SEARCH · Engineering Papers

Results for “mounting configurations”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4

All sources NASA NTRS DOE OSTI

NASA NTRS1972

Radiative heating to the Apollo command module: Engineering prediction and flight measurement

The theory and engineering techniques used for the prediction of the Apollo entry thermal-radiation environment are presented. The radiation predictions are shown to be in satisfactory agreement with the Apollo 4, FIRE 1, and FIRE 2 flight radiometer data. The characteristics and performance of the Apollo flight radiometer and ablator-mounted configuration were determined through arc jet simulation tests.

Ried, R. C., Jr.↗

NASA NTRS1973

Development of a uninterrupted power system: ac and dc to dc converter

This program covered the design, fabrication and testing of an advanced development model uninterrupted power system. The input and output requirements imposed on the power processor were specified such that the unit is electrically interchangeable with existing power systems used by the Federal Aviation Administration in installations which have a history of failure due to electrical transient conditions. Input power is from either of two single-phase ac power sources or batteries with electronic selection and transfer between power sources. Battery reconditioning is automatic when either ac source is present. The output power is rated at 84OW; the nominal output is 24V at 35A. Within the 84OW limit, the regulated output voltage is adjustable from 22V to 30Vdc. Protection against continuous overloading or short circuit is provided. The unit is packaged in a standard 19-inch rack mount configuration with 7-inch panel height. Controls are on the front panel with power input and output through connectors on the rear surface. Cooling is by free convection from fin areas located on the side and rear panels. The packaged unit weighs 52.8 lbs., which can be reduced significantly if a three-phase ac power source is used.

Cronin, D. L.↗

NASA NTRS1972

Space shuttle system program definition. Volume 1: Executive summary

A study for the selection of a low cost shuttle system for design and development was conducted. The objective of the final study was to examine and penetrate the major technical and cost issues affecting the choice of the following: (1) liquid propulsion recoverable or solid propulsion recoverable booster, (2) parallel burn/parallel mount or series burn/tandem mount configurations, and (3) payload weight and payload bay size of the orbiter. The matrix of program options which were considered in the study is developed.

Source record↗

NASA NTRS1975

Preliminary vibration, acoustic, and shock design and test criteria for components on the HEAO-A spacecraft

These vibration, acoustic, and shock specifications provide the qualification test criteria for spacecraft components and subassemblies and for the High Energy Astronomy Observatory (HEAO-A) experiments. The HEAO-A was divided into zones and subzones to obtain simple component groupings. Zones are designated primarily to assist in determining the applicable specification. A Subzone is available for use when the location of the component is known but component design and weight are not well defined. When the location, weight, and mounting configuration of the component are known, the appropriate Subzone weight ranges are available. Experiment and specific component specifications are available.

Source record↗

NASA NTRS1975

Preliminary vibration, acoustic, and shock design and test criteria for components on the HEAO-C spacecraft

The vibration, acoustic, and shock specification test criteria for spacecraft components and subassemblies and for the high Energy Astronomy Observatory (HEAO-C) experiments are presented. The HEAO-C was divided into zones and subzones to obtain simple component groupings. Zones are designated primarily to assist in determining the applicable specification. A subzone (general specification) is available for use when the location of the component is known but component design and weight are not well defined. When the location, weight, and mounting configuration of the component are known, the appropriate subzone weight ranges (-A, -B, etc. ) are available. Experiment and specific component specifications are available.

Source record↗

NASA NTRS1978

Adding through-bolt holes to pin-fin cold plates

Spot-welding technique is less expensive than secondary-brazing and electron-beam methods. With procedure, standard plates can be modified in quantity for various mounting configurations without need for special tooling.

Ruppe, E. P.↗

NASA NTRS1976

Preliminary vibration, acoustic, and shock design and test criteria for components on the SRB, ET, and SSME

Specifications for vibration, acoustic and shock design for components and subassemblies on the External Tank (ET), Solid Rocket Booster (SRB), and Space Shuttle Main Engine (SSME). Included are vibration, acoustic, shock, transportation, handling, and acceptance test requirements and procedures. The space shuttle ET, SRB, and SSME have been divided into zones and subzones. Zones are designated primarily to assist in determining the applicable specifications. A subzone (General Specification) is available for use when the location of the component is known but component design and weight are not well defined. When the location, weight, and mounting configuration of the component are known, specifications for appropriate subzone weight ranges are available. Criteria for some specific components are also presented.

Source record↗

NASA NTRS1976

Summary of studies for a solar optical telescope in space: 1968-1976

The primary objective of this review is to tabulate the basic recommendations of several solar telescope studies. A primary matrix, listing some of the basic optical parameters, was compiled and forms the basis for a table. From this table it is apparent that a strong consensus exists on the configuration of the telescope and on its fundamental dimensionless parameters. Other tables presented in this document address the basic approach of each study to the telescope design as well as to the design of critical subsystems. These subsystem problems include the material, coating, configuration, mounting, launch locks, and thermal control of the primary mirror, the structure of the main telescope and the instrument bay, the mechanisms for radiation rejection, thermal control, and meteoroid shielding, and methods of maintaining image quality by proper alignment and by image motion compensation.

Bremer, J.↗

NASA NTRS1978

Thermal and other tests of photovoltaic modules performed in natural sunlight

The bulk of the testing was the characterization of twenty-nine modules according to their nominal operating cell temperature (NOCT) and the effect on NOCT of changes in module design, various residential roof mounting configurations, and dirt accumulation. Other tests, often performed parallel with the NOCT measurements, evaluated the improvement in electrical performance by cooling the modules with water and by channeling the waste heat into a phase change material (wax). Electrical degradation resulting from the natural marriage of photovoltaic and solar water heating modules was also demonstrated. Cost effectiveness of each of these techniques are evaluated in light of the LSA cost goal of $0.50 per watt.

Stultz, J. W.↗

NASA NTRS1979

Effect of steady-state temperature distortion and combined distortion on inlet flow to a turbofan engine

Flow angle, static pressure, total temperature and total pressure were measured in the inlet duct upstream of a turbofan engine operating with temperature distortion or combined pressure-temperature distortion. Such measurements are useful in the evaluation of analytical models of inlet distortion. A rotating gaseous-hydrogen burner and a circumferential 180 degrees-extent screen configuration mounted on a rotatable assembly generated the distortions. Reynolds number index was maintained at 0.5 and engine corrected low-rotor speeds were held at 6000 and 8600 rpm. The measurements showed that at the entrance to the engine, flow angle was largest in the hub region. As flow approached the engine, yaw angle (circumferential variation) increased and pitch angle (radial variation) decreased. The magnitude of static-pressure distortion measured along the inlet-duct and extended bullet nose walls increased exponentially as flow approached the engine.

Soeder, R. H.↗

NASA NTRS1979

Automated biowaste sampling system feces monitoring system

The Feces Monitoring System (FMS) Program designed, fabricated, assembled and tested an engineering model waste collector system (WCS) to be used in support of life science and medical experiments related to Shuttle missions. The FMS design was patterned closely after the Shuttle WCS, including: interface provisions; mounting; configuration; and operating procedures. These similarities make it possible to eventually substitute an FMS for the Shuttle WCS of Orbiter. In addition, several advanced waste collection features, including the capability of real-time inertial fecal separation and fecal mass measurement and sampling were incorporated into the FMS design.

Hunt, S. R.↗

NASA NTRS1979

Residential photovoltaic module and array requirements study, appendices

Regional building code variations, federal and city codes, and the national electric code are reviewed for their possible effects on the design of photovoltaic modules. Problems that photovoltaic arrays may impose on the insurability of residences are also discussed. Mounting configurations are developed for the modules, and grounding, wiring, terminal, and voltage requirements are established. Installation and materials costs are presented along with performance criteria.

Nearhoof, S. L.↗

NASA NTRS1981

Preliminary vibration, acoustic, and shock design and test criteria for components on the Lightweight External Tank (LWT)

The Space Shuttle LWT is divided into zones and subzones. Zones are designated primarily to assist in determining the applicable specifications. A subzone (general Specification) is available for use when the location of the component is known but component design and weight are not well defined. When the location, weight, and mounting configuration of the component are known, specifications for appropriate subzone weight ranges are available. Along with the specifications are vibration, acoustic, shock, transportation, handling, and acceptance test requirements and procedures. A method of selecting applicable vibration, acoustic, and shock specifications is presented.

Source record↗

NASA NTRS1981

Structural dynamics verification facility study

The need for a structural dynamics verification facility to support structures programs was studied. Most of the industry operated facilities are used for highly focused research, component development, and problem solving, and are not used for the generic understanding of the coupled dynamic response of major engine subsystems. Capabilities for the proposed facility include: the ability to both excite and measure coupled structural dynamic response of elastic blades on elastic shafting, the mechanical simulation of various dynamical loadings representative of those seen in operating engines, and the measurement of engine dynamic deflections and interface forces caused by alternative engine mounting configurations and compliances.

Kiraly, L. J.↗

NASA NTRS1983

Double arch mirror study. Part 2: Engineering analysis report

A method of mounting a cryogenically cooled, lightweight, double arch, class mirror for infrared, astronomical telescopes was developed. A 50 cm, fused silica mirror was modified for use in a new mount configuration. The flexures and the finite element analysis of the mirror stresses are reported.

Iraninejad, B.↗

NASA NTRS1984

Advanced Gas Turbine (AGT) powertrain system development for automotive applications

Rotor dynamic instability investigations were conducted. Forward ball bearing hydraulic mount configurations were tested with little effect. Trial assembly of S/N 002 ceramic engine was initiated. Impeller design activities were completed on the straight line element (SLE) blade definition to address near-net-shape powder metal die forging. Performance characteristics of the Baseline Test 2A impeller were closely preserved. The modified blading design has been released for tooling procurement. Developmental testing of the diffusion flame combustor (DFC) for initial use in the S/N 002 2100 F ceramic structures engine was completed. A natural gas slave preheater was designed and fabricated. Preliminary regenerator static seal rig testing showed a significant reduction in leakage and sensitivity to stack height. Ceramic screening tests were completed and two complete sets of ceramic static structures were qualified for engine testing. Efforts on rotor dynamics development to resolve subsynchronous motion were continued.

Source record↗

NASA NTRS1984

Predicting photothermal field performance

Photothermal field performance in flat plate solar collectors was predicted. An analytical model which incorporates the measured dependency between transmittance loss and UV and temperature exposure levels was developed. The model uses SOLMET weather data extrapolated to 30 years for various sites and module mounting configurations. It is concluded that the temperature is the key to photothermally induced transmittance loss. The sensitivity of transmittance loss to UV level is nonlinear with minimum in curve near one sun. The ethylene vinyl acetate (EVA) results are consistent with 30 year life allocation.

Gonzalez, C. C.↗

NASA NTRS1988

Space shuttle solid rocket motor Profile Measuring Device (PMD)

The SRM PMD is an electromechanical tool used for measuring and recording the profile and diameters of the solid rocket motor segments, both Tang and Clevis ends. This system consists of a crossbeam assembly that mounts to the SRM segment using the existing assembly pin holes. The mounting configuration is such that the tool can be used to measure Clevis up/Tang down or Clevis up/Tang down. The testing and calibration of the PMD is described.

Redmon, John↗