Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “net present value”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Focusing of nonducted whistlers by the equatorial anomaly

Impulsive ELF/VLF electric field bursts observed by the vector electric field instrument (VEFI) on the Dynamics Explorer 2 (DE 2) satellite on almost every crossing of the geomagnetic equator in the evening hours are interpreted as originating in lightning discharges. These signals that peak in intensity near the magnetic equator are observed within 5-20 deg latitude of the geomagnetic equator at altitudes of 300-500 km with amplitudes of the order of approximately mV/m in the 512- or 1024-Hz frequency band of the VEFI instrument. Whistler-mode ELF/VLF wave propagation through a horizontally stratified ionosphere predicts strong attenuation of subionospheric signals reaching the equator at low altitudes. However, ray tracing analysis shows that the presence of the equatorial density anomaly, commonly observed in the upper ionosphere during evening hours, leads to the focusing of the wave energy from lightning near the geomagnetic equator at low altitudes, thus accounting for all observed aspects of the phenomenon. The observations presented here indicate that during certain hours in the evening, almost all the energy input from lightning discharges entering the ionosphere at less than 30 deg latitude remains confined to a small region (in altitude and latitude) near the geomagnetic equator. The net wideband electric field, extrapolated from the observed electric field values in the 512- to 1024-Hz band, can be approximately 10 mV/m or higher. These strong electric fields generated in the ionosphere by lightning at local evening times may be important for the equatorial electrodynamics of the ionosphere.

Sonwalkar, Vikas S.↗
NASA NTRS1987

Skin friction measurements following manipulation of a turbulent boundary layer

Results are presented from three experiments in which direct, local measurements of the skin friction reduction due to flat-plate turbulence manipulators for overall viscous drag reduction were obtained. The results suggest that only a very small overall net drag reduction will be possible for such devices at moderate momentum thickness-derived Reynolds number values, since maximum skin friction drag is neither large nor sustained.

Nguyen, V. D.↗
NASA NTRS1994

Airborne boundary layer flux measurements of trace species over Canadian boreal forest and northern wetland regions

Airborne heat, moisture, O3, CO, and CH4 flux measurements were obtained over the Hudson Bay lowlands (HBL) and northern boreal forest regions of Canada during July - August 1990. The airborne flux measurements were an integral part of the NASA/Arctic Boundary Layer Expedition (ABLE) 3B field experiment executed in collaboration with the Canadian Northern Wetlands Study (NOWES). Airborne CH4 flux measurements were taken over a large portion of the HBL. The surface level flux of CH4 was obtained from downward extrapolations of multiple-level CH4 flux measurements. Methane source strengths ranged from -1 to 31 mg m(exp -2)/d, with the higher values occurring in relatively small, isolated areas. Similar measurements of the CH4 source strength in the boreal forest region of Schefferville, Quebec, ranged from 6 to 27 mg m(exp -2)/d and exhibited a diurnal dependence. The CH4 source strengths found during the ABLE 3B expedition were much lower than the seasonally averaged source strength of 51 mg m(exp -2)/d found for the Yukon-Kuskokwim delta region of Alaska during the previous ABLE 3A study. Large positive CO fluxes (0.31 to 0.53 parts per billion by volume (ppbv) m/s) were observed over the inland, forested regions of the HBL study area, although the mechanism for the generation of these fluxes was not identified. Repetitive measurements along the same ground track at various times of day near the Schefferville site also suggested a diurnal dependence for CO emissions. Measurements of surface resistance to the uptake of O3 (1.91 to 0.80 s/cm) for the HBL areas investigated were comparable to those observed near the Schefferville site (3.40 to 1.10 s/cm). Surface resistance values for the ABLE 3B study area were somewhat less than those observed over the Yukon-Kuskokwim delta during the previous ABLE 3A study. The budgets for heat, moisture, O3, CO, and CH4 were evaluated. The residuals from these budget studies indicated, for the cases selected, a moderate net photochemical production of O3 present in the boundary layer over the HBL that coincided with an in situ destruction of CO, although the mechanism responsible for the destruction of CO was not identified. Results from the O3 budget analysis indicate the importance of in situ photochemical production and its possible dominance over surface deposition to the local O3 budget at the Schefferville site. Measurements of the in situ production of O3 indicated a direct relationship between the presence of biomass burning or large-scale pollution effects. Residuals from budget calculations for conserved quantities (heat, moisture, and CH4) were compared with their respective surface fluxes to provide a measure of the internal self-consistency of the flux measurements.

Ritter, John A.↗
NASA NTRS1990

Neuromorphic learning of continuous-valued mappings from noise-corrupted data. Application to real-time adaptive control

The ability of feed-forward neural network architectures to learn continuous valued mappings in the presence of noise was demonstrated in relation to parameter identification and real-time adaptive control applications. An error function was introduced to help optimize parameter values such as number of training iterations, observation time, sampling rate, and scaling of the control signal. The learning performance depended essentially on the degree of embodiment of the control law in the training data set and on the degree of uniformity of the probability distribution function of the data that are presented to the net during sequence. When a control law was corrupted by noise, the fluctuations of the training data biased the probability distribution function of the training data sequence. Only if the noise contamination is minimized and the degree of embodiment of the control law is maximized, can a neural net develop a good representation of the mapping and be used as a neurocontroller. A multilayer net was trained with back-error-propagation to control a cart-pole system for linear and nonlinear control laws in the presence of data processing noise and measurement noise. The neurocontroller exhibited noise-filtering properties and was found to operate more smoothly than the teacher in the presence of measurement noise.

Troudet, Terry↗
NASA NTRS2004

Optics-Only Calibration of a Neural-Net Based Optical NDE Method for Structural Health Monitoring

A calibration process is presented that uses optical measurements alone to calibrate a neural-net based NDE method. The method itself detects small changes in the vibration mode shapes of structures. The optics-only calibration process confirms previous work that the sensitivity to vibration-amplitude changes can be as small as 10 nanometers. A more practical value in an NDE service laboratory is shown to be 50 nanometers. Both model-generated and experimental calibrations are demonstrated using two implementations of the calibration technique. The implementations are based on previously published demonstrations of the NDE method and an alternative calibration procedure that depends on comparing neural-net and point sensor measurements. The optics-only calibration method, unlike the alternative method, does not require modifications of the structure being tested or the creation of calibration objects. The calibration process can be used to test improvements in the NDE process and to develop a vibration-mode-independence of damagedetection sensitivity. The calibration effort was intended to support NASA s objective to promote safety in the operations of ground test facilities or aviation safety, in general, by allowing the detection of the gradual onset of structural changes and damage.

Decker, Arthur J.↗
NASA NTRS1994

Low Ozone in the Marine Boundary Layer of the Tropical Pacific Ocean

Aircraft measurements of ozone, its key precursors, and a variety of chemical tracers were made in the troposphere of the western and central Pacific in October 1991. These data are presented and analyzed to examine the occurrence of low ozone concentrations in the remote marine boundary layer of the tropical and equatorial Pacific Ocean. The data from these flights out of Guam, covering an area extending from the equator to 20 N and from south of the Philippines to Hawaii, show average O3 concentrations as low as 8-9 ppb (ppb=10(exp-9)v/v) at altitudes of 0.3-0.5 km in the boundary layer. Individual measurements as low as 2-5 ppb were recorded. Low O3 concentrations do not always persist in space and time. High O3, generally associated with the transport of upper tropospheric air, was also encountered in the boundary layer. In practically all cases, O3 increased to values as large as 25-30 ppb within 2 km above the boundary layer top. Steady state model computations are used to suggest that these low O3 concentrations are a result of net photochemical O3 destruction in a low NO environment, sea-surface deposition, and extremely low net entrainment rates (1-2 mm per second) from the free troposphere. Day/night measurements of ethane, propane, gaseous and aerosol Cl suggest that daytime (morning) Cl atom concentrations in the vicinity of 10(exp 5) molecules per cubic centimeter may be present in the marine boundary layer. This Cl atom abundance can be rationalized only if sea salt aerosols can release free chlorine (Cl2) to the gas phase in the presence of sun light (and possibly O3). These Cl atom concentrations, however, are still insufficient and Cl (or Br) chemistry is not likely to be an important cause of the observed low O3.

Singh, Hanwant B.↗
NASA NTRS1984

Structure-activity correlations for organophosphorus ester anticholinesterases. Part 2: CNDO/2 calculations applied to ester hydrolysis rates

Quantitative structure-activity relationships are presented for the hydrolysis of organophosphorus esters, RR'P(O)X, where R and R' are alkyl and/or alkoxy groups and X is fluorine, chlorine or a phenoxy group. CNDO/2 calculations provide values for molecular parameters that correlate with alkaline hydrolysis rates. For each subset of esters with the same leaving group, X, the CNDO-derived net atomic charge at the central phosphorus atom correlates well with the alkaline hydrolysis rate constants. For the whole set of esters with different leaving groups, equations are derived that relate charge, orbital energy and bond order to the hydrolysis rate constants.

Johnson, H.↗
NASA NTRS1991

Multispectral satellite data in the context of land surface heat balance

Multispectral satellite data are demonstrated to be an important potential contributor to the understanding and completeness of heat balance analysis. Satellite observations are presented, including visible, near-IR, IR, and microwave bands, which estimate surface characteristics and surface fluctuations. The relationship of the interannual variations of the satellite data and the land surface changes is discussed. It is shown that spatially representative values of global fluxes and parameters from multispectral data can consistently enhance the results of heat balance analysis. Daily net radiation can be estimated with a 10 percent error, while the error for albedo would be higher. Computations for all heat fluxes except the latent heat flux are shown. Soil moisture and surface temperature estimates can be derived from microwave and IR observations, respectively. Spectral reflectances in the visible and near-IR bands are suggested as important heat-balance indices for future consideration.

Choudhury, Bhaskar J.↗
NASA NTRS2010

Modeling the Information Age Combat Model: An Agent-Based Simulation of Network Centric Operations

The Information Age Combat Model (IACM) was introduced by Cares in 2005 to contribute to the development of an understanding of the influence of connectivity on force effectiveness that can eventually lead to quantitative prediction and guidelines for design and employment. The structure of the IACM makes it clear that the Perron-Frobenius Eigenvalue is a quantifiable metric with which to measure the organization of a networked force. The results of recent experiments presented in Deller, et aI., (2009) indicate that the value of the Perron-Frobenius Eigenvalue is a significant measurement of the performance of an Information Age combat force. This was accomplished through the innovative use of an agent-based simulation to model the IACM and represents an initial contribution towards a new generation of combat models that are net-centric instead of using the current platform-centric approach. This paper describes the intent, challenges, design, and initial results of this agent-based simulation model.

Deller, Sean↗
NASA NTRS1924

Relative efficiency of direct and geared drive propellers

This report is an extension of NACA-TR-168 and has been prepared for the National Advisory Committee for Aeronautics to show the relative values of various direct and geared drives. It is well known that in general a geared-down propeller has higher efficiency than a direct-drive propeller, but the literature on this subject does not present the data in such form that the aeronautical engineer can readily visualize the effect of gearing. This report has been prepared to show the actual net gain or loss in maximum efficiency due to the use of various modifications of the conventional two-bladed, direct-drive propeller. (author)

Diehl, Walter S↗
NASA NTRS2007

Neural Net Safety Monitor Design

The National Aeronautics and Space Administration (NASA) at the Dryden Flight Research Center (DFRC) has been conducting flight-test research using an F-15 aircraft (figure 1). This aircraft has been specially modified to interface a neural net (NN) controller as part of a single-string Airborne Research Test System (ARTS) computer with the existing quad-redundant flight control system (FCC) shown in figure 2. The NN commands are passed to FCC channels 2 and 4 and are cross channel data linked (CCDL) to the other computers as shown. Numerous types of fault-detection monitors exist in the FCC when the NN mode is engaged; these monitors would cause an automatic disengagement of the NN in the event of a triggering fault. Unfortunately, these monitors still may not prevent a possible NN hard-over command from coming through to the control laws. Therefore, an additional and unique safety monitor was designed for a single-string source that allows authority at maximum actuator rates but protects the pilot and structural loads against excessive g-limits in the case of a NN hard-over command input. This additional monitor resides in the FCCs and is executed before the control laws are computed. This presentation describes a floating limiter (FL) concept1 that was developed and successfully test-flown for this program (figure 3). The FL computes the rate of change of the NN commands that are input to the FCC from the ARTS. A window is created with upper and lower boundaries, which is constantly floating and trying to stay centered as the NN command rates are changing. The limiter works by only allowing the window to move at a much slower rate than those of the NN commands. Anywhere within the window, however, full rates are allowed. If a rate persists in one direction, it will eventually hit the boundary and be rate-limited to the floating limiter rate. When this happens, a persistent counter begins and after a limit is reached, a NN disengage command is generated. The tunable metrics for the FL are (1) window size, (2) drift rate, and (3) persistence counter. Ultimate range limits are also included in case the NN command should drift slowly to a limit value that would cause the FL to be defeated. The FL has proven to work as intended. Both high-g transients and excessive structural loads are controlled with NN hard-over commands. This presentation discusses the FL design features and presents test cases. Simulation runs are included to illustrate the dramatic improvement made to the control of NN hard-over effects. A mission control room display from a flight playback is presented to illustrate the neural net fault display representation. The FL is very adaptable to various requirements and is independent of flight condition. It should be considered as a cost-effective safety monitor to control single-string inputs in general.

Larson, Richard R.↗
NASA NTRS2009

Implementation of an Adaptive Controller System from Concept to Flight Test

The National Aeronautics and Space Administration (NASA) at the Dryden Flight Research Center (DFRC) has been conducting flight-test research using an F-15 aircraft (figure 1). This aircraft has been specially modified to interface a neural net (NN) controller as part of a single-string Airborne Research Test System (ARTS) computer with the existing quad-redundant flight control system (FCC) shown in figure 2. The NN commands are passed to FCC channels 2 and 4 and are cross channel data linked (CCDL) to the other computers as shown. Numerous types of fault-detection monitors exist in the FCC when the NN mode is engaged; these monitors would cause an automatic disengagement of the NN in the event of a triggering fault. Unfortunately, these monitors still may not prevent a possible NN hard-over command from coming through to the control laws. Therefore, an additional and unique safety monitor was designed for a single-string source that allows authority at maximum actuator rates but protects the pilot and structural loads against excessive g-limits in the case of a NN hard-over command input. This additional monitor resides in the FCCs and is executed before the control laws are computed. This presentation describes a "floating limiter" (FL) concept that was developed and successfully test-flown for this program (figure 3). The FL computes the rate of change of the NN commands that are input to the FCC from the ARTS. A window is created with upper and lower boundaries, which is constantly "floating" and trying to stay centered as the NN command rates are changing. The limiter works by only allowing the window to move at a much slower rate than those of the NN commands. Anywhere within the window, however, full rates are allowed. If a rate persists in one direction, it will eventually "hit" the boundary and be rate-limited to the floating limiter rate. When this happens, a persistent counter begins and after a limit is reached, a NN disengage command is generated. The tunable metrics for the FL are (1) window size, (2) drift rate, and (3) persistence counter. Ultimate range limits are also included in case the NN command should drift slowly to a limit value that would cause the FL to be defeated. The FL has proven to work as intended. Both high-g transients and excessive structural loads are controlled with NN hard-over commands. This presentation discusses the FL design features and presents test cases. Simulation runs are included to illustrate the dramatic improvement made to the control of NN hard-over effects. A mission control room display from a flight playback is presented to illustrate the neural net fault display representation. The FL is very adaptable to various requirements and is independent of flight condition. It should be considered as a cost-effective safety monitor to control single-string inputs in general.

Larson, Richard R.↗
NASA NTRS1986

Thermally induced stresses in cross-ply composite tubes

An approximate solution for determining stresses in cross-ply composite tubes subjected to a circumferential temperature gradient is presented. The solution is based on the principle of complementary virtual work (PCVW) in conjunction with a Ritz approximation on the stress field and accounts for the temperature dependence of material properties. The PCVW method is compared with a planar elasticity solution using temperature-independent material properties and a Navier approach. The net effect of including temperature-dependent material properties is that the peak absolute values of the stresses are reduced. The dependence of the stresses on the circumferential location is also reduced in comparison with the case of temperature-independent properties.

Hyer, M. W.↗
NASA NTRS1993

A study of fiber volume fraction effects in notched unidirectional SCS-6/Ti-15V-3Cr-3Al-3Sn composite

Notched unidirectional SCS-6/Ti-15-3 composite of three different fiber volume fractions (vf = 0.15, 0.37, and 0.41) was investigated for various room temperature microstructural and material properties including: fatigue crack initiation, fatigue crack growth, and fracture toughness. While the matrix hardness is similar for all fiber volume fractions, the fiber/matrix interfacial shear strength and matrix residual stress increases with fiber volume fraction. The composite fatigue crack initiation stress is shown to be matrix controlled and occurs when the net maximum matrix stress approaches the endurance limit stress of the matrix. A model is presented which includes residual stresses and presents the composite initiation stress as a function of fiber volume fraction. This model predicts a maximum composite initiation stress at vf approximately 0.15 which agrees with the experimental data. The applied composite stress levels were increased as necessary for continued crack growth. The applied Delta(K) values at crack arrest increase with fiber volume fraction by an amount better approximated using an energy based formulation rather than when scaled linear with modulus. After crack arrest, the crack growth rate exponents for vf37 and vf41 were much lower and toughness much higher, when compared to the unreinforced matrix, because of the bridged region which parades with the propagating fatigue crack. However, the vf15 material exhibited a higher crack growth rate exponent and lower toughness than the unreinforced matrix because once the bridged fibers nearest the crack mouth broke, the stress redistribution broke all bridged fibers, leaving an unbridged crack. Degraded, unbridged behavior is modeled using the residual stress state in the matrix ahead of the crack tip. Plastic zone sizes were directly measured using a metallographic technique and allow prediction of an effective matrix stress intensity which agrees with the fiber pressure model if residual stresses are considered. The sophisticated macro/micro finite element models of the 0.15 and 0.37 fiber volume fractions presented show good agreement with experimental data and the fiber pressure model when an estimated effective fiber/matrix debond length is used.

Covey, Steven J.↗
NASA NTRS1986

An assessment of factors which determine the net heating rate of the middle atmosphere

The effects changes in stratospheric ozone concentrations have on photochemical models of the atmosphere are evaluated. The study was spurred by the appearance of excessive stratosphere heating above 40 km in radiative transfer computations. A 20 percent reduction in ozone in the 40-55 m altitude interval would offset the anomalous heating values. Comparisons were made between calculated heating rates and in-situ data that included ozone concentrations. Heating rates decreased 0.4 C/day when clouds were present at the 300 mb level, and increased by 0.3 C/day with clouds at the 80 mb level.

Rosenfield, J. E.↗
NASA NTRS1992

An intracloud lightning parameterization scheme for a storm electrification model

The parameterization of an intracloud lightning discharge has been implemented in the present storm electrification model. The initiation, propagation direction, and termination of the discharge are computed using the magnitude and direction of the electric field vector as the determining criteria. The charge redistribution due to the lightning is approximated assuming the channel to be an isolated conductor with zero net charge over its entire length. Various simulations involving differing amounts of charge transferred and distribution of charges have been done. Values of charge transfer, dipole moment change, and electrical energy dissipation computed in the model are consistent with observations. The effects of the lightning-produced ions on the hydrometeor charges and electric field components depend strongly on the amount of charge transferred. A comparison between the measured electric field change of an actual intracloud flash and the field change due to the simulated discharge shows favorable agreement. Limitations of the parameterization scheme are discussed.

Helsdon, John H., Jr.↗
NASA NTRS1994

Molecular Dynamics of a Water-Lipid Bilayer Interface

We present results of molecular dynamics simulations of a glycerol 1-monooleate bilayer in water. The total length of analyzed trajectories is 5ns. The calculated width of the bilayer agrees well with the experimentally measured value. The interior of the membrane is in a highly disordered fluid state. Atomic density profile, orientational and conformational distribution functions, and order parameters indicate that disorder increases toward the center of the bilayer. Analysis of out-of-plane thermal fluctuations of the bilayer surfaces occurring at the time scale of the present calculations reveals that the distribution of modes agrees with predictions of the capillary wave model. Fluctuations of both bilayer surfaces are uncorrelated, yielding Gaussian distribution of instantaneous widths of the membrane. Fluctuations of the width produce transient thinning defects in the bilayer which occasionally span almost half of the membrane. The leading mechanism of these fluctuations is the orientational and conformational motion of head groups rather than vertical motion of the whole molecules. Water considerably penetrates the head group region of the bilayer but not its hydrocarbon core. The total net excess dipole moment of the interfacial water points toward the aqueous phase, but the water polarization profile is non-monotonic. Both water and head groups significantly contribute to the surface potential across the interface. The calculated sign of the surface potential is in agreement with that from experimental measurements, but the value is markedly overestimated. The structural and electrical properties of the water-bilayer system are discussed in relation to membrane functions, in particular transport of ions and nonelectrolytes across membranes.

Wilson, Michael A.↗
NASA NTRS1981

The transport of trace chemicals by planetary waves in the stratosphere. I Steady waves

When dissipation is present a forced planetary wave will interact with the zonal flow in the stratosphere and cause acceleration of the zonal wind, mean-zonal diabatic heating and net transport of trace chemicals. Quasi-geostrophic scaling is used to derive expressions relating the above quantities to each other and to wave statistics for steady-state conditions and Newtonian cooling. Numerical calculations are presented for stationary wavenumber 1 which indicate that in the stratosphere the effect of the wave on the mean-zonal quantities is 1/5 to 1/20 that required by observations and models. In the mesosphere the calculated value is roughly 1/20 the required size. Reasons for this discrepancy are discussed.

Kurzeja, R. J.↗