Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “planar transformer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

Diffraction of a shock wave by a compression corner. I - Regular reflection

The unsteady, two-dimensional flowfield resulting from the interaction of a moving planar shock wave with a compression corner is determined using a second-order, discontinuity-fitting, finite-difference approach. The time-dependent Euler equations are transformed to normalize the distance between the body and peripheral shock and to include the existing self-similar property of the flow. The resulting set of partial differential equations in conservation-law form is then solved in a time-dependent fashion using MacCormack's scheme. The vortical singularity, which lies on the body surface, and the single reflected shock are both treated as discontinuities in the numerical procedure. The results of the numerical simulation compare quite favorably with existing experimental interferograms and yield better flowfield resolution than previous first-order, shock-capturing, numerical solutions.

Kutler, P.↗

Diaplectic Glass Content in Experimentally Shock-loaded Quartz Determined by X-Ray Powder Diffraction

Quartz is the most common mineral of terrestrial crustal rocks and thus a widespread indicator for impact cratering and associated shock metamorphism. Planar deformation features (PDFs) are among the most prominent and diagnostic shock features in quartz and they represent thin lamellae of glass that formed via solid-state transformations. This socalled 'diaplectic' glass becomes pervasive at higher pressures and results in optically isotropic and X-ray-amorphous phases that resemble texturally the original quartz grains (without evidence of melt flow). In the past, it has been shown that the amount of this amorphous material in experimentally shock-loaded quartz correlates with peak shock pressure. Both reports derive the glass content from density measurements of individual crystals employing the equation X(%) = (rho(sub x) - rho(sub 0))/(rho(sub x) - rho(sub gl)), where x and 0 stands for X-ray and average (optical) density, respectively. The density of glass, rho(sub gl), was adopted as 2.2 g/cu cm. Though the same procedures had been applied, the resulting glass content differs significantly among the above studies. In the present study, we are using a new approach based solely on the integral intensity of a single, carefully selected reflection in the XRD pattern, and we will compare our data to those reported in the literature.

Skala, R.↗

Alpha-helical hydrophobic polypeptides form proton-selective channels in lipid bilayers

Proton translocation is important in membrane-mediated processes such as ATP-dependent proton pumps, ATP synthesis, bacteriorhodopsin, and cytochrome oxidase function. The fundamental mechanism, however, is poorly understood. To test the theoretical possibility that bundles of hydrophobic alpha-helices could provide a low energy pathway for ion translocation through the lipid bilayer, polyamino acids were incorporated into extruded liposomes and planar lipid membranes, and proton translocation was measured. Liposomes with incorporated long-chain poly-L-alanine or poly-L-leucine were found to have proton permeability coefficients 5 to 7 times greater than control liposomes, whereas short-chain polyamino acids had relatively little effect. Potassium permeability was not increased markedly by any of the polyamino acids tested. Analytical thin layer chromatography measurements of lipid content and a fluorescamine assay for amino acids showed that there were approximately 135 polyleucine or 65 polyalanine molecules associated with each liposome. Fourier transform infrared spectroscopy indicated that a major fraction of the long-chain hydrophobic peptides existed in an alpha-helical conformation. Single-channel recording in both 0.1 N HCl and 0.1 M KCl was also used to determine whether proton-conducting channels formed in planar lipid membranes (phosphatidylcholine/phosphatidylethanolamine, 1:1). Poly-L-leucine and poly-L-alanine in HCl caused a 10- to 30-fold increase in frequency of conductive events compared to that seen in KCl or by the other polyamino acids in either solution. This finding correlates well with the liposome observations in which these two polyamino acids caused the largest increase in membrane proton permeability but had little effect on potassium permeability. Poly-L-leucine was considerably more conductive than poly-L-alanine due primarily to larger event amplitudes and, to a lesser extent, a higher event frequency. Poly-L-leucine caused two populations of conductive events, one in the 0.1-0.5 pA range, and one in the 1.0-5.0 pA range, whereas nearly all events caused by poly-L-alanine were in the 0.1-0.5 pA range at an applied voltage of +60 mV. The channel-like activity appeared to switch between conductive and nonconductive states, with most open-times in the range of 50-200 ms. We conclude that hydrophobic polyamino acids produce proton-conducting defects in lipid bilayers that may be used to model functional proton channels in biological membranes.

NASA Discipline Exobiology↗

Effects of shock pressures on calcic plagioclase

Calcic plagioclase single crystals were subjected to shock loading up to a pressure of 496 kbar; optical and electron microscope studies were conducted to investigate the shock-induced effects on the mineral, which is found in terrestrial and lunar rocks and in meteorites. It was observed that up to 287 kbar pressure, the recovered samples are essentially crystalline, while samples subjected to pressures between 300 and 400 kbar are almost 100% diaplectic glasses, suggesting shock transformation in the solid state. Samples shock-loaded to pressures greater than 400 kbar yielded glasses with refractive indices similar to those of thermally fused glass. It is concluded that planar features, absent in all the specimens, may not be definitive shock indicators, but may be linked to local heterogeneous dynamic stresses experienced by plagioclase grains within shocked rocks.

Gibbons, R. V.↗

A shock-layer theory based on thirteen-moment equations and DSMC calculations of rarefied hypersonic flows

Grad's thirteen-moment equations are applied to the flow behind a bow shock under the formalism of a thin shock layer. Comparison of this version of the theory with Direct Simulation Monte Carlo calculations of flows about a flat plate at finite attack angle has lent support to the approach as a useful extension of the continuum model for studying translational nonequilibrium in the shock layer. This paper reassesses the physical basis and limitations of the development with additional calculations and comparisons. The streamline correlation principle, which allows transformation of the 13-moment based system to one based on the Navier-Stokes equations, is extended to a three-dimensional formulation. The development yields a strip theory for planar lifting surfaces at finite incidences. Examples reveal that the lift-to-drag ratio is little influenced by planform geometry and varies with altitudes according to a 'bridging function' determined by correlated two-dimensional calculations.

Cheng, H. K.↗

Collisional Histories of Comets and Trojan Asteroids: Diopside, Magnesite, and Fayalite Impact Studies

Comets and asteroids have weathered dynamic histories, as evidenced by their rough surfaces. The Nice model describes a violent reshuffling of small bodies during the Late Heavy Bombardment, with collisions acting to grind these planetesimals away. This creates an additional source of impact material that can re-work the surfaces of the larger bodies over the lifetime of the solar system. Here, we investigate the possibility that signatures due to impacts (e.g. from micrometeoroids or meteoroids) could be detected in their spectra, and how that can be explained by the physical manifestation of shock in the crystalline structure of minerals. All impact experiments were conducted in the Johnson Space Center Experimental Impact Laboratory using the vertical gun. Impact speeds ranged from approx.2.0 km/s to approx.2.8 km/s. All experiments were conducted at room temperature. Minerals found in comets and asteroids were chosen as targets, including diopside (MgCaSi2O6, monoclinic pyroxene), magnesite (MgCO3, carbonate), and fayalite (FeSiO4, olivine). Impacted samples were analyzed using a Fourier Transform Infrared Spectrometer (FTIR) and a Transmission Electron Microscope (TEM). Absorbance features in the 8-13 m spectral region demonstrate relative amplitude changes as well as wavelength shifts. Corresponding TEM images exhibit planar shock dislocations in the crystalline structure, attributed to deformation at high strain and low temperatures. Elongating or shortening the axes of the crystalline structure of forsterite (Mg2SiO4, olivine) using a discrete dipole approximation model (Lindsay et al., submitted) yields changes in spectral features similar to those observed in our impacted laboratory minerals.

Lederer, S. M.↗

Energy functions for regularization algorithms

Regularization techniques are widely used for inverse problem solving in computer vision such as surface reconstruction, edge detection, or optical flow estimation. Energy functions used for regularization algorithms measure how smooth a curve or surface is, and to render acceptable solutions these energies must verify certain properties such as invariance with Euclidean transformations or invariance with parameterization. The notion of smoothness energy is extended here to the notion of a differential stabilizer, and it is shown that to void the systematic underestimation of undercurvature for planar curve fitting, it is necessary that circles be the curves of maximum smoothness. A set of stabilizers is proposed that meet this condition as well as invariance with rotation and parameterization.

Delingette, H.↗

Electromagnetic characterization of conformal antennas

The ultimate objective of this project is to develop a new technique which permits an accurate simulation of microstrip patch antennas or arrays with various feed, superstrate and/or substrate configurations residing in a recessed cavity whose aperture is planar, cylindrical or otherwise conformed to the substructure. The technique combines the finite element and boundary integral methods to formulate a system suitable for solution via the conjugate gradient method in conjunction with the fast Fourier transform. The final code is intended to compute both scattering and radiation patterns of the structure with an affordable memory demand. With upgraded capabilities, the four included papers examined the radar cross section (RCS), input impedance, gain, and resonant frequency of several rectangular configurations using different loading and substrate/superstrate configurations.

Volakis, John L.↗

Modal analysis of turborotors using planar modes - Theory

The generalized dynamic equations of motion have been obtained by the direct stiffness method for multimass flexible rotor bearing systems including the effects of gyroscopic moments, disk skew, and rotor acceleration. A set of undamped critical speed mode shapes calculated from the average horizontal and vertical bearing stiffness is used to transform the equations of motion into a set of coupled modal equations of motion. The modal equations are coupled by the generalized bearing coefficients and the gyroscopic moments. An analysis using only undamped critical speeds or decoupled modal analysis assuming proportional damping may lead to erroneous results. This paper presents a rapid method of calculating rotor resonance speeds with their corresponding amplification factors, stability and unbalance response of turborotors. Examples of the application of this modal approach are presented and results are compared to those of other methods such as matrix transfer analysis.

Gunter, E. J.↗

Diffraction studies of the high pressure phases of GaAs and GaP

High pressure structural phase transitions of GaAs and GaP have been studied by energy dispersive X-ray diffraction with the radiation from the Cornell High Energy Synchrotron Source. GaAs began to transform at 172 + or - 7 kbar to an orthorhombic structure possibly belonging to space group Fmmm. GaP transformed to a tetragonal beta-Sn type phase at 215 + or - 8 kbar. Although pressure transmitting media were used to minimize shear stresses in the specimens, the high pressure diffraction results were interpreted as showing evidence for planar defects in the specimens.

Baublitz, M., Jr.↗

An Experimental Investigation of Incompressible Richtmyer-Meshkov Instability

Richtmyer-Meshkov (RM) instability occurs when two different density fluids are impulsively accelerated in the direction normal to their nearly planar interface. The instability causes small perturbations on the interface to grow and eventually become a turbulent flow. It is closely related to Rayleigh-Taylor instability, which is the instability of a planar interface undergoing constant acceleration, such as caused by the suspension of a heavy fluid over a lighter one in the earth's gravitational field. Like the well-known Kelvin-Helmholtz instability, RM instability is a fundamental hydrodynamic instability which exhibits many of the nonlinear complexities that transform simple initial conditions into a complex turbulent flow. Furthermore, the simplicity of RM instability (in that it requires very few defining parameters), and the fact that it can be generated in a closed container, makes it an excellent test bed to study nonlinear stability theory as well as turbulent transport in a heterogeneous system. However, the fact that RM instability involves fluids of unequal densities which experience negligible gravitational force, except during the impulsive acceleration, requires RM instability experiments to be carried out under conditions of microgravity. This experimental study investigates the instability of an interface between incompressible, miscible liquids with an initial sinusoidal perturbation. The impulsive acceleration is generated by bouncing a rectangular tank containing two different density liquids off a retractable vertical spring. The initial perturbation is produced prior to release by oscillating the tank in the horizontal direction to produce a standing wave. The instability evolves in microgravity as the tank travels up and then down the vertical rails of a drop tower until hitting a shock absorber at the bottom. Planar Laser Induced Fluorescence (PLIF) is employed to visualize the flow. PLIF images are captured by a video camera that travels with the tank. Figure 1 is as sequence of images showing the development of the instability from the initial sinusoidal disturbance far into the nonlinear regime which is characterized by the appearance of mushroom structures resulting from the coalescence of baroclinic vorticity produced by the impulsive acceleration. At later times in this sequence the vortex cores are observed to become unstable showing the beginnings of the transition to turbulence in this flow. The amplitude of the growing disturbance after the impulsive acceleration is measured and found to agree well with theoretical predictions. The effects of Reynolds number (based on circulation) on the development of the vortices and the transition to turbulence are also determined.

Jacobs, J. W.↗

A Cryogenic Waveguide Mount for Microstrip Circuit and Material Characterization

A waveguide split-block fixture used in the characterization of thin-film superconducting planar circuitry at millimeter wavelengths is described in detail. The test fixture is realized from a pair of mode converters, which transition from rectangular-waveguide to on-chip microstrip-line signal propagation via a stepped ridge-guide impedance transformer. The observed performance of the W-band package at 4.2K has a maximum in-band transmission ripple of 2dB between 1.53 and 1.89 times the waveguide cutoff frequency. This metrology approach enables the characterization of superconducting microstrip test structures as a function temperature and frequency. The limitations of the method are discussed and representative data for superconducting Nb and NbTiN thin film microstrip resonators on single-crystal Si dielectric substrates are presented.

U-yen, Kongpop↗

A Cryogenic Waveguide Mount for Microstrip Circuit and Material Characterization

A waveguide split-block fixture used in the characterization of thin-film superconducting planar circuitry at millimeter wavelengths is described in detail. The test fixture is realized from a pair of mode converters, which transition from rectangular-waveguide to on-chip microstrip-line signal propagation via a stepped ridge-guide impedance transformer. The observed performance of the W-band package at 4.2K has a maximum in-band transmission ripple of 2dB between 1.53 and 1.89 times the waveguide cutoff frequency. This metrology approach enables the characterization of superconducting microstrip test structures as a function temperature and frequency. The limitations of the method are discussed and representative data for superconducting Nb and NbTiN thin film microstrip resonators on single-crystal Si dielectric substrates are presented.

U-yen, Kongpop↗

On the electromagnetic scattering from infinite rectangular grids with finite conductivity

A variety of methods can be used in constructing solutions to the problem of mesh scattering. However, each of these methods has certain drawbacks. The present paper is concerned with a new technique which is valid for all spacings. The new method involved, called the fast Fourier transform-conjugate gradient method (FFT-CGM), represents an iterative technique which employs the conjugate gradient method to improve upon each iterate, utilizing the fast Fourier transform. The FFT-CGM method provides a new accurate model which can be extended and applied to the more difficult problems of woven mesh surfaces. The formulation of the FFT-conjugate gradient method for aperture fields and current densities for a planar periodic structure is considered along with singular operators, the formulation of the FFT-CG method for thin wires with finite conductivity, and reflection coefficients.

Christodoulou, C. G.↗

Modified Polar-Format Software for Processing SAR Data

HMPF is a computer program that implements a modified polar-format algorithm for processing data from spaceborne synthetic-aperture radar (SAR) systems. Unlike prior polar-format processing algorithms, this algorithm is based on the assumption that the radar signal wavefronts are spherical rather than planar. The algorithm provides for resampling of SAR pulse data from slant range to radial distance from the center of a reference sphere that is nominally the local Earth surface. Then, invoking the projection-slice theorem, the resampled pulse data are Fourier-transformed over radial distance, arranged in the wavenumber domain according to the acquisition geometry, resampled to a Cartesian grid, and inverse-Fourier-transformed. The result of this process is the focused SAR image. HMPF, and perhaps other programs that implement variants of the algorithm, may give better accuracy than do prior algorithms for processing strip-map SAR data from high altitudes and may give better phase preservation relative to prior polar-format algorithms for processing spotlight-mode SAR data.

Chen, Curtis↗

Improved sonic-box computer program for calculating transonic aerodynamic loads on oscillating wings with thickness

A computer program was developed to account approximately for the effects of finite wing thickness in transonic potential flow over an oscillation wing of finite span. The program is based on the original sonic box computer program for planar wing which was extended to account for the effect of wing thickness. Computational efficiency and accuracy were improved and swept trailing edges were accounted for. Account for the nonuniform flow caused by finite thickness was made by application of the local linearization concept with appropriate coordinate transformation. A brief description of each computer routine and the applications of cubic spline and spline surface data fitting techniques used in the program are given, and the method of input was shown in detail. Sample calculations as well as a complete listing of the computer program listing are presented.

Ruo, S. Y.↗

Acoustic loading in planar networks

The acoustic loading in a complex planar network of ducts is determined by a method in which Green function surface elements are used. The network consists of straight ducts, elbows and branched ducts. A transfer matrix technique is developed in which each duct is treated separately and the matrix of the influence coefficients is transformed to tri-diagonal form allowing efficient inversion.

El-Raheb, M.↗

Electron microscopy of some experimentally shocked counterparts of lunar minerals.

Particulate samples of experimentally shocked olivine, enstatite, and apatite and their unshocked equivalents were thinned by ion bombardment and examined by transmission methods in a conventional (100 kV) electron microscope. Enstatite shock-loaded at a peak pressure of 250 kb was partly transformed to relatively dense inverse defect spinel. Magnesian olivine shocked at a peak pressure of 200 kb shows intense lattice deformation. Magnesian olivine shock-loaded at a peak pressure of 400 kb was recrystallized to very fine polycrystalline aggregates. Apatite shock-loaded at a peak pressure of 250 kb shows planar deformation elements and shock-induced imperfections.

Sclar, C. B.↗