Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “permeation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1975

A generalized expression for lag-time in the gas-phase permeation of hollow tubes

A generalized expression for the nonsteady-state parameter, lag-time, has been obtained from Fick's second law for gas-phase transport through hollow, cylindrical membranes. This generalized expression is simplified for three limiting cases of practical interest: (1) diffusion controlled transport, (2) phase boundary reaction control at the inlet surface, and (3) phase boundary reaction control at the outlet surface. In all three cases the lag-time expressions were found to be inversely proportional only to the diffusion coefficient and functionally dependent on the membrane radii. Finally, the lag-time expressions were applied to experimentally obtained lag-time data for alpha-phase titanium and alpha-phase iron.

Shah, K. K.↗
NASA NTRS1975

Differential permeation of artemia cysts and cucumber seeds by alcohols

The rate of penetration of the simpler alcohols into brine shrimp cysts and cucumber seeds was studied. In solutions below 70% the rate of penetration is related to lipid solvent capacity of the alcohol. In concentrations above 70%, particularly in absolute alcohols, methanol penetrates brine shrimp rapidly and ethanol penetrates slowly. All the other alcohols tested did not penetrate the dormant structures. Ethionine and deuteroxy-methanol did not affect the rate of penetration of methanol. It is suggested that in dehydrated membranes the lipid moiety is protected by a continuous sheet of protein. Methanol, which is fairly similar to water, is probably able to penetrate the membrane by initiating a conformation change in the protein, exposing the lipid which subsequently dissolves in the methanol thus destroying the membrane.

Smith, C. W.↗
NASA NTRS1976

Gas-phase hydrogen permeation through alpha-titanium - Surface film and dimensional effects

The two techniques normally used to determine diffusivity and permeability in metals are considered and a description is presented of experiments which had been conducted to determine the direct effect of oxide and nitride films on the membrane surface as a function of location and thickness. The test specimens used in the experiments has been machined from commercially pure titanium rod. The results of the experiments show that hydrogen transport in alpha-titanium is partially or completely controlled by surface reactions depending upon membrane wall thickness and the composition and thickness of the surface film.

Shah, K. K.↗
NASA NTRS1985

Water permeation and dielectric breakdown. Water permeability in Pub Tedlar. Pub/Tedlar as a function of temperature and humidity

Moisture transport and dielectric breakdown of polyvinyl butyral (PVB), Tedlar, and PVB/Tedlar composites were addressed. Data for the temperature range between 20 and 80 C showed that the moisture flux through the composite is governed by the slower material; and that the composite permeability is intermediate to those of the component material, as predicted by theory. Data for Tedlar at 71 C, showing the dependence of moisture flux on relative humidity, was also presented. Dielectric breakdown data were less precise and less conclusive. The generally applied theoretical model does not match the experimental data. The PVB/Tedlar composite exhibited greater voltage breakdown resistance than either component. Testing of EVA and EVA/Tedlar composites is underway.

Orehotsky, J.↗
NASA NTRS1988

Gas permeation measurements on small polymer specimens

Mass spectrometry was used to measure oxygen and nitrogen permeabilities while polarography was used to measure oxygen permeabilities for several contact lens materials. Applicable sample holders were designed and fabricated to accommodate curved and flat specimens. A prepared standard was used to calibrate the mass spectrometric analyses. The oxygen permeability values determined by mass spectrometry were significantly greater than those determined by polarography. This was attributed to the phase boundary phenomena and the limiting oxygen permeance of water inherent in the polarographic technique. Polarographic values determined were in good agreement with proprietary values obtained by polarography, with the exception of one material.

Burns, Karen S.↗
NASA NTRS2010

Operational Considerations for Oxygen Flammability Risks: Concentrated Oxygen Diffusion and Permeation Behaviors

Increased human spaceflight operations utilize oxygen concentrations that are frequently varied with use of concentrations up to 100 percent oxygen. Even after exiting a higher percentage oxygen environment, high oxygen concentrations can still be maintained due to material saturation and oxygen entrapment between barrier materials. This paper examines the material flammability concerns that arise from changing oxygen environments during spaceflight operations. We examine the time required for common spacecraft and spacesuit materials exposed to oxygen to return to reduced ignitability and flammability once removed from the increased concentration. Various common spacecraft materials were considered: spacecraft cabin environment foams, Extra Vehicular Mobility Unit materials and foams, Advanced Crew Escape Suit materials, and other materials of interest such as Cotton, Nomex^ HT90-40, and Tiburon Surgical Drape. This paper presents calculated diffusion coefficients derived from experimentally obtained oxygen transmission rates for the tested materials and the analytically derived times necessary for reduced flammability to be achieved based on NASA flammability criteria. Oxygen material saturation and entrapment scenarios are examined. Experimental verification data on oxygen diffusion in saturation scenarios are also presented and discussed. We examine how to use obtained data to address flammability concerns during operational planning to reduce the likelihood of fires while improving efficiency for procedures.

Harper, Susana↗
NASA NTRS2024

Oxygen Saturated Materials Diffusion and Permeation Flammability Testing

Increased material flammability in high oxygen concentrations presents safety/operational concerns. When exiting a higher oxygen concentration environment and moving to a lower one, localized high oxygen concentrations can remain. Understanding time needed to dissipate oxygen and equilibrate with new environment can reduce the likelihood of fires or improve procedures/efficiency as NASA moves to longer missions with increased extravehicular activities in both spacecraft and off-Earth habitats. This paper examines the time required for common spacecraft materials exposed to 100% oxygen to return to reduced ambient flammability.

Susana Harper↗
NASA NTRS2006

Screening and Identification of Cryopreservative Agents for Human Cellular Biotechnology Experiments in Microgravity

Dimethyl sulfoxide (DMSO) has been used as a standard cryopreservative agent for mammalian cell culture; however, prolonged exposure of thawed cells to DMSO can alter cell growth. While DMSO is easily eliminated in ground-based experiments, removal of DMSO in flight-based experiments is more difficult due to various on-orbit constraints. Failure of cryopreservation is due to a number of factors, including intracellular ice formation, solute effect, and apoptotic cell death following thawing. One objective of this study is to identify and characterize an alternative cryopreservative that could be used on the International Space Station (ISS). We systematically screened for potential permeating and non-permeating agents using a human colorectal carcinoma cell line, MIP-101. Cells were suspended in cryopreservation solution and frozen either following a two-step procedure involving initial cooling at -1 C/min overnight followed by storage in liquid nitrogen (LN2) vapor, or by freezing cells directly in the LN2 vapor phase at -10 C/min. Ability to preserve cellular function after one cycle of freeze-thawing was assessed by the recovery of viable cells in short and long-term cell culture experiments. Results showed that permeating preservatives glycerol (G) and ethylene glycol (EG) had an efficacy (80-110%) comparable to, if not better than, 7.5% DMSO; but, propylene glycol (PG) had a somewhat lesser efficacy. Among the non-permeating preservatives, trehalose, raffinose, and dextran exhibited significant protective effect (50-80%) relative to that offered by 7.5% DMSO, but at -10 C and not at -1 C/min cooling rate. Preliminary data thus suggest that a combination of permeating and non-permeating agents may have improved efficacy as a cryoprotectant and serve as an alternate to DMSO for experimentation on ISS.

Love,J.↗
NASA NTRS1972

Physical electronics and surface physics

Current analytical and experimental investigations of the influence of surface processes on the rate of permeation of gases through solids are summarized. A brief description is presented of an analytical model that provides an approximate prediction of the dependence of the permeation rate on the rates of surface processes relative to the rate of the diffusion process. Results of experiments indicate that the desorption process of hydrogen from various materials is influenced by surface impurities to the degree that substantial changes in the spatial distribution of the desorbed molecules are observed when the impurities are varied. Except possibly for H-Nb, the permeation measurements indicate that the desorption process is not influenced to the degree that detectable changes in the permeation rates are observed when the impurities and temperatures are varied. On the basis of analysis, it is unlikely that the desorption process will be the rate-controlling step under the conditions of the present experiments.

Stickney, R. E.↗
NASA NTRS1995

On-line removal of volatile fatty acids from CELSS anaerobic bioreactor via nanofiltration

The CELSS (controlled ecological life support system) resource recovery system, which is a waste processing system, uses aerobic and anaerobic bioreactors to recover plants nutrients and secondary foods from the inedible biomass. The anaerobic degradation of the inedible biomass by means of culture of rumen bacteria,generates organic compounds such as volatile fatty acids (acetic, propionic, butyric, VFA) and ammonia. The presence of VFA in the bioreactor medium at fairly low concentrations decreases the microbial population's metabolic reactions due to end-product inhibition. Technologies to remove VFA continuously from the bioreactor are of high interest. Several candidate technologies were analyzed, such as organic solvent liquid-liquid extraction, adsorption and/or ion exchange, dialysis, electrodialysis, and pressure driven membrane separation processes. The proposed technique for the on-line removal of VFA from the anaerobic bioreactor was a nanofiltration membrane recycle bioreactor. In order to establish the nanofiltration process performance variables before coupling it to the bioreactor, a series of experiments were carried out using a 10,000 MWCO tubular ceramic membrane module. The variables studied were the bioreactor slurry permeation characteristics, such as, the permeate flux, VFA and the nutrient removal rates as a function of applied transmembrane pressure, fluid recirculation velocity, suspended matter concentration, and process operating time. Results indicate that the permeate flux, VFA and nutrients removal rates are directly proportional to the fluid recirculation velocity in the range between 0.6 to 1.0 m/s, applied pressure when these are low than 1.5 bar, and inversely proportional to the total suspended solids concentration in the range between 23,466 to 34,880. At applied pressure higher than 1.5 bar the flux is not more linearly dependent due to concentration polarization and fouling effects over the membrange surface. It was also found that the permeate flux declines rapidly during the first 5 to 8 hours, and then levels off with a diminishing rate of flux decay.

Colon, Guillermo↗
NASA NTRS1994

Permeability of membranes to amino acids and modified amino acids: mechanisms involved in translocation

The amino acid permeability of membranes is of interest because they are one of the key solutes involved in cell function. Membrane permeability coefficients (P) for amino acid classes, including neutral, polar, hydrophobic, and charged species, have been measured and compared using a variety of techniques. Decreasing lipid chain length increased permeability slightly (5-fold), while variations in pH had only minor effects on the permeability coefficients of the amino acids tested in liposomes. Increasing the membrane surface charge increased the permeability of amino acids of the opposite charge, while increasing the cholesterol content decreased membrane permeability. The permeability coefficients for most amino acids tested were surprisingly similar to those previously measured for monovalent cations such as sodium and potassium (approximately 10(-12)-10(-13) cm s-1). This observation suggests that the permeation rates for the neutral, polar and charged amino acids are controlled by bilayer fluctuations and transient defects, rather than partition coefficients and Born energy barriers. Hydrophobic amino acids were 10(2) more permeable than the hydrophilic forms, reflecting their increased partition coefficient values. External pH had dramatic effects on the permeation rates for the modified amino acid lysine methyl ester in response to transmembrane pH gradients. It was established that lysine methyl ester and other modified short peptides permeate rapidly (P = 10(-2) cm s-1) as neutral (deprotonated) molecules. It was also shown that charge distributions dramatically alter permeation rates for modified di-peptides. These results may relate to the movement of peptides through membranes during protein translocation and to the origin of cellular membrane transport on the early Earth.

Review↗
NASA NTRS2009

Nano-Pervaporation Membrane with Heat Exchanger Generates Medical-Grade Water

A nanoporous membrane is used for the pervaporation process in which potable water is maintained, at atmospheric pressure, on the feed side of the membrane. The water enters the non-pervaporation (NPV) membrane device where it is separated into two streams -- retentate water and permeated water. The permeated pure water is removed by applying low vapor pressure on the permeate side to create water vapor before condensation. This permeated water vapor is subsequently condensed by coming in contact with the cool surface of a heat exchanger with heat being recovered through transfer to the feed water stream.

Tsai, Chung-Yi↗
NASA NTRS2014

Towards Co-evolution of Membrane Transport and Metabolism

Protocellular boundaries were inextricably connected to the metabolism they encapsulated: to be inheritable, early metabolism must have led to an increased rate of growth and division of vesicles and, similarly, transport through vesicle boundaries must have supported the evolution of metabolism. Even though explaining how this coupling emerged and evolved in the absence of the complex machinery of modern cells is one of the key issues in studies on the origin of life, little is known about the biochemical and biophysical processes that might have been involved. This gap in our knowledge is a major impediment in efforts to construct scenarios for the origin of life and laboratory models of protocells. A combination of experimental and computational studies carried out by us and our collaborators is aimed at helping to close this gap. Properties of membranes might have contributed to the selection of RNA as an early biopolymer. A kinetic mechanism was proposed (Sacerdote & Szostak, 2005) in which ribose was supplied more quickly than other aldopentoses to primordial cells for preferential incorporation of ribonucleotides into nucleic acids. This proposal is based on a finding that ribose permeates membranes an order of magnitude faster than its diastereomers, arabinose and xylose. Our computer simulations, which yield permeation rates in excellent agreement with experiment, and kinetic modeling explain this phenomenon in terms of inter- and intramolecular interactions involving exocyclic hydroxyl groups attached to carbon atoms of the pyranose ring (Wei and Pohorille, 2009). They also constrain scenarios for the formation of the earliest nucleic acids (Wei and Pohorille, 2013). In one scenario, sugars permeate protocellular walls and subsequently are used to synthesize nucleic acids inside protocells. As long as this process proceeds at the rate faster than 6x10(exp -3)/s, ribose derivatives will be available for synthesis easier than their diastereomers. If nucleosides or their activated derivatives are synthesized outside protocells and subsequently transported across protocellular membranes the kinetic mechanism does not apply because all diastereomers, which have their sugars in the furanose rather than pyranose form, permeate the membrane at approximately the same rate. Properties of membranes might have been also coupled to metabolism involving peptides. Recently, Adamala and Szostak (2013) have shown that a dipeptide inside fatty-acid vesicles catalyzes the formation of another dipeptide that binds to vesicle walls and, by doing so, promotes their growth at the expense of other vesicles. This coupling of metabolism, permeability of vesicles and their growth is the first demonstration of evolutionary advantage imparted by small, membrane-bound peptides. Building on this work we have calculated the rate at which different blocked amino acids are delivered to a protocell for synthesis of dipeptides. We have further shown that the dipeptides are located at the water-membrane interface rather than in the center of the bilayer. On these basis it is anticipated that other dipeptides containing aromatic, but not necessarily hydrophobic amino acids (e.g. tyrosine) could have the same catalytic effects. Insight from these studies allows for estimating the rate of vesicle growth and the rates of dipeptide synthesis required to keep the system in balance. These results, in combination with our earlier studies, lead to a general scenario for evolution from membrane-bound dipeptides to ion channels in the origin of life.

Metabolism↗
NASA NTRS1969

Device for obtaining separation of oxygen

Permeation membrane of a magnesium-nickel alloy of silver has the ability to permeate oxygen at high temperatures for an extended period of operation without failure. The measured rates of oxygen permeation in a tubular configuration of this alloy are higher than any previous rates published.

Glueckert, A. J.↗
NASA NTRS1972

Evaluation of advanced bladder technology

Research conducted during this period is reported. Studies presented include: (1) diffusion and permeation of CO2, O2, N2, and NO2 through polytetra fluoroethylene; (2) diffusion, permeation and solubility of simple gases (CO2, O2, N2, CH4, C2H6, C3H8, and C2H4) through a copolymer of hexafluoro propylene and tetrafluoro ethylene (FEP); (3) viscous flow and diffusion of gases throug small apertures; (4) diffusion and permeation of O2, N2, CO2, CH4, C2H6, and C3H8 through nitroso rubber; and (5) results of gas transport studies with carborane siloxane, nitroso rubber, silicone membrane, krytox coating on teflon, and FEP coated glass cloth. Publications generated under this program are listed.

Christensen, M. V.↗
NASA NTRS1974

Hydrogen transport in alpha titanium

Permeation experiments after nitriding the inlet surface of a hollow cylindrical membrane were conducted. Permeation data on two additional specimens given pre-oxidation or pre-nitriding treatments at both inlet and outlet surfaces are presented in terms of Arrhenius plots. Additionally, an analysis of geometry dependence on permeation rate was made for several specimens including the ones mentioned above. For simplicity in this report, the term as-polished is used to refer to a specimen which is either as-polished or is as-polished, pre-oxidized and annealed.

Johnson, D. L.↗
NASA NTRS1990

Reference NO2 calibration system for ground-based intercomparisons during NASA's GTE/CITE 2 mission

An NO2 calibration system, based on a permeation device and a two-stage dynamic dilution system, was designed, constructed, and characterized at the National Bureau of Standards. In this system, calibrant flow entering the second stage was controlled without contacting a metal flow controller, and permeation oven temperature and flow were continuously maintained, even during transport. The system performance and the permeation emission rate were characterized by extensive laboratory tests. This system was capable of accurately delivering known NO2 concentrations in the ppbv and sub-ppbv concentration range with a total uncertainty of approximately 10 percent. The calibration system was placed on board NASA research aircraft at both the Wallops Island and Ames research facilities. There it was employed as the reference standard in NASA's Global Tropospheric Experiment/Chemical Instrumental Test and Evaluation 2 mission in August 1986.

Fried, Alan↗
NASA NTRS1998

Enhanced Glow Discharge Production of Oxygen

Studies starting in late seventies have shown Mars atmosphere can be used as a feedstock for oxygen production using simple chemical processing systems during early phases of the Mars exploration program. This approach has been recognized as one of the most important in-situ resource utilization (ISRU) concepts for enabling future round trip Mars missions. It was determined a decade ago that separation of oxygen can be accomplished efficiently by permeation through a silver membrane at temperatures well below 1000 K. This process involves adsorption of atomic oxygen on the surface and its subsequent diffusion through a silver lattice via an oxygen concentration gradient. We have determined recently that glow discharge can be used to liberate atomic oxygen from Mars atmosphere and that the oxygen can be collected through a silver permeation membrane. Recently, we demonstrated a substantial increase in energy efficiency of the process by applying a radio frequency discharge in combination with a silver permeation membrane. The experiments were performed using pure carbon dioxide in the pressure range equal to Mars surface conditions. Energy efficiency was defined as the ratio of the energy required to dissociate a unit mass of oxygen from carbon dioxide to the (electrical) energy consumed by the overall system during the dissociation and collection process. The research effort, started at NASA Langley Research Center, continued with this project. Oxygen production apparatus, built and operated under the research grant NAG1-1140 was relocated to the Atomic Beams Laboratory at ODU in July 1996, being since then in fall operation.

Ash, Robert↗