Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solvent annealing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Plasma deposited silicon nitride for indium phosphide encapsulation

The composition and the annealing characteristics of plasma-deposited silicon-nitride encapsulating films on the ion-implanted InP substrates were investigated, using two different substrate-cleaning procedures (organic solvents and HF or HIO3 solutions) prior to encapsulation. The effect of plasma deposition of silicon nitride on the InP substrates was assessed through the current-voltage characteristics of Schottky diodes. Results of XPS analyses showed that the cleaning procedure that employed HF solution left less oxygen on the InP surface than the procedure involving HIO3. No chemical interaction between the film and the substrate was observed before or after annealing.

Valco, G. J.↗
DOE OSTI2020

Solvent-Mediated Synthesis of Amorphous Li 3 PS 4 /Polyethylene Oxide Composite Solid Electrolytes with High Li + Conductivity

Solvent-mediated routes have emerged as an effective, scalable, and low-temperature method to fabricate sulfide-based solid-state electrolytes. However, tuning the synthesis conditions to optimize the electrolyte’s morphology, structure, and electrochemical properties is still underexplored. Here, we report a new class of composite solid electrolytes (SEs) containing amorphous Li 3 PS 4 synthesized in situ with a poly(ethylene oxide) (PEO) binder using a one-pot, solvent-mediated route. The solvent and thermal processing conditions have a dramatic impact on the Li 3 PS 4 structure. Conducting the synthesis in tetrahydrofuran resulted in crystalline β-Li 3 PS 4 whereas acetonitrile led to amorphous Li 3 PS 4 . Annealing at 140 °C increased the Li + conductivity of an amorphous composite (Li 3 PS 4 + 1 wt % PEO) by 3 orders of magnitude (e.g., from 4.5 × 10 –9 to 8.4 × 10 –6 S/cm at room temperature) because of: (i) removal of coordinated solvent and (ii) rearrangement of the polyanionic network to form P 2 S 7 4– and PS 4 3– moieties. The PEO content in these composites should be limited to 1–5 wt % to ensure reasonable Li+ conductivity (e.g., up to 1.1 × 10 –4 S/cm at 80 °C) while providing enough binder to facilitate scalable processing. Here, the results of this study highlight a new strategy to suppress crystallization in sulfide-based SEs, which has important implications for solid-state batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1986

Polyimides containing oxyethylene units. Part 4: Polymerization of dianhydrides containing ether linkages

The development of new composite resins for various aerospace applications is attempted. Although it is highly desirable that these polymers be soluble in order to facilitate processing, they must display considerable solvent-resistance in use. A recent approach has involved the synthesis of a new series of polyimides containing flexible linkages. The polymers were prepared by the polymerization of aromatic dianhydrides with diamines containing oxyethylene linkages. For example, the polymerization of 3,3',4,4'-benzophenonetetracarboxylic dianhydride (BTDA) with 1,2-bis(4-aminophenoxy)ethane (1a) and bis2-(4-aminophenoxy)ethylether (lb), afforded highly crystalline polyimides that were completely insoluble. However, a polyimide that was amorphous and soluble was obtained from the polymerization of BTDA and an isomer of lb, i.e., bis2-(3-aminophenoxy)ethyl ether (4b). In an attempt to obtain a soluble, amorphous polyimide that could be annealed into a crysalline state, block copolymers of 1b and 4b and BTDA were prepared. Copolymers containing less than 20 weight % 1b were soluble in organic solvents. However, these polymers did not crystallize when heated above their Tg's. Copolymers containing higher levels of 1b were semicrystalline and insoluble. The polymerization of the diamines containing oxyethylene linkages with 4,4'-oxydiphthalic anhydride (ODPA) and a new dianhydride, i.e., 4,4'-oxyethyleneoxyethyleneoxydiphthalic anhydride (OEDA) was investigated. It was postulated that the use of these more flexible dianhydrides would result in more processable polyimides.

Harris, F. W.↗
DOE OSTI2020

Universal and versatile morphology engineering via hot fluorous solvent soaking for organic bulk heterojunction

After explosive growth of efficiency in organic solar cells (OSCs), achieving ideal morphology of bulk heterojunction remains crucial and challenging for advancing OSCs into consumer market. Herein, by utilizing the amphiphobic nature and temperature-dependent miscibility of fluorous solvent, hot fluorous solvent soaking method is developed to optimize the morphology with various donor/acceptor combinations including polymer/small-molecule, all-polymer and all-small-molecule systems. By immersing blend film into hot fluorous solvent which is utilized as liquid medium with better thermal conductivity, the molecular reorganization is accelerated. Furthermore, fluorous solvent can be miscible with the residue of chloroform and chloronaphthalene above upper critical solution temperature. This mixed solvent diffuses around inside the active layer and selectively promotes molecular reorganization, leading to optimized morphology. Compared to widely-used thermal annealing, this approach processed under mild conditions achieves superior photovoltaic performance, indicating the practicality and universality for morphological optimization in OSCs as well as other optoelectronic devices.

14 SOLAR ENERGY↗
DOE OSTI2021

Processing of perovskite films using inks with complexing agents

A method can comprise providing an ink comprising reactants, a complexing agent, and a solvent, depositing the ink onto a substrate to form a wet film, drying the wet film to form a precursor layer, and annealing the precursor layer to form a perovskite film. The reactants can comprise a first and a second cation, a first metal, and a first and a second anion, wherein the first and second cations are different from each other, and the first and second anions are different from each other. The complexing agent can comprise a heterocyclic donor material. The perovskite film can comprise a mixed-cation mixed-halide perovskite material, and less than 5% by mass of the complexing agent. The perovskite film can also be formed using a one-step process.

Bailie, Colin David↗
DOE OSTI2021

Reducing roughness and improving efficiency of MAPbI3 perovskite solar cells made by high-throughput photonic curing

For perovskite solar cells (PSCs) to be commercially viable, the slow and energy-insufficient thermal annealing step must be eliminated. Among the photo-irradiation methods proposed to replace thermal annealing, photonic curing is the fastest conversion method. Photonic curing delivers short (20 μs to 100 ms) but intense light pulses from a broadband (200-1500 nm) xenon flash lamp, making it the only method to convert perovskite under 20 ms. This processing time can be extrapolated to a roll-to-roll web speed of 40 m/min based on laboratory processing conditions. However, most reported PSCs made by photonic curing under 1 second have inferior performance (~10% PCE). Although SEM images show dense and pinhole-free perovskite films, AFM images indicate secondary wavy features of 500 nm-wide ridge and 80 nm-deep trenches on photonically cured perovskite films, the existence of which correlates with poor device performance. We suggest that this morphology feature is produced by volatile solvent evaporation during the fast photonic curing process. Two approaches have been made to remedy this issue: (1) adding CH2I2 as the third solvent in the conventional DMF-DMSO system and (2) applying a controlled air-blowing step before photonic curing to remove excess solvent further. Combining these two approaches produces photonically- cured perovskite films with a comparable film roughness and device performance. Alkyl halide additives have been reported to enhance PSC performance by modulated solvent-solute interactions and C-X (X = Cl, Br, and I) cleavage. Photonic curing can cleave CH2I2, producing disassociated iodide ions to replenish iodine loss induced by photonic curing, which is confirmed by EDX. As a co-solvent, the high boiling point of CH2I2 can also make the solvent less volatile, reducing surface roughness in photonically cured perovskite films. Additionally, photonically-cured perovskite films have longer PL lifetimes and a higher recombination resistance compared to thermally-annealed counterparts. As a result, we demonstrate that photonic curing is a suitable method to replace thermal annealing in high-throughput PSC fabrication.

14 SOLAR ENERGY↗
DOE OSTI2022

Establishing Self-Dopant Design Principles from Structure–Function Relationships in Self-n-Doped Perylene Diimide Organic Semiconductors

Self-doping is a particular doping method that has been applied to a wide range of organic semiconductors. However, there is a lack of understanding regarding the relationship between dopant structure and function. A structurally diverse series of self-n-doped perylene diimides (PDIs) is investigated to study the impact of steric encumbrance, counterion selection, and dopant/PDI tether distance on functional parameters such as doping, stability, morphology, and charge-carrier mobility. The studies show that self-n-doping is best enabled by the use of sterically encumbered ammoniums with short tethers and Lewis basic counterions. Additionally, water is found to inhibit doping, which concludes that thermal degradation is merely a phenomenological feature of certain dopants, and that residual solvent evaporation is the primary driver of thermally activated doping. In situ grazing-incidence wide-angle X-ray scattering studies show that sample annealing increases the π–π stacking distance and shrinks grain boundaries for improved long-range ordering. These features are then correlated to contactless carrier-mobility measurements with time-resolved microwave conductivity before and after thermal annealing. In conclusion, the collective relationships between structural features and functionality are finally used to establish explicit self-n-dopant design principles for the future design of materials with improved functionality.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Solid additive engineering enables high-efficiency and eco-friendly all-polymer solar cells

Currently, morphology optimization of all-polymer solar cells (all-PSCs) strongly depends on the use of solvent additives, which are usually highly toxic and harmful to the environment and human health. Here, we report a green and volatile solid additive, 2-methoxynaphthalene (2-MN). It was found that the incorporation of 2-MN into a PM6:PY-DT blend can effectively manipulate the aggregations of PM6 and PY-DT during film depositing and thermal annealing processes and results in highly ordered molecular packing and favorable phase-separated morphology. Consequently, a record-high efficiency of 17.32% is achieved for the PM6:PY-DT device. Moreover, 2-MN-processed all-PSCs were fabricated by using non-halogenated solvent. High efficiencies of 17.03% and 16.67% are obtained for all-PSCs fabricated under nitrogen atmosphere and ambient conditions, respectively. Finally, our work shows that the utilization of 2-MN as a green and solid additive is a simple and feasible strategy to optimize the morphology and sheds new light on eco-friendly fabrication and application of all-PSCs.

14 SOLAR ENERGY↗
DOE OSTI2025

A reversible solvent segregation transition at grain boundaries in gold-platinum alloys

Solute segregation to grain boundaries in polycrystalline metals and ceramics is a well-known phenomenon that reduces the total energy of the material. In this letter, the segregation of the solvent (Au) to grain boundaries in a binary Au 1-x Pt x (x = 0.15 to 0.18) alloy is demonstrated. After heating in the range of 500 °C to 600 °C and quenching to room temperature, grain boundaries in the alloy are enriched in Au at a mean level of ∼ 4 atoms/nm 2 . When the alloy is annealed at 300 °C and quenched, the mean grain boundary composition is closer to the bulk composition. When the alloy is reheated to 500 °C, the segregation is reestablished, demonstrating that the transformation from the strongly segregated complexion to the weakly segregated complexion is reversible. The driving force for the solvent segregation is likely the lower grain boundary energy of Au in comparison to Pt.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Ultra-Fast Vertical Ordering of Lamellar Block Copolymer Films on Unmodified Substrates

To utilize the full potential of block copolymer (BCP) thin films for use in technological devices ranging from ion conduction membranes, transistors to nanowire array antennas, rapid self- assembly of lamellar block copolymers (l-BCPs) with vertically oriented lamellar domains on a variety of unmodified substrates is needed. l-BCPs have an inherently larger interfacial area for transport compared to their cylindrical counterpart. Our observations demonstrate that the as-cast weakly ordered vertically oriented state of l-BCP films of polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) from directional evaporation of select solvents, act as “seed templates” for their ultra-fast evolution (~30 s) into well-ordered vertically oriented nanostructures, using a thermal gradient-based Cold Zone Annealing (CZA) technique. Furthermore, vertical lamellae are obtained on unmodified substrates, Quartz and Kapton, and the kinetics of l-BCP ordering is much faster by CZA as compared to the isotropic oven annealing. The rapid ordering kinetics of vertical l-BCPs is tested and found applicable to different molecular weights and film thicknesses ranging from 20 nm to 480 nm, which ultimately flip over to their equilibrium parallel morphology at upper limits of annealing times. This rapid ordering strategy for vertical orientation of l-BCPs using roll-to-roll compatible CZA would be highly relevant for fundamental studies of interfacial transport as well as for industrial applications from membranes to nanowires.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Inline Rolling Shear Alignment: Deposition and Long-Range Order of Block Polymer Templates in a Fast, Single-Step Process

We report the first demonstration of a rapid, single-step technique to align block polymer, thin-film nanostructures that is amenable to continuous speeds ≥10 mm/s. This method, termed Inline Rolling Shear Alignment (IRSA), uses an elastomeric roller coupled with an electric hysteresis brake to shear films before the casting solvent fully evaporates, and it can enable high throughput, large-area manufacturing of patterns such as nanowire templates. IRSA is adaptable to various polymer systems including diblock and triblock polymers, and a post-shear annealing step can yield high-quality nanostructures with orientation parameters >0.99 and defect densities as low as 5 defect-pairs/μm 2 . To demonstrate the effectiveness of IRSA, platinum nanowires were produced from this rapid deposition and alignment approach using poly(styrene-b-2-vinylpyridine), followed by open-air, atmospheric-pressure plasma etching. Furthermore, this integrated concept, with 50x faster operation than existing processes, could be leveraged for cost-effective manufacturing of macroscopically aligned nanostructures in roll-to-roll systems.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Cold air quench control of local crystallization environment in fully air-processed carbon-based perovskite solar cells

Carbon-based perovskite solar cells (C-PSCs) present a low-cost route to efficient photovoltaic technology. Gas quenching is an essential process commonly used for solvent extraction in scalable module fabrication using solution processes, but film quality remains highly sensitive to the localized environmental processing temperature, especially during intermediate phase transitions before perovskite film high temperature annealing. In this study, we introduce a cold air quench strategy to precisely control the local crystallization temperature that simultaneously promotes uniform crystallization and facilitates strain relaxation in fully air-processed C-PSCs. It is found that implementing dry air at 10 °C as the quenching gas yields a champion power conversion efficiency (PCE) of 20.52 %, with preferential (110) orientation and reduced, homogenized in-plane strain. This newly developed technique of a cost-effective low temperature air quenching process also enhances carrier lifetime, reduces interface recombination, and improves charge extraction. Furthermore, this work presents cold air quenching as a scalable, economic method to control perovskite crystallization and strain in C-PSC fabrication, advancing the industrial viability of high-performance perovskite modules.

14 SOLAR ENERGY↗
DOE OSTI2022

Influence of voids on the thermal and light stability of perovskite solar cells

The formation of voids in perovskite films close to the buried interface has been reported during film deposition. These voids are thought to limits the efficiency and stability of perovskite solar cells (PSCs). Here, we studied the voids formed during operation in perovskite films that were optimized during the solution deposition process to avoid voids. New voids formed during operation are found to assemble along grain boundaries at the bottom interface, caused by the loss of residual solvent and conversion of amorphous phase to crystalline phase. Unexpectedly, the formation of these voids did not negatively affect the stability of PSCs. Decreasing the amorphous region in perovskites by thermal annealing decreased the positive iodide interstitial density, and improved the light stability of PSCs. The annealed devices maintained 90% of their initial efficiency and light soaking for 1900 hours at open circuit condition under 1-sun illumination at 50°C.

14 SOLAR ENERGY↗
DOE OSTI2023

High-Throughput Automated Exploration of Phase Growth Behaviors in Quasi-2D Formamidinium Metal Halide Perovskites

Quasi-2D metal halide perovskites (MHPs) are an emerging material platform for sustainable functional optoelectronics, but the uncontrollable, broad phase distribution remains a critical challenge for applications. Nevertheless, the basic principles for controlling phases in quasi-2D MHPs remain poorly understood, due to the rapid crystallization kinetics during the conventional thin-film fabrication process. In this work, a high-throughput automated synthesis-characterization-analysis workflow is implemented to accelerate material exploration in formamidinium (FA)-based quasi-2D MHP compositional space, revealing the early-stage phase growth behaviors fundamentally determining the phase distributions. Upon comprehensive exploration with varying synthesis conditions including 2D:3D composition ratios, antisolvent injection rates, and temperatures in an automated synthesis-characterization platform, it is observed that the prominent n = 2 2D phase restricts the growth kinetics of 3D-like phases—α-FAPbI 3 MHPs with spacer-coordinated surface—across the MHP compositions. Thermal annealing is a critical step for proper phase growth, although it can lead to the emergence of unwanted local PbI 2 crystallites. Additionally, fundamental insights into the precursor chemistry associated with spacer-solvent interaction determining the quasi-2D MHP morphologies and microstructures are demonstrated. The high-throughput study provides comprehensive insights into the fundamental principles in quasi-2D MHP phase control, enabling new control of the functionalities in complex materials systems for sustainable device applications.

2D perovskites↗
NASA NTRS2001

Tunable Optical Properties of Metal Nanoparticle Sol-Gel Composites

We demonstrate that the linear and non-linear optical properties of sol-gels containing metal nanoparticles are highly tunable with porosity. Moreover, we extend the technique of immersion spectroscopy to inhomogeneous hosts, such as aerogels, and determine rigorous bounds for the average fractional composition of each component, i.e., the porosity of the aerogel, or equivalently, for these materials, the catalytic dispersion. Sol-gels containing noble metal nanoparticles were fabricated and a significant blue-shift in the surface plasmon resonance (SPR) was observed upon formation of an aerogel, as a result of the decrease in the dielectric constant of the matrix upon supercritical extraction of the solvent. However, as a result of chemical interface damping and aggregation this blue-shift does not strictly obey standard effective medium theories. Mitigation of these complications is achieved by avoiding the use of alcohol and by annealing the samples in a reducing atmosphere.

Smith, David D.↗
DOE OSTI2021

Methods of making non-covalently bonded carbon-titania nanocomposite thin films and applications of the same

In one aspect of the invention, a dye sensitized solar cell has a counter-electrode including carbon-titania nanocomposite thin films made by forming a carbon-based ink; forming a titania (TiO 2 ) solution; blade-coating a mechanical mixture of the carbon-based ink and the titania solution onto a substrate; and annealing the blade-coated substrate at a first temperature for a first period of time to obtain the carbon-based titania nanocomposite thin films. In certain embodiments, the carbon-based titania nanocomposite thin films may include solvent-exfoliated graphene titania (SEG-TiO 2 ) nanocomposite thin films, or single walled carbon nanotube titania (SWCNT-TiO 2 ) nanocomposite thin films.

Liang, Yu Teng↗
DOE OSTI2023

Carbon-titania nanocomposite thin films and applications of the same

In one aspect of the invention, a dye sensitized solar cell has a counter-electrode including carbon-titania nanocomposite thin films made by forming a carbon-based ink; forming a titania (TiO 2 ) solution; blade-coating a mechanical mixture of the carbon-based ink and the titania solution onto a substrate; and annealing the blade-coated substrate at a first temperature for a first period of time to obtain the carbon-based titania nanocomposite thin films. In certain embodiments, the carbon-based titania nanocomposite thin films may include solvent-exfoliated graphene titania (SEG-TiO 2 ) nanocomposite thin films, or single walled carbon nanotube titania (SWCNT-TiO 2 ) nanocomposite thin films.

Liang, Yu Teng↗
DOE OSTI2024

Carbon-titania nanocomposite thin films and applications of the same

In one aspect of the invention, a dye sensitized solar cell has a counter-electrode including carbon-titania nanocomposite thin films made by forming a carbon-based ink; forming a titania (TiO 2 ) solution; blade-coating a mechanical mixture of the carbon-based ink and the titania solution onto a substrate; and annealing the blade-coated substrate at a first temperature for a first period of time to obtain the carbon-based titania nanocomposite thin films. In certain embodiments, the carbon-based titania nanocomposite thin films may include solvent-exfoliated graphene titania (SEG-TiO 2 ) nanocomposite thin films, or single walled carbon nanotube titania (SWCNT-TiO 2 ) nanocomposite thin films.

Liang, Yu Teng↗