-Off Stability - NACA Model 212, TED No. NACA 2378

Additional tests of a 1/7-size model of the Grumman XJR2F-1 amphibian were made in Langley tank no. 1 to compare the behavior during take-off of the model equipped with split- and slotted-type flaps. The slotted flag had a large effect on locating the forward center-of-gravity limits for stable take-offs. Stable take-offs within the normal operating range of positions of the center of gravity could be made with the split flaps deflected 45deg or with the slotted flaps deflected less than 20deg. At flap deflections required for similar take-off stability, the use of split-flaps resulted lower take-off speeds than the use of slotted flaps. An increase in forward acceleration from 1.1 to 4.8 feet per second per second moved the center-of-gravity limit forward approximately 3-percent mean aerodynamic chord.

Land, Norman S.↗
NASA NTRS1935

Tank Tests of a Model of a Flying-boat Hull Having a Longitudinally Concave Planing Bottom

The NACA model 11-B, which has a longitudinally concave planing bottom forward of the step, was tested over a wide range of loading. The results of the tests are presented as curves of resistance and trimming moment plotted against speed for various trim angles and as curves of resistance coefficient at best trim angle, and trimming-moment coefficient. The characteristics of the form at the optimum trim are compared with those of NACA model 11-C which has the same form with the exception of a planing bottom longitudinally straight near the step. Photographs of the models being towed in the tank are included for a comparison of the spray patterns. At the best angles of trim in each case model 11-B has lower resistance at high speeds, a higher maximum positive trimming moment near the hump speed, and a more favorable spray pattern than of model 11-C.

Parkinson, J B↗
NASA NTRS1981

Tank testing of a 2500-cm2 solar panel

A 50 cm by 50 cm solar array panel test patch was investigated for spacecraft charging and arcing effects. Bombardment with monochromatic electron was carried out. Some objectives of the test were: (1) to estimate at what voltage of electron bombardment arcing would be probable; (2) to find whether the arc's energy would be tolerable or damagingly large; (3) to try and separate thermal and photoeffects; and, (4) to see whether materials used were such as to minimize arcing. Some conclusions were: In sunlight the tracking data relay satellite's solar panel which has ceria glass on the front and conductive paint on the backside is probably a good design for reducing charge-up. In a geomagnetic substorm simulated in testing there will be arcing at the interconnects during eclipse and transitions into and out of eclipse in testing especially in view of the very cold temperatures that will be reached by this lightweight array. Ceria-doped glass is preferred to fused silica glass for reducing charge build up. The Kapton bare patch should still be conductively painted. The differential voltages on the panel determine when arcing first begins, and the electron beam voltages vary depending upon whether the metallic structure is directly grounded or semifloating.

Bever, R. S.↗
NASA NTRS1935

Tank tests of a model of a flying-boat hull with a fluted bottom

A 1/5-scale model of a flying-boat hull having flutes in the bottom both forward and aft of the step (NACA model 19) was tested to determine its water performance. The model was also tested after the successive removal of the flutes on the afterbody and forebody. The results from these tests are compared with those from tests of a model of the hull of the Navy PN-8 flying boat and it is concluded that the fluted-bottom model and its modifications are inferior to the model of the PN-8.

Dawson, John R↗
NASA NTRS1933

A Complete Tank Test of a Model of Flying-boat Hull - N.A.C.A. Model 16

A model of a 2-step flying-boat hull, of the type generally used in England, was tested according to the complete method described in the N.A.C.A. Technical Note No. 464. The lines of this model were taken from offsets given by Mr. William Munro in Flight, May 29, 1931. The data cover the range of loads, speeds, and trim angles that may be of use in applying the hull form to the design of any seaplane. The results are reduced to nondimensional form to aid application to design problems and facilitate comparison with the performance of other hulls. The water characteristics of Model 16 are compared with those of Model 11-A, which is representative of current American practice. The results show that when the two forms are applied to a given seaplane design under optimum conditions for each, the performance of Model 16 will be somewhat inferior to that of Model 11-A.

Shoemaker, James H↗
NASA NTRS1935

Tank Tests of Model 11-G Flying-boat Hull

The NACA model 11-G flying-boat hull, a modification of NACA model 11-A was tested over a range of loadings. The planing bottom of model 11-G has a variable-radius flare, or concavity, at the chines in contrast to the straight V planing bottom of model 11-A. The results are given as curves of resistance and trimming moment plotted against speed for various angles of trim. The characteristics of the form at the optimum angles of trim are given in non-dimensional form as curves of resistance coefficient, best trim angle, and trimming-moment coefficient plotted against speed coefficient. As compared with the original form, model 11-G is shown to have higher resistance at all loads and speeds and higher maximum trimming moments at heavy loads. The spray pattern, however, is generally more favorable, indicating that the service performance of model 11-A would be improved by some form of chime flare.

Parkinson, J B↗
NASA NTRS1934

Tank Tests of Auxiliary Vanes as a Substitute for Planing Area

The results of towing tests made on two models at the request of the Bureau of Aeronautics, Navy Department, are presented. The first model represents the hull of the U.S. Navy PN-8 flying boat, in which the sponsors of the original hull are removed and auxiliary lifting vanes are fitted at the chines immediately forward of the main step. The tests showed that the altered form gave a large increase in hump resistance and a very undesirable spray formation through a large part of the speed range.

Parkinson, John B↗
NASA NTRS1938

Tank Tests of Model 36 Flying Boat Hull

N.A.C.A. Model 36, a hull form with parallel middle body for half the length of the forebody and designed particularly for use with stub wings, was tested according to the general fixed-trim method over the range of practical loads, trims, and speeds. It was also tested free to trim with the center of gravity at two different positions. The results are given in the form of nondimensional coefficients. The resistance at the hump was exceptionally low but, at high planing speeds, afterbody interference made the performance only mediocre.

Allison, John↗
NASA NTRS2024

Performance Testing of Liquid Hydrogen Tanks

Testing the performance of liquid hydrogen in tanks brings many unique challenges. Often methods used even for liquid nitrogen need to be modified to be able to address the details required to fully understand the performance of the tank. During the development and characterization of many novel insulation systems both for in-space and ground applications, NASA has tested many liquid hydrogen tanks where performance was a key outcome. Over the course of analyzing the performance of multiple different hydrogen tests, including several with both hydrogen and nitrogen, differences in the details of test data interpretation become clear. One of these key details is the thermal stratification of the tank and what it can tell you about the heat load dispersion.

Liquid Hydrogen↗
NASA NTRS1975

Development of thermal stratification and destratification scaling concepts. Volume 1: Definition of thermal stratification scaling parameters and experimental investigations

The dimensionless parameters associated with the thermal stratification and pressure history of a heated container of liquid and its vapor were examined. The Modified Grashof number, the Fourier number, and an Interface number were parameterized using a single test liquid, Freon 113. Cylindrical test tanks with spherical dome end caps were built. Blanket heaters covered the tanks and thermocouples monitored the temperatures of the liquid, the ullage, the tank walls, and the foam insulation encapsulating the tank. A centrifuge was used for the 6 inch tank to preserve the same scaling parameter values between it and the larger tanks. Tests were conducted over a range of Gr* values and the degree of scaling was checked by comparing the dimensionless pressures and temperatures for each scaled pair of tests. Results indicate that the bulk liquid temperature, the surface temperature of the liquid, and the tank pressure can be scaled with the three dimensionless parameters. Some deviation was, however, found in the detailed temperature profiles between the scaled pairs of tests.

Lovrich, T. N.↗
NASA NTRS1993

Solar simulator for solar dynamic space power system testing

Planned vacuum tank testing of a solar dynamic space power system requires a solar simulator. Several solar simulators were previously built and used for vacuum tank testing of various space systems. However, the apparent solar subtense angle, i.e., the angular size of the apparent sun as viewed from the experiment, of these solar simulators is too large to enable testing of solar dynamic systems. A new design was developed to satisfy the requirements of the solar dynamic testing. This design provides 1.8 kW/m(sup 2) onto a 4.5M diameter test area from a source that subtends only 1 deg, full cone angle. Key features that enable this improved performance are (1) elimination of the collimating mirror commonly used in solar simulators to transform the diverging beam into a parallel beam; (2) a redesigned lamp module that has increased efficiency; and (3) the use of a segmented reflective surface to combine beams from several individual lamp modules at the pseudosun. Each segment of this reflective surface has complex curvature to control the distribution of light. By developing a new solar simulator design for testing of the solar dynamic system instead of modifying current designs, the initial cost was cut in half, the efficiency was increased by 50 percent reducing the operating costs by one-third, and the volume occupied by the solar simulator was reduced by a factor of 10.

Jefferies, Kent S.↗