Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “strong adhesion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Plasma treatment on both adhesive tape and adherends for significantly enhanced CFRTP-related adhesive joints

Unlike existing literature that primarily concentrates on either the plasma treatment of adherends alone or solely on adhesive surfaces, this work leverages plasma modification of both adhesive in tape form and adherend surfaces to largely enhance the interfacial bonding between a thermoset-based adhesive tape and carbon-fiber-reinforced thermoplastic polymer (CFRTP) for structural bonding applications. Here, by conducting single lap shear tests on adhesively-bonded AA6061-CFRPPA (carbon-fiber-reinforced polyphthalamide) dissimilar joints, it is shown that the plasma treatment of adherends alone can increase the lap shear strength (LSS) of the joints by approximately 200% compared to non-treated counterparts. An additional plasma treatment of adhesive tape surfaces leads to even higher LSS improvement, reaching up to 315%, due to the formation of a denser crosslinked network of covalent bonds and a reduced area fraction of interfacial voids at the CFRPPA/adhesive interface. The highest plasma-enhanced LSS of the metal-CFRTP dissimilar joints rivals that of metal-metal joints, which is typically stronger than the joints associated with fiber-reinforced polymers. This study is important for achieving strong CFRTP-related structural components bonded using adhesive tape, providing better compatibility with plasma treatment and other joining methods like riveting compared to adhesive paste or liquid.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The Bonding Nature and Adhesion of Polyacrylic Acid Coating on Li-Metal for Li Dendrite Prevention

The success of polyacrylic acid (PAA) to suppress Li dendrite growth suggests that the mechanical properties of polymer-based coatings, including the modulus, toughness, and interfacial adhesion are important design criteria. However, the measurement of the adhesion of thin PAA, as well as other polymer coatings to the reactive Li-metal anode surface is limited experimentally and challenging computationally. In this paper, a strategy was proposed to estimate the adhesion and delamination of the PAA(polymer)/Li interface, based on the bonding nature at the simpler PAA (oligomer)/Li interfaces using density functional theory calculations. It has been shown that the carboxylic acid groups in PAA reacted strongly with metallic Li, which significantly enhances the interfacial adhesion through the Li–O bonds formation, Li ionization and its incorporation into PAA, and –H or –OH termination of Li after decomposition of the COOH functional group. During delamination, it was found that the most likely PAA delamination route involved breaking partial Li–O bonds and lifting some ionized Li atoms from the Li-metal, especially for the Li atoms that showed a charge closer to +1 or are bonded with two O atoms from PAA. Based on the average bonding energies from PAA(oligomer)/Li interface delamination calculations, the work of separation, W sep , of the PAA(polymer)/Li interface was estimated to be ~1.0 (J/m 2 ). The high W sep of PAA (polymer)/Li was comparable with the Li 2 O/Li interface and higher than Li 2 CO 3 /Li and LiF/Li interfaces. This order correlated well with the areal density of Li–O bonds, which can serve as a descriptor for the interfacial adhesion. Furthermore, this computational approach can be applied to other interfaces with polymer-based coatings.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Visualization of Aluminum Ions at the Mica Water Interface Links Hydrolysis State-to-Surface Potential and Particle Adhesion

When hydrolyzable cations such as aluminum interact with solid-water interfaces, macroscopic interfacial properties (e.g., surface charge and potential) and interfacial phenomena (e.g., particle adhesion) become tightly linked with the microscopic details of ion adsorption and speciation. We use in situ atomic force microscopy to directly image individual aluminum ions at a mica-water interface and show how adsorbate populations change with pH and aluminum activity. Complementary streaming potential measurements then allow us to build a triple layer model (TLM) that links surface potentials to adsorbate populations, via equilibrium binding constants. Our model predicts that hydrolyzed species dominate the mica-water interface, even when unhydrolyzed species dominate the solution. Ab initio molecular dynamics (AIMD) simulations confirm that aluminum hydrolysis is strongly promoted at the interface. The TLM indicates that hydrolyzed adsorbates are responsible for surface-potential inversions, and we find strong correlations between hydrolyzed adsorbates and particle-adhesion forces, suggesting that these species mediate adhesion by chemical bridging.

Legg, Benjamin A.↗
DOE OSTI2025

Multiple‐Repeated Plasma Surface Treatments for Significantly Improving Bonding Performance of Metal‐Carbon‐Fiber‐Reinforced Thermoplastic Polymer Dissimilar Adhesive Joints

This work investigates how multiple‐repeated plasma surface treatments can significantly enhance adhesively bonded metal‐carbon‐fiber‐reinforced thermoplastic polymer (CFRTP) dissimilar joints, a topic that has been rarely investigated compared to other parameters during the plasma treatment process. By conducting double cantilever beam tests on adhesively bonded AA6061‐carbon‐fiber‐reinforced polyphthalamide (CFRPPA) dissimilar joints, it is shown that the average Mode I specific fracture energy after 20 repetitions of the same plasma treatment, using processing parameters without noticeably changing surface roughness, can be improved and saturated up to almost 2000% compared to non‐treated joints and almost 240% compared to a single plasma treatment commonly used in the literature. The improvement can be attributed to the enhanced chemical bonding at the CFRPPA‐adhesive interface. This study is important for achieving strong bonding performance of CFRTP‐related structural joints using multiple plasma treatments, a simple and effective method.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Rheology and Gelation of Hyaluronic Acid/Chitosan Coacervates

Hyaluronic acid (HA) and chitosan (CHI) are biopolyelectrolytes which are interesting for both the medical and polymer physics communities due to their biocompatibility and semi-flexibility, respectively. In this work, we demonstrate by rheology experiments that the linear viscoelasticity of HA/CHI coacervates depends strongly on the molecular weight of the polymers. Moduli for coacervates were found significantly higher than those of individual HA and CHI physical gels. A remarkable 1.5-fold increase in moduli was noted when catechol-conjugated HA and CHI were used instead. This was attributed to the conversion of coacervates to chemical gels by oxidation of 3,4-dihydroxyphenylalanine (DOPA) groups in HA and CHI to di-DOPA crosslinks. These rheological results put HA/CHI coacervates in the category of strong candidates as injectable tissue scaffolds or medical adhesives.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Interfacial charge transfer and interaction in the MXene/TiO 2 heterostructures

Hybrid materials of MXenes [two-dimensional (2D) carbides and nitrides] and transition-metal oxides have shown great promise in electrical energy storage (EES) and 2D heterostructures have been proposed as the next-generation electrode materials to expand the limits of current technology. Here we use first principles density functional theory to investigate the interfacial structure, energetics, and electronic properties of the heterostructures of MXenes (Ti n+1 C n T 2 ; T = terminal groups) and anatase TiO 2 . We find that the greatest work-function differences are between OH-terminated MXene (1.6 eV) and anatase TiO 2 (101) (6.4 eV), resulting in the largest interfacial electron transfer (~0.9e/nm 2 across the interface) from MXene to the TiO 2 layer. This interface also has the strongest adhesion and is further strengthened by hydrogen bond formation. For O–, F–, or mixed O–/F– terminated Ti n+1 C n MXenes, electron transfer is minimal and interfacial adhesion is weak for their heterostructures with TiO 2 . The strong dependence of the interfacial properties of the MXene/TiO 2 heterostructures on the surface chemistry of the MXenes will be useful to tune the heterostructures for EES applications.

2-dimensinal systems↗
DOE OSTI2025

Electrostatically Enhanced Buried Interface Binding of Self‐Assembled Monolayers for Efficient And Stable Inverted Perovskite Solar Cells

Inverted p‐i‐n structure perovskite solar cells (PSCs) have outperformed traditional n‐i‐p PSCs in recent years. A key advancement is the use of self‐assembled monolayers (SAMs) as hole transport layers. One class of widely used SAMs is carbazole‐based phosphonic acids. However, it is found that these SAMs lack strong binding with transparent conducting oxides (TCO) and perovskite. The weak binding strength results in suboptimal interfacial adhesion of the buried interface, which limits the device's stability. Here, interfacial binding is enhanced by increasing the dipole moment that creates a strong interfacial electric field that enhances electrostatic interactions at the TCO/perovskite interface, while incorporating tailored functional groups in SAMs to improve chemical anchoring to TCO and binding to perovskite. Specifically, the donor‐acceptor SAM molecule 4‐(7‐(4‐(bis(4‐methoxyphenyl)amino)‐2,5‐difluorophenyl)benzo[c][1,2,5]thiadiazol‐4‐yl)benzoic acid (PAFTB) is employed, which features an enhanced dipole moment along with electron‐donating and electron‐withdrawing functional groups to optimize interfacial interactions. Compared to extensively used [2‐(9H‐carbazol‐9‐yl)ethyl]phosphonic acid (2PACz), PAFTB enhances total interfacial adhesion by 2.8 times, thereby improving the thermal stability of the layer. Using this approach, PSCs are demonstrated with a certified quasi‐steady‐state power conversion efficiency of 24.9% and maintain 80% of the initial efficiency after 900 h of maximum power point tracking at 85 °C.

Interfacial adhesion↗
DOE OSTI2024

Differential roles of kinetic on- and off-rates in T-cell receptor signal integration revealed with a modified Fab’-DNA ligand

Antibody-derived T-cell receptor (TCR) agonists are commonly used to activate T cells. While antibodies can trigger TCRs regardless of clonotype, they bypass native T cell signal integration mechanisms that rely on monovalent, membrane-associated, and relatively weakly binding ligand in the context of cellular adhesion. Commonly used antibodies and their derivatives bind much more strongly than native peptide major histocompatibility complex (pMHC) ligands bind their cognate TCRs. Because ligand dwell time is a critical parameter that tightly correlates with physiological function of the TCR signaling system, there is a general need, both in research and therapeutics, for universal TCR ligands with controlled kinetic binding parameters. To this end, we have introduced point mutations into recombinantly expressed α-TCRβ H57 Fab to modulate the dwell time of monovalent Fab binding to TCR. When tethered to a supported lipid bilayer via DNA complementation, these monovalent Fab’-DNA ligands activate T cells with potencies well-correlated with their TCR binding dwell time. Single-molecule tracking studies in live T cells reveal that individual binding events between Fab'-DNA ligands and TCRs elicit local signaling responses closely resembling native pMHC. The unique combination of high on- and off-rates of the H57 R97L mutant enables direct observations of cooperative interplay between ligand binding and TCR-proximal condensation of the linker for activation of T cells, which is not readily visualized with pMHC. This work provides insights into how T cells integrate kinetic information from TCR ligands and introduces a method to develop affinity panels for polyclonal T cells, such as cells from a human patient.

Science & Technology - Other Topics↗
DOE OSTI2026

Triggerable adhesives with infinite working life for large area application

Oak Ridge National Laboratory (ORNL) Manufacturing Demonstration Facility (MDF) entered a User Proposal with Perseus Materials in Knoxville, TN. By reinventing how composites are made, we unlock a new era of structural materials: faster to produce, easier to assemble, and strong enough for real-world scale. Perseus Materials was targeting the wind turbine industry to make large adhesive joints for composite turbine blades without the limitations of cure time and room temperature cure without the needs to have work times. The triggerable aspect would increase manufacturing rates for composite wind turbine blades.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Effect of annealing on the tribological behavior of Zr-based bulk metallic glass

Bulk Metallic Glasses (BMGs) are promising materials for several applications owing to their high elastic limit and resistance to permanent deformation. However, BMGs have lower wear resistance than their crystalline counterparts during dry sliding. The formation of a composite material with crystalline phases dispersed in the BMG matrix through devitrification and partial crystallization at elevated temperatures has recently been proposed as an effective way to improve the wear resistance. However, our understanding of the origin of the improved wear behavior of annealed BMGs is still elusive. Here, a systematic evaluation of the effect of annealing temperature (from temperatures lower than the BMG glass transition temperature to temperatures higher than the BMG recrystallization temperature) on the friction and wear response of a Zr-based BMG, namely Vit105 (Zr 52.5 Cu 17.9 Ni 14.6 Al 10 Ti 5 ), was performed. The results indicate that annealing Vit105 improves its wear resistance while also reducing the steady-state friction response when the annealing temperature is close to the glass transition temperature. Notably, the formation of a transfer film on the sapphire countersurface is highly dependent on the applied normal load and sliding time. Finally, the wear mechanism was found to be strongly dependent on the annealing temperature as a transition from a predominantly adhesive wear mechanism to an abrasive-dominated one was observed as the annealing temperature crossed the glass transition temperature. Altogether, the results of this work aid to our understanding of the tribological behavior of Zr-based BMGs in general, while also providing clues to strategies for the effective use of BMGs in tribological applications.

Lien, Hsu-Ming [Univ. of Texas, Austin, TX (United↗
DOE OSTI2025

How Topological Polymer Loops on the Nanoparticle Surface Control the Mechanical Properties of Nanocomposites

Carbon black (CB) and silica (SiO 2 ) filled elastomers are known to be the most successful polymer nanocomposites (PNCs) in industry, where “bound rubber (BR)” (i.e., polymer chains that are physically or chemically adsorbed on the nanofiller surface) plays a critical role in their reinforcement. Here, we report a molecular-scale mechanism underlying the “BR-induced reinforcement” by integrating neutron scattering experiments and molecular dynamics simulations. Simplified non-cross-linked SiO 2 -filled polybutadiene (PB) and CB-filled PB reveal the critical role of topological polymer loops in the BR for the enhanced mechanical performance. The average loop size on the SiO 2 surface modified with a silane coupling agent is much smaller than that on the CB surface and the loops on the SiO 2 surface are densely formed, preventing interdigitation with the matrix chains. On the other hand, the larger, uncrowded loops formed on the CB surface facilitate the interdigitation with the matrix polymer chains even near the filler surface. In this way, a strong connectivity is established between a matrix and a nanofiller, resulting in an adhesive filler–polymer interface. Furthermore, our findings shed light on rich and complex physics and materials design problems in PNCs, where the topological polymer structure on the nanofiller surface directly controls the macroscopic mechanical properties.

36 MATERIALS SCIENCE↗
DOE OSTI2023

First-principles study of interfaces in Al/SiC metal-matrix composite system

In this work, first-principles calculations were performed on the interfaces between Al and SiC, which is a widely used strengthening agent in aluminum metal-matrix-composites (Al/MMC). C-terminated interfaces have much larger work of adhesion than Si-terminated interfaces, indicating that the former has much stronger interfacial bonding. The electron localization function shows that the chemical bonding between Al and C has a strong covalent character, while the bonding between Al and Si is largely metallic. As a result of the vastly different chemical bonding, the work of adhesion for C-terminated interfaces increases with the number of dangling bonds at the interface, while the opposite trend was observed for Si-terminated interfaces. Additionally, the interface energy for Si-terminated interfaces is comparable to that for C-terminated interfaces, suggesting both types of terminations can coexist in the Al/SiC system.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Leak-tight crack repair for 304L stainless steel using friction surfacing

Here, friction surfacing (FS) was investigated as a method for sealing 50 μm wide thru-cracks in 3-mm-thick 304L stainless steel (304L) plate. Friction surfacing was performed using two sizes of 304L consumable rod, with diameters of 9.52 mm and 12.7 mm, on two substrate conditions (clean and oxidized). Friction surfacing was able to deposit a 600 μm thick coating and repair cracks to a depth of 100 μm - 200 μm below the original surface, when using the 12.7-mm-diameter consumable rod for both substrate conditions. Helium leak rates of 10 -10 atm-cc/s were achieved on crack repairs, designating them as leak-tight by the ANSI N14.5 standard. Optical and scanning electron microscopy were used to investigate the coating microstructure and bond interfaces. In this study, the 12.7-mm-diameter rod performed better with disruption of the oxide layer on the oxidized substrate and providing a more homogenous coating. Mechanical properties of the coated samples were evaluated by performing micro-indentation, tensile, bending, and adhesion testing. Higher hardness in the coatings was observed due to the fine equiaxed grains resulting from dynamic recrystallization. Complete consolidation of plastically deformed material on the substrate and a strong diffusion bond across the interface was observed. This was reflected in tensile and bending properties of the FS coatings being comparable to those of uncoated specimen. No delamination of the FS coating was observed during adhesion testing. The results demonstrate that friction surfacing is a viable option to seal cracks in stainless steels.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Novel Zwitterionic Polyurethane-in-Salt Electrolytes with High Ion Conductivity, Elasticity, and Adhesion for High-Performance Solid-State Lithium Metal Batteries

This study presents a novel polymer-in-salt (PIS) zwitterionic polyurethane-based solid polymer electrolyte (zPU-SPE) that offers high ionic conductivity, strong interaction with electrodes, and excellent mechanical and electrochemical stabilities, making it promising for high-performance all solid-state lithium batteries (ASSLBs). The zPU-SPE exhibits remarkable lithium-ion (Li+) conductivity (3.7 × 10⁻⁴ S cm−1 at 25 °C), enabled by exceptionally high salt loading of up to 90 wt.% (12.6 molar ratio of Li salt to polymer unit) without phase separation. It addresses the limitations of conventional SPEs by combining high ionic conductivity with a Li+ transference number of 0.44, achieved through the incorporation of zwitterionic groups that enhance ion dissociation and transport. The high surface energy (338.4 J m−2) and elasticity ensure excellent adhesion to Li anodes, reducing interfacial resistance and ensuring uniform Li+ flux. When tested in Li||zPU||LiFePO₄ and Li||zPU||S/C cells, the zPU-SPE demonstrated remarkable cycling stability, retaining 76% capacity after 2000 cycles with the LiFePO4 cathode, and achieving 84% capacity retention after 300 cycles with the S/C cathode. Molecular simulations and a range of experimental characterizations confirm the superior structural organization of the zPU matrix, contributing to its outstanding electrochemical performance. The findings strongly suggest that zPU-SPE is a promising candidate for next-generation ASSLBs.

Wang, Kun↗
DOE OSTI2022

Size-Dependent Adsorption and Adhesion Energetics of Ag Nanoparticles on Graphene Films on Ni(111) by Calorimetry

Interest in the use of carbon supports for late transition metal nanoparticle catalysts has expanded rapidly due to the increasing importance of electrocatalysts for clean energy and environmental technologies and the use and storage of renewable electricity. Compared to oxide supports, almost nothing is known about the effect of metal nanoparticle size on the energies of the metal atoms within carbon-supported nanoparticles, yet these energies are crucial for understanding their surface reactivity and sintering kinetics. Here, the growth morphology and adsorption energetics of vapor-deposited Ag onto clean graphene/Ni(111) surfaces have been studied using a combination of single-crystal adsorption calorimetry (SCAC) and He + low-energy ion scattering (LEIS). The differential heat of Ag adsorption is 207 kJ/mol for making ~30 atom Ag particles on graphene terraces at 100 K and 16 kJ/mol higher for making ~9 atom Ag clusters at defect sites at the same temperature. The heat of adsorption increases rapidly with Ag coverage as 3D Ag nanoparticles nucleate and grow in size, asymptotically reaching within 5 kJ/mol of the bulk Ag sublimation enthalpy (285 kJ/mol) by 2 ML. The heats of adsorption and Ag nanoparticle densities from LEIS (~10 16 /m 2 ) were combined to provide the Ag/graphene adhesion energy (E adh = 1.8 J/m 2 in the large-particle limit) and the Ag chemical potential (μ) versus effective particle diameter (D). The Ag chemical potential was well-fitted by μ(D) = (3γ v /M – E adh )(1 + (1.5 nm)/D)(2V m /D), where γ v /M is the surface energy of bulk Ag and V m is its molar volume. The same equation is known to fit similar data for late transition metals on clean surfaces of metal oxide single crystals. The adhesion energy of Ag measured here on graphene falls within the wide range measured for Ag on those oxide surfaces and is almost as large as on the oxide that binds Ag particles most strongly, namely CeO 2 (111), which is well-known to be very effective at resisting catalyst deactivation by metal sintering. Furthermore, these results imply that carbon supports will be effective at resisting sintering and that Ag particles smaller than 6 nm on graphene will bind small adsorbed reaction intermediates more weakly than supports with weaker adhesion to Ag, like MgO(100).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Dual material fused filament fabrication of composite core‐shell structures with improved impact resistance and interfacial adhesion

The mechanical performance of parts produced by fused filament fabrication (FFF) has been limited due to the presence of voids and poor interlayer welding. Recent advancements in FFF have enabled the fabrication of void-free objects with strong interlayer welding through the use of semicrystalline polymer shells such as high-density polyethylene (HDPE) along with a high viscosity core polymer like acrylonitrile-butadiene-styrene (ABS). Furthermore, the zero-shear viscosity (η0) of ABS is three orders of magnitude higher than HDPE making the ABS-HDPE core-shell configuration preferable. ABS holds the shape by preventing bulk flow and part bending while HDPE promotes full surface contact across the layers. Most polymers, however, are immiscible which causes a weak weld line along the core-shell interface. Herein, maleic anhydride (MAH) is grafted to the butadiene segment of the ABS core thereby compatibilizing the interface with HDPE, improving the interfacial adhesion. Attenuated total reflectance-Fourier transform infrared spectroscopy was employed to confirm successful grafting. Using a custom-made die affording the core-shell structure, the ABS-g-MAH is shown to improve the impact resistance by 253% and 16% compared to neat HDPE and ABS specimens, respectively. Additionally, a 10% increase compared to the unmodified ABS-HDPE core-shell configuration is observed.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Corrosion resistant hot melt adhesive to bind metals

Hot melt adhesives (HMAs) play an important role in many industries, and their demand is expected to grow. HMAs don't require any solvents, and their application results in the formation of strong bonds with the substrate upon cooling within seconds. These properties differentiate them from liquid glues and make them preferable for practical application. Currently, commercial HMAs are used in bonding lightweight materials such as paper, polymers, and cartons, and have limited usage in areas necessitating the bonding of heavier objects like metals. Here, in this study, we report a design and testing of versatile platform comprising an ion-coordinating polymer and ionic fillers for performance optimization and understanding of structure–property relationships, enabling the rational design of HMAs with improved adhesion to metal surfaces. All-atom Molecular dynamics (MD) simulations and various characterization methods are used to elucidate the adhesion mechanism in model composite system containing polyethylene oxide mixed with chemically diverse salt particles. The maximum adhesion strength is found in composites with Al(OH) 3 and FeCl 3 fillers. Interestingly, the presence of Al(OH) 3 also provides a multifunctional anticorrosion property as measured electrochemically using the Tafel method. The discovered path to formulations with improved adhesion to metal surfaces constitutes an important step toward advancing HMAs for use in the structural and semi-structural metal work domain.

Adhesive and cohesive forces↗