Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “polymer melts”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Long-Term Aging in Miscible Polymer Nanocomposites

Here we find that the initial, solvent-cast state of nanoparticles (NPs) in a polymer matrix temporally evolves during thermal annealing such that, at steady state, NPs maximize their distance from each other subject to mass balance constraints. The observed timescales for this unexpected structural reorganization, as probed by small-angle X-ray scattering, are temperature-dependent and can be prohibitively large, especially at temperatures around and below 1.2Tg. X-ray photon correlation spectroscopy measurements during reorganization reveal that the collective NP dynamics slow down with annealing at constant temperature; this is accompanied by changes in the low-frequency regime in macroscopic viscoelastic measurements in equilibrated materials. By ruling out other potential sources for these effects (i.e., electrostatic interactions, adsorbed layers), we attribute these results to a long-ranged repulsive force between the NPs caused by fluctuations in the polymer phase, i.e., the "anti-Casimir" effect proposed by Obhukhov and Semenov [Long-range interactions in polymer melts: The anti-Casimir effect. Phys Rev Lett 2005, 95 (3), 038305]. Thus, our results highlight the important role of long-term, slow NP reorganization on the structure and, subsequently, the properties of polymer nanocomposites (PNCs), even in the case of nominally miscible polymer nanoparticle hybrids.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Nonlinear Shear Rheology of Entangled Polymer Rings

Steady-state shear viscosity η($\bar{γ}$) of unconcatenated ring polymer melts as a function of the shear rate $\bar{γ}$ is studied by a combination of experiments, simulations, and theory. Experiments using polystyrenes with Z ≈ 5 and Z ≈ 11 entanglements indicate weaker shear thinning for rings compared to linear polymers exhibiting power law scaling of shear viscosity η ~ $\bar{γ}$ –0.56 ± 0.02 , independent of chain length, for Weissenberg numbers up to about 10 2 . Nonequilibrium molecular dynamics simulations using the bead-spring model reveal a similar behavior with η ~ $\bar{γ}$ -0.57 ± 0.08 for 4 ≤ Z ≤ 57. Viscosity decreases with chain length for high $\bar{γ}$. In our experiments, we see the onset of this regime, and in simulations, which we extended to Wi ~ 10 4 , the nonuniversality is fully developed. In addition to a naive scaling theory yielding for the universal regime η ~ $\bar{γ}$ –0.57 , we developed a novel shear slit model explaining many details of observed conformations and dynamics as well as the chain length-dependent behavior of viscosity at large $\bar{γ}$. The signature feature of the model is the presence of two distinct length scales: the size of tension blobs and much larger thickness of a shear slit in which rings are self-consistently confined in the velocity gradient direction and which is dictated by the size of a chain section with relaxation time 1/$\bar{γ}$. These two length scales control the two normal stress differences. In this model, the chain length-dependent onset of nonuniversal behavior is set by tension blobs becoming as small as about one Kuhn segment. This model explains the approximate applicability of the Cox–Merz rule for ring polymers.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Decoding polymer self-dynamics using a two-step approach

The self-correlation function and corresponding self-intermediate scattering function in Fourier space are important quantities for describing the molecular motions of liquids. This work draws attention to a largely overlooked issue concerning the analysis of these space-time density-density correlation functions of polymers. Here, we show that the interpretation of non-Gaussian behavior of polymers is generally complicated by intrachain averaging of distinct self-dynamics of different segments. By the very nature of the mathematics involved, the averaging process not only conceals critical dynamical information, but also contributes to the observed non-Gaussian dynamics. To fully expose this issue and provide a thorough benchmark of polymer self-dynamics, we perform analyses of coarse-grained molecular dynamics simulations of linear and ring polymer melts as well as several theoretical models using a “two-step” approach, where interchain and intrachain averagings of segmental self-dynamics are separated. While past investigations primarily focused on the average behavior, our results indicate that a more nuanced approach to polymer self-dynamics is clearly required.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Probing Nanorod Assembly and Dynamics in Polymer Nanocomposites in Equilibrium and Shear

Coarse-grained molecular dynamics simulations are used to examine the structure and dynamics of nanorod assemblies in polymer melts under equilibrium and simple shear. We show that as the concentration of nanorods increases, there is a transition from an isotropic phase to a two-phase region in which the nanorods phase separate into a dilute phase and dense bundles of hexagonally packed nanorods. The onset of the two-phase region is below that predicted by Onsager theory, which we attribute to an effective increase in the diameter of nanorods due to a layer of polymer bound to the rod surfaces. Equilibrium simulations show that increasing polymer chain length N enhances nanorod bundling at fixed nanorod concentration. Simulations of systems undergoing simple shear show that flow enhances nanorod alignment and bundling relative to those of equilibrium systems with similar properties. Finally, simulations reveal that increasing nanorod length enhances nanorod alignment under shear at equivalent shear rates but not at equivalent Péclet numbers. Overall, our simulations highlight that polymer matrix-nanorod attraction (i.e., chemistry), shear rate, and matrix chain length are desirable design variables to control the structure of nanorod-containing soft materials under simple shear.

diffusion↗
DOE OSTI2020

Microstructural characterization of a star-linear polymer blend under shear flow by using rheo-SANS

We present an investigation into the dynamic relaxation mechanisms of a polybutadiene blend composed of a four-arm star (10 wt. %) and a linear polymer matrix in the presence of an applied shear flow. Our focus was the response of the star polymer, which cannot be unambiguously assessed via linear viscoelastic measurements since the signature of the star polymer can barely be detected due to the dominant contribution of the linear matrix. By utilizing small-angle neutron scattering (SANS) coupled with a Couette shear device and a deuterated matrix polymer, we investigated the dynamics of the minority star component of the blend. Our results confirm that the stars deform anisotropically with increasing shear rate. We have compared the SANS data with predictions from the well-established scattering adaptation of the state-of-the-art tube model for entangled linear polymer melts undergoing shear, i.e., Graham, Likhtman, Milner, and McLeish (GLaMM) approach, appropriately modified following earlier studies in order to apply to the star. This modified model, GLaMM-R, includes the physics necessary to understand stress relaxation in both the linear and nonlinear flow regimes, i.e., contour length fluctuations, constraint release, convective constraint release, and chain retraction. The full scattering signal is due to the minority star component and, although the contribution of the linear chains is hidden from the neutron scattering, they still influence the star polymer molecular dynamics, with the applied shear rate ranging from approximately 8 to 24 s –1 , below the inverse relaxation time of the linear component. This study provides another confirmation that the combination of rheology and neutron scattering is an indispensable tool for investigating the nonlinear dynamics of complex polymeric systems.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Dynamic density functional theory of polymers with salt in electric fields

Here we present a dynamic density functional theory for modeling the effects of applied electric fields on the local structure of polymers with added salt (polymer electrolytes). Time-dependent equations for the local electrostatic potential and volume fractions of polymer, cation, and anion of added salt are developed using the principles of linear irreversible thermodynamics. For such a development, a field theoretic description of the free energy of polymer melts doped with salts is used, which captures the effects of local variations in the dielectric function. Connections of the dynamic density functional theory with experiments are established by relating the three phenomenological Onsager’s transport coefficients of the theory to the mutual diffusion of electrolyte, ionic conductivity, and transference number of one of the ions. The theory is connected with a statistical mechanical model developed by Bearman and Kirkwood [J. Chem. Phys. 28, 136 (1958)] after relating the three transport coefficients to friction coefficients. The steady-state limit of the dynamic density functional theory is used to understand the effects of dielectric inhomogeneity on the phase separation in polymer electrolytes. The theory developed here provides not only a way to connect with experiments but also to develop multi-scale models for studying connections between local structure and ion transport in polymer electrolytes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2026

Impact of Small-Alkane Solvents on Polyolefin Hydrogenolysis over a Ruthenium Catalyst

Selective catalytic hydrogenolysis of polyolefins is a promising route to convert plastic waste into valuable liquid products, such as lubricants, waxes, and surfactants. However, the high viscosity of polymer melts imposes mass transfer limitations on this reaction. Solvents can mitigate these challenges, but their effects on reaction kinetics and product selectivity remain underexplored. Here, we systematically explore the effects of small n-alkanes and cycloalkanes on the hydrogenolysis of polyethylene and polypropylene over a Ru/TiO 2 catalyst. Using kinetic measurements and isotopic labeling, we show that n-octane at high mass fractions alters the mechanism from direct hydrogenation to solvent-mediated hydrogen transfer, reducing the rate of C–C bond cleavage. Longer alkanes further inhibit reactivity due to stronger surface binding. 1,4-Dimethylcyclohexane suppresses methane formation, favoring heavier products, while decalin likely forms surface-bound aromatics that poison the catalyst. Overall, alkane solvents modulate product selectivity and reduce the yield of methane byproduct, allowing for ∼35–40% selectivity to valuable C 20 -C 30 alkane products. This work highlights the complex impact of polymer–alkane mixtures on hydrogenolysis kinetics relevant to the design of commercial-scale plastic waste valorization processes.

Catalysts↗
DOE OSTI2024

Utilization of Ultrasonication as a Method of Reducing Organic and Inorganic Contamination in Post‐Consumer Plastic Film Waste

Post-consumer plastic film waste often carries organic and inorganic contaminants that challenge recycling processes and affect the quality of recycled products. An effective contaminant removal procedure through washing such single-used plastic films (SUPFs) can address environmental and waste management concerns. This study compares the efficiency of different washing techniques in reducing SUPF contamination. To evaluate the efficacy of each washing technique, film samples collected from material recovery facilities are individually exposed to friction, ultrasonic-assisted, and a combination of both washes. Thermal analysis indicates that the polymers' melting temperature, crystallization temperature, and crystallinity remain unaffected by the washing methods, demonstrating method aptness. Confocal laser scanning microscope images show that washing results in a cleaner sample surface. 91% ash reduction during the combined wash treatment indicates a high method efficiency compared to the individual friction and ultrasonic wash procedures. This is further validated by reducing characteristic contaminant IR bands (3600–3000, 1750–1600, and 1100–1000 cm −1 ). Elements of concern such as Cd, Cr, Hg, and Pb in SUPFs after each washing technique applied conform with regulations (<100 ppm) for packaging products. This research shows the novel ultrasonic washing reduces more contamination than friction with shorter wash times and no surfactants.

42 ENGINEERING↗
DOE OSTI2023

Assembly of Arbitrary Designer Heterostructures with Atomically Clean Interfaces

Van der Waals heterostructures are an excellent platform for studying intriguing interface phenomena, such as moiré and proximity effects. Many of these phenomena occurring in such heterostructures' interfaces and surfaces have so far been hampered because of their high sensitivity to disorder and interface contamination. Here, it reports a dry polymer-based assembly technique to fabricate arbitrary designer van der Waals heterostructures with atomically clean surfaces. The key features of the suspended dry pick-up and flip-over assembly technique are: 1) the heterostructure surface never comes into contact with polymers, 2) the assemble is entirely solvent-free, 3) it is entirely performed in a glovebox, and 4) it only requires temperatures below 130 °C. By performing ambient atomic force microscopy and atomically-resolved scanning tunneling microscopy on example heterostructures, it demonstrates the fabrication of air-sensitive heterostructures with ultra-clean interfaces and surfaces. It envisions that, due to the avoidance of polymer melting, this technique is potentially compatible with heterostructure assembly under ultra-high vacuum conditions, which promises ultimate heterostructure quality.

2D materials↗
DOE OSTI2024

In Situ Alloying Enabled by Active Liquid Metal Filler for Self‐Healing Composite Polymer Electrolytes

Abstract Solid inorganics, known for kinetically inhibiting polymer crystallization and enhancing ionic conductivity, have attracted significant attention in solid polymer electrolytes. However, current composite polymer electrolytes (CPEs) are still facing challenges in Li metal batteries, falling short of inhibiting severe dendritic growth and resulting in very limited cycling life. This study introduces Ga 62.5 In 21.5 Sn 16 (Galinstan) liquid metal (LM) as an active liquid alternative to conventional passive solid fillers, aiming at realizing self‐healing protection against dendrite problems. Compared to solid inorganics, for example silica, LM droplets could more significantly reduce polymer crystallinity and enhance Li‐ion conductivity due to their liquid nature, especially at temperatures below the polymer melting point. More importantly, LMs are unraveled as dynamic chemical traps, which are capable of blocking and consuming lithium dendrites upon contact via in situ alloying during battery operation and further inhibiting dendritic growth due to the lower deposition energy barrier of the formed Li‐LM alloy. As a proof of concept, by strategically designing an asymmetric CPE with the active LM filling, a solid‐state Li/LiFePO 4 battery achieves promising full‐cell functionality with notable rate performance and stable cycle life. This active filler‐mediated self‐healing approach could bring new insights into the battery design in versatile solid‐state systems.

Wu, Kai↗
DOE OSTI2024

Rheology characterization of ionic liquids under high pressure and high temperature

Ionic liquids (ILs) are liquid salts that exist at or below ambient temperatures and are composed of ion pairs. They offer promising alternatives to toxic, hazardous, highly flammable, and volatile solvents in various applications such as solution preparation, dispersion, gel formation, composites, and polymer melts. ILs possess unique and interesting characteristics, including excellent chemical and thermal stability and low vapor pressures. Understanding the rheological properties of ILs is essential to optimizing IL performance. This paper presents a comparative analysis of the rheological properties of two ionic liquids, Nsingle bondHexylpyridinium tetrafluoroborate (HPyBF4) and Nsingle bondHexylpyridinium bromide (HPyBr), under different shear rates, temperatures, and pressures. Rheological measurements were performed under varying controlled pressure and temperature conditions. The experimental investigation covered a pressure range of 689–12,411 kPa [100–1800 psi] and a temperature range from room temperature up to 522 kelvin (K) [480°F]. The primary objective is to explore and compare the flow behavior and viscoelastic characteristics of HPyBF4 and HPyBr under high-pressure and high-temperature conditions. The experimental data showed that HPyBF4 and HPyBr exhibited shear-thinning behavior, and pressure had an insignificant effect on rheology compared to the temperature effect. Under the same testing conditions, HPyBr showed higher shear stress and viscosity than HPyBF4. This research significantly contributes to the improved understanding of the rheological behavior of these specific ionic liquids and their suitability for diverse industrial and scientific applications, particularly in high-pressure and high-temperature environments.

15 GEOTHERMAL ENERGY↗
DOE OSTI2026

A Bayesian desmearing algorithm for Bonse–Hart USANS with anisotropic scattering

Ultra-small-angle neutron scattering (USANS) using Bonse–Hart optics provides micrometer-scale structural insights but suffers from severe slit-geometry smearing. While well-established for isotropic systems, quantitative desmearing of anisotropic data remains a challenge because conventional corrections break down for non-radial scattering. In this work, we address this by developing a resolution-aware Bayesian framework that explicitly incorporates anisotropy via an affine deformation to the scattering pattern, guided by the principle of parsimony. This results in orientation-resolved point-spread functions that enable a self-consistent determination of both the resolution and deformation parameters. Using Gaussian process regression with uncertainty quantification and a probabilistic correction for multiple scattering, we demonstrate the framework’s effectiveness through numerical benchmarks and experimental studies of a stretched polymer melt. Our approach enables the seamless integration of SANS and USANS data, facilitating quantitative structural analysis of deformed materials at nanometer to micrometer scales.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Learning unknown physics of non-Newtonian fluids

Here, we use physics-informed neural networks (PINNs) to learn viscosity models of two non-Newtonian systems (polymer melts and suspensions of particles) using only velocity measurements. For synthetic velocity data generated with the power-law viscosity model, the PINN-inferred viscosity model agrees with the analytical model for shear rates with large absolute values but deviates for shear rates near zero where the analytical model has an unphysical singularity. Once the viscosity model is learned the PINN method can solve the momentum conservation equation using only the boundary conditions.

42 ENGINEERING↗
DOE OSTI2020

Absolute intensity calibration for carbon-edge soft X-ray scattering

Resonant soft X-ray scattering (RSOXS) has become a premier probe to study complex three-dimensional nanostructures in soft matter through combining the robust structural characterization of small-angle scattering with the chemical sensitivity of spectroscopy. This technique borrows many of its analysis methods from alternative small-angle scattering measurements that utilize contrast variation, but thus far RSOXS has been unable to reliably achieve an absolute scattering intensity required for quantitative analysis of domain compositions, volume fraction, or interfacial structure. Here, a novel technique to calibrate RSOXS to an absolute intensity at the carbon absorption edge is introduced. It is shown that the X-ray fluorescence from a thin polymer film can be utilized as an angle-independent scattering standard. Verification of absolute intensity is then accomplished through measuring the Flory–Huggins interaction parameter in a phase-mixed polymer melt. As a result, the necessary steps for users to reproduce this intensity calibration in their own experiments to improve the scientific output from RSOXS measurements are discussed.

47 OTHER INSTRUMENTATION↗
DOE OSTI2024

Experimental and statistical study on the effect of process parameters on the quality of continuous fiber composites made via additive manufacturing

Ongoing research in additive manufacturing towards structural and industrial application has led to the use of commingled roving as a manufacturing feedstock for printing high fiber volume fraction composites. The prospects of using this technology for high performance applications necessitates the need for a comprehensive experimental investigation into the effects of processing parameters on the quality of an additively manufactured composite printed from commingled roving feedstock. Here, in this work, transverse flexure and void fraction matrix pyrolysis testing are both performed to evaluate composite quality. The transverse flexure test is a testing approach that evaluates the quality of the interfacial fiber-matrix bond while the void fraction test estimates the void content in the printed composite. A full observational study consisting of 27 different test combinations is done to investigate the effects of three different process parameters namely, temperature, pressure, and print speed across three different levels. Composite samples were made from commingled roving of E-glass and amorphous PET using an in-house built continuous fiber composite digital manufacturing system. Least squares regression analysis is performed to study the main, interaction and quadratic effects of process parameters. A statistical regression model having an R2 adjusted value of 80.1% is generated from the transverse flexure study, which is used to explain main and interaction effects and also predict performance. Response surface plots are also generated and are used to optimize process parameters which can subsequently be of help in scaling up composite manufacturing. Results show that all three process parameters are highly statistically significant at the 0.01 level of significance. Pressure * Temperature and Pressure * Printspeed are significant interaction terms. Pressure plays a weightier role when print speed is increased or temperature is decreased as it closes more voids that would ordinarily have been introduced because of drop in polymer melt viscosity. Micrographic analysis is also performed.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Additively Manufactured Carbon Fiber-Reinforced Siliconized Silicon Carbide Composites Using Carbon Fiber-Reinforced Poly-Ether-Ether-Ketone (PEEK) as a Precursor

Herein, we report a method to additively manufacture carbon fiber-reinforced siliconized silicon carbide composites. The process involves the pyrolysis of a 3D-printed carbon fiber-reinforced poly-ether-ether-ketone (PEEK) composite to produce a porous carbon fiber-reinforced carbon matrix composite preform, which is subsequently infiltrated with molten silicon to obtain a carbon fiber-reinforced siliconized silicon carbide composite. A key aspect of the method is limiting polymer melt flow during pyrolysis of PEEK, which is achieved by thermally annealing the 3D-printed carbon fiber-reinforced PEEK preform in air at a temperature below PEEK’s melting temperature. Rheological and differential scanning calorimetry (DSC) measurements demonstrate that the thermal annealing treatment altered the melting behavior of PEEK, while NMR and FTIR measurements provided a mechanistic explanation for the structural changes responsible for the behavior. It was also found that dimensional changes during pyrolysis were anisotropic with greater shrinkage in the stacking direction of the material.

Yoon, Bola [ORNL] (ORCID:0000000260875373)↗
DOE OSTI2024

The melt memory effects in polymer crystallization

This paper presents a systematic review of the literature on the melt memory effects observed in polymers, an area that has engendered considerable debate for over 50 years. Recent advances in experimental techniques have provided fresh insights into how a polymer's thermal history influences its recrystallization behavior. It has been observed that given other conditions unchanged, the crystallization temperature during recrystallization decreases with an increase in the melt temperature T s above the melting point T m until a critical melt temperature is attained. This phenomenon also extends to the half-time of crystallization and the secondary structures, such as lamellar thickness, of semi-crystalline polymers. Despite these findings, a comprehensive constitutive model that encapsulates polymer melt memory effects remains elusive. Cutting-edge instrumentation, including in situ small and wide-angle X-ray scattering, temperature-controlled Fourier transform infrared spectroscopy, and flash differential scanning calorimetry, have posed significant challenges to the traditional nucleation and growth models established in the 1970s. These models are foundational to our understanding of polymer crystallization, which is an integral part of polymer processing and production. In this review, the historical contours of this discourse are traced, with an examination of both the recent experimental breakthroughs and theoretical advancements pertinent to polymer melt memory effects. In conclusion, this paper delves into the prevailing theories of polymer nucleation and crystallization and engages with theoretical discussions and numerical simulations that attempt to elucidate and rationalize these melt memory phenomena.

36 MATERIALS SCIENCE↗