Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “research octane number”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

65 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1939

Activation of hydrocarbons and the octane number

This report presents an examination of the history of research on engine knocking and the various types of fuels used in the investigations of this phenomenon. According to this report, the spontaneous ignition of hydrocarbons doped with oxygen follows the logarithmic law within a certain temperature range, but not above 920 degrees K. Having extended the scope of investigations to prove hydrocarbons, the curves of the mixtures burned by air should then be established by progressive replacement of pure iso-octane with heptane. Pentane was also examined in this report.

Peschard, Marcel↗
DOE OSTI2020

Numerical Investigation of Fuel Property Effects on Mixed-Mode Combustion in a Spark-Ignition Engine

In this research, lean mixed-mode combustion is numerically investigated using computational fluid dynamics (CFD) in a spark-ignition engine. A new E30 fuel surrogate is developed using a neural network model with matched octane numbers. A skeletal mechanism is also developed by automated mechanism reduction and by incorporating a NO x submechanism. A hybrid approach that couples the G-equation model and the well-stirred reactor model is employed for turbulent combustion modeling. The developed CFD model is shown to well predict pressure and apparent heat release rate (AHRR) traces compared with experiment. Two types of combustion cycles (deflagration-only and mixed-mode cycles) are observed. The mixed-mode cycles feature early flame propagation and subsequent end-gas auto-ignition, leading to two distinctive AHRR peaks. The validated CFD model is then employed to investigate the effects of NO x chemistry. The NO x chemistry is found to promote auto-ignition through the residual gas, while the deflagration phase remains largely unaffected. Sensitivity analysis is finally performed to understand effects of fuel properties, including heat of vaporization (HoV) and laminar flame speed (S L ). An increased HoV tends to suppress auto-ignition through charge cooling, while the impact of HoV on flame propagation is insignificant. In contrast, an increased S L is found to significantly promote both flame propagation and end-gas auto-ignition. The promoting effect of S L on auto-ignition is not a direct chemical effect; it is rather caused by an advancement of the combustion phasing, which increases compression heating of the end-gas.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Catalyst Development to Overcome Barriers for Commercialization of Synthetic High-Octane Hydrocarbons: Cooperative Research and Development (Final Report)

In recent years, researchers at the National Renewable Energy Laboratory (NREL) and the University of California Berkeley (UC Berkeley) have independently developed catalysts that convert methanol and dimethyl ether into alkylate-like hydrocarbons with a high-octane value, and both have developed intellectual property around these chemical transformations. Both UC Berkeley and NREL wish to see their technologies commercialized to address a number of domestic and international energy challenges. The technologies developed by NREL and UC Berkeley are complimentary but neither have moved beyond the laboratory scale due to remaining challenges with the catalyst activity and selectivity, and/or with the reaction engineering associated with maximizing the yield of the high-value product. NREL and UC Berkeley wish to collaboratively through a shared resources CRADA to solve issues related to the scale-up and process integration of their high-octane hydrocarbon technologies, thus enabling future licensing of the technology to an industry partner.

10 SYNTHETIC FUELS↗
DOE OSTI2020

A Perspective on Biomass-Derived Biofuels: From Catalyst Design Principles to Fuel Properties

The hazards to health and the environment associated with the transportation sector include smog, particulate matter, and greenhouse gas emissions. Conversion of lignocellulosic biomass into biofuels has the potential to provide significant amounts of infrastructure-compatible liquid transportation fuels that reduce those hazardous materials. However, the development of these technologies is inefficient, due to: (i) the lack of a priori fuel property consideration, (ii) poor shared vocabulary between process chemists and fuel engineers, and (iii) modern and future engines operating outside the range of traditional autoignition metrics such as octane or cetane numbers. In this perspective, we describe an approach where we follow a “fuel-property first” design methodology with a sequence of (i) identifying the desirable fuel properties for modern engines, (ii) defining molecules capable of delivering those properties, and (iii) designing catalysts and processes that can produce those molecules from a candidate feedstock in a specific conversion process. Computational techniques need to be leveraged to minimize expenses and experimental efforts on low-promise options. This concept is illustrated with current research information available for biomass conversion to fuels via catalytic fast pyrolysis and hydrotreating; outstanding challenges and research tools necessary for a successful outcome are presented.

BIOMASS FUELS↗
DOE OSTI2022

Impact of Fuel Properties on the Combustion of Late Post Injections used for Aftertreatment Thermal Management

Typical calibration for catalyst thermal management for compression-ignition engines involves delaying the post-injection into the expansion stroke. Reduced work extraction due to the late heat release event is used to increase the exhaust gas temperature to shorten the time associated with reaching optimal temperatures for aftertreatment systems. Shorter catalyst heat-up time can simultaneously reduce tail-pipe emissions and the typical fuel penalties associated with this mode of operation. In this study, the effects of volatility, reactivity, and oxygen content of the fuel on combustion stability and emissions were studied in a light-duty single-cylinder research engine. Blends of iso-octane/ n-heptane and farnesane/ 2,2,4,4,6,8,8-heptamethylnonane were used to study the impacts of volatility and reactivity. At constant reactivity, little to no variation in combustion performance was observed due to differences in volatility. On the other hand, increased reactivity improved combustion stability and efficiency at late injection timings (+24 CAD). The combined effect of increase in chemical reactivity and oxygen content was analysed by comparing the baseline #2 diesel operation with two blends of mono-ethers and #2 diesel to achieve cetane numbers (CNs) of 45 and 55, and a pure blend of mono-ether components with CN > 100. Fuels with higher reactivity and oxygen content were found to reduce engine-out hydrocarbon and carbon mono-oxide emissions while also achieving stable combustion at post-injection timings later than those achievable with diesel fuel. The pure ether-blend had the latest achievable post-injection timing (≥+26 CAD) while still maintaining stable combustion. At similar combustion stability, the pure ether blend was found to have 2.8% higher combustion efficiency and 4.3% higher thermal efficiency than the baseline diesel. The ether-diesel blends at CN45 and CN55 were found to have 1.8% higher combustion efficiency than baseline diesel. The results demonstrate that fuels with increased reactivity can increase combustion efficiency, reducing carbon monoxide and hydrocarbon emissions, while maintaining similar exhaust temperature and combustion stability compared to baseline diesel. Further greenhouse gas benefits can also be realized as the mono-ether bioblendstocks show potential for >50% reduction in greenhouse gas emissions relative to diesel fuel based on their production method.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2022

Enhancing $\phi$-sensitivity of ignition delay times through dilution of fuel-air mixture

The high $\phi$-sensitivity (η) of ignition delay time (τ IDT ) is one of the desirable fuel properties for the high-load extension of advanced compression ignition engine. Recent studies revealed the effectiveness of a high dilution rate (x D ) for enhancing η at the engine-relevant conditions. This study aims to quantify the effect of dilution on the η of isooctane using a combined experiment-simulation approach. The ignition delay of the isooctane/air mixture was measured with an Advanced Fuel Ignition Delay Analyzer (AFIDA) over the temperature range of 623 - 923 K at 10 bar pressure with global $\phi$ = 0.3 - 0.6, with and without 28.6% of additional N 2 dilution. For precise evaluation of experimental η, the facility effect of the AFIDA experiment was characterized with three-dimensional computational fluid dynamics (3-D CFD) simulation. The temperature in the combustion chamber from 3-D CFD indicated a substantial temporal dependency, varying up to ~52 K by charge-cooling of fuel injection and heat transfer from the wall. We introduced the dimensionless number θ(t) for characterizing the temporal profile of chamber temperature. Consideration of the facility effect using θ(t) resulted in better agreement between the experimental ..eta.. and zero-dimensional (0-D) kinetics simulation. The refined η were then further utilized to quantify the effectiveness of dilution to η The extent of η enhancement with dilution strategy was maximized at the low-temperature chemistry regime, increasing η by 77% with a 28.6% dilution rate. Further analysis on the dilution effect was carried out using 0-D kinetics simulation, revealing the critical dimensionless numbers relevant to the effectiveness of dilution to η enhancement. Here, this study is the first experiment-simulation combined research to quantify the effect of dilution on η, facilitating the kinetics model refinement for better reproduction of $\phi$-sensitivity.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

Gasoline Compression Ignition (GCI) on a Light-Duty Multi-Cylinder Engine Using a Wide Range of Fuel Reactivities and Heavy Fuel Stratification

Many research studies have focused on utilizing gasoline in modern compression ignition engines to reduce emissions and improve efficiency. Collectively, this combustion mode has become known as gasoline compression ignition (GCI). One of the biggest challenges with GCI operation is maintaining control over the combustion process through the fuel injection strategy, such that the engine can be controlled on a cycle-by-cycle basis. Research studies have investigated a wide variety of GCI injection strategies (i.e., fuel stratification levels) to maintain control over the heat release rate while achieving low temperature combustion (LTC). This work shows that at loads relevant to light-duty engines, partial fuel stratification (PFS) with gasoline provides very little controllability over the timing of combustion. On the contrary, heavy fuel stratification (HFS) provides very linear and pronounced control over the timing of combustion. However, the HFS strategy has challenges achieving LTC operation due to the air handling burdens associated with the high EGR rates that are required to reduce NOx emissions to near zero levels. In this work, a wide variety of gasoline fuel reactivities (octane numbers ranging from < 40 to 87) were investigated to understand the engine performance and emissions of HFS-GCI operation on a multi-cylinder light-duty engine. The results indicate that over an EGR sweep at 4 bar BMEP, the gasoline fuels can achieve LTC operation with ultra-low NOx and soot emissions, while conventional diesel combustion (CDC) is unable to simultaneously achieve low NOx and soot. At 10 bar BMEP, all the gasoline fuels were compared to diesel, but using mixing controlled combustion and not LTC.

Dempsey, Adam↗
DOE OSTI2021

Gasoline Compression Ignition on a Light-Duty Multi-Cylinder Engine Using a Wide Range of Fuel Reactivities and Heavy Fuel Stratification

Many research studies have focused on utilizing gasoline in modern compression ignition engines to reduce emissions and improve efficiency. Collectively, this combustion mode has become kn+own as gasoline compression ignition (GCI). One of the biggest challenges with GCI operation is maintaining control over the combustion process through the fuel injection strategy, such that the engine can be controlled on a cycle-by-cycle basis. Research studies have investigated a wide variety of GCI injection strategies (i.e., fuel stratification levels) to maintain control over the heat release rate while achieving low-temperature combustion (LTC). This work shows that at loads relevant to light-duty engines, partial fuel stratification (PFS) with gasoline provides very little controllability over the timing of combustion. On the contrary, heavy fuel stratification (HFS) provides very linear and pronounced control over the timing of combustion. However, the HFS strategy has challenges achieving LTC operation due to the air handling burdens associated with the high exhaust gas recirculation (EGR) rates that are required to reduce NOx emissions to near zero levels. In this work, a wide variety of gasoline fuel reactivities (octane numbers ranging from <40 to 87) were investigated to understand the engine performance and emissions of HFS-GCI operation on a multi-cylinder light-duty engine. Overall, the results indicate that over an EGR sweep at 4 bar brake mean effective pressure (BMEP), the gasoline fuels can achieve LTC operation with ultra-low NO x and soot emissions, while conventional diesel combustion (CDC) is unable to simultaneously achieve low NO x and soot. At 10 bar BMEP, all the gasoline fuels were compared to diesel, but using mixing controlled combustion and not LTC.

33 ADVANCED PROPULSION SYSTEMS↗
DOE OSTI2020

MULTI-DIMENSIONAL MODELING OF THE CFR ENGINE FOR THE INVESTIGATION OF SI NATURAL GAS COMBUSTION AND CONTROLLED END-GAS AUTOIGNITION

Engine knock and misfire are barriers to pathways leading to high-efficiency Spark-Ignited (SI) Natural Gas engines. The general tendency to knock is highly dependent on engine operating conditions and the fuel reactivity. The problem is further complicated by low emission limits and the wide range of chemical reactivity in pipeline quality natural gas. Depending on the region and the source of the natural gas, its reactivity, described by its methane number (analogous to the octane number for liquid SI fuels) can span from 65 - 95. In order to realize diesel-like efficiencies, SI natural gas engines must be designed to operate at high BMEP near knock limits over a wide range of fuel reactivity. This requires a deep understanding regarding the combustion-engine interactions pertaining to flame propagation and end-gas autoignition (EGAI). However, EGAI, if controlled, provides an opportunity to increase SI natural gas engine efficiency by increasing combustion rate and the total burned fuel, mitigating the effects of the slow flame speeds of natural gas fuels which generally reduce BMEP and increase unburned hydrocarbon emissions. For this reason, in order to study EGAI phenomenon, the present work highlights multi-dimensional computational fluid dynamics (CFD) models of the Cooperative Fuel Research (CFR) engine. The CFR engine models are used to investigate fuel-engine interactions that lead to EGAI with natural gas, including effects of fuel reactivity, engine operating parameters, and exhaust gas recirculation (EGR). A Three-Pressure Analysis, performed with GT-Power, was used to estimate initial and boundary conditions for the three-dimensional CFD model. CONVERGE CFD v2.4 was used for the three-dimensional CFD modeling where the level set G-Equation model and SAGE detailed chemical kinetics solver were used. An assessment of the different modeling approaches is also provided to evaluate their limitations, advantages and disadvantages, and for which situations they are most applicable. Model validation was performed with experimental data taken with a CFR engine over varying compression ratio, CA50, EGR fraction, and IMEP and shows good agreement in Peak Cylinder Pressure (PCP), PCP crank angle, and the location of the 10%, 50%, and 90% mass fraction burned (CA10, CA50, and CA90, respectively). The models can predict the onset crank angle and pressure rise rate for light, medium, and heavy EGAI under a variety of fuel reactivities and engine operating conditions.

Bestel, Diego↗
DOE OSTI2021

History of Ethanol Fuel Adoption in the United States: Policy, Economics, and Logistics

Ethanol has the achieved the greatest market share of all the alternative transportation fuels that have been researched, developed, and deployed in the US. There are multiple lessons to be learned from the history of ethanol adoption that can be applied to future fuels and products. Ethanol has replaced portions of gasoline in three main blend levels, with corresponding vehicles, equipment, benefits, and policies. The first is E10, which has replaced nearly all pure gasoline (E0) sold in the United States today (U.S. Energy Information Administration 2015). This was brought about through generations of policies that were motivated by multiple factors related to engine performance, energy security, health, air quality, and climate protection. Ethanol's high octane has been a consistent driver of the fuel because this enables higher performance engines. Early policies (1973-1979) were largely motivated by the desire to reduce dependence on petroleum sourced from members of the Organization of the Petroleum Exporting Countries, or OPEC. Fuel policy in the 1980s was largely in pursuit of promoting octane number enhancers that could replace lead. Criteria pollutant reduction was the overarching goal of actions taken from 1990 to 2005. From 2005 to the present, fuel policy has been largely motivated by energy security and climate protection goals. These policies were usually technology-agnostic and promoted multiple fuels and additives during each period. However, ethanol is the only fuel identified that is cost effective with qualities that enabled it to prosper in the policy environments of all four of these periods.The second market for ethanol is via 85% ethanol (E85). This fuel has the advantage of a greater concentration of ethanol but the disadvantage of not being compatible with regular gasoline vehicles. Instead, it can only be used in flexible-fuel vehicle (FFVs), which can use every blend level from E0 to E85. Therefore, much of the effort to increase E85 consumption has been aimed at incentivizing automakers to manufacture FFVs, drivers to purchase FFVs, and fueling stations to equip themselves to sell E85.The third, and newest, market through which ethanol is consumed is 15% ethanol (E15), which builds upon the E10 market to increase ethanol consumption by common gasoline vehicles. Efforts to create the E15 market consisted largely of testing vehicles and refueling equipment for compatibility, creating waivers to allow the use of E15, placing requirements on E15 retailers, and incentivizing retailers to equip themselves to purchase E15.

09 BIOMASS FUELS↗
NASA NTRS2004

Subsonic Aircraft With Regression and Neural-Network Approximators Designed

At the NASA Glenn Research Center, NASA Langley Research Center's Flight Optimization System (FLOPS) and the design optimization testbed COMETBOARDS with regression and neural-network-analysis approximators have been coupled to obtain a preliminary aircraft design methodology. For a subsonic aircraft, the optimal design, that is the airframe-engine combination, is obtained by the simulation. The aircraft is powered by two high-bypass-ratio engines with a nominal thrust of about 35,000 lbf. It is to carry 150 passengers at a cruise speed of Mach 0.8 over a range of 3000 n mi and to operate on a 6000-ft runway. The aircraft design utilized a neural network and a regression-approximations-based analysis tool, along with a multioptimizer cascade algorithm that uses sequential linear programming, sequential quadratic programming, the method of feasible directions, and then sequential quadratic programming again. Optimal aircraft weight versus the number of design iterations is shown. The central processing unit (CPU) time to solution is given. It is shown that the regression-method-based analyzer exhibited a smoother convergence pattern than the FLOPS code. The optimum weight obtained by the approximation technique and the FLOPS code differed by 1.3 percent. Prediction by the approximation technique exhibited no error for the aircraft wing area and turbine entry temperature, whereas it was within 2 percent for most other parameters. Cascade strategy was required by FLOPS as well as the approximators. The regression method had a tendency to hug the data points, whereas the neural network exhibited a propensity to follow a mean path. The performance of the neural network and regression methods was considered adequate. It was at about the same level for small, standard, and large models with redundancy ratios (defined as the number of input-output pairs to the number of unknown coefficients) of 14, 28, and 57, respectively. In an SGI octane workstation (Silicon Graphics, Inc., Mountainview, CA), the regression training required a fraction of a CPU second, whereas neural network training was between 1 and 9 min, as given. For a single analysis cycle, the 3-sec CPU time required by the FLOPS code was reduced to milliseconds by the approximators. For design calculations, the time with the FLOPS code was 34 min. It was reduced to 2 sec with the regression method and to 4 min by the neural network technique. The performance of the regression and neural network methods was found to be satisfactory for the analysis and design optimization of the subsonic aircraft.

Patnaik, Surya N.↗