Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “riders”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Tribological characteristics of nitrogen (N+) implanted iron

The effect of implantation of nitrogen ions (1.5 MeV) on the friction and wear characteristics of pure ion sliding against M-50 steel (unimplanted) was studied in a pin-on-disk sliding friction apparatus. Test conditions included room temperature (25 C), a dry air atmosphere, a load of 1/2 kg (4.9 N), sliding velocities of 0.043 to 0.078 m/sec (15 to 25 rpm), a pure hydrocarbon lubricant (n-hexadecane), or a U.S.P. mineral oil and nitrogen ion implantation doses of 5x10 to the 15th power and 5x10 to the 17th power ions/sq cm. No differences in wear rates were observed in the low dose experiments. In the high dose experiments, small reductions in initial (40 percent) and steady state (20 percent) wear rates were observed for nitrogen implanted iron riders as compared with unimplanted controls. No differences in average friction coefficients were noted for either dose. Auger electron spectroscopy combined with argon ion bombardment revealed a subsurface Gaussian nitrogen distribution with a maximum concentration of 6 atomic percent at a depth of 0.8 microns. Similar analysis within the wear scar of an implanted rider after 20 microns of wear yielded only background nitrogen concentration. No inward migration of nitrogen ions was observed.

Jones, W. R.↗

Plastic deformation and wear process at a surface during unlubricated sliding

The plastic deformation and wear of a 304 stainless steel surface sliding against an aluminum oxide rider with a spherical surface (the radius of curvature: 1.3 cm) were observed by using scanning electron and optical microscopes. Experiments were conducted in a vacuum of one million Pa and in an environment of fifty thousandth Pa of chlorine gas at 25 C. The load was 500 grams and the sliding velocity was 0.5 centimeter per second. The deformed surface layer which accumulates and develops successively is left behind the rider, and step shaped proturbances are developed even after single pass sliding under both environmental conditions. A fully developed surface layer is gradually torn off leaving a characteristic pattern. The mechanism for tearing away of the surface layer from the contact area and sliding track contour is explained assuming the simplified process of material removal based on the adhesion theory for the wear of materials.

Yamamoto, T.↗

Plastic deformation at surface during unlubricated sliding

The plastic deformation and wear of 304 stainless-steel surface slid against an aluminum oxide rider were observed by using a scanning electron microscope and an optical microscope. Experiments were conducted in a vacuum of 0.000001 Pa and in an environment of 0.0005 Pa chlorine gas at 25 C. The load was 500 grams and the sliding velocity was 0.5 centimeter per second. The deformed surface layer which accumulates and develops successively is left behind the rider, and step-shaped protuberances are developed even after single pass sliding under both environmental conditions. A fully developed surface layer is gradually torn off leaving a characteristic pattern. These observations result from both adhesion and an adhesive wear mechanism.

Yamamoto, T.↗

Plastic deformation and wear process at a surface during unlubricated sliding

The plastic deformation and wear of a 304 stainless steel surface sliding against an aluminum oxide rider with a spherical surface (the radius of curvature: 1.3 cm) were observed by using scanning electron and optical microscopes. Experiments were conducted in a vacuum of one million Pa and in an environment of fifty thousandth Pa of chlorine gas at 25 C. The load was 500 grams and the sliding velocity was 0.5 centimeter per second. The deformed surface layer which accumulates and develops successively is left behind the rider, and step shaped proturbances are developed even after single pass sliding under both environmental conditions. A fully developed surface layer is gradually torn off leaving a characteristic pattern. The mechanism for tearing away of the surface layer from the contact area and sliding track contour is explained assuming the simplified process of material removal based on the adhesion theory for the wear of materials. Previously announced in STAR as N82-32735

Yamamoto, T.↗

Tribological characteristics of nitrogen (N+) implanted iron

The effect of implantation of nitrogen ions (1.5 MeV) on the friction and wear characteristics of pure ion sliding against M-50 steel (unimplanted) was studied in a pin-on-disk sliding friction apparatus. Test conditions included room temperature (25 C), a dry air atmosphere, a load of 1/2 kg (4.9 N), sliding velocities of 0.043 to 0.078 m/sec (15 to 25 rpm), a pure hydrocarbon lubricant (n-hexadecane), or a U.S.P. mineral oil and nitrogen ion implantation doses of 5x10 to the 15th power and 5x10 to the 17th power ions/sq cm. No differences in wear rates were observed in the low dose experiments. In the high dose experiments, small reductions in initial (40 percent) and steady state (20 percent) wear rates were observed for nitrogen implanted iron riders as compared with unimplanted controls. No differences in average friction coefficients were noted for either dose. Auger electron spectroscopy combined with argon ion bombardment revealed a subsurface Gaussian nitrogen distribution with a maximum concentration of 6 atomic percent at a depth of 0.8 microns. Similar analysis within the wear scar of an implanted rider after 20 microns of wear yielded only background nitrogen concentration. No inward migration of nitrogen ions was observed. Previously announced in STAR as N82-24322

Jones, W. R., Jr.↗

Friction and wear of iron and nickel in sodium hydroxide solutions

A loaded spherical aluminum oxider rider was made to slide, while in various solutions, on a flat iron or nickel surface reciprocate a distance of 1 cm. Time of experiments was 1 hr during which the rider passed over the center section of the track 540 times. Coeficients of friction were measured throughout the experiments. Wear was measured by scanning the track with a profilometer. Analysis of some of the wear tracks included use of the SEM (scanning electron microscope) and XPS (X-ray photoelectron spectroscopy). Investigated were the effect of various concentrations of NaOH and of water. On iron, increasing NaOH concentration above 0.01 N caused the friction and wear to decrease. This decrease is accompanied by a decrease in surface concentration of ferric oxide (Fe2O3) while more complex iron-oxygen compounds, not clearly identified, also form. At low concentrations of NaOH, such as 0.01 N, where the friction is high, the wear track is badly torn up and the surface is broken. At high concentration, such as 10 N, where the friction is low, the wear track is smooth. The general conclusion is that NaOH forms a protective, low friction film on iron which is destroyed by wear at low concentrations but remains intact at high conentrations of NaOH. Nickel behaves differently than iron in that only a little NaOH gives a low coefficient of friction and a surface which, although roughened in the wear track, remains intact. Previously announced in STAR as N83-10171

Rengstorff, G. P.↗

Ceramic wear in indentation and sliding

The various wear mechanisms involved with single-crystal ceramic materials in indentation and in sliding contacts. Experiments simulating interfacial events have been conducted with hemispherical, conical and pyramidal indenters (riders). With spherical riders, under either abrasive or adhesive conditions, two types of fracture pits have been observed. First, spherical-shaped fracture pits and wear particles are found as a result of either indenting or sliding. These are shown to be due to a spherical-shaped fracture along the circular or spherical stress trajectories. Second, polyhedral fracture pits and debris, produced by anisotropic fracture, and also found both during indenting and sliding. These are primarily controlled by surface and subsurface cracking along cleavage planes. Several quantitative results have also been obtained from this work. For example, using a pyramidal diamond, crack length of Mn-Zn ferrite in the indentation process grows linearly with increasing normal load. Moreover, the critical load to fracture both in indentation and sliding is essentially isotropic and is found to be directly proportional to the indenter radius.

Miyoshi, K.↗

Ceramic wear in indentation and sliding contact

The various wear mechanisms involved with single-crystal ceramic materials in indentation and in sliding contacts. Experiments simulating interfacial events have been conducted with hemispherical, conical and pyramidal indenters (riders). With spherical riders, under either abrasive or adhesive conditions, two types of fracture pits have been observed. First, spherical-shaped fracture pits and wear particles are found as a result of either indenting or sliding. These are shown to be due to a spherical-shaped fracture along the circular or spherical stress trajectories. Second, polyhedral fracture pits and debris, produced by anisotropic fracture, and also found both during indenting and sliding. These are primarily controlled by surface and subsurface cracking along cleavage planes. Several quantitative results have also been obtained from this work. For example, using a pyramidal diamond, crack length of Mn-Zn ferrite in the indentation process grows linearly with increasing normal load. Moreover, the critical load to fracture both in indentation and sliding is essentially isotropic and is found to be directly proportional to the indenter radius.

Miyoshi, K.↗

Body weight of advanced concept hypersonic aircraft

In this paper, preliminary qualitative and quantitative comparisons of the body weight of five hypersonic aircraft configurations are conducted. The five configurations are briefly described as follows: (1) a wing-and-body arrangement with a power-law, circular cross-section body and a delta wing; (2) an all-body vehicle with delta planform and elliptical cross-sections; (3) a wingless wave rider configuration; (4) a winged wave rider configuration; and (5) the spacewing concept, an oblique flying wing at low speed that yaws to 90 deg sweep and flies end-on at hypersonic speeds. The vehicles are defined by their external moldline geometries and by the interior arrangement of their fuel tanks and other components. Intersecting, circular-lobed tankage is used in vehicles with noncircular bodies. The nonusable volume of such concepts is calculated. The structural concept, structural materials, Thermal Protection System, and heat load are allowed to vary with vehicle longitudinal station. Relative strengths and weaknesses of the various hypersonic aircraft concepts in terms of body weight are summarized.

Mark D Ardema↗

Lubricating Properties of Ceramic-Bonded Calcium Fluoride Coatings on Nickel-Base Alloys from 75 to 1900 deg F

The endurance life and the friction coefficient of ceramic-bonded calcium fluoride (CaF2) coatings on nickel-base alloys were determined at temperatures from 75 F to 1900 F. The specimen configuration consisted of a hemispherical rider (3/16-in. rad.) sliding against the flat surface of a rotating disk. Increasing the ambient temperature (up to 1500 F) or the sliding velocity generally reduced the friction coefficient and improved coating life. Base-metal selection was critical above 1500 F. For instance, cast Inconel sliding against coated Inconel X was lubricated effectively to 1500 F, but at 1600 F severe blistering of the coatings occurred. However, good lubrication and adherence were obtained for Rene 41 sliding against coated Rene 41 at temperatures up to 1900 F; no blisters developed, coating wear life was fairly good, and the rider wear rate was significantly lower than for the unlubricated metals. Friction coefficients were 0.12 at 1500 F, 0.15 at 1700 F, and 0.17 at 1800 F and 1900 F. Because of its ready availability, Inconel X appears to be the preferred substrate alloy for applications in which the temperature does not exceed 1500 F. Rene 41 would have to be used in applications involving higher temperatures. Improved coating life was derived by either preoxidizing the substrate metals prior to the coating application or by applying a very thin (less than 0.0002 in.) burnished and sintered overlay to the surface of the coating. Preoxidation did not affect the friction coefficient. The overlay generally resulted in a higher friction coefficient than that obtained without the overlay. The combination of both modifications resulted in longer coating life and in friction coefficients intermediate between those obtained with either modification alone.

Sliney, Harold E.↗

The Turbolift: Linear Sled Hybrid Artificial Gravity Concept

Future crewed space exploration missions into deep space will require enhanced countermeasure technologies to ensure astronaut health. One such hazard is extended exposure to reduced gravity levels (i.e., microgravity, lunar gravity, or Martian gravity). Reduced gravity negatively impacts many physiological systems, leading to hydrostatic intolerance, musculoskeletal atrophy, sensorimotor impairment, bone demineralization, cardiovascular deconditioning, and visual alterations. Various countermeasures have been employed for mitigating these effects, such as exercise, pharmaceuticals, diet, and fluid loading. However, these approaches treat individual symptoms, such that each physiological system is addressed with typically one countermeasure. An alternative to this approach is artificial gravity (AG), which promises to be a holistic, comprehensive countermeasure. The traditional approach to creating AG is through centrifugation. However, centrifugation is not a "pure" form of AG and typically includes the drawbacks of Coriolis forces, gravity gradients, and vestibular cross-coupled illusions.As an alternative, we have proposed a Linear Sled Hybrid (LSH) AG system to mitigate astronauts' physiological deconditioning. This system functions by applying pure linear acceleration to produce footward loading. There is a half rotation (180_) to reorient the rider between acceleration and deceleration phases, such that the loading remains footward, as when standing on Earth. The rotation also provides some footward acceleration to the lower body through centripetal acceleration; hence the "hybrid" aspect of the design. At the end of the deceleration, the rider than accelerates back in the opposite direction and the sequence repeats.This proposed system could be integrated with future crewed space vehicles in a variety of manners.

Gruber, Jason↗

Impacts of Travel Demand Information Diffusion on Reducing Empty Vehicle Miles Traveled by Ridesourcing Vehicles

Ride-hailing or ride-sourcing services provide alternative mobility options in several cities and have seen exponential growth in market share owing to the convenience they provide. Even though usage of such services may be associated with car-light and car-free lifestyles, there are growing concerns around their impact on urban transportation network operations due to empty miles driven without a passenger (deadheading). This study is motivated by the potential for reducing deadhead mileage by providing information on future trip demand to ride-sourcing drivers (at the destination end of their current trip). Future trip demand information enables the driver to wait in place for the next rider without cruising around and contributing to congestion. A machine learning model is applied using historical data to predict hourly and 10-minute future interval demand for ride-sourcing. Two heuristic algorithms have been developed to i) determine drivers that act on demand information received by waiting in place for the next rider, and ii) match drivers who wait to their next trip by minimizing deadheading distance. Data from ride-sourcing providers in Austin, Texas (RideAustin) and in Chengdu, China (DiDi) are leveraged to apply the methodology. Results show that the process results in 68%-82% and 53%-60% trip-level deadheading miles reduction for RideAustin and DiDi sample operations, respectively. As the maximum tolerable driver's waiting time increases, deadheading savings slightly increase. Even if the maximum percentage of drivers waiting is reduced, significant average deadheading savings by trip can be achieved for that portion.

33 ADVANCED PROPULSION SYSTEMS↗

Meeting in the Middle: Pooled Rideshare as Compelling Transportation Offering for Elders

Pooled ridesharing is an innovative new transportation offering with the potential to positively impact traffic and emissions. Through pooling, rideshare can aggregate demand, decreasing the number of vehicles required on the road, but also offering options to those without access to reliable means of transportation. In this study pooled ridesharing is explored in the context of its impacts on seniors. Through analysis of income, location, accessibility, and mode shares, pooled rideshare is demonstrated to offer a compelling middle ground for seniors looking for more affordable transportation than personal vehicles, but who are time sensitive or may not have access to public transportation. An efficient rideshare assignment strategy, which caters to discounts for riders' specific trips, is compared to a more basic heuristic. Results indicate that more riders utilize the service with catered discounts, despite increased wait and travel times over solo rideshare. Additionally, results indicate that although public transportation usage decreases when rideshare service offerings improve, there is not necessarily a direct shift in user base, as even pooled rideshare is still expensive enough to prevent seniors from the lowest household income quartiles from using the service.

Paul, Joseph↗

Improving Experience Beyond the Ride: Joint Assignment and Repositioning for Rideshare

In this study, a novel joint assignment and repositioning strategy is designed, implemented, and tested in a simulated traffic environment. The strategy addresses limitations of previously constructed rideshare repositioning algorithms by integrating the consideration of rider pooling into the optimization. By considering pooling, the strategy can minimize excess vehicle movement and increase riders' use of pooled services over a zonal-flow-based repositioning strategy and a fleet operating with no repositioning at all. The new strategy can increase pooling by up to 2.3% compared to no repositioning in a large region, and up to 0.1% in a small region, without compromising overall fleet revenue. Additionally, compared to a baseline, flow-based repositioning strategy, the new strategy can reduce empty vehicle travel by up to 30% in the larger region, and 2.1% in the smaller simulated area.

Paul, Joseph↗

Interstellar beamer engineering

The fundamental differences between solar sails and interstellar beam riders are presented. Design requirements and design considerations are developed for an interstellar beamer phased array of gigantic proportions of photon pushing beam riding spacecraft to significant fractions of the speed of light.

interstellar↗

Minimal Time Problem with Impulsive Controls

Time optimal control problems for systems with impulsive controls are investigated. Sufficient conditions for the existence of time optimal controls are given. A dynamical programming principle is derived and Lipschitz continuity of an appropriately defined value functional is established. The value functional satisfies a Hamilton–Jacobi–Bellman equation in the viscosity sense. A numerical example for a rider-swing system is presented and it is shown that the reachable set is enlargered by allowing for impulsive controls, when compared to nonimpulsive controls.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Continuous-Time Public Good Contribution Under Uncertainty: A Stochastic Control Approach

In this paper we study continuous-time stochastic control problems with both monotone and classical controls motivated by the so-called public good contribution problem. That is the problem of n economic agents aiming to maximize their expected utility allocating initial wealth over a given time period between private consumption and irreversible contributions to increase the level of some public good. We investigate the corresponding social planner problem and the case of strategic interaction between the agents, i.e. the public good contribution game. We show existence and uniqueness of the social planner’s optimal policy, we characterize it by necessary and sufficient stochastic Kuhn–Tucker conditions and we provide its expression in terms of the unique optional solution of a stochastic backward equation. Similar stochastic first order conditions prove to be very useful for studying any Nash equilibria of the public good contribution game. In the symmetric case they allow us to prove (qualitative) uniqueness of the Nash equilibrium, which we again construct as the unique optional solution of a stochastic backward equation. We finally also provide a detailed analysis of the so-called free rider effect.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

High Order Anchoring and Reinitialization of Level Set Function for Simulating Interface Motion

A second order interface anchoring method has been developed and used with fast sweeping algorithm for reinitialization of a level set function. The algebraic anchoring formulation ensures that the location of the actual interface is preserved, leading to better mass conservation property. It also provides high order accurate algebraic constraint for solving the Eikonal equation on a finite difference grid. Geometric properties of the interface such as surface normal and curvature are subsequently computed from the reinitialized distance function. Various analytical functions for modeling distortion in level set field are considered and accuracy of reinitialization is evaluated using first and second order anchoring schemes. It is also shown that accurate computation of interface curvature requires a high order anchor in addition to a high order fast sweeping method. Mass conservation property of reinitialization is also analyzed by considering test problems from literature including the classic Rider–Kothe single vortex problem. The formulation is suitable for efficient parallelization for both distributed memory and on-node shared memory parallel systems. In conclusion, scalability and performance of the reinitialization scheme on multiple architectures are demonstrated.

97 MATHEMATICS AND COMPUTING↗