Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “solid electrolytes”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Phase Field Modeling of Pressure Induced Densification in Solid Electrolytes

Adoption of dense and homogeneous solid electrolytes can possibly mitigate the propagation of lithium dendrites and enable lithium metal anodes. Application of external pressure helps to minimize the sintering temperature in oxide ceramics and can potentially densify softer sulfide electrolytes even under room temperature conditions. Here, a previously developed phase field-based computational scheme for predicting the high-temperature sintering-induced densification of oxide ceramic solid electrolytes is extended in the present context to capture the influence of external pressure for densifying solid electrolytes. Two different bulk deformation mechanisms, namely, "reorganization" and "creep deformation," are dominant under external pressure, which is different from the surface and grain-boundary diffusion-induced densification of solid electrolytes that occurs during high temperature sintering. External pressure also increases the points of contact between the particles, which further enhances the propensity of diffusion-induced sintering process. Results obtained from simulations indicate that densification under external pressure is independent of the solid electrolyte particle morphology. Finally, a phase map is generated between applied pressure and temperature for achieving complete densification of oxide ceramics, which can possibly guide the synthesis of thin and dense solid electrolyte separators.

25 ENERGY STORAGE↗
DOE OSTI2021

Materials design of sodium chloride solid electrolytes Na3MCl6 for all-solid-state sodium-ion batteries

All-solid-state sodium-ion batteries have attracted increasing attention owing to the low cost of sodium and the enhanced safety compared to conventional Li-ion batteries. Recently, halides have been considered as promising solid electrolytes (SEs) due to their favorable combination of high ionic conductivity and chemical stability against high-voltage cathode materials. Although a wide variety of lithium chloride SEs, Li 3 MCl 6 , have been developed for high-voltage all-solid-state batteries, only a limited number of sodium chloride SEs have been reported. This study aims to offer a material design insight for the development of sodium chloride SEs through systematic assessment of the phase stability, electrochemical stability, and transport properties of novel Na 3 MCl 6 SEs. Structural calculations indicate that Na 3 MCl 6 exhibits trigonal $P\bar{3}$1c, monoclinic P2 1 /n, and trigonal $R\bar{3}$ phases, and the stable phase of Na 3 MCl 6 is dependent on the type and ionic radius of M. Na 3 MCl 6 typically exhibits a high oxidation potential, demonstrating good electrochemical stability against cathodes. The bond-valence site energy and ab initio molecular dynamics calculations revealed that Na 3 MCl 6 with P2 1 /n and $R\bar{3}$ phases showed low ionic conductivity, while the $P\bar{3}$1c phase slightly improved the ionic conductivity of Na 3 MCl 6 . The formation of Na vacancies by aliovalent substitution considerably increased the ionic conductivity up to four orders of magnitude for pristine Na 3 MCl 6 , exhibiting ~10 –5 S cm –1 for trigonal $P\bar{3}$1c and $R\bar{3}$ phases. The formation of defects could further enhance the ionic conductivity of Na 3 MCl 6 , and the optimization of defect type and ratio can be helpful in developing superionic Na chloride SEs. The material design of Na 3 MCl 6 in this study will provide fundamental guidelines for the development of novel sodium halide SEs for all-solid-state sodium-ion batteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Phase-Transition Interlayer Enables High-Performance Solid-State Sodium Batteries with Sulfide Solid Electrolyte

All-solid-state sodium (Na) batteries (ASSSBs) using sulfide-based solid electrolytes (SEs) have attracted intensive attention due to their superior safety, high energy density and low cost. However, interfacial issue is one of the biggest challenges to achieve high-performance sulfide-based ASSSBs due to the serious reactions between active Na metal and sulfide SEs at the interface. To address the interfacial challenges, we propose in this paper a simple and efficient approach by introducing a polymer electrolyte as an interlayer to stabilize the interface. Na 3 SbS 4 as a model sulfide SE is used to demonstrate the interlayer strategy to stabilize the interface by preventing the detrimental reactions and inhibiting Na dendrites. As a result, stable Na plating/stripping was observed in Na symmetric cells under the current density of 0.1 mA cm –2 . Moreover, ASSSBs with Na metal and TiS 2 electrode delivered long-term stability over 300 cycles remaining a specific capacity above 100 mAh g –1 , and FeS 2 ||Na cells exhibited an impressive specific capacity of up to 200 mAh g –1 after the 20th cycles. This work demonstrates an efficient strategy to address interfacial challenges between sulfide SEs and Na metal, which contributes to the development of ASSSBs in next-generation energy storage systems.

25 ENERGY STORAGE↗
DOE OSTI2021

Dynamics of Emim + in [Emim][TFSI]/LiTFSI Solutions as Bulk and under Confinement in a Quasi-liquid Solid Electrolyte

Quasi-liquid solid electrolytes are a promising alternative for next-generation Li batteries. Furthermore, these systems combine the safety of solid electrolytes with the desired properties of liquids and are typically formed by solutions of Li salts in ionic liquids incorporated into solid matrices. Here, we present a fundamental understanding of the transport properties in solutions of lithium bis(trifluoromethanesulfonyl)imide (LiTFSI) in 1-ethyl-3-methylimidazolium bis(trifluoromethylsulfonyl)imide ([Emim][TFSI]), either in bulk form or incorporated in a boron nitride (BN) matrix. We performed a series of quasi-elastic neutron scattering experiments that, given the high incoherent neutron scattering cross section of hydrogen, allowed us to focus on the Emim + dynamics. First, [Emim][TFSI]/LiTFSI solutions (0.5 and 2.5 mol·kg –1 ) were investigated and we show how the increase in the concentration reduces the Emim+ mobility and increases the activation energy of their long-range motions. Then, the 0.5 mol·kg –1 solution was incorporated into the BN matrix and we report that the diffusivities of the Emim + cations that remain mobile under confinement are highly accelerated in comparison with the bulk sample and the activation energy of these motions is drastically reduced. We present the experimental evidence that this effect is related to the content of the Emim+ cations immobilized near the surfaces of the BN pores.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Dimolybdenum Paddlewheel Complexes with Cation Binding Sites as Electrolyte Additives to Manipulate the Solid-Electrolyte Interphase at Lithium Metal Anodes

The use of electrolyte additives at millimolar loadings to control the surface chemistry of lithium metal anodes (LMAs) is a leading strategy to improve lithium metal batteries and promote electrosynthetic reactions. Whereas previous studies employed either inorganic or organic additives, in this study, we report the first organometallic additive, Mo 2 (mea) 4 [1, mea = 2-(2-methoxyethoxy)acetate], a dimolybdenum paddlewheel complex that is stable under Li plating conditions and features cation binding sites in the second coordination sphere that promote reversible Li + coordination. Binding of Li + ions to 1 induces immobilization of cationically charged aggregates (or products thereof) into the solid electrolyte interphase (SEI), imparting multiple beneficial functions. The modified SEI was found to protect the LMA against parasitic side reactions, produce modest but measurable improvements to Li plating properties (e.g., overpotential, surface structure, and Coulombic efficiency), and improve interfacial charge transport properties. Furthermore, the most notable benefit to battery cycling performance appears in calendar aging tests, which show that the presence of the additive protects the LMA from parasitic side reactions that would otherwise decrease overall cell cycling efficiency over time. Collectively, these data disclose a tactic for designing electrolyte additives using principles of organometallic synthesis.

Additives↗
DOE OSTI2024

Effect of solid-electrolyte pellet density on failure of solid-state batteries

Abstract Despite the potentially higher energy density and improved safety of solid-state batteries (SSBs) relative to Li-ion batteries, failure due to Li-filament penetration of the solid electrolyte and subsequent short circuit remains a critical issue. Herein, we show that Li-filament growth is suppressed in solid-electrolyte pellets with a relative density beyond ~95%. Below this threshold value, however, the battery shorts more easily as the density increases due to faster Li-filament growth within the percolating pores in the pellet. The microstructural properties (e.g., pore size, connectivity, porosity, and tortuosity) of $$75\%{{{{{\rm{L}}}}}}{{{{{{\rm{i}}}}}}}_{2}{{{{{\rm{S}}}}}}-25\%{{{{{{\rm{P}}}}}}}_{2}{{{{{{\rm{S}}}}}}}_{5}$$ 75 % L i 2 S − 25 % P 2 S 5 with various relative densities are quantified using focused ion beam–scanning electron microscopy tomography and permeability tests. Furthermore, modeling results provide details on the Li-filament growth inside pores ranging from 0.2 to 2 μm in size. Our findings improve the understanding of the failure modes of SSBs and provide guidelines for the design of dendrite-free SSBs.

25 ENERGY STORAGE↗
DOE OSTI2021

Working Principle of an Ionic Liquid Interlayer During Pressureless Lithium Stripping on Li 6.25 Al 0.25 La 3 Zr 2 O 12 (LLZO) Garnet‐Type Solid Electrolyte

Abstract Solid‐state‐batteries employing lithium metal anodes promise high theoretical energy and power densities. However, morphological instability occurring at the lithium/solid–electrolyte interface when stripping and plating lithium during cell cycling needs to be mitigated. Vacancy diffusion in lithium metal is not sufficiently fast to prevent pore formation at the interface above a certain current density during stripping. Applied pressure of several MPa can prevent pore formation, but this is not conducive to practical application. This work investigates the concept of ionic liquids as “self‐adjusting” interlayers to compensate morphological changes of the lithium anode while avoiding the use of external pressure. A clear improvement of the lithium dissolution process is observed as it is possible to continuously strip more than 70 μm lithium (i. e., 15 mAh cm −2 charge) without the need for external pressure during assembly and electrochemical testing of the system. The impedance of the investigated electrodes is analyzed in detail, and contributions of the different interfaces are evaluated. The conclusions are corroborated with morphology studies using cryo‐FIB‐SEM and chemical analysis using XPS. This improves the understanding of the impedance response and lithium stripping in electrodes employing liquid interlayers, acting as a stepping‐stone for future optimization.

Fuchs, Till↗
DOE OSTI2022

High areal capacity, long cycle life 4 V ceramic all-solid-state Li-ion batteries enabled by chloride solid electrolytes

All-solid-state Li batteries (ASSBs) employing inorganic solid electrolytes offer improved safety and are exciting candidates for next-generation energy storage. Herein, we report a family of lithium mixed-metal chlorospinels, Li 2 In x Sc 0.666-x Cl 4 (0 ≤ x ≤ 0.666), with high ionic conductivity (up to 2.0 mS cm -1 ) owing to a highly disordered Li-ion distribution, and low electronic conductivity (4.7 × 10-10 S cm -1 ), which are implemented for high-performance ASSBs. Owing to the excellent interfacial stability of the SE against uncoated high-voltage cathode materials, ASSBs utilizing LiCoO 2 or LiNi 0.85 Co 0.1 Mn 0.05 O 2 exhibit superior rate capability and long-term cycling (up to 4.8 V versus Li+/Li) compared to state-of-the-art ASSBs. In particular, the ASSB with LiNi 0.85 Co 0.1 Mn 0.05 O 2 exhibits a long life of >3,000 cycles with 80% capacity retention at room temperature. Additionally, high cathode loadings are also demonstrated in ASSBs with stable capacity retention of >4 mAh cm -2 (~190 mAh g -1 ).

25 ENERGY STORAGE↗
DOE OSTI2024

Electro-Chemo-Mechanical Evolution at the Garnet Solid Electrolyte–Cathode Interface

Solid-state batteries promise higher energy density and improved safety compared with lithium-ion batteries. However, electro-chemomechanical instabilities at the solid electrolyte interface with the cathode and the anode hinder their large scale implementation. Here, in this study, we focus on resolving electro-chemo-mechanical instability mechanisms and their onset conditions between a state-of-the-art cathode, LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622), and the garnet Li 7 La 3 Zr 2 O 12 (LLZO) solid electrolyte. We used thin-film NMC622 on LLZO pellets to place the interfacial region within the detection depth of the X-ray characterization techniques. The experimental probes of the near-interface region included in operando X-ray absorption spectroscopy and ex situ focused ion beam scanning electron microscopy. Electrochemical degradation was not observable during cycling at room temperature with 4.3 V versus Li/Li + charge voltage cutoff, or with stepwise potentiostatic hold up to 4.1 V versus Li/Li + . In contrast, secondary phases including reduced transition metal species (Ni 2+ , Co 2+ ) were found after cycling up to 4.3 V versus Li/Li + at 80 °C and during potentiostatic hold at 4.3 V versus Li/Li + (Ni 2+ ). Intergranular cracks between NMC622 grains and delamination at the NMC622|LLZO interface occurred readily after the first charge. These interface reaction products and mechanical failure lowered the capacity and cell efficiency due to partial loss of the NMC622 phase, partial loss of contact at the interface, and a higher polarization resistance. Electrochemical instability between delithiated NMC622 and LLZO could be mitigated by using a low charge voltage cutoff or cycling at lower temperature. Ways to engineer the mechanical properties to avoid crack deflection and delamination at the interface are also discussed for enhancing mechanical stability.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Stress engineering for crack and dendrite prevention in solid electrolytes via ion implantation

Solid-state batteries represent a promising technology that offers safer and more densely packed energy storage. A primary cause of failure in solid-state cells is the penetration of metal dendrites through the solid electrolyte. Here, we report that fluorine-ion implantation can enhance the mechanical resistance of solid electrolyte Li 6.5 La 3 Zr 1.5 Ta 0.5 O 12 to dendrite propagation by inducing residual compressive stress in the subsurface of the electrolyte. Ion implantation modifies subsurface residual stress and also alters the electrolyte’s surface, resulting in multifunctional enhancement. The combined chemical and mechanical effects of ion implantation enable reversible lithium metal stripping and plating at elevated current densities while enhancing air stability and mitigating the formation of a harmful carbonate layer at the surface. This study provides new insights into a scalable dendrite-suppression strategy for designing solid-state batteries suitable for cycling at room temperature and low stack pressures.

25 ENERGY STORAGE↗
DOE OSTI2021

Computation-guided discovery of coating materials to stabilize the interface between lithium garnet solid electrolyte and high-energy cathodes for all-solid-state lithium batteries

All-solid-state batteries with a lithium metal anode, enabled by lithium garnet solid electrolytes such as Li 7 La 3 Zr 2 O 12 (LLZO), are a promising next-generation energy-storage technology. The further development of all-solid-state battery requires the integration of high-energy cathodes such as LiNi 1-x-y Mn x Co y O 2 (NMC) with the garnet solid electrolyte with stable and low-resistance interfaces, which requires a coating layer to stabilize the interface during high-temperature sintering and electrochemical cycling. In order to guide the future development of interfacial coatings, we perform high-throughput thermodynamic analyses based on first-principles computation to investigate the stability of LLZO garnet and high-energy NMC cathodes with a wide range of materials chemistries. Here our study reveals the factors governing the materials stability with LLZO garnet and NMC cathodes, and identifies the mechanisms of good coating layers stable with LLZO and NMC. In addition to classifying known coating layers, our study provides detailed guiding charts and multiple new materials systems as promising coatings for stabilizing LLZO—NMC interfaces to enable high-energy-density garnet-based all-solid-state batteries. Our demonstrated computation scheme and high-throughput analyses are generally applicable to investigate and screen coating materials for stabilizing interfaces in energy-related applications.

25 ENERGY STORAGE↗
DOE OSTI2021

Al 2 O 3 Thin Films on Magnesium: Assessing the Impact of an Artificial Solid Electrolyte Interphase

Among the many emerging technologies under investigation as alternatives to the successful Lithium-ion battery, the magnesium battery is promising due to the wide availability of magnesium, its high volumetric capacity, and the possibility for safety improvements. One of the largest challenges facing rechargeable magnesium batteries is the formation of a passivation layer at the Mg metal anode interface when reactive species in the electrolyte are reduced at the electrode-electrolyte interface. To control the solid electrolyte interphase in Lithium batteries, protective layers called artificial solid electrolyte interphase (ASEI) layers have been successful in improving Li metal anode performance. The approach of protecting Mg metal anodes from electrolyte degradation has been demonstrated by fewer studies in the literature than Li systems. In this work, we discuss the properties of Al 2 O 3 thin films deposited using atomic layer deposition as an artificial solid electrolyte interphase at the Mg anode. Our results demonstrate that Al 2 O 3 does prevent electrolyte degradation due to the reductive nature of Mg. However, undesirable properties such as defects and layer breakdown lead to Mg growth that causes soft-shorting. The soft-shorting occurs with and without the protection layer, indicating the ALD layer does not prevent it and hinders Al 2 O 3 from being an ideal candidate for a protection layer. Crucial effects of this layer on Mg electrochemistry at the interface were observed, including growth of Mg deposits leading to soft-shorting of the cell whose morphology showed a dependence on the Al 2 O 3 layer. These results may provide guidelines for the future design and development of protective ASEI layers for Mg anodes.

25 ENERGY STORAGE↗
DOE OSTI2021

In situ formation of polymer-inorganic solid-electrolyte interphase for stable polymeric solid-state lithium-metal batteries

Composite polymer electrolytes (CPEs) for solid-state Li-metal batteries (SSLBs) still suffer from gradually increased interface resistance and unconstrained Li-dendrite growth. Herein, we addressed the challenges by designing a LiF-rich inorganic solid-electrolyte interphase (SEI) through introducing a fluoride-salt-concentrated interlayer on CPE film. The rigid but flexible CPE helps accommodate the volume change of electrodes, while the polymeric highly concentrated electrolyte (PHCE) surface-layer regulates Li-ion flux due to the formation of a stable LiF-rich SEI via anion reduction. The designed CPE-PHCE presents enhanced ionic conductivity and high oxidation stability of >5.0 V (versus Li/Li + ). Furthermore, it dramatically reduces the interfacial resistance and achieves a high critical current density of 4.5 mA cm –2 . The SSLBs, fabricated with thin CPE-PHCE membranes (<100 μm) and Co-free LiNiO 2 cathodes, exhibit exceptional electrochemical performance and long cycling stability. Lastly, this approach of SEI design can also be applied to other types of batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Mitigating Interfacial Mismatch between Lithium Metal and Garnet-Type Solid Electrolyte by Depositing Metal Nitride Lithiophilic Interlayer

Solid-state lithium batteries are generally considered as the next-generation battery technology that benefits from inherent nonflammable solid electrolytes and safe harnessing of high-capacity lithium metal. Among various solid-electrolyte candidates, cubic garnet-type Li 7 La 3 Zr 2 O 12 ceramics hold superiority due to their high ionic conductivity (10 –3 to 10 –4 S cm -1 ) and good chemical stability against lithium metal. However, practical deployment of solid-state batteries based on such garnet-type materials has been constrained by poor interfacing between lithium and garnet that displays high impedance and uneven current distribution. Herein, we propose a facile and effective strategy to significantly reduce this interfacial mismatch by modifying the surface of such garnet-type solid electrolyte with a thin layer of silicon nitride (Si 3 N 4 ). This interfacial layer ensures an intimate contact with lithium due to its lithiophilic nature and formation of an intermediate lithium–metal alloy. The interfacial resistance experiences an exponential drop from 1197 to 84.5 Ω cm 2 . Lithium symmetrical cells with Si 3 N 4 -modified garnet exhibited low overpotential and long-term stable plating/stripping cycles at room temperature compared to bare garnet. Furthermore, a hybrid solid-state battery with Si 3 N 4 -modified garnet sandwiched between lithium metal anode and LiFePO 4 cathode was demonstrated to operate with high cycling efficiency, excellent rate capability, and good electrochemical stability. This work represents a significant advancement toward use of garnet solid electrolytes in lithium metal batteries for the next-generation energy storage devices.

25 ENERGY STORAGE↗
DOE OSTI2021

Investigation of glass-ceramic lithium thiophosphate solid electrolytes using NMR and neutron scattering

Solid-state Li batteries require solid electrolytes which have high Li+ conductivity and good chemical/mechanical compatibility with Li metal anodes and high energy cathodes. Structure/function correlations which relate local bonding to macroscopic properties are needed to guide development of new solid electrolyte materials. This study combines diffraction measurements with solid-state nuclear magnetic resonance spectroscopy (ssNMR) and neutron pair distribution function (nPDF) analysis to probe the short-range vs. long-range structure of glass-ceramic Li 3 PS 4 -based solid electrolytes. Here, we demonstrate how different synthesis conditions (e.g., solvent selection and thermal processing) affect the resulting polyanionic network. More specifically, structures with high P coordination numbers (e.g., PS 4 3– and P 2 S 7 4– ) correlate with higher Li + mobility compared to other polyanions (e.g., (PS 3 ) n n– chains and P 2 S 6 4– ). Overall, this work demonstrates how ssNMR and nPDF can be used to draw key structure/function correlations for solid-state superionic conductors.

36 MATERIALS SCIENCE↗
DOE OSTI2020

The Role of Local Inhomogeneities on Dendrite Growth in LLZO-Based Solid Electrolytes

The majority of the ceramic solid electrolytes (LLZO, LATP) demonstrate polycrystalline grain/grain-boundary (G/GB) microstructure. Higher lithium (Li) concentration and lower mechanical stiffness result in current focusing at the GBs. Growth of Li dendrites through local inhomogeneities and subsequent short circuit of the cell is a major concern. Recent studies have revealed that bulk Li metal is a viscoplastic material that has low (~0.3 MPa) and high (~1.0 MPa) yield strength during deformation at smaller and larger rates of strain, respectively. It has been argued that during deposition at smaller current densities, due to its lower yield strength, Li metal should demonstrate plastic flow against stiff ceramic electrolytes, and Li dendrites will be prevented from penetrating through solid electrolytes. In this manuscript, a multiscale modeling framework has been developed for predicting properties of GBs and the bulk of ceramic electrolytes using atomistic calculations for input to mesoscale models. Using the parameters obtained from the atomistic simulations, the mesoscale model reveals that, given enough time, even at low charge rates, lithium dendrites can grow through the GBs of LLZO. The present multiscale model results also provide information regarding the dendrite growth velocity through LLZO.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Multi-mechanistic Strategies for Novel Solid Electrolytes with Superior Properties

Despite a wide range of solid electrolyte phases, most of them only exist at high temperatures. The challenge is to tailor the chemical compositions of solid electrolyte materials that yield high ionic conductivities and low activation energies at ambient temperature. This is crucial for the development of all-solid-state batteries that are both powerful and safe. Here, we report our recent works to meet this challenge by utilizing multiple mechanistic principles and clusters as the building blocks. We show that the atomic-level interactions that govern the fast-ion conduction can be optimized by incorporating polyanion dynamics, non-stoichiometry, point defects and strong ionic correlations. Specifically, two case studies of Li/Na solid electrolytes will be covered, including lithium solid electrolytes (SE) with record-high ionic conductivities at room temperature (over 100 mS/cm) and sodium SE with record-low activation energies (< 0.1 eV).

Fang, Hong↗