SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
None given.(from task description): Objectives: test the communication network, determine how communication rates scale with message size, test the effect of contention, show the effect of contention.
This paper studies the ionospheric response to major geomagnetic storm of October 18-19, 1995, using the thermosphere-ionosphere electrodynamic general circulation model (TIE-GCM) simulations and the global ionospheric maps (GIM) of total electron content (TEC) observations from the Global Positioning System (GPS) worldwide network.
Alternatives for realizing a packet-based network switch for use on a frequency division multiple access/time division multiplexed (FDMA/TDM) geostationary communication satellite were investigated. Each of the eight downlink beams supports eight directed dwells. The design needed to accommodate multicast packets with very low probability of loss due to contention. Three switch architectures were designed and analyzed. An output-queued, shared bus system yielded a functionally simple system, utilizing a first-in, first-out (FIFO) memory per downlink dwell, but at the expense of a large total memory requirement. A shared memory architecture offered the most efficiency in memory requirements, requiring about half the memory of the shared bus design. The processing requirement for the shared-memory system adds system complexity that may offset the benefits of the smaller memory. An alternative design using a shared memory buffer per downlink beam decreases circuit complexity through a distributed design, and requires at most 1000 packets of memory more than the completely shared memory design. Modifications to the basic packet switch designs were proposed to accommodate circuit-switched traffic, which must be served on a periodic basis with minimal delay. Methods for dynamically controlling the downlink dwell lengths were developed and analyzed. These methods adapt quickly to changing traffic demands, and do not add significant complexity or cost to the satellite and ground station designs. Methods for reducing the memory requirement by not requiring the satellite to store full packets were also proposed and analyzed. In addition, optimal packet and dwell lengths were computed as functions of memory size for the three switch architectures.
Five ground-based total ozone spectrophotometers were intercompared at Wallops Island, VA between October 1979 and January 1981. The tests were conducted to evaluate the stability and accuracy of each instrument over an extended time period. Acceptable performance regarding these two characteristics is essential if an instrument is to be useful in field measurements and network monitoring of the atmospheric total ozone content. The Dobson spectrophotometer was used as the standard of comparison for the Brewer grating spectrophotometer, the USSR M-83 ozonometer, the Canterbury filter photometer, and the SenTran filter photometer. The grating instrument was found to be potentially the equal of the Dobson but was subject to unreliable performance by its rather sophisticated electronic components. The filter photometers performed acceptably for short periods but filter aging and eventual degradation rendered both units unusable before the end of the intercomparison. Finally, the M-83 results were found to be in acceptable agreement with the Dobson throughout the period when certain qualifications are invoked. The accuracy of a single M-83 ozone measurement may be low. Averages tend to improve its agreement with the Dobson.
Global ionospheric mapping (GIM) is a new, emerging technique for determining global ionospheric TEC (total electron content) based on measurements from a worldwide network of Global Positioning System (GPS) receivers.
Future space crews will face several challenges such as living and working in a confined environment, isolated from others. These circumstances increase the importance of interpersonal compatibility, teamwork, and team performance. The interpersonal compatibility of space crews has been and continues to be of interest to both NASA and the Institute of Biomedical Problems (IBMP), whose research informs operations for Roscosmos. In NASA-sponsored research, interpersonal compatibility has been examined in terms of how the combination of team members’ personality traits, values, and demographics shape team member relationships and team performance overtime. IBMP-sponsored research mostly has moved away from trait-based approaches toward an idiographic (in-depth, heavily descriptive) approach to researching crew interpersonal relations. This research uses software such as Personal Self-Perception and Attitudes (PSPA), network approaches to team member relations, and content analysis of interactions to assess interpersonal compatibility, and infer states and team dynamics. Our research program integrated these ideas. Our primary research aim was to develop and empirically test a process model of interpersonal relationship formation in isolated and confinement environments. We created a model, collected data from teams in an isolated and confined environment, and applied a novel analytical strategy that combines trait, state, and interaction data (i.e., relational events). We focused specifically on the formation of strained relationships in isolation and confinement—or with whom fellow crewmembers find it difficult to work.
The accuracy of satellite-based single-frequency radar ocean altimeters benefits from calibration of the total electron content (TEC) of the ionosphere below the satellite. Data from the global network of Global Positioning System (GPS) receivers provides timely, continuous, and globally well-distributed measurements of ionospheric electron content. We have created a daily automated process called Daily Global Ionospheric Map (Daily-GIM) whose primary purpose is to use global GPS data to provide ionospheric calibration data for the Geosat Follow-On (GFO) ocean altimeter. This process also produces an hourly time-series of global maps of the electron content of the ionosphere. This system is designed to deliver "quick-look" ionospheric calibrations within 24 hours with 90+% reliability and with a root-mean-square accuracy of 2 cm at 13.6 GHz. In addition we produce a second product within 72 hours which takes advantage of additional GPS data which were not available in time for the first process. The diagram shows an example of a comparison between TEC data from the Topographic Experiment (TOPEX) ocean altimeter and Daily-GIM. TEC are displayed in TEC units, TECU, where 5 TECU is 1 cm at 13.6 GHz. Data from a single TOPEX track is shown. Also shown is the Bent climatological model TEC for the track. Although the GFO satellite is not yet in its operational mode, we have been running Daily-GIM reliably (much better than 90%) with better than 2-cm accuracy (based on comparisons against TOPEX) for several months. When timely ephemeris files for the European Remote Sensing Satellite 2 (ERS-2) are available, daily ERS-2 altimeter ionospheric calibration files are produced. When GFO ephemeris files are made available to us, we produce GFO ionosphere calibration files. Users of these GFO ionosphere calibration files find they are a great improvement over the alternative International Reference Ionosphere 1995 (IRI-95) climatological model. In addition, the TOPEX orbit determination team at JPL has been using the global ionospheric maps to calibrate the single frequency GPS data from the TOPEX receiver, and report highly significant improvements in the ephemeris. The global ionospheric maps are delivered daily to the International GPS Service (IGS), making them available to the scientific community. Additional information is contained in the original.
Measurement and feedback control of nutrient solutions in plant root zones is critical to the development of healthy plants in both terrestrial and reduced-gravity environments. In addition to the water content, the amount of fertilizer in the nutrient solution is important to plant health. This typically requires a separate set of sensors to accomplish. A combination bulk moisture and salinity sensor has been designed, built, and tested with different nutrient solutions in several substrates. The substrates include glass beads, a clay-like substrate, and a nutrient-enriched substrate with the presence of plant roots. By measuring two key parameters, the sensor is able to monitor both the volumetric water content and salinity of the nutrient solution in bulk media. Many commercially available moisture sensors are point sensors, making localized measurements over a small volume at the point of insertion. Consequently, they are more prone to suffer from interferences with air bubbles, contact area of media, and root growth. This makes it difficult to get an accurate representation of true moisture content and distribution in the bulk media. Additionally, a network of point sensors is required, increasing the cabling, data acquisition, and calibration requirements. measure the dielectric properties of a material in the annular space of the vessel. Because the pore water in the media often has high salinity, a method to measure the media moisture content and salinity simultaneously was devised. Characterization of the frequency response for capacitance and conductance across the electrodes was completed for 2-mm glass bead media, 1- to 2-mm Turface (a clay like media), and 1- to 2-mm fertilized Turface with the presence of root mass. These measurements were then used to find empirical relationships among capacitance (C), the dissipation factor (D), the volumetric water content, and the pore water salinity.
The geomagnetic storms of April 17-21,2002 and May 29-30,2003 caused large decreases in the O/N2 column density ratio in the thermosphere. For these storms, O/N2 column density decreases of greater than 50% were observed to extend to mid-to-low latitudes with the FUV sensitive Earth Camera of the Visible Imaging System (VIS) on the Polar spacecraft. Simultaneously in these same regions, the ground-based GPS network observed approximately 80% reductions in the Total Electron Content (TEC) of the ionosphere. The reduction in the O/N2 column density ratio is due mainly to increases in the molecular species that have welled-up into the thermosphere from the lower levels of the atmosphere due to auroral heating. The geomagnetic-storm driven increase in molecular densities at typical ionospheric heights rapidly charge exchange with the ambient ionized atoms and subsequently dissociatively recombine with the ionospheric electrons leading to a reduction in the total charge density. The transition boundaries between high and low regions of O/N2 as well as TEC can be tracked in the images and the thermospheric winds may be inferred from the motion of the boundaries. The motion of these boundaries during the development of the geomagnetic storm will be discussed.
NASA's Deep Space Network (DSN) is an international network of antennas that support interplanetary spacecraft missions and radio and radar astronomy observations for the exploration of the solar system and the universe. The network also supports selected Earth-orbiting missions and collaborates with international partners such as European Space Agency (ESA), NASDA, CNES, etc.
A computer program uses data from more than 1,000 Global Positioning System (GPS) receivers in an Internet-accessible global network to generate daily estimates of the global distribution of vertical total electron content (VTEC) of the ionosphere. This program supersedes an older program capable of processing readings from only about 200 GPS receivers. This program downloads the data via the Internet, then processes the data in three stages. In the first stage, raw data from a global subnetwork of about 200 receivers are preprocessed, station by station, in a Kalman-filter-based least-squares estimation scheme that estimates satellite and receiver differential biases for these receivers and for satellites. In the second stage, an observation equation that incorporates the results from the first stage and the raw data from the remaining 800 receivers is solved to obtain the differential biases for these receivers. The only remaining error sources for which an account cannot be given are multipath and receiver noise contributions. The third stage is a postprocessing stage in which all the processed data are combined and used to generate new data products, including receiver differential biases and global and regional VTEC maps and animations.
The geomagnetic storms of April 17-21,2002 and May 29-30,2003 caused large decreases in the O/N2 column density ratio in the thermosphere. For these storms, ON2 column density decreases of greater than 50% were observed to extend to mid-to-low latitudes with the FUV sensitive Earth Camera of the Visible Imaging System (VIS) on the Polar spacecraft. Simultaneously in these same regions, the ground-based GPS network observed approximately 80% reductions in the Total Electron Content (TEC) of the ionosphere. The reduction in the Om2 column density ratio is due mainly to increases in the molecular species that have welled-up into the thermosphere from the lower levels of the atmosphere due to auroral heating. The geomagnetic-storm driven increase in molecular densities at typical ionospheric heights rapidly charge exchange with the ambient ionized atoms and subsequently dissociatively recombine with the ionospheric electrons leading to a reduction in the total charge density. The transition boundaries between high and low regions of O/N2 as well as TEC can be tracked in the images and the thermospheric winds can be determined from the motion of the boundaries. The motion of these boundaries during the development of the geomagnetic storm will be discussed.
In this study, we apply the electromagnetic (EM) melt processing of thermoplastics on an innovative EM field-driven powder bed fusion additive manufacturing (AM) concept for high-performance functional parts: Selective Microwave Melting/Sintering (SMM/SMS). This technique leverages the EM susceptibility of carbon nanotube-coated polymer micro-pellets to achieve rapid, localized heating and powder fusion. Thus, selective microwave melting (SMM) was used to fabricate multilayer specimens made of recycled polyphenylene sulfide (rPPS) and carbon nanotubes (CNTs). The resulting SMM specimens exhibited very good interlayer integrity, localized fusion at pellet boundaries, and tolerable residual porosity, indicating effective fusion and acceptable consolidation. CNT-rich interphases were retained after irradiation, generating anisotropic electrically active network pathways and enabling conductivity enhancement at low filler content. At only 1.0 wt% CNT, the specimens exhibited electrical conductivity approximately three orders of magnitude higher than neat rPPS. Dynamic mechanical analysis showed improved viscoelastic response relative to neat rPPS, while tensile testing confirmed that the SMM-processed specimens retained practical mechanical integrity despite localized voids. These results demonstrate that SMM can effectively consolidate EM susceptible thermoplastic powder beds while preserving their segregated conductive networks. This may become a scalable route for producing multifunctional thermoplastic parts with low filler loadings, tunable anisotropy, and structured materials and parts. Overall, the findings suggest that EM field-based AM can help overcome key limitations of conventional thermoplastic processing by enabling scalable, energy-efficient fabrication of nanostructured composites and expanding AM to a broader range of resins, including high-performance thermoplastics with customized functional properties.
The goal of the Spring 1990 EGM 4001 Design class was to design, fabricate, and test sensors and control systems for a closed loop life support system (CLLSS). The designs investigated were to contribute to the development of NASA's Controlled Ecological Life Support System (CELSS) at Kennedy Space Center (KSC). Designs included a seed moisture content sensor, a porous medium wetness sensor, a plant health sensor, and a neural network control system. The seed group focused on the design and implementation of a sensor that could detect the moisture content of a seed batch. The porous medium wetness group concentrated on the development of a sensor to monitor the amount of nutrient solution within a porous plate incorporating either infrared reflectance or thermal conductance properties. The plant health group examined the possibility of remotely monitoring the health of the plants within the Biomass Production Chamber (BPC) using infrared reflectance properties. Finally, the neural network group concentrated on the ability to use parallel processing in order to control a robot arm and analyze the data from the health sensor to detect regions of a plant.
A potential application is outlined for high-speed and high-performance networks of the future. A discussion is presented of possible contents of the NSE (National Software Exchange) services to be offered by the NSE, mechanisms for controlling software quality, and types of collaboration that might involve the NSE. Services that must be provided by the NREN (National Research and Education Network) to provide adequate support for the NSE are identified.
As human space exploration pursues journeying to the Moon and Mars, international and intercultural collaboration is key for the success of such ambitious goals. Since 2014, NASA's Johnson Space Center (JSC) Hispanic Employee Resource Group (HERG) has established relationships and participated in outreach events with emerging space organizations in Latin America with educational and public outreach as a common goal. Such efforts align with strategic goals to empower the next generation of innovators and explorers and to champion the development of space exploration capabilities. This paper discusses the partnerships developed to introduce Spanish speaking populations to science, space technology, aeronautics, research and development through television, webcasts and social media. The authors share accomplishments, challenges, and lessons learned to build foundations for international collaboration to ignite research and innovation and propel human space exploration. The methodology makes use of Space Act Agreements to leverage existing outreach materials and programs and translate the content into Spanish for the benefit of students, educational organizations and the public in general. The plan is to apply the same model in other regions and countries to create a Latin American network of language translation and diffusion of science and space technology content targeting emerging space sectors. This model could be used to reach out to other international communities to provide cultural and educational outreach for space exploration and research.
In multicomputers that utilize circuit switching or wormhole routing, communication overhead depends largely on link contention - the variation due to distance between nodes is negligible. This has a major impact on the load balancing problem. In this case, there are some nodes with excess load (sources) and others with deficit load (sinks) and it is required to find a matching of sources to sinks that avoids contention. The problem is made complex by the hardwired routing on currently available machines: the user can control only which nodes communicate but not how the messages are routed. Network flow models of message flow in the mesh and the hypercube were developed to solve this problem. The crucial property of these models is the correspondence between minimum cost flows and correctly routed messages. To solve a given load balancing problem, a minimum cost flow algorithm is applied to the network. This permits one to determine efficiently a maximum contention free matching of sources to sinks which, in turn, tells one how much of the given imbalance can be eliminated without contention.