Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “quality inspection”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS2010

Design Considerations for Human Rating of Liquid Rocket Engines

I.Human-rating is specific to each engine; a. Context of program/project must be understood. b. Engine cannot be discussed independently from vehicle and mission. II. Utilize a logical combination of design, manufacturing, and test approaches a. Design 1) It is crucial to know the potential ways a system can fail, and how a failure can propagate; 2) Fault avoidance, fault tolerance, DFMR, caution and warning all have roles to play. b. Manufacturing and Assembly; 1) As-built vs. as-designed; 2) Review procedures for assembly and maintenance periodically; and 3) Keep personnel trained and certified. c. There is no substitute for test: 1) Analytical tools are constantly advancing, but still need test data for anchoring assumptions; 2) Demonstrate robustness and explore sensitivities; 3) Ideally, flight will be encompassed by ground test experience. III. Consistency and repeatability is key in production a. Maintain robust processes and procedures for inspection and quality control based upon development and qualification experience; b. Establish methods to "spot check" quality and consistency in parts: 1) Dedicated ground test engines; 2) Random components pulled from the line/lot to go through "enhanced" testing.

Parkinson, Douglas↗
NASA NTRS2012

Heat Shield Employing Cured Thermal Protection Material Blocks Bonded in a Large-Cell Honeycomb Matrix

A document describes a new way to integrate thermal protection materials on external surfaces of vehicles that experience the severe heating environments of atmospheric entry from space. Cured blocks of thermal protection materials are bonded into a compatible, large-cell honeycomb matrix that can be applied on the external surfaces of the vehicles. The honeycomb matrix cell size, and corresponding thermal protection material block size, is envisioned to be between 1 and 4 in. (.2.5 and 10 cm) on a side, with a depth required to protect the vehicle. The cell wall thickness is thin, between 0.01 and 0.10 in. (.0.025 and 0.25 cm). A key feature is that the honeycomb matrix is attached to the vehicle fs unprotected external surface prior to insertion of the thermal protection material blocks. The attachment integrity of the honeycomb can then be confirmed over the full range of temperature and loads that the vehicle will experience. Another key feature of the innovation is the use of uniform-sized thermal protection material blocks. This feature allows for the mass production of these blocks at a size that is convenient for quality control inspection. The honeycomb that receives the blocks must have cells with a compatible set of internal dimensions. The innovation involves the use of a faceted subsurface under the honeycomb. This provides a predictable surface with perpendicular cell walls for the majority of the blocks. Some cells will have positive tapers to accommodate mitered joints between honeycomb panels on each facet of the subsurface. These tapered cells have dimensions that may fall within the boundaries of the uniform-sized blocks.

Zell, Peter↗
NASA NTRS2017

Vacuum Infusion Process Development for Conformal Ablative Thermal Protection System Materials

Conformal ablators are low density composite materials comprised of a flexible carbon felt based fibrous substrate and a high surface area phenolic matrix. These materials are fabricated to near net shape by molding the substrate, placing in a rigid matched mold and infusing with liquid resin through a vacuum assisted process. The open mold process, originally developed for older rigid substrate ablators, such as PICA, wastes a substantial amount of resin. In this work, a vacuum infusion process a type of liquid composite molding where resin is directly injected into a closed mold under vacuum is advanced for conformal ablators. The process reduces waste over the state-of-the-art technique. Small, flat samples of Conformal Phenolic Impregnated Carbon Ablator are infused using the new approach and subjected to a range of curing configurations and conditions. Resulting materials are inspected for quality and compared to material produced using the standard process. Lessons learned inform subsequent plans for process scale up.

TPS↗
DOE OSTI2023

Physics-Driven Convolutional Autoencoder Approach for CFD Data Compressions: Preprint

With the growing size and complexity of turbulent flow models, data compression approaches are of the utmost importance to analyze, visualize, or restart the simulations. Recently, in-situ autoencoder-based compression approaches have been proposed and shown to be effective at producing reduced representations of turbulent flow data. However, these approaches focus solely on training the model using point-wise sample reconstruction losses that do not take advantage of the physical properties of turbulent flows. In this paper, we show that training autoencoders with additional physics-informed regularizations, e.g., enforcing incompressibility and preserving enstrophy, improves the compression model in three ways: (i) the compressed data better conform to known physics for homogeneous isotropic turbulence without negatively impacting point-wise reconstruction quality, (ii) inspection of the gradients of the trained model uncovers changes to the learned compression mapping that can facilitate the use of explainability techniques, and (iii) as a performance byproduct, training losses are shown to converge up to 12x faster than the baseline model.

auto-encoders↗
DOE OSTI2023

Methods of making lithium ion conducting sulfide glass

A lithium ion-conductive solid electrolyte including a freestanding inorganic vitreous sheet of sulfide-based lithium ion conducting glass is capable of high performance in a lithium metal battery. Such an electrolyte is also manufacturable, and readily adaptable for battery cell and cell component manufacture, in a cost-effective, scalable manner using an automated machine based system, apparatus and methods based on inline spectrophotometry to assess and inspect the quality of such vitreous solid electrolyte sheets and associated components. Suitable manufacturing methods can involve providing a sulfur precursor, providing a boron precursor material having lithium as a second constituent, combining the sulfur and boron precursor materials to form a precursor mixture, melting the mixture, and cooling the melt to form a solid lithium ion conducting glass. The glass may have a Li+ conductivity of at least 10 −5 S/cm. The boron precursor material may be synthesized by reducing boron oxide to boron metal by heating the boron oxide in direct contact with lithium metal.

Visco, Steven J.↗
NASA NTRS1987

Electronic Inspection of Beef

Two proposed methods for grading beef quality based on inspection by electronic equipment: one method uses television camera to generate image of a cut of beef as customer sees it; other uses ultrasonics to inspect live animal or unsliced carcasses. Both methods show promise for automated meat inspection.

Anselmo, Victor J.↗
DOE OSTI2025

A Semi-supervised Hybrid Machine Learning Framework for the Qualification of Resistance Spot Welds

• Industries requiring high structural integrity, including automotive, aerospace, and construction, place considerable significance on weld quality classification. • The inspection normally involves human expertise through predefined quality metrics that are subjective, error-prone, and time-intensive • The challenge to classification model development is the scarcity of labeled data and imbalanced distributions in the data that are labeled. • This work develops a new hybrid methodology that achieves clustering using KMeans++ together with supervised classification to overcome these challenges. • The ensemble-based classifiers were identified as optimal, with accuracy enhancements of up to 8% using the pseudo-labeled dataset. • The work provides practical insight into feature engineering and machine learning integration in industrial quality assurance applications.

Rogers, Jeremy K. [Savannah River National Laborat↗
NASA NTRS1981

The quality assurance role in the Deep Space Network

The quality assurance section provides skilled personnel who perform the following functions: quality hardware engineering, quality software engineering, inspection and testing, and an independent assessment to quality, engineering and project requirements. The quality assurance section provides specifications, workmanship standards, process specifications and quality assurance procedures in support of DSN equipment. In addition, the quality assurance section reviews DSN engineering documents to ensure that appropriate and adequate quality provisions are included.

Sirpilla, R. L.↗
NASA NTRS2009

A Reference Model for Software and System Inspections. White Paper

Software Quality Assurance (SQA) is an important component of the software development process. SQA processes provide assurance that the software products and processes in the project life cycle conform to their specified requirements by planning, enacting, and performing a set of activities to provide adequate confidence that quality is being built into the software. Typical techniques include: (1) Testing (2) Simulation (3) Model checking (4) Symbolic execution (5) Management reviews (6) Technical reviews (7) Inspections (8) Walk-throughs (9) Audits (10) Analysis (complexity analysis, control flow analysis, algorithmic analysis) (11) Formal method Our work over the last few years has resulted in substantial knowledge about SQA techniques, especially the areas of technical reviews and inspections. But can we apply the same QA techniques to the system development process? If yes, what kind of tailoring do we need before applying them in the system engineering context? If not, what types of QA techniques are actually used at system level? And, is there any room for improvement.) After a brief examination of the system engineering literature (especially focused on NASA and DoD guidance) we found that: (1) System and software development process interact with each other at different phases through development life cycle (2) Reviews are emphasized in both system and software development. (Figl.3). For some reviews (e.g. SRR, PDR, CDR), there are both system versions and software versions. (3) Analysis techniques are emphasized (e.g. Fault Tree Analysis, Preliminary Hazard Analysis) and some details are given about how to apply them. (4) Reviews are expected to use the outputs of the analysis techniques. In other words, these particular analyses are usually conducted in preparation for (before) reviews. The goal of our work is to explore the interaction between the Quality Assurance (QA) techniques at the system level and the software level.

He, Lulu↗
NASA NTRS1971

Radiographic inspection specifications for electronic components

Quality assurance provisions cover personnel training, radiographic equipment, radiographic test procedures, and inspection and examination of radiographs. Supplementary information includes accept and reject criteria for radiographic inspection of resistors, capacitors, transistors, hybrid microcircuits, diodes, small coils and transformers.

Source record↗
NASA NTRS1993

(abstract) Formal Inspection Technology Transfer Program

A Formal Inspection Technology Transfer Program, based on the inspection process developed by Michael Fagan at IBM, has been developed at JPL. The goal of this program is to support organizations wishing to use Formal Inspections to improve the quality of software and system level engineering products. The Technology Transfer Program provides start-up materials and assistance to help organizations establish their own Formal Inspection program. The course materials and certified instructors associated with the Technology Transfer Program have proven to be effective in classes taught at other NASA centers as well as at JPL. Formal Inspections (NASA tailored Fagan Inspections) are a set of technical reviews whose objective is to increase quality and reduce the cost of software development by detecting and correcting errors early. A primary feature of inspections is the removal of engineering errors before they amplify into larger and more costly problems downstream in the development process. Note that the word 'inspection' is used differently in software than in a manufacturing context. A Formal Inspection is a front-end quality enhancement technique, rather than a task conducted just prior to product shipment for the purpose of sorting defective systems (manufacturing usage). Formal Inspections are supporting and in agreement with the 'total quality' approach being adopted by many NASA centers.

certified instructors Formal Inspections↗
NASA NTRS2003

Visual and x-ray inspection characteristics of eutectic and lead free assemblies

For high reliability applications, visual inspection has been the key technique for most conventional electronic package assemblies. Now, the use of x-ray technique has become an additional inspection requirement for quality control and detection of unique defects due to manufacturing of advanced electronic array packages such as ball grid array (BGAs) and chip scale packages (CSPs).

x-ray↗
NASA NTRS2019

Assessing Reliability of NDE Flaw Detection Using Smaller Number of Demonstration Data Points

The paper provides an engineering analysis approach for assessing reliability of NDE flaw detection using smaller number of demonstration data points. It explores dependence of probability of detection (POD), probability of false positive (POF), on contrast-to-noise ratio, and net decision threshold-to-noise ratio in a simulated data; and draws some generically applicable inferences to devise the approach. ASTM nondestructive evaluation standards provide requirements on signal-to-noise ratio and/or contrast-to-noise ratio in order to provide reliable flaw detection and limit false positive calls. POD analysis of inspection test data results in an estimated flaw size, denoted by 𝑎90/95. This flaw size has 90% POD and minimum 95% confidence. POF is also estimated in the analysis. POD demonstration requires specimens with flaws of known size. In many situations, it is very expensive to produce the large number of flaws required for the POD analysis. In some situations, only real flaws can truly represent the flaws for demonstration. Real flaws of correct size and location in part configuration specimen may be difficult to produce, if not impossible. Here, an engineering analysis approach is devised using simulation to assess reliability of NDE technique when a limited number of flaws are available for demonstration. In this simulation, a technique is considered reliable, if it provides flaw detectability size equal to or better than the theoretical 𝑎90𝑡ℎ used in simulation and also provides a POF less than or equal to a chosen value. The paper uses simulated signal response versus flaw size data to devise the approach. Linear correlation is used between the signal response data and flaw size. POD software mh1823 uses generalized linear model (GLM) in POD analysis after transforming the flaw size and signal response, if needed, using logarithm. Therefore, this approach is in agreement with the linear signal correlation used in mh1823. Using the POD analysis of data, generic conditions on contrast-to-noise ratio and net decision threshold-to-noise ratio are derived for reliable flaw detection. In order to assess technique reliability using the engineering approach, signal response-to-flaw size correlation about the flaw size of concern is needed. In addition, measurement of noise is also needed. If the technique meets the above requirements, assumption of linear signal-to-flaw size correlation and conditions on noise, then the technique can be assessed using this analysis as it fits the underlying POD model used here. The approach is conservative and is designed to provide a larger flaw size compared to the POD approach. Such NDE technique assessment approach, although, not as rigorous as POD, can be cost effective if the larger flaw size can be tolerated. Typically, this is a situation for all quality control NDE inspections. Here, an NDE technique needs to be reliable and 𝑎90/95 is not estimated, but the assessed flaw size is assumed to be larger than the unknown a90 due to conservative factors or margins. Applicability of the approach for assessing reliability of flaw detection in x-ray radiography and 2D imaging in general is also explored.

Koshti, Ajay M.↗
NASA NTRS1963

PILOT SAFETY AND MERCURY ATLAS

This program to protect the Mercury astronauts - based on quality assurance, intensive inspections, and ASIS - has important future implications.

MANNED SPACECRAFT↗
NASA NTRS1969

Semiautomatic inspection of microfilm records

Semiautomatic machine inspects microfilm for deficiencies. Advantages of microfilm inspector are uniformity of inspection method, increased speed of inspection, and improved quality through elimination of scratches and finger marks.

Klein, E. L.↗
NASA NTRS1976

Modification of Moore measuring machine/Leitz microscope

Quality assurance mechanical inspection, anticipating the need for improved measuring techniques for the various laboratory programs, has perfected a modification of the Leitz microscope for the Moore measuring machine that has the capability of significantly reducing inspection time with increased reliability.

Greth, H. A.↗