Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microwave devices”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Thermal Modulation of Gigahertz Surface Acoustic Waves on Lithium Niobate

Surface-acoustic-wave (SAW) devices have a wide range of applications in microwave signal processing. Microwave SAW components benefit from higher quality factors and much smaller crosstalk when compared to their electromagnetic counterparts. Efficient routing and modulation of SAWs are essential for building large-scale and versatile acoustic wave circuits. Here, we demonstrate integrated thermoacoustic modulators using two SAW platforms: bulk lithium niobate and thin-film lithium niobate on sapphire. In both approaches, the gigahertz-frequency SAWs are routed by integrated acoustic waveguides, while on-chip microheaters are used to locally change the temperature, and thus, control the phase of the SAW. Using this approach, we achieve phase changes of over 720° with the responsibility of 2.6°/mW for bulk lithium niobate and 0.52°/mW for lithium niobate on sapphire. Furthermore, we demonstrate amplitude modulation of SAWs using acoustic Mach-Zehnder interferometers. Our thermoacoustic modulators can enable reconfigurable acoustic signal processing for next-generation wireless communications and microwave systems.

42 ENGINEERING↗
DOE OSTI2026

Investigation of coherence of niobium-based resonators enabled by a fast-sealing microwave cavity

Resonators and qubits with a niobium (Nb) base metal layer achieve some of the highest coherence times in superconducting quantum devices. The performance of such devices is often limited by loss associated with two-level systems, which are found primarily at material surfaces and interfaces. The metal-air (MA) interface is a major contributor to device loss. In this work, we develop a fast-sealing microwave cavity that enables devices to be placed under vacuum within five minutes of oxide removal, thereby significantly reducing the MA interface loss compared to common device processing and packaging approaches. Using coplanar stripline resonators, we demonstrate that devices sealed in such a cavity exhibit internal quality factors exceeding one million at single-photon power. After re-exposure to air, the devices show downward resonance frequency shifts and quality factor degradations, quantitatively consistent with a model of Nb oxide regrowth. The fast-sealing microwave cavity provides a practical and consistent method to mitigate MA interface loss and sustain high coherence in Nb devices, and establishes a controlled platform for studying metal oxide regrowth kinetics and dielectric properties, the understanding of which is critical to achieving high coherence in superconducting quantum devices.

Zhang, C. [Waterloo U., IQC; Waterloo U.]↗
DOE OSTI2023

Optomechanical ring resonator for efficient microwave-optical frequency conversion

Phonons traveling in solid-state devices are emerging as a universal excitation for coupling different physical systems. Phonons at microwave frequencies have a similar wavelength to optical photons in solids, enabling optomechanical microwave-optical transduction of classical and quantum signals. It becomes conceivable to build optomechanical integrated circuits (OMIC) that guide both photons and phonons and interconnect photonic and phononic devices. Here, we demonstrate an OMIC including an optomechanical ring resonator (OMR), where co-resonant infrared photons and GHz phonons induce significantly enhanced interconversion. The platform is hybrid, using wide bandgap semiconductor gallium phosphide (GaP) for waveguiding and piezoelectric zinc oxide (ZnO) for phonon generation. The OMR features photonic and phononic quality factors of >1 × 10 5 and 3.2 × 10 3 , respectively. The optomechanical interconversion between photonic modes achieved an internal conversion efficiency $η_i$ = (2.1 ± 0.1)% and a total device efficiency $η_{tot}$ = 0.57 x 10 -6 at a low acoustic pump power of 1.6 mW. The efficient conversion in OMICs enables microwave-optical transduction for quantum information and microwave photonics applications.

42 ENGINEERING↗
DOE OSTI2025

Local microwave sensing of excitons and their electrical environment

Excitons in atomically thin transition metal dichalcogenides (TMDs) possess intriguing optical properties, drawing interest for both technology and fundamental research. However, as the demands for nanodevice applications and the exploration of fundamental physics push toward smaller, subwavelength scales, studying them locally is challenging. In this work, we introduce a cryogenic scanning probe photoelectrical sensing technique, termed exciton-resonant microwave impedance microscopy (ER-MIM), to measure the excitonic responses in a monolayer MoSe 2 device at 1.5K. From the microwave signal changes, we identify exciton polarons and their Rydberg states. Building on these observations, we systemically reveal the local and nonlocal effects of carrier density, inhomogeneous electric fields, as well as dielectric screening on excitons, beyond the reach of conventional probes. By further integrating deep learning techniques, we precisely extracted the electrical parameters surrounding excitons, demonstrating a quantified, exciton-assisted nanoscale electrometry. Our results provide new insight into exciton-environment interactions, establish ER-MIM as a powerful optoelectronic sensing platform, and open avenues for exciton-based quantum control and device technologies.

scanning probe microscopy↗
DOE OSTI2022

Material Plasma Exposure eXperiment (MPEX) High Heat Flux Bellows for Component Alignment in High Microwave Environment

The Material Plasma Exposure eXperiment (MPEX) device is a linear plasma device developed to perform plasma material interaction experiments under the conditions prototypic of a fusion reactor divertor. MPEX has multiple systems that must be precisely aligned to the plasma axis, including an electron cyclotron heating system that emits up to 400 kW of microwave power into the vacuum vessel. Five distinct systems require precise alignment on the MPEX device, thus requiring four bellows, all of which are adjacent to the plasma at a relatively high heat flux of approximately 47 kW/m2 and microwave power regions. The MPEX high heat flux bellows (HHFB) is designed to deliver 6 degrees of freedom positioning. The HHFB includes titanium–zirconium–molybdenum (TZM) inserts that are brazed into a Glidcop AL-15 body using a high-temperature braze alloy, thus blocking direct line of sight to an edge-welded bellows from the plasma and microwave screen to block microwaves from the bellows. Further, a custom ConFlat knife edge is machined into the Glidcop AL-15, so the vacuum flanges do not need a braze or weld joint on the vacuum interface. Fingerstock or copper mesh is used to restrict microwave power from entering the interstitial space between the water-cooled Glidcop AL-15 body and edge-welded bellows. Glidcop AL-15 was selected as the material of choice for the water-cooled body because it can maintain mechanical integrity at elevated temperatures, and it also allows for a high-temperature braze. TZM was selected for its machinability and compatibility with vacuum and plasma requirements. A test article is also being considered for a similarly shaped component, the MPEX limiter, that will demonstrate the integrity of the braze joint under high thermal load. Results from this testing will be extrapolated to deduce the lifetime and integrity of the HHFB design.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

A microwave SQUID multiplexer optimized for bolometric applications

A microwave SQUID (superconducting quantum interference device) has been optimized for reading out large arrays of superconducting transition-edge sensor (TES) bolometers. We present the scalable cryogenic multiplexer chip design that may be used to construct an 1820-channel multiplexer for the 4-8 GHz rf band. The key metrics of yield, sensitivity, and crosstalk are determined through measurements of 455 readout channels, which span 4-5 GHz. The median white-noise level is 45 pA/ $\sqrt{Hz}$, evaluated at 2 Hz, with a 1/f knee ≤ 20 mHz after common-mode subtraction. The white-noise level decreases the sensitivity of a TES bolometer optimized for detection of the cosmic microwave background at 150 GHz by only 3%. The measured crosstalk between any channel pair is ≤ 0.3%.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Josephson Junctions and Cosmic Microwave Background

The implementation of utilizing superconducting quantum interference device (SQUID) readout for constant voltage biased transition edge sensors (TES) has enabled the detection of the infinitesimal fluctuation in cosmic microwave background (CMB). The properties of the fluctuations will provide us the information of the universe at the time that this light was first emitted. In short, by measuring the CMB today, we learn about the distant, ancient universe—how the universe began, what it is made of, and how it evolved to its current state. Over the past 20 years, we have achieved many successful CMB measurements with Josephson junctions. Brian, I extend my congratulations on your eight decades of life—Happy 80th birthday!

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2026

Simplifying the Chemical Design of Nonfused-Ring Electron Acceptors─Lessons Learned from Thienothiophene and Benzodithiophene Cores

Nonfused-ring electron acceptors (NFREA)s have been proposed as alternatives to fused-ring acceptors in organic photovoltaics (OPV)s. The simpler molecular design of NFREAs results in a reduced synthetic complexity, potentially lowering manufacturing costs, and easier access to desired optoelectronic properties by structural modifications. However, they have not seen the same rise in popularity as fused nonfullerene acceptors (NFA)s due to their lower performances in devices. In this work, we explore structure–property relationships of three NFREA molecules based on thieno[3,2-b]thiophene (TT) and benzo[1,2-b:4,5-b′]dithiophene (BDT) cores and malononitrile functionalized-isatin end group acceptors. We describe their synthetic routes, computational analysis, and photophysical and electronic properties. Here, we investigated the effect of changing the core from TT to BDT on electronic properties of the molecules─a result of raising/lowering of the frontier molecular orbital (FMO) levels. We also explored the effect of branched vs nonbranched alkyl groups on the morphological and blend-capabilities in bulk heterojunction (BHJ) OPV devices. These effects were then reflected in the overall device performances, primarily due to favorable FMO energy alignment between the NFREA and polymer. To investigate the behavior of the excited states of the NFREAs within the active layer of the devices, we performed time-resolved microwave conductivity and transient absorption experiments, which confirmed that the TT molecules exhibited very low conductance while the BDT molecule showed moderate photoconductance. Our combined theoretical, synthetic, device, and charge carrier dynamics studies of these materials reveal the central role that structure–property relationships play in future molecular designs of NFREAs that can perform as well as their fused counterparts.

14 SOLAR ENERGY↗
DOE OSTI2021

Large microwave inductance of granular boron-doped diamond superconducting films

Boron-doped diamond granular thin films are known to exhibit superconductivity with an optimal critical temperature of T c =7.2 K. Here, we report the measured in-plane complex surface impedance of boron-doped diamond films in the microwave frequency range using a resonant technique. Experimentally measured inductance values are in good agreement with estimates obtained from the normal state sheet resistance of the material. Additionally, the magnetic penetration depth temperature dependence is consistent with that of a fully gapped s-wave superconductor. Boron-doped diamond films should find application where high kinetic inductance is needed, such as microwave kinetic inductance detectors and quantum impedance devices.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2023

Multicolored microwave absorbers with dynamic frequency modulation

Microwave-absorbing materials are extensively used in intelligent electronic devices and stealth technologies where the ability to dynamically adjust microwave-absorbing capacity in response to specific requirements is vitally important. Herein, we report a new approach for constructing dynamically tunable microwave absorbers with ultrawide tunable frequency ranges that are simultaneously endowed with vibrant structural colors. Here, the methodology produces structural colors and adjusts absorption properties by constructing ZnO coatings with precisely adjustable thicknesses on a polypyrrole/melamine foam (PPy/MF) surface by atomic layer deposition (ALD) in conjunction with a pressure-driven strategy that regulates the compression ratio. The electrical conductivity, electromagnetic parameters, thickness, and pore size of the ZnO-coated PPy/MF (ZnO/PPy/MF) are effectively adjusted, and simply applying external pressure widens the tunable frequency range and the effective absorption bandwidth. As a result, the effective absorption frequency of ZnO/PPy/MF is dynamically adjustable from the S band to the Ku band, thereby covering 94.3% of the entire microwave spectrum. Moreover, the brilliant and uniform structural colors of ZnO/PPy/MF, which span various color categories, are precisely regulated by tuning the thickness of the ZnO coating by adjusting the number of ALD cycles. ZnO/PPy/MF is strongly hydrophobic, which endows it with remarkable self-cleaning properties. Therefore, ZnO/PPy/MF provides a conceptually novel platform for the development of next-generation smart microwave-absorbing materials due to its integrated dynamic frequency-regulating ability, brilliant structural coloration, and self-cleaning features.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Scanning tunneling microscopy and spectroscopy characterization of Nb films for quantum applications

Niobium thin films are key components of superconducting microwave resonators. Interest in these devices has increased dramatically because of their application in quantum systems. Despite tremendous effort to improve their performance, loss mechanisms are still not well understood. Nb/substrate and Nb/air interfaces are likely culprits in contributing to decoherence and ultimately limiting the performance of superconducting devices. Here, we investigate the Nb/substrate interface by studying the effect of hydrogen-passivated H:Si(111) substrates on the local superconducting properties of ∼40 nm thick Nb films compared to Nb films grown on typical Si(001) substrates. Specifically, low-temperature scanning tunneling microscopy and spectroscopy are employed to compare nanoscale material properties. Further, the atomically flat monohydride H:Si(111) substrates are found to yield a smoother and less defective interface with the Nb film. Correspondingly, the Nb films grown on H:Si(111) substrates present more uniform superconducting properties and exhibit less quasiparticle broadening.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2021

Effect of Pd alloying on structural, electronic and magnetic properties of L1 0 Fe–Ni

We present a systematic study of the effect of Pd-alloying on phase stability, electronic structure, and elastic properties in L1 0 Fe–Ni using density-functional theory. Being from the same group of the periodic table, Pd is the best candidate for chemical alloying. The Fe–Ni/Fe–Pd/Ni–Pd bond-length increases with increasing Pd-concentration, which weakens the hybridization between low lying energy states below Fermi-level. The reduced hybridization decreases the relative thermodynamic stability of L1 0 Fe(Ni 1–x Pd x ) until x = 0.75. Beyond this concentration, the relative stability gets enhanced, which is attributed to a unique change in the lattice distortion (c/a). The elastic properties show a non-monotonous behavior as a function of x, which is again due to a specific change-over in the uniaxial strain. We found that Pd alloying increases the local Fe moment and structural anisotropy of L1 0 FeNi, which are important for applications such as microwave absorption, refrigeration systems, recording devices, imaging and sensors. Here, we believe that the present study for the chemical alloying effect can provide critical insights toward the understanding of electronic-structure and elastic behavior of other technologically important materials.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Data-Driven Analysis of Multipactor Dynamics via Dynamic Mode Decomposition

Multipactor effect is a performance-limiting kinetic plasma effect that can occur in high-power microwave and radio frequency (RF) devices. Multipactor effect is of special concern in vacuum or near-vacuum conditions such as those in particle accelerators and spaceborne devices. In this work, we present a data-driven reduced-order model (ROM) based on dynamic mode decomposition (DMD) for modeling of multipactor effects. We study multipactor effects and the resulting nonlinear harmonic generation by processing high-fidelity data generated from electromagnetic particle-in-cell (EMPIC) simulations using the DMD algorithm. We also investigate time-delay embedding extensions of DMD with improved generalizability and accuracy for modeling the electron plasma current density behavior. Here, the results show that DMD provides valuable insights into multipactor phenomena by extracting relevant modal spatiotemporal patterns and frequencies. In addition, DMD offers the potential to time extrapolate EMPIC simulations at a minimal cost, thereby reducing overall simulation time.

43 PARTICLE ACCELERATORS↗
DOE OSTI2021

Mitigating photorefractive effect in thin-film lithium niobate microring resonators

Thin-film lithium niobate is an attractive integrated photonics platform due to its low optical loss and favorable optical nonlinear and electro-optic properties. However, in applications such as second harmonic generation, frequency comb generation, and microwave-to-optics conversion, the device performance is strongly impeded by the photorefractive effect inherent in thin-film lithium niobate. In this paper, we show that the dielectric cladding on a lithium niobate microring resonator has a significant influence on the photorefractive effect. By removing the dielectric cladding layer, the photorefractive effect in lithium niobate ring resonators can be effectively mitigated. Our work presents a reliable approach to control the photorefractive effect on thin-film lithium niobate and will further advance the performance of integrated classical and quantum photonic devices based on thin-film lithium niobate.

42 ENGINEERING↗
DOE OSTI2025

SRF-Based Quantum Transduction for Quantum Computing and Sensing

The next groundbreaking frontier in Quantum Information Science (QIS) is the development of low-noise interconnections over fiber optics between superconducting radio-frequency (SRF) quantum devices. High-efficiency microwave-optical transduction serves as a pivotal enabler for distributed quantum computing and sensor networks. This presentation will provide a comprehensive overview of quantum transduction achieved by coupling SRF cavities to electro-optic optical resonators, enabling efficient conversion between microwave and optical photons. This research, supported by the DOE Early Career Research Program, advances technologies for quantum computing and sensing, and complements the mission of the Superconducting Quantum Materials and Systems (SQMS) Center at Fermilab.

Zorzetti, Silvia [Fermilab] (ORCID:000000023208338↗
DOE OSTI2024

Development of an MKID frequency-to-pixel LED mapper for SPT-3G+

SPT-3G+ is the next-generation camera for the South Pole Telescope (SPT). SPT is designed to measure the cosmic microwave background (CMB) and the mm/sub-mm sky. The planned focal plane consists of 34,000 microwave kinetic inductance detectors (MKIDs), divided among three observing bands centered at 220, 285, and 345 GHz. Each readout line is designed to measure 800 MKIDs over a 500 MHz bandwidth, which places stringent constraints on the accuracy of the frequency placement required to limit resonator collisions that reduce the overall detector yield. To meet this constraint, we are developing a two-step process that first optically maps the resonance to a physical pixel location, and then next trims the interdigitated capacitor (IDC) to adjust the resonator frequency. We present a cryogenic LED apparatus operable at 300 mK for the optical illumination of SPT-3G+ detector arrays. We demonstrate integration of the LED controls with the GHz readout electronics (RF-ICE) to take data on an array of prototype SPT-3G+ detectors. We show that this technique is useful for characterizing defects in the resonator frequency across the detector array and will allow for improvements in the detector yield.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2020

Microwave Microscopy and Its Applications

Understanding the nanoscale electrodynamic properties of a material at microwave frequencies is of great interest for materials science, condensed matter physics, device engineering, and biology. With specialized probes, sensitive detection electronics, and improved scanning platforms, microwave microscopy has become an important tool for cutting-edge materials research in the past decade. In this article, we review the basic components and data interpretation of microwave imaging and its broad range of applications. In addition to the general-purpose mapping of permittivity and conductivity, microwave microscopy is now exploited to perform quantitative measurements on semiconductor devices, photosensitive materials, ferroelectric domains and domain walls, and acoustic-wave systems. Implementation of the technique in low-temperature and high-magnetic-field chambers has also led to major discoveries in quantum materials with strong correlation and topological order. We conclude the review with an outlook of the ultimate resolution, operation frequency, and future industrial and academic applications of near-field microwave microscopy.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

Evidence of decoupling of surface and bulk states in Dirac semimetal Cd 3 As 2

Abstract Dirac semimetals have attracted a great deal of current interests due to their potential applications in topological quantum computing, low-energy electronic devices, and single photon detection in the microwave frequency range. Herein are results from analyzing the low magnetic ( B ) field weak-antilocalization behaviors in a Dirac semimetal Cd 3 As 2 thin flake device. At high temperatures, the phase coherence length l ϕ first increases with decreasing temperature ( T ) and follows a power law dependence of l ϕ ∝ T −0.4 . Below ∼3 K, l ϕ tends to saturate to a value of ∼180 nm. Another fitting parameter α , which is associated with independent transport channels, displays a logarithmic temperature dependence for T > 3 K, but also tends to saturate below ∼3 K. The saturation value, ∼1.45, is very close to 1.5, indicating three independent electron transport channels, which we interpret as due to decoupling of both the top and bottom surfaces as well as the bulk. This result, to our knowledge, provides first evidence that the surfaces and bulk states can become decoupled in electronic transport in Dirac semimetal Cd 3 As 2 .

77 NANOSCIENCE AND NANOTECHNOLOGY↗