Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “separator modification”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2008

Safety Modification of Cam-and-Groove Hose Coupling

A modification has been made in the mating halves of a cam-and-groove hose coupling to prevent rapid separation of the halves in the event that the cam levers are released while the fluid in the hose is pressurized. The need for this modification arises because commercial off-the-shelf cam-and-groove hose-coupling halves do not incorporate safety features to prevent separation in the pressurized state. Especially when the pressurized fluid is compressible (e.g., steam or compressed air), the separated halves can be propelled with considerable energy, causing personal injury and/or property damage. Therefore, one purpose served by the modification is to provide for venting to release compressive energy in a contained and safe manner while preventing personal injury and/or property damage. Another purpose served by the modification, during the process of connecting the coupling halves, is to ensure that the coupling halves are properly aligned before the cam levers can be locked into position.

Schwindt, Paul↗
NASA NTRS2017

Relating a Jet-Surface Interaction Experiment to a Commercial Supersonic Transport Aircraft Using Numerical Simulations

Reynolds-Averaged Navier-Stokes (RANS) simulations were performed for a commercial supersonic transport aircraft concept and experimental hardware models designed to represent the installed propulsion system of the conceptual aircraft in an upcoming test campaign. The purpose of the experiment is to determine the effects of jet-surface interactions from supersonic aircraft on airport community noise. RANS simulations of the commercial supersonic transport aircraft concept were performed to relate the representative experimental hardware to the actual aircraft. RANS screening simulations were performed on the proposed test hardware to verify that it would be free from potential rig noise and to predict the aerodynamic forces on the model hardware to assist with structural design. The simulations showed a large region of separated flow formed in a junction region of one of the experimental configurations. This was dissimilar with simulations of the aircraft and could invalidate the noise measurements. This configuration was modified and a subsequent RANS simulation showed that the size of the flow separation was greatly reduced. The aerodynamic forces found on the experimental models were found to be relatively small when compared to the expected loads from the model’s own weight.Reynolds-Averaged Navier-Stokes (RANS) simulations were completed for two configurations of a three-stream inverted velocity profile (IVP) nozzle and a baseline single-stream round nozzle (mixed-flow equivalent conditions). For the Sideline and Cutback flow conditions, while the IVP nozzles did not reduce the peak turbulent kinetic energy on the lower side of the jet plume, the IVP nozzles did significantly reduce the size of the region of peak turbulent kinetic energy when compared to the jet plume of the baseline nozzle cases. The IVP nozzle at Sideline conditions did suffer a region of separated flow from the inner stream nozzle splitter that did produce an intense, but small, region of turbulent kinetic energy in the vicinity of the nozzle exit. When viewed with the understanding that jet noise is directly related to turbulent kinetic energy, these IVP nozzle simulations show the potential to reduce noise to observers located below the nozzle. However, these RANS simulations also show that some modifications may be needed to prevent the small region of separated flow-induced turbulent kinetic energy from the inner stream nozzle splitter at Sideline conditions.

Reynolds-Averaged Navier Stokes↗
NASA NTRS1988

Assembly Test Article (ATA)

The assembly test article (ATA) consisted of two live loaded redesigned solid rocket motor (RSRM) segments which were assembled and disassembled to simulate the actual flight segment stacking process. The test assembly joint was flight RSRM design, which included the J-joint insulation design and metal capture feature. The ATA test was performed mid-November through 24 December 1987, at Kennedy Space Center (KSC), Florida. The purpose of the test was: certification that vertical RSRM segment mating and separation could be accomplished without any damage; verification and modification of the procedures in the segment stacking/destacking documents; and certification of various GSE to be used for flight assembly and inspection. The RSRM vertical segment assembly/disassembly is possible without any damage to the insulation, metal parts, or seals. The insulation J-joint contact area was very close to the predicted values. Numerous deviations and changes to the planning documents were made to ensure the flight segments are effectively and correctly stacked. Various GSE were also certified for use on flight segments, and are discussed in detail.

Ricks, Glen A.↗
NASA NTRS1996

Ground Based Lidar Characterization of Cirrus Clouds

This paper presents cirrus cloud observations made with the High Spectral Resolution Lidar (HSRL) and the Volume Imaging Lidar (VIL). The HSRL was redesigned to use an iodine absorption filter in place of the Fabry-Perot etalon that was used for spectral separation of the aerosol and molecular lidar returns. These modifications, which improve both sensitivity and calibration stability, are described.

Eloranta, Edwin W.↗
NASA NTRS2003

Cell separation using electric fields

The present invention involves methods and devices which enable discrete objects having a conducting inner core, surrounded by a dielectric membrane to be selectively inactivated by electric fields via irreversible breakdown of their dielectric membrane. One important application of the invention is in the selection, purification, and/or purging of desired or undesired biological cells from cell suspensions. According to the invention, electric fields can be utilized to selectively inactivate and render non-viable particular subpopulations of cells in a suspension, while not adversely affecting other desired subpopulations. According to the inventive methods, the cells can be selected on the basis of intrinsic or induced differences in a characteristic electroporation threshold, which can depend, for example, on a difference in cell size and/or critical dielectric membrane breakdown voltage. The invention enables effective cell separation without the need to employ undesirable exogenous agents, such as toxins or antibodies. The inventive method also enables relatively rapid cell separation involving a relatively low degree of trauma or modification to the selected, desired cells. The inventive method has a variety of potential applications in clinical medicine, research, etc., with two of the more important foreseeable applications being stem cell enrichment/isolation, and cancer cell purging.

Mangano, Joseph A.↗
NASA NTRS2009

Cell separation using electric fields

The present invention involves methods and devices which enable discrete objects having a conducting inner core, surrounded by a dielectric membrane to be selectively inactivated by electric fields via irreversible breakdown of their dielectric membrane. One important application of the invention is in the selection, purification, and/or purging of desired or undesired biological cells from cell suspensions. According to the invention, electric fields can be utilized to selectively inactivate and render non-viable particular subpopulations of cells in a suspension, while not adversely affecting other desired subpopulations. According to the inventive methods, the cells can be selected on the basis of intrinsic or induced differences in a characteristic electroporation threshold, which can depend, for example, on a difference in cell size and/or critical dielectric membrane breakdown voltage. The invention enables effective cell separation without the need to employ undesirable exogenous agents, such as toxins or antibodies. The inventive method also enables relatively rapid cell separation involving a relatively low degree of trauma or modification to the selected, desired cells. The inventive method has a variety of potential applications in clinical medicine, research, etc., with two of the more important foreseeable applications being stem cell enrichment/isolation, and cancer cell purging.

Mangano, Joseph↗
NASA NTRS1978

A method for localizing wing flow separation at stall to alleviate spin entry tendencies

A wing leading-edge modification has been developed, applicable at present to single-engine light aircraft, which produces stabilizing vortices at stall and beyond. These vortices have the effect of fixing the stall pattern of the wing such that the various portions of the wing upper surface stall nearly symmetrically. The lift coefficient produced is essentially constant to very high angles of attack above the stall angle of the unmodified wing. It is hypothesized that these characteristics will help prevent inadvertent spin entry after a stall. Results are presented from recent large-scale wind-tunnel tests of a complete light aircraft, both with and without the modification.

Feistel, T. W.↗
NASA NTRSDate not supplied

Aeroacoustic Study of a Subscale Large Civil Transport (STAR) Model – Part 1: Simulations

Results from a computational aeroacoustic study of the Subsonic Transport Aeroacoustic Research (STAR) model are presented. The model, a 26%-scale semispan Boeing 777-200 aircraft, was an inceptive configuration in a comprehensive simulation campaign to accurately predict the airframe noise of a full-scale, large civil transport during landing. The lengthy process of obtaining a high-fidelity, CFD-ready, vetted, digital representation of the model is described in detail. The simulations were performed with the STAR model installed in the NASA Ames 40- by 80-foot full-scale wind tunnel to enable direct comparisons with aerodynamic and acoustic measurements of the model, presented separately in Part 2 of the study. Two versions of the wind tunnel test section were considered. The entire test section was used to simulate the aerodynamic behavior of the model; an open-wall representation of the section was adopted during the acoustic simulations to eliminate wall reflections. To preserve the aerodynamic equivalency of the model for the two simulated tunnel configurations, the open-wall computations were executed at an angle-of-attack one degree higher than that of the corresponding closed-wall tunnel. The effect on aerodynamic behavior of several minor geometry alterations necessary to con-form the simulated to the tested model was assessed – the modifications considerably altered the strength and extent of a flow separation zone on the inboard segment of the flap. Also evaluated was the impact of spatial resolution on aerodynamic and acoustic characteristics of the model – in general, medium resolution was sufficient to establish convergence trends for averaged surface pressure behavior and proper localization of noise sources. After the aeroacoustic characteristics of the baseline configuration were predicted, a toboggan-shaped fairing designed to reduce main landing gear noise was evaluated computationally. Far-field noise spectra for the baseline and toboggan-equipped STAR model were calculated via a Ffowcs-Williams and Hawkings integral approach, with flow quantities on a permeable data surface enclosing the source regions used as input. Results from the simulations indicated that, while the fairing reduced gear noise in the near-field, it had a negligible effect on the far-field noise signature of the model. This trend agreed with previously published experimental results obtained during sub-scale, isolated gear tests and full-scale flight tests

airframe noise↗
NASA NTRS1999

Enhanced protein electrophoresis technique for separating human skeletal muscle myosin heavy chain isoforms

Talmadge and Roy (J. Appl. Physiol. 1993, 75, 2337-2340) previously established a sodium dodecyl sulfate - polyacrylamide gel electrophoresis (SDS-PAGE) protocol for separating all four rat skeletal muscle myosin heavy chain (MHC) isoforms (MHC I, IIa, IIx, IIb); however, when applied to human muscle, the type II MHC isoforms (Ila, IIx) are not clearly distinguished. In this brief paper we describe a modification of the SDS-PAGE protocol which yields distinct and consistent separation of all three adult human MHC isoforms (MHC I, IIa, IIx) in a minigel system. MHC specificity of each band was confirmed by Western blot using three monoclonal IgG antibodies (mAbs) immunoreactive against MHCI (mAb MHCs, Novacastra Laboratories), MHCI+IIa (mAb BF-35), and MHCIIa+IIx (mAb SC-71). Results provide a valuable SDS-PAGE minigel technique for separating MHC isoforms in human muscle without the difficult task of casting gradient gels.

NASA Center JSC↗
NASA NTRS1976

Absorption cell - A modified multiple-traversal device

A modified White-type multiple-transversal absorption cell used with a 5-m Littrow spectrometer is described. It can be introduced at a focus of the radiation beam without altering the beam configuration. The conventional White cell consists of three mirrors of equal focal length, with a distance of two focal lengths separating one of the mirrors from a mirror pair. The modification in the design consists of the addition of two mirrors at a slant placed behind the solitary mirror of the conventional configuration. The mirror arrangement reproduces the configuration of the exit beam for any number of transversals of the cell.

Jennings, D. E.↗
NASA NTRS1977

Improvements and validation of the erythropoiesis control model for bed rest simulation

The most significant improvement in the model is the explicit formulation of separate elements representing erythropoietin production and red cell production. Other modifications include bone marrow time-delays, capability to shift oxyhemoglobin affinity and an algorithm for entering experimental data as time-varying driving functions. An area of model development is suggested by applying the model to simulating onset, diagnosis and treatment of a hematologic disorder. Recommendations for further improvements in the model and suggestions for experimental application are also discussed. A detailed analysis of the hematologic response to bed rest including simulation of the recent Baylor Medical College bed rest studies is also presented.

Leonard, J. I.↗
NASA NTRS1990

Experimental determination of convective heat transfer coefficients in the separated flow region of the Space Shuttle Solid Rocket Motor

A series of cold flow heat transfer tests was conducted with a 7.5-percent scale model of the Space Shuttle Rocket Motor (SRM) to measure the heat transfer coefficients in the separated flow region around the nose of the submerged nozzle. Modifications were made to an existing 7.5 percent scale model of the internal geometry of the aft end of the SRM, including the gimballed nozzle in order to accomplish the measurements. The model nozzle nose was fitted with a stainless steel shell with numerous thermocouples welded to the backside of the thin wall. A transient 'thin skin' experimental technique was used to measure the local heat transfer coefficients. The effects of Reynolds number, nozzle gimbal angle, and model location were correlated with a Stanton number versus Reynolds number correlation which may be used to determine the convective heating rates for the full scale Space Shuttle Solid Rocket Motor nozzle.

Whitesides, R. Harold↗
NASA NTRS1991

Global Expression for Representing Diatomic Potential-Energy Curves

A three-parameter expression that gives an accurate fit to diatomic potential curves over the entire range of separation for charge transfers between 0 and 1. It is based on a generalization of the universal binding-energy relation of Smith et al. (1989) with a modification that describes the crossover from a partially ionic state to the neutral state at large separations. The expression is tested by comparison with first-principles calculations of the potential curves ranging from covalently bonded to ionically bonded. The expression is also used to calculate spectroscopic constants form a curve fit to the first-principles curves. A comparison is made with experimental values of the spectroscopic constants.

Ferrante, John↗
NASA NTRS1992

A fast, uncoupled, compressible, two-dimensional, unsteady boundary layer algorithm with separation for engine inlets

A finite difference boundary layer algorithm was developed to model viscous effects when an inviscid core flow solution is given. This algorithm solved each boundary layer equation separately, then iterated to find a solution. Solving the boundary layer equations sequentially was 2.4 to 4.0 times faster than solving the boundary layer equations simultaneously. This algorithm used a modified Baldwin-Lomax turbulence model, a weighted average of forward and backward differencing of the pressure gradient, and a backward sweep of the pressure. With these modifications, the boundary layer algorithm was able to model flows with and without separation. The number of grid points used in the boundary layer algorithm affected the stability of the algorithm as well as the accuracy of the predictions of friction coefficients and momentum thicknesses. Results of this boundary layer algorithm compared well with experimental observations of friction coefficients and momentum thicknesses. In addition, when used interactively with an inviscid flow algorithm, this boundary layer algorithm corrected for viscous effects to give a good match with experimental observations for pressures in a supersonic inlet.

Roach, Robert L.↗
NASA NTRS1992

A fast, uncoupled, compressible, two-dimensional, unsteady boundary layer algorithm with separation for engine inlets

A finite difference boundary layer algorithm was developed to model viscous effects when an inviscid core flow solution is given. This algorithm solved each boundary layer equation separately, then iterated to find a solution. Solving the boundary layer equations sequentially was 2.4 to 4.0 times faster than solving the boundary layer equations simultaneously. This algorithm used a modified Baldwin-Lomax turbulence model, a weighted average of forward and backward differencing of the pressure gradient, and a backward sweep of the pressure. With these modifications, the boundary layer algorithm was able to model flows with and without separation. The number of grid points used in the boundary layer algorithm affected the stability of the algorithm affected the stability of the algorithm as well as the accuracy of the predictions of friction coefficients and momentum thicknesses. Results of this boundary layer algorithm compared well with experimental observations of friction coefficients and momentum thicknesses. In addition, when used interactively with an inviscid flow algorithm, this boundary layer algorithm corrected for viscous effects to give a good match with experimental observations for pressures in a supersonic inlet.

Roach, Robert L.↗
NASA NTRS1972

Theoretical prediction of interference loading on aircraft stores. Part 3: Programmer's manual

A FORTRAN program is described for predicting interference loading on aircraft stores. An analysis of the program is presented from a programmer's point of view, including program organization, subroutine explanations, and FORTRAN variable definitions. This information is intended for use in any program modification, extension, or troubleshooting efforts. This manual is supplementary to the separately documented program theory and user information.

Danfernandes, F.↗
NASA NTRS1981

Limiting current in electron-beam welders

Damage to workpiece by excessive current in electron-beam welder is prevented by mechanism that accurately adjusts anode-to-cathode spacing. Mechanism is installed on standard Sciaky (or equivalent) electron-beam gun with only minimal modification. By turning knurled knob and observing digital readout of anode/cathode separation, machine operator adjusts welder for safe maximum current before welding begins.

Spiegel, K. W.↗