Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “model deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Fracture analysis of transverse crack-tip and free-edge delamination in laminated composites

A shear deformation model including hygrothermal effects is developed for the analysis of local delaminations originating from transverse cracks in 90-deg plies located in and around the laminate midplane. A sublaminate approach is used and the model is applied to (+/- 25/90n)s T300/934 graphite/epoxy laminates for n values between 0.5 and 8, along with previously developed edge-delamination shear-deformation models. Critical loads and delamination modes are identified and compared with experimental results. Hygrothermal effects are included in all the models to make the comparisons realistic.

Armanios, Erian A.↗
NASA NTRS1986

The National Transonic Facility

The National Transonic Facility, NTF, is a high Reynolds Number facility where the increase in Reynolds Number is obtained by operating at high pressures and low temperatures. Liquid nitrogen is allowed to vaporize, making gaseous nitrogen the test medium with temperatures extending down to approximately 100 degrees Kelvin. These factors have created unique, new challenges to those developing sensors and instrumentation. Pressure vessels, thermal enclosures or elaborate temperature compensations schemes, are needed for environmental protection and special materials are needed for sensors and model fabrication. The need for a new measurement, model deformation, was also created. An extensive program to develop the unique sensors and instrumentation was initiated. The data acquisition system and systems to measure aerodynamic forces and pressures, model attitude, and model deformation, are discussed.

Holmes, H. K.↗
NASA NTRS1998

Summary Report of the First International Symposium on Strain Gauge Balances and Workshop on AoA/Model Deformation Measurement Techniques

The first International Symposium on Strain Gauge Balances was sponsored under the auspices of the NASA Langley Research Center (LaRC), Hampton, Virginia. Held at the LaRC Reid Conference Center, the Symposium provided an open international forum for presentation, discussion, and exchange of technical information among wind tunnel test technique specialists and strain gauge balance designers. The Symposium also served to initiate organized professional activities among the participating and relevant international technical communities. The program included a panel discussion, technical paper sessions, tours of local facilities, and vendor exhibits. Over 130 delegates were in attendance from 15 countries. A steering committee was formed to plan a second international balance symposium tentatively scheduled to be hosted in the United Kingdom in 1998 or 1999. The Balance Symposium was followed bv the half-day, Workshop on Angle of Attack and Model Deformation on the afternoon of October 25. The thrust of the Workshop was to assess the state of the art in angle of attack (AoA) and model deformation measurement techniques and to discuss future developments.

Tripp, John S.↗
NASA NTRS1999

Summary Report of the First International Symposium on Strain Gauge Balances and Workshop on AoA/Model Deformation Measurement Techniques

The first International Symposium on Strain Gauge Balances was sponsored under the auspices of the NASA Langley Research Center (LaRC), Hampton, Virginia during October 22-25, 1996. Held at the LaRC Reid Conference Center, the Symposium provided an open international forum for presentation, discussion, and exchange of technical information among wind tunnel test technique specialists and strain gauge balance designers. The Symposium also served to initiate organized professional activities among the participating and relevant international technical communities. The program included a panel discussion, technical paper sessions, tours of local facilities, and vendor exhibits. Over 130 delegates were in attendance from 15 countries. A steering committee was formed to plan a second international balance symposium tentatively scheduled to be hosted in the United Kingdom in 1998 or 1999. The Balance Symposium was followed by the half-day Workshop on Angle of Attack and Model Deformation on the afternoon of October 25. The thrust of the Workshop was to assess the state of the art in angle of attack (AoA) and model deformation measurement techniques and to discuss future developments.

Tripp, John S.↗
NASA NTRS1999

Advances in Projection Moire Interferometry Development for Large Wind Tunnel Applications

An instrument development program aimed at using Projection Moire Interferometry (PMI) for acquiring model deformation measurements in large wind tunnels was begun at NASA Langley Research Center in 1996. Various improvements to the initial prototype PMI systems have been made throughout this development effort. This paper documents several of the most significant improvements to the optical hardware and image processing software, and addresses system implementation issues for large wind tunnel applications. The improvements have increased both measurement accuracy and instrument efficiency, promoting the routine use of PMI for model deformation measurements in production wind tunnel tests.

Fleming, Gary A.↗
NASA NTRS1977

Solid propellant rocket motor internal ballistics performance variation analysis, phase 3

Results of research aimed at improving the predictability of off nominal internal ballistics performance of solid propellant rocket motors (SRMs) including thrust imbalance between two SRMs firing in parallel are reported. The potential effects of nozzle throat erosion on internal ballistic performance were studied and a propellant burning rate low postulated. The propellant burning rate model when coupled with the grain deformation model permits an excellent match between theoretical results and test data for the Titan IIIC, TU455.02, and the first Space Shuttle SRM (DM-1). Analysis of star grain deformation using an experimental model and a finite element model shows the star grain deformation effects for the Space Shuttle to be small in comparison to those of the circular perforated grain. An alternative technique was developed for predicting thrust imbalance without recourse to the Monte Carlo computer program. A scaling relationship used to relate theoretical results to test results may be applied to the alternative technique of predicting thrust imbalance or to the Monte Carlo evaluation. Extended investigation into the effect of strain rate on propellant burning rate leads to the conclusion that the thermoelastic effect is generally negligible for both steadily increasing pressure loads and oscillatory loads.

Sforzini, R. H.↗
NASA NTRS1988

Nonlinear modeling and estimation of slew induced structural deformations

A model of the nonlinear dynamics of a deformable maneuvering multibody system is described, whereby elastic deformation are modeled by restoring forces and dissipative forces at point mass appendages. This model is brought into bilinear form. Estimation of deformations occasioned by rapid slewing maneuvers is carried out by a filter based on a globally equivalent linear model of the bilinear dynamics, and is shown to be an improvement over the extended Kalman filter. To further alleviate the computational burden, the estimated deformation state is propagated between observations by a low dimensional operator spline interpolator of bilinear system Volterra series, which is easily implemented.

Dwyer, T. A. W., III↗
NASA NTRS1973

Topography on satellite surfaces and the shape of asteroids.

Consideration of the topography and shape of incompressible, nonrotating, isothermal, spherical objects as an approach to the study of the topography and shape of smaller planetary bodies. A static model and a creep deformation model are applied in the process. Factors and forces which may have a bearing on the geometry and topography of small planetary bodies are discussed.

Johnson, T. V.↗
NASA NTRS2002

Uncertainty of Videogrammetric Techniques used for Aerodynamic Testing

The uncertainty of videogrammetric techniques used for the measurement of static aeroelastic wind tunnel model deformation and wind tunnel model pitch angle is discussed. Sensitivity analyses and geometrical considerations of uncertainty are augmented by analyses of experimental data in which videogrammetric angle measurements were taken simultaneously with precision servo accelerometers corrected for dynamics. An analysis of variance (ANOVA) to examine error dependence on angle of attack, sensor used (inertial or optical). and on tunnel state variables such as Mach number is presented. Experimental comparisons with a high-accuracy indexing table are presented. Small roll angles are found to introduce a zero-shift in the measured angles. It is shown experimentally that. provided the proper constraints necessary for a solution are met, a single- camera solution can he comparable to a 2-camera intersection result. The relative immunity of optical techniques to dynamics is illustrated.

Burner, A. W.↗
NASA NTRS1986

Testing experience with the National Transonic Facility

The National Transonic Facility (NTF) was designed for high productivity within the constraints of operation in a cryogenic environment using nitrogen as a test gas. This environment has a significant impact on overall operation. The facility has been operational since August, 1984, and experience has been gained with respect to the facility operation and aerodynamic testing. This paper describes the experience to date with the pretest preparation and testing operations including liquid N2 supply constraints. The instrumentation system is discussed including force, pressure, angle of attack, and model deformation measurements. Selected data from models tested in the NTF, and a status of the static calibration, are also presented.

Fuller, D. E.↗
NASA NTRS1989

Digital Video Measurements Of Wing Deflections In A Wind Tunnel

Solid-state cameras and computer-controlled image-acquisition system measure deformations of wind-tunnel models. Digital video model-deformation (VMD) system includes solid-state-array cameras and digital image-acquisition system controlled by personal computer. Eliminates both vibration-induced distortion associated with tube cameras and manual processing of video hardcopy images necessary in earlier version. AT-class personal computer controls two commercially available image-capture boards ganged to capture simultaneously two video images, each 752 picture elements wide and 480 picture elements high, in one-thirtieth of second. Video images digitized into 256 gray levels. Figure block diagram of system.

Burner, Alpheus W.↗
NASA NTRSDate not supplied

Application of the MAT 213 Composite Impact Model to NASA Problems of Interest

A material model has been developed which incorporates several key capabilities which have been identified as lacking in currently available composite impact models. The material model utilizes experimentally based tabulated input to define the evolution of plasticity and damage as opposed to specifying discrete input parameters (such as modulus and strength). The material model has been implemented into LS-DYNA® as MAT 213. The model can simulate the nonlinear deformation, damage and failure that takes place in a composite under dynamic loading conditions. The deformation model utilizes an orthotropic plasticity formulation. For the damage model, the nonlinear unloading response that is observed prior to the point where the peak stress is reached can be simulated, as well as the stress degradation response that occurs after the peak stress is reached. A variety of failure models, including a generalized tabulated failure model which facilitates the utilization of general failure surfaces, have been implemented into MAT 213. Recent studies at NASA have concentrated on using MAT 213 to analyze both the impact and crush response of a variety of laminated and textile architectures. Several of these studies will be discussed in the presented paper. For example, a woven carbon/Kevlar composite is currently being examined for use in an energy absorber system for rotorcraft structures. MAT 213 analyses have been conducted to examine the ability of the model to accurately simulate the dynamic crush response of this material. Studies are also being conducted to examine the ability of MAT 213 to simulate the ballistic impact response of representative laminated and woven thermoplastic and thermoset matrix composites. NASA efforts are also concentrated on developing methods and processes for improving characterization methods and developing “best practices” for using MAT 213, a summary of which will be discussed in the paper.

Polymer Matrix Composites↗
NASA NTRS1984

Hygrothermal effects on stresses and deformations in a bonded fiber-reinforced plastic/aluminum system

The hygrothermal effect on time dependent mechanical behavior of a model of nonsymmetrical bonded fiber-reinforced plastic (FRP)/aluminum system was investigated analytically. It was found that a linear viscoelastic closed form solution is sufficient for the prediction model deformations for short periods of time and small strains, while a numerical finite-element solution is preferable for determining adhesive stresses and deformational behavior of the model at any time. The thermoelastic numerical solution shows a certain decrease with time of adhesive stresses, which does not seem to affect significantly the global deformations of the model. On the other hand, it was found that the presence of moisture within the polymeric adhesive layer causes significant decrease in adhesive stresses, which affects deformational changes with time, far beyond the level predicted by the static solution.

Yaniv, G.↗
NASA NTRS2004

Assessing Videogrammetry for Static Aeroelastic Testing of a Wind-Tunnel Model

The Videogrammetric Model Deformation (VMD) technique, developed at NASA Langley Research Center, was recently used to measure displacements and local surface angle changes on a static aeroelastic wind-tunnel model. The results were assessed for consistency, accuracy and usefulness. Vertical displacement measurements and surface angular deflections (derived from vertical displacements) taken at no-wind/no-load conditions were analyzed. For accuracy assessment, angular measurements were compared to those from a highly accurate accelerometer. Shewhart's Variables Control Charts were used in the assessment of consistency and uncertainty. Some bad data points were discovered, and it is shown that the measurement results at certain targets were more consistent than at other targets. Physical explanations for this lack of consistency have not been determined. However, overall the measurements were sufficiently accurate to be very useful in monitoring wind-tunnel model aeroelastic deformation and determining flexible stability and control derivatives. After a structural model component failed during a highly loaded condition, analysis of VMD data clearly indicated progressive structural deterioration as the wind-tunnel condition where failure occurred was approached. As a result, subsequent testing successfully incorporated near- real-time monitoring of VMD data in order to ensure structural integrity. The potential for higher levels of consistency and accuracy through the use of statistical quality control practices are discussed and recommended for future applications.

Spain, Charles V.↗
NASA NTRS2014

Pressure Sensitive Paint Applied to Flexible Models Project

One gap in current pressure-measurement technology is a high-spatial-resolution method for accurately measuring pressures on spatially and temporally varying wind-tunnel models such as Inflatable Aerodynamic Decelerators (IADs), parachutes, and sails. Conventional pressure taps only provide sparse measurements at discrete points and are difficult to integrate with the model structure without altering structural properties. Pressure Sensitive Paint (PSP) provides pressure measurements with high spatial resolution, but its use has been limited to rigid or semi-rigid models. Extending the use of PSP from rigid surfaces to flexible surfaces would allow direct, high-spatial-resolution measurements of the unsteady surface pressure distribution. Once developed, this new capability will be combined with existing stereo photogrammetry methods to simultaneously measure the shape of a dynamically deforming model in a wind tunnel. Presented here are the results and methodology for using PSP on flexible surfaces.

model deformation↗
NASA NTRS2021

Application of a Developmental Composite Material Model to Predict the Crush Response of Two Energy Absorbers

In 2012, a consortium was formed with the goal of creating a new composite material model capable of predicting the wide range of properties, accumulated damage behavior, and the many different types of failure in composites under impact loading. The material model was developed for execution in the commercially available nonlinear, explicit transient dynamic finite element code, LS-DYNA®. This material model incorporates three sub-models: deformation, damage, and failure. In addition, the model accounts for strain rate and temperature effects and relies heavily on the input of tabulated material response data. The model is designated *MAT_COMPOSITE_TABULATED_PLASTICITY_DAMAGE, or *MAT_213. Initially, *MAT_213 was developed for use with solid elements only; however, a thin shell element formulation for *MAT_213 has been adapted recently. The objective of this project was to find a suitable modeling example to investigate the capabilities and performance of *MAT_213. In 2012, two composite energy absorbers were designed and evaluated at NASA Langley Research Center through multi-level testing and simulation. The first was a conical-shaped energy absorber, designated the conusoid, which consisted of four layers of hybrid carbon-Kevlar® plain-weave fabric oriented at [+45°/-45°/-45°/+45°] with respect to the vertical direction. The second was a sinusoidal-shaped energy absorber, designated the sinusoid, which consisted of hybrid carbon-Kevlar® plain-weave fabric face sheets, two layers for each face sheet oriented at ±45° with respect to the vertical direction, and a closed-cell ELFOAM® P200 polyisocyanurate foam core. Finite element models were developed of the energy absorbers and simulations were performed using LS-DYNA®. In this paper, the development of a *MAT_213 model of a hybrid carbon-Kevlar® plain-weave fabric is presented. Next, comparisons with material characterization tests are presented. Then, test-analysis results are documented for each energy absorber as comparisons of time-history responses, as well as predicted and experimental structural deformations and progressive damage under impact loading using the *MAT_213 material model. Since a prior *MAT_58, or *MAT_LAMINATED_COMPOSITE_FABRIC material model was used in previous simulations of the energy absorbers, comparisons are made between *MAT_58 and *MAT_213 model predictions with test data. Finally, the paper includes a comprehensive list of “lessons learned,” in which a series of parametric studies are documented that were performed to investigate specific issues related to the material model. These “lessons learned” are included in hopes that they may help future *MAT_213 users.

crashworthiness, LS-DYNA transient dynamic simulat↗