Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “reading error”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1978

Semi-automatic aircraft control system

A flight control type system which provides a tactile readout to the hand of a pilot for directing elevator control during both approach to flare-out and departure maneuvers. For altitudes above flare-out, the system sums the instantaneous coefficient of lift signals of a lift transducer with a generated signal representing ideal coefficient of lift for approach to flare-out, i.e., a value of about 30% below stall. Error signals resulting from the summation are read out by the noted tactile device. Below flare altitude, an altitude responsive variation is summed with the signal representing ideal coefficient of lift to provide error signal readout.

Gilson, Richard D.↗
DOE OSTI2026

A scalable superconducting nanowire memory array with row–column addressing

Scalable superconducting memory is required for the development of low-energy superconducting computers and fault-tolerant quantum computers. Conventional superconducting logic-based memory cells possess a large footprint that limits scaling; nanowire-based superconducting memory cells, although more compact, have high error rates, which hinders integration into large arrays. Here we report a 4 × 4 superconducting nanowire memory array that is designed for scalable row–column operations and has a functional density of 2.6 Mbit cm −2 . Each memory cell is based on a nanowire loop consisting of two temperature-dependent superconducting switches and a variable kinetic inductor. The arrays operate at 1.3 K, where we implement and characterize multiflux quanta state storage and destructive read-out. By optimizing the write- and read-pulse sequences, we minimize bit errors and maximize operating margins. We achieve a minimum bit error rate of 10 −5 . Here, we also use circuit-level simulations to understand the memory cell’s dynamics, performance limits and stability under varying pulse amplitudes.

Electrical and electronic engineering↗
NASA NTRS1939

The Effect of Compressibility on the Pressure Reading of a Prandtl Pitot Tube at Subsonic Flow Velocity

Errors arising from yawed flow were also determined up to 20 degrees angle of attack. In axial flow, the Prandtl pitot tube begins at w/a approx. = 0.8 to give an incorrect static pressure reading, while it records the tank pressure correctly, as anticipated, up to sonic velocity. Owing to the compressibility of the air, the Prandtl pitot tube manifests compression shocks when the air speed approaches velocity of sound. This affects the pressure reading of the instrument. Because of the increasing importance of high speed in aviation, this compressibility effect is investigated in detail.

Walchner, O↗
NASA NTRS2000

Calibration of a Spacecraft Gyro Quadruplet

This work presents a new approach to gyro calibration where, in addition to being used for computing attitude that is needed in the calibration process, the gyro outputs are also used as measurements in a Kalman filter. Gyro calibration as well as calibration of other instruments occurs in two steps. In the first step, the instrument error parameters are estimated. During the second stage, those errors are continuously removed from the gyro readings. In the classical approach to gyro calibration, the gyro outputs are used to maintain or compute body orientation rather than being used as measurements in the context of filtering. In inertial navigation, for example, gyro errors cause erroneous computation of velocity and position, and then when the latter are compared to measured velocity and position, a great portion of the computed velocity and position errors can be determined. The latter errors are then fed into a Kalman filter (KF) that uses the INS error model to infer on the gyro errors. Similarly, when applying the classical approach to spacecraft (SC) altitude determination, the gyro outputs are used to compute the attitude and then attitude measurements are used to determine the attitude errors, which again using a KF, indicates what the gyro errors are. In the approach adopted in this work the gyro outputs are used as angular rate measurements and are compared to estimated angular rate measurements. However, this approach requires the knowledge of the angular rate. In the past, the estimated angular rate was computed in a rather simplistic way assuming that the rate was constant. In the present work, the estimated angular rate is derived using a KF whose input can be any kind of attitude measurement, therefore the angular rate experienced by the SC can be continuously changing, and yet a good estimate of the rate, necessary for calibration, can be obtained.

Harman, Richard R.↗
DOE OSTI2021

Fast and accurate metagenotyping of the human gut microbiome with GT-Pro

Single nucleotide polymorphisms (SNPs) in metagenomics are used to quantify population structure, track strains and identify genetic determinants of microbial phenotypes. However, existing alignment-based approaches for metagenomic SNP detection require high-performance computing and enough read coverage to distinguish SNPs from sequencing errors. To address these issues, we developed the GenoTyper for Prokaryotes (GT-Pro), a suite of methods to catalog SNPs from genomes and use unique k-mers to rapidly genotype these SNPs from metagenomes. Compared to methods that use read alignment, GT-Pro is more accurate and two orders of magnitude faster. Here, using high-quality genomes, we constructed a catalog of 104 million SNPs in 909 human gut species and used unique k-mers targeting this catalog to characterize the global population structure of gut microbes from 7,459 samples. GT-Pro enables fast and memory-efficient metagenotyping of millions of SNPs on a personal computer.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2022

Effects-Based Monitoring of Geomagnetically-Induced Current Using a Convolutional Neural Network

Geomagnetically-induced current (GIC) due to space weather can flow in the power grid causing undesirable effects such as transformer overheating, misoperation of protection devices, and potential blackouts. It is therefore important to monitor GIC in the power grid to improve online situational awareness and decision-making of system operators during a geomagnetic disturbance. To avoid the costly installation of GIC monitors at transformers’ neutrals, it is desirable to find correlations between GIC and already-monitored parameters. Hence, this work proposed the use of a convolutional neural network (CNN) to compute GIC amplitudes from learned patterns in the time-series data of transformer even harmonic currents. Using an electromagnetic transient program, GIC injection simulations were performed for a modeled Dominion Energy Virginia (DEV) substation with two 504 MVA, 500/230 kV transformers. Data collected from these offline simulations were used to train the CNN to provide online GIC monitoring. Testing the CNN performance involved using real GIC measurements from published literature and from a physical GIC monitor in the DEV area. Finally, the results showed that the proposed method was able to provide GIC readings with a root mean squared error of 1.56 A/phase (equivalent to an average accuracy of 94%) for these real GIC waveforms.

42 ENGINEERING↗
NASA NTRS1975

Digital tape drive monitor

Network checks skew and character spacing of digital tape drive systems automatically. Tape drive is set up and calibrated to check any written tape when tape is read back. It will indicate track errors or character spacing errors should they exceed specifications.

Mckenna, R. T.↗
NASA NTRS1947

Low-Speed Wind-Tunnel Tests of a Pilotless Aircraft Having Horizontal and Vertical Wings and Cruciform Tail

Low-speed tests of a pilotless aircraft were conducted in the Langley propeller-research tunnel to provide information for the estimation of the longitudinal stability and. control, to measure the aileron effectiveness, and to calibrate the radome and the Machmeter pitot-static orifices. It was found that the model possessed a stEb.le variation of elevator angle required for trim throughout the speed range at the design angle of attack. A comparison of the airplane with and without JATO units and with an alternate rocket booster showed that a large loss in longitudinal stability and control resulting from the addition of the rocket booster to the aircraft was sufficient to make the rocket-booster assembly unsatisfactory as an alternate for the JATO units. Reversal of the aileron effectiveness was evident at positive deflections of the vertical wing flap indicating that the roll-stabilization system would produce roiling moments in a tight right turn contrary to its design purpose. Vertical-wing-flap deflections caused large errors in the static-pressure reading obtained by the original static-tube installation. A practical installation point on the fuselage was located which should yield reliable measurement of the free-stream static pressure.

Mastrocola, N↗
NASA NTRS2008

Precision Attitude Determination for an Infrared Space Telescope

We have developed performance simulations for a precision attitude determination system using a focal plane star tracker on an infrared space telescope. The telescope is being designed for the Destiny mission to measure cosmologically distant supernovae as one of the candidate implementations for the Joint Dark Energy Mission. Repeat observations of the supernovae require attitude control at the level of 0.010 arcseconds (0.05 microradians) during integrations and at repeat intervals up to and over a year. While absolute accuracy is not required, the repoint precision is challenging. We have simulated the performance of a focal plane star tracker in a multidimensional parameter space, including pixel size, read noise, and readout rate. Systematic errors such as proper motion, velocity aberration, and parallax can be measured and compensated out. Our prediction is that a relative attitude determination accuracy of 0.001 to 0.002 arcseconds (0.005 to 0.010 microradians) will be achievable.

Benford, Dominic J.↗
NASA NTRS1989

Detection and avoidance of errors in computer software

The acceptance test errors of a computer software project to determine if the errors could be detected or avoided in earlier phases of development. GROAGSS (Gamma Ray Observatory Attitude Ground Support System) was selected as the software project to be examined. The development of the software followed the standard Flight Dynamics Software Development methods. GROAGSS was developed between August 1985 and April 1989. The project is approximately 250,000 lines of code of which approximately 43,000 lines are reused from previous projects. GROAGSS had a total of 1715 Change Report Forms (CRFs) submitted during the entire development and testing. These changes contained 936 errors. Of these 936 errors, 374 were found during the acceptance testing. These acceptance test errors were first categorized into methods of avoidance including: more clearly written requirements; detail review; code reading; structural unit testing; and functional system integration testing. The errors were later broken down in terms of effort to detect and correct, class of error, and probability that the prescribed detection method would be successful. These determinations were based on Software Engineering Laboratory (SEL) documents and interviews with the project programmers. A summary of the results of the categorizations is presented. The number of programming errors at the beginning of acceptance testing can be significantly reduced. The results of the existing development methodology are examined for ways of improvements. A basis is provided for the definition is a new development/testing paradigm. Monitoring of the new scheme will objectively determine its effectiveness on avoiding and detecting errors.

Kinsler, Les↗
NASA NTRS1994

Optical storage media data integrity studies

Optical disk-based information systems are being used in private industry and many Federal Government agencies for on-line and long-term storage of large quantities of data. The storage devices that are part of these systems are designed with powerful, but not unlimited, media error correction capacities. The integrity of data stored on optical disks does not only depend on the life expectancy specifications for the medium. Different factors, including handling and storage conditions, may result in an increase of medium errors in size and frequency. Monitoring the potential data degradation is crucial, especially for long term applications. Efforts are being made by the Association for Information and Image Management Technical Committee C21, Storage Devices and Applications, to specify methods for monitoring and reporting to the user medium errors detected by the storage device while writing, reading or verifying the data stored in that medium. The Computer Systems Laboratory (CSL) of the National Institute of Standard and Technology (NIST) has a leadership role in the development of these standard techniques. In addition, CSL is researching other data integrity issues, including the investigation of error-resilient compression algorithms. NIST has conducted care and handling experiments on optical disk media with the objective of identifying possible causes of degradation. NIST work in data integrity and related standards activities is described.

Podio, Fernando L.↗
DOE OSTI2021

VERAIO Software Management Plan

VERAIO is a set of utility codes used to provide a common set of input and outputs to the Virtual Environment for Reactor Applications (VERA). VERA is a collection of several different computer codes that all have a common input and output. This prevents the need to manage input and output from each individual code, allowing for ease of use and reducing errors associated with code operability. The VERAIO utilities include VERAIn, VERAView, and VERARun. Each of these utilities is described below. VERAIn is an input processor that reads an ASCII input file generated by users, parses the file, performs some error checking, and writes an XML file to be read by other VERA codes. The main purpose of VERAIn is to provide a common input to all of the VERA codes so users only need to learn one input. VERAIn is written in Perl and uses YAML configuration files to provide flexibility. VERAView is a graphical user interface (GUI) that reads a VERA HDF output file and allows users to visualize results. VERAView is written in Python. VERARun is a script that drives the VERA execution in a high performance computing (HPC) environment. Work performed at the code level supports the Quality Assurance Program Plan (QAPP) (VERA-QA-001), and VERA Software Quality Assurance Plan (VERA-QA-002).

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

VERAIO Software Management Plan

VERAIO is a set of utility codes used to provide a common set of inputs and outputs to the Virtual Environment for Reactor Applications (VERA). VERA is a collection of several different computer codes that all have a common input and output. This prevents the need to manage input and output from each individual code, allowing for ease of use and reducing errors associated with code operability. The VERAIO utilities include VERAIn, VERAView, and VERARun. Each of these utilities is described below. VERAIn is an input processor that reads an ASCII input file generated by users, parses the file, performs some error checking, and writes an XML file to be read by other VERA codes. The main purpose of VERAIn is to provide a common input to all of the VERA codes, so users only need to learn one input. VERAIn is written in Perl and uses YAML configuration files to provide flexibility. VERAView is a graphical user interface (GUI) that reads a VERA hierarchical data format (HDF) output file and allows users to visualize results. VERAView is written in Python. VERARun is a script that drives the VERA execution in a high performance computing (HPC) environment. Work performed at the code level supports the quality assurance program plan (QAPP) (VERA-QA-001) and the VERA Software Quality Assurance Plan (VERA-QA-002).

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2022

Energy Exascale Earth System Model v2.0.1

First patch release of v2.0.0 Changes since v2.0.0 [Important change] Fix ocean threading bug seen in debug cases on Chrysalis with Intel 20.0.4. Was introduced around time of v2.0.0 tag. Does not change v2.0.0 answers on Chrysalis because those didn't use threading or debugging. [EAM] Add semi-lagrangian tracer transport for theta-l (F90 and C++), add new algorithm for finding tropopause, add DSCREAM to allow v2 and SCREAM settings in same code such as adjust_ps [EAM-MMF] 60L default, allow C++ back end of RRTMGP (EAM too). [EAMxx] add nu-top functionality, fix forcing functor, add ttype9 and dcmip2012 tests 2.1, 2.2, and 3 HOMME: remove obsolete remap algs, option to specify dynamics alg indep of tracer, new sponge layer, add imex tests [ELM] Add topography-based subgrid (topounits), add FATES-ELM Nitro., Phos. and CH4 coupling, add land-use ts for NARRM, add lulc for SSP3 RCP7, Fix nutrient fertilization exp test and carbon isotope flux, Fix xactive lnd dry deposition, add lake water storage option, fix plant hydraulics 2d params, fix carbon budget calc, fix soil nutrient conc. bug, fix mosart dam bug, add test for new ELM, MOSART features, fix bug in O3 dry dep stomatal resistances, fix plant hydraulics restart BFB error, update mkmapdata. [MOSART] fix bug for reading the latitude from an unstructured input file, fix oversat in bubble test. [MPAS-ocean] Add CFC11, CFC12 tracers, add 2D spherical transport tests, fix del4 tracer mixing, add MARBL ocean tracer mixing, modify harmonic analysis options, add GPU port of vmix routines, fix calc of ML-averaged BV freq. [MPAS-seaice] Change extents of initial polar disks for oRRS18to6v3 grid, fix ice BGC with MARBL, update spherical test cases, fix DON coupling, Remove Cf from sea ice constants. [MPAS-landice] add CRYO1850-4xCO2 compset [CIME] add GCP, ANL GCE, Spock, Perlmutter, deprecate config_compilers.xml, fix and clean-up cmake macros, fix slurm bindings, refactor CIME internal testing, cleanup SCORPIO perf data, allow position independent compset naming, [also] update v2 benchmarking suite, extend e3sm_prod with throughput and memory checks

E3SM Project, DOE↗
NASA NTRS1977

Attitude determination techniques for Nimbus 6 and Nimbus G

Techniques for measuring attitude deviations in the Nimbus 6 and Nimbus G 3-axis stabilized, zero-momentum, earth observation satellites are presented. The on-orbit telemetered data include scanner roll and pitch error signals, an illuminated DSAS which can read the azimuth and elevation of the sunline when the spacecraft is not in the umbra, the signal from the single gyro in the RMP, and the momenta of the reaction wheels. Mathematical methods for interpreting the measured data are described with attention to filter equations, especially the Kalman filter because of its ability to eliminate high frequency noise.

Das, A.↗
NASA NTRS2016

Exploratory Analysis of Carbon Dioxide Levels and Ultrasound Measures of the Eye During ISS Missions

Carbon dioxide (CO2) levels on ISS have typically averaged 2.3 to 5.3mm Hg, with large fluctuations occurring over periods of hours and days. CO2 has effects on cerebral vascular tone, resulting in vasodilation and alteration of cerebral blood flow(CBF). Increased CBF leads to elevated intracranial pressure(ICP), which is a factor leading to visual disturbance, headaches, and other central nervous system symptoms. Ultrasound of the optic nerve provides a surrogate measurement of ICP. Inflight ultrasounds were implemented as an enhanced screening tool for the Visual Impairment/Intracranial Pressure (VIIP) Syndrome. This analysis examines the relationships between ambient CO2 levels on ISS and ultrasound measures of the eye in an effort to understand how CO2 may be associated with VIIP and to inform future analysis of inflight VIIP data. Results as shown in Figure2, there was a large timeframe where CO2 readings were removed due to sensor fault errors(see Limitations), from June 2011 to January 2012. After extensive cleaning of the CO2 data, metrics for all of the data were calculated (Table2). Preliminary analyses showed possible associations between variability measures of CO2 and AP diameter (Figure3),and average CO2 exposure and ONSD(Figure4). Adjustments for multiple comparisons were not made due to the exploratory nature of the analysis.

Schaefer, C.↗