Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plastic deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A spatially-resolved model of neutron-irradiated tungsten coupling stochastic cluster dynamics and finite deformation plasticity

Structural materials used in nuclear reactors face severe degradation in mechanical properties, such as hardening and embrittlement. At the microscopic scale, this occurs due to creation and accumulation of irradiation-induced defects and their interaction with system dislocations. Although techniques exist which can model evolution of irradiation defects, for instance kinetic transport theory-based models, their interaction with mechanical deformation of the bulk material has not been investigated extensively. In this work, we demonstrate a novel spatially-resolved multiscale coupling between microscopic irradiation defect evolution, modeled using Stochastic Cluster Dynamics (SCD) and macroscopic mechanical deformation modeled using a finite-deformation plasticity model. SCD is used to determine the statistically averaged defect cluster spacing, dependent on operating conditions such as irradiation dose and temperature. This acts as an initial condition that governs the critical resolved shear stress of dislocation glide in the macroscopic plasticity model. This framework is used to predict mechanical behavior in post-mortem test of irradiated Tungsten samples, which has found its importance as structural material used in nuclear reactors. The results obtained using the coupled approach are in good agreement with experimental data of uniaxial tension tests. The model is able to capture the effect of temperature and irradiation dose on the material hardening. Two methods are proposed to estimate hardness – using Tabor's Law relating uniaxial yield stress to hardness and from flat-punch simulations. The results are in reasonable agreement with hardness data from micro-indentation experiments of irradiated Tungsten samples. Finally, the model is also able to reveal microstructural details such as spatial variation in defect density and local stress.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2022

Assessment of diffuse-interface methods for compressible multiphase fluid flows and elastic-plastic deformation in solids

This work describes three diffuse-interface methods for the simulation of immiscible, compressible multiphase fluid flows and elastic-plastic deformation in solids. The first method is the localized-artificial-diffusivity approach of Cook, Subramaniam et al., and Adler and Lele, in which artificial diffusion terms are added to the individual phase mass fraction transport equations and are coupled with the other conservation equations. The second method is the gradient-form approach that is based on the quasi-conservative method of Shukla et al., in which the diffusion and sharpening terms (together called regularization terms) are added to the individual phase volume fraction transport equations and are coupled with the other conservation equations. The third approach is the divergence-form approach that is based on the fully conservative method of Jain et al., in which the regularization terms are added to the individual phase volume fraction transport equations and are coupled with the other conservation equations. In the present study, all three diffuse-interface methods are used in conjunction with a four-equation, multicomponent mixture model, in which pressure and temperature equilibria are assumed among the various phases. The primary objective of this work is to compare these three methods in terms of their ability to: maintain constant interface thickness throughout the simulation; conserve mass, momentum, and energy; and maintain accurate interface shape for long-time integration. The second objective of this work is to consistently extend these methods to model interfaces between solid materials with strength. To assess and compare the methods, they are used to simulate a wide variety of problems, including (1) advection of an air bubble in water, (2) shock interaction with a helium bubble in air, (3) shock interaction and the collapse of an air bubble in water, and (4) Richtmyer–Meshkov instability of a copper–aluminum interface. The current work focuses on comparing these methods in the limit of relatively coarse grid resolution, which illustrates the true performance of these methods. In conclusion, this is because it is rarely practical to use hundreds of grid points to resolve a single bubble or drop in large-scale simulations of engineering interest.

97 MATHEMATICS AND COMPUTING↗
DOE OSTI2023

Half-hard copper PTW model parameters for plastic deformation calibrated to strain rates from 10 −3 -10 7 /s

This document demonstrates a calibration of the Preston-Tonks-Wallace (PTW) model of plastic deformation that fairly accurately reproduces the flow stress of half-hard copper across strain rates varying by a factor of more than ten billion. The experiments included are quasistatic compression at low rates, Split Hopkinson Pressure Bar (SHPB) compression at intermediate rates, and arrested Richtmyer-Meshkov instability (RMI) growth at high strain rates. The temperatures vary from liquid nitrogen (77 K) to around 500 K. The largest true strains obtained are approximately 0.5. It would be interesting to compare the results to copper deformation data at higher pressures and higher strains.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Effect of free surfaces on localized plastic deformation in single-crystal nickel containing helium bubbles and radiation-induced self-interstitial atom clusters

This paper presents molecular dynamics (MD) simulations of plastic deformation in single-crystal Ni models containing internal distributions of helium (He) bubbles and self-interstitial atom (SIA) clusters corresponding to experimental characterization of ex-service Inconel X-750 components. Here, we simulate single crystals with and without free surfaces at room temperature and 588K, the latter temperature corresponding to the Inconel X-750 service conditions. Both models are deformed under multiple slip to a maximum deviatoric strain of ~10 %. A dislocation slip band forms in the model without free surfaces, but not in the model with free surfaces. However, the latter exhibits nano-twin nucleation from surfaces. Helium (He) bubbles that overlap with a slip band or a nano-twinned region deform more severely than other bubbles in the model. Nevertheless, the bubbles do not link up and do not form configurations that resemble incipient cracks.

36 MATERIALS SCIENCE↗
NASA NTRS2010

Comparative Analysis of the Effects of Severe Plastic Deformation and Thermomechanical Training on the Functional Stability of Ti50.5Ni24.5Pd25 High-Temperature Shape Memory Alloy

We compare the effectiveness of a conventional thermomechanical training procedure and severe plastic deformation via equal channel angular extrusion to achieve improved functional stability in a Ti50.5Ni24.5Pd25 high-temperature shape memory alloy. Thermomechanical testing indicates that both methods result in enhanced shape memory characteristics, such as reduced irrecoverable strain and thermal hysteresis. The mechanisms responsible for the improvements are discussed in light of microstructural findings from transmission electron microscopy.

Atli, K. C.↗
NASA NTRS2011

Shape Memory Characteristics of Ti(sub 49.5)Ni(sub 25)Pd(sub 25)Sc(sub 0.5) High-Temperature Shape Memory Alloy After Severe Plastic Deformation

A Ti(49.5)Ni25Pd25Sc(0.5) high-temperature shape memory alloy is thermomechanically processed to obtain enhanced shape-memory characteristics: in particular, dimensional stability upon repeated thermal cycles under constant loads. This is accomplished using severe plastic deformation via equal channel angular extrusion (ECAE) and post-processing annealing heat treatments. The results of the thermomechanical experiments reveal that the processed materials display enhanced shape memory response, exhibiting higher recoverable transformation and reduced irrecoverable strain levels upon thermal cycling compared with the unprocessed material. This improvement is attributed to the increased strength and resistance of the material against defect generation upon phase transformation as a result of the microstructural refinement due to the ECAE process, as supported by the electron microscopy observations.

Atli, K. C.↗
NASA NTRS1990

Pinning, flow and plastic deformation of flux vortices in high T(sub c) superconductors

In high temperature superconductor (HTSC) materials the vortices are highly mobile and flexible. This is reflected in different models of melt of a vortex lattice. Another aspect of the problem is stressed: an easy nucleation and high mobility of dislocations in the vortex lattice. Some models of plastic deformation of vortex lattice are considered as a result of its interaction with a real crystal structure. Depinning is interpreted as yield of plastic flow is vortex medium. Effect of macroscopic defects in crystal structures (pores, inclusions, grain and domain boundaries) is being considered in detail. Available experimental facts on magnetization and a critical current in HTSC and conventional superconductors are discussed from the points of view of depinning to vortices vs. plastic flow of vortices vs. plastic flow of vortices medium.

Roytburd, A.↗
NASA NTRS1986

The mechanics of solids in the plastically-deformable state

The mechanics of continua, which is based on the general stress model of Cauchy, up to the present has almost exclusively been applied to liquid and solid elastic bodies. Saint-Venant has developed a theory for the plastic or remaining form changes of solids, but it does not give the required number of equations for determining motion. A complete set of equations of motion for plastic deformable bodies is derived. This is done within the framework of Cauch mechanics. And it is supported by certain experimental facts which characterize the range of applications.

Mises, R. V.↗
DOE OSTI2026

Microstructural Engineering of Cu-Rich Nanoprecipitate formation in NiCoFeCrCu0.12 High-Entropy Alloy via Severe Plastic Deformation for Enhanced Irradiation Tolerance

This study demonstrates a defect-engineering approach for controlling Cu-rich precipitates in FeNiCrCoCu0.2 high-entropy alloys (Cu-HEAs), delivering a novel pathway for next-generation nuclear reactor materials with superior irradiation resistance. This work establishes that severe plastic deformation (SPD) processing via Shear Assisted Processing and Extrusion (ShAPE) and Friction Stir Layer Deposition (FSLD) creates dense dislocation networks and subgrain boundaries that fundamentally alter precipitation behavior under identical thermal treatments. Atom probe tomography (APT) indicates that SPD produces a metastable, atomically homogeneous solid solution that, upon moderate heat treatment (500°C/10 hour), develops remarkedly stronger Cu clustering than the as-cast counterpart. High-temperature exposure (800°C/100 h) produces near-pure Cu precipitates (~90 at% Cu) with significantly enhanced defect-sink efficacy in SPD-processed alloys: precipitate sizes of 50-60 nm and number densities of 2.7-3.8 × 10¹7 m?³, compared to 89 nm and 0.44 × 10¹7 m?³ in as-cast materials. Collectively, the findings establish defect-mediated precipitation control as a scalable, high-impact route to tailor sink density and distribution in HEAs, enabling microstructures optimized for irradiation tolerance and mechanical robustness in nuclear reactor environments.

Meher, Subhashish↗
NASA NTRS1973

Role of plastic deformation in wear of copper and copper - 10-percent-aluminum alloy in cryogenic fuels

High-purity copper specimens and a copper-aluminum (10%) alloy specimen were subjected to sliding against Type 440 C in cryogenic fuel environments. It was found that virtually all wear occurred by the plastic deformation of a recrystallized layer extending to about 10 micrometers below the wear scar surface of the copper or copper alloy. The wear debris was in the form of a layered structure adhering to the exit region of the wear scar. Measurements on the high purity copper specimens indicated that the wear rate was proportional to the applied load and to the sliding velocity squared. A physical model of the wear process is proposed to account for these observations.

Bill, R. C.↗
NASA NTRS1990

Plastic deformation mechanisms in polyimide resins and their semi-interpenetrating networks

High-performance thermoset resins and composites are critical to the future growth of space, aircraft, and defense industries in the USA. However, the processing-structure-property relationships in these materials remain poorly understood. In the present ASEE/NASA Summer Research Program, the plastic deformation modes and toughening mechanisms in single-phase and multiphase thermoset resins were investigated. Both thermoplastic and thermoset polyimide resins and their interpenetrating networks (IPNs and semi-IPNs) were included. The fundamental tendency to undergo strain localization (crazing and shear banding) as opposed to a more diffuse (or homogeneous) deformation in these polymers were evaluated. Other possible toughening mechanisms in multiphase thermoset resins were also examined. The topological features of network chain configuration/conformation and the multiplicity of phase morphology in INPs and semi-IPNs provide unprecedented opportunities for studying the toughening mechanisms in multiphase thermoset polymers and their fiber composites.

Jang, Bor Z.↗
DOE OSTI2021

Textured Electrodes: Manipulating Built-In Crystallographic Heterogeneity of Metal Electrodes via Severe Plastic Deformation

Control of crystallography of metal electrodeposit films has recently emerged as a key to achieving long operating lifetimes in next-generation batteries. It is reported that the large crystallographic heterogeneity, e.g., broad orientational distribution, that appears characteristic of commercial metal foils, results in rough morphology upon plating/stripping. On this basis, an accumulative roll bonding (ARB) methodology—a severe plastic deformation process—is developed. Zn metal is used as a first example to interrogate the concept. It is demonstrated that the ARB process is highly effective in achieving uniform crystallographic control on macroscopic materials. After the ARB process, the Zn grains exhibit a strong (002) texture (i.e., [002] Zn //ND). The texture transitions from a classical bipolar pattern to a nonclassical unipolar pattern under large nominal strain eliminate the orientational heterogeneity of the foil. The strongly (002)-textured Zn remarkably improves the plating/stripping performance by nearly two orders of magnitude under practical conditions. The performance improvements are readily scaled to achieve pouch-type full batteries that deliver exceptional reversibility. The ARB process can, in principle, be applied to any metal chemistry to achieve similar crystallographic uniformity, provided the appropriate temperature and accumulated strains are employed. Here this concept is evaluated using commercial Li and Na foils, which, unlike Zn (HCP), are BCC crystals. The simple process for creating strong textures in both hexagonal and cubic metals and illustrating the critical role such built-in crystallography plays underscores opportunities for developing highly reversible thin metal anodes (e.g., hexagonal Zn, Mg, and cubic Li, Na, Ca, Al).

36 MATERIALS SCIENCE↗
DOE OSTI2020

Atomistic Study of the Plastic Deformation of Transition Metals and High Entropy Alloys (Final Report)

The overarching goal of the research performed in the studies supported by the DOE Basic Energy Sciences has been investigation of mechanical properties of materials employed in technologies related to energy production and conversion using atomic level computer modeling. The materials studied are body-centered-cubic (BCC) transition metals, including α-iron, their alloys and most recently also compositionally complex, so called high entropy alloys (HEAs), which are believed to become future materials in high temperature applications. The goal of the research has been to achieve atomic level understanding of the deformation and fracture of these materials starting from the electronic structure, coarse grain the material energetics into potentials describing interaction between atoms and proceed via atomistic modeling and mesoscopic models to investigation of the glide of dislocations and thus advance the theory of plastic deformation of studied materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Comparison of cracking behavior of nanocrystalline Cu film on substrates of different plastic deformation mechanisms

Nanocrystalline (NC) metallic thin films on metal substrates usually undergo substantial cracking at applied strains of a few percent due to strain concentration at the film/substrate interfaces. In this work, we show that the cracking of a nanocrystalline Cu film can be significantly inhibited by a NiTi substrate. NC Cu films are deposited on 304 stainless steel, Kapton and NiTi substrates, in which plastic deformation occurs via dislocation slip, molecule chain disentanglement and collective lattice shear, respectively. NC Cu film on NiTi substrate starts to show observable cracks at an applied strain of 24%, in contrast to 6% for that on steel and 15% for that on Kapton. Further, the crack density in the film on NiTi substrate is two to three orders lower than the counterparts. The discrepancy is suggested to attribute to the reduced local strain concentration enabled by the uniform lattice shear and high strain hardening of the NiTi substrate.

36 MATERIALS SCIENCE↗
NASA NTRS1985

The effect of carbon concentration and plastic deformation on ultrasonic higher order elastic properties of steel

The behavior of higher order elastic properties, which are much more sensitive to material state than are second order properties, has been studied for steel alloys AISI 1016, 1045, 1095, and 8620 by measuring the stress derivative of the acoustic natural velocity to determine the stress acoustic constants (SAC's). Results of these tests show a 20 percent linear variation of SAC's with carbon content as well as even larger variations with prestrain (plastic deformation). The use of higher order elastic characterization permits quantitative evaluation of solids and may prove useful in studies of fatigue and fracture.

Heyman, J. S.↗
NASA NTRS1974

Finite element formulations for problems of large elastic-plastic deformation

An Eulerian finite element formulation is presented for problems of large elastic-plastic flow. The method is based on Hill's variational principle for incremental deformations, and is suited to isotropically hardening Prandtl-Reuss materials. The formulation is given in a manner which allows any conventional finite element program, for "small strain" elasticplastic analysis, to be simply and rigorously adapted to problems involving arbitrary amounts of deformation and arbitrary levels of stress in comparison to plastic deformation moduli. The method is applied to a necking bifurcation analysis of a bar in plane-strain tension. A unified general formulation of finite element equations, both Lagrangian and Eulerian, for large deformations, with arbitrary choice of the conjugate stress and strain measures, and a discussion is given of other proposed formulations for elastic-plastic finite element analysis at large strain.

Mcmeeking, R. M.↗
NASA NTRS1974

Finite elasto-plastic deformation. I - Theory and numerical examples

It is demonstrated that the problem of elasto-plastic finite deformation is governed by a quasi-linear model irrespective of deformation magnitude. This feature follows from the adoption of a rate viewpoint toward finite deformation analysis in an Eulerian reference frame. Objectivity of the formulation is preserved by introduction of a frame-invariant stress rate. Equations for piece-wise linear incremental finite element analysis are developed by application of the Galerkin method to the instantaneously linear governing differential equations of the quasi-linear model. Numerical solution capability has been established for problems of plane strain and plane stress. The accuracy of the numerical analysis is demonstrated by consideration of a number of problems of homogeneous finite deformation admitting comparative analytic solution. It is shown that accurate, objective numerical solutions can be obtained for problems involving dimensional changes of an order of magnitude and rotations of a full radian.

Osias, J. R.↗
NASA NTRS1975

Finite-element formulations for problems of large elastic-plastic deformation

An Eulerian finite element formulation is presented for problems of large elastic-plastic flow. The method is based on Hill's variational principle for incremental deformations, and is ideally suited to isotropically hardening Prandtl-Reuss materials. Further, the formulation is given in a manner which allows any conventional finite element program, for 'small strain' elastic-plastic analysis, to be simply and rigorously adapted to problems involving arbitrary amounts of deformation and arbitrary levels of stress in comparison to plastic deformation moduli. The method is applied to a necking bifurcation analysis of a bar in plane-strain tension. The paper closes with a unified general formulation of finite element equations, both Lagrangian and Eulerian, for large deformations, with arbitrary choice of the conjugate stress and strain measures. Further, a discussion is given of other proposed formulations for elastic-plastic finite element analysis at large strain, and the inadequacies of some of these are commented upon.

Mcmeeking, R. M.↗