Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “material modeling”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Inelastic deformation of diamond single crystals shock compressed to multimegabar stresses: Wave profile calculations

As the archetypal strong solid, the response of diamond shock compressed to multimegabar stresses is important for fundamental science and for numerical simulations of wave profiles for applications in high energy density physics experiments. Previous experiments and analysis have shown that the commonly used hydrodynamic assumption is invalid for diamond shock compressed to stresses below melt and an elastic–inelastic description is needed. Here, we present a phenomenological material model for calculating wave profiles in shock compressed diamond single crystals that incorporates this description. Also, to support the modeling effort, we carried out wave profile measurements on shock compressed diamond single crystals at the Sandia Z facility to augment previous measurements. Wave profiles for [100] and [111] diamond calculated using the material model provide a good match to the elastic–inelastic response (observed two-wave structure) measured at ∼325 and ∼360 GPa. Furthermore, the calculated peak stresses for single (overdriven) waves provide a good match to the measured Hugoniot states for stresses reaching ∼700 GPa, which is near melting conditions. The present results show that the diamond single crystal response at multimegabar shock stresses is characteristic of a brittle solid—pressure-dependent strength and strength loss due to inelastic deformation.

Deformation↗
DOE OSTI2025

Report on the "Symposium on Advancements in Simulating Neutron Scattering Instruments and Experiments"

An international group of researchers gathered for the “Symposium on Advancements in Simulating Neutron Scattering Instruments and Experiments” at Oak Ridge National Laboratory (ORNL) on October 29- 30, 2024. The symposium highlighted state-of-the-art advancements in neutron scattering instrument simulations and the development of digital twins for scattering instruments. This document summarizes the recurring themes from the 19 talks and discussions. A key focus was on the role of neutronics simulations in the design, analysis, and performance optimization of neutron instruments. Presentations featured the most widely used software packages, such as McStas, McVine, Vitess, and MCNP. Another major theme addressed the analysis and interpretation of experimental neutron data, where materials models and simulations play a critical role. Talks on relevant software tools, including NCrystal, OCLimax, and Paradyse, were delivered by their respective developers. During the symposium, both talks and breakout sessions explored strategies to enhance the interplay between neutronics simulations and materials models. A key question emerged: How can we develop a RealTime Explainable Digital Twin of a neutron scattering experiment? Discussions include the idea that the Digital Twin concept has implications for instrument control and testing. Through this symposium, we gained valuable insights into the challenges and requirements for developing a Real-Time Explainable Digital Twin of a neutron scattering experiment. The discussions and presentations paved the way for future innovations in this rapidly advancing field.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2025

Two-Dimensional Ferroelectric Altermagnets: From Model to Material Realization

Multiferroic altermagnets offer new opportunities for magnetoelectric coupling and electrically tunable spintronics. However, due to intrinsic symmetry conflicts between altermagnetism and ferroelectricity, achieving their coexistence, known as ferroelectric altermagnets (FEAM), remains an outstanding challenge, especially in two-dimensional (2D) systems. Here, we propose a universal, symmetry-based design principle for 2D FEAM, supported by tight-binding models and first-principles calculations. We show that lattice distortions can break spin equivalence and introduce the necessary rotation-related symmetry, enabling altermagnetism with electrically reversible spin splitting. Guided by this framework, we identify a family of 2D vanadium oxyhalides and sulfide halides as promising FEAM candidates. In these compounds, pseudo Jahn-Teller distortions and Peierls-like dimerization cooperatively establish the required symmetry conditions. Here, we further propose the magneto-optical Kerr effect as an experimental probe to confirm FEAM and its electric spin reversal. Furthermore, our findings provide a practical framework for 2D FEAM and advancing electrically controlled spintronic devices.

2D materials↗
DOE OSTI2026

Deposition Height Prediction in Directed Energy Deposition

Using 316L stainless steel as a model material, reduced-order models are developed to predict capture efficiency, deposition height, and site-specific hardness in directed energy deposition. Capture efficiency is predicted over a 15 to 55 pct range using a dimensionless number derived from processing conditions and thermophysical properties. Deposition height is predicted over a 0.3 to 1.3 mm range without in situ sensing or prior training data, using two models based on the same mass and energy-balance principles. Predictions are compared with machine learning approaches. A quantitative relationship links deposition height, primary dendrite arm spacing (PDAS), and hardness: heights of 0.3 to 1.1 mm correspond to PDAS values of 2.7 to 5.1 µm and Vickers hardness (HV) of 160 to 219. Thinner layers cool more rapidly, producing finer microstructures and higher hardness. Samples fabricated with in situ variations in deposition height exhibited up to 55 HV differences between thick and thin regions, demonstrating that local control of deposition height enables predictive, site-specific hardness within a single build. These results establish deposition height prediction as a pathway for a priori process design and property control in directed energy deposition for 316L stainless steel.

Kunkel, William [Univ. of Wisconsin, Madison, WI (↗
DOE OSTI2026

Fracture Analysis of Cohesive Zone Models for Modeling Residual Stress Induced Delamination in Composite Structures

A fracture study of coupon-scale composite cylinders with embedded defects was conducted with an objective to assess and validate a modeling approach using two available cohesive material models. The study included experimental and simulation evaluations of initiation of crack growth and progression. Interrupted thermal experiments used acoustic emissions monitoring to identify the onset of crack progression during each cooling interval and ultrasonic scanning provided images of defect growth. Verification, validation, and uncertainty quantification (VVUQ) processes were performed in the assessment of the simulation predicted temperature at which crack propagation begins (quantity of interest). The Sobol sensitivity analysis identified the hoop direction elastic modulus in the carbon fiber reinforced polymer (CFRP) plies as the most influential parameter for simulations using both cohesive models, accounting for at least 70% of the variation in the temperature at crack propagation. The UQ temperature range for the Tvergaard-Hutchinson model was higher (more conservative) than the experimental acoustic measurement indicators of crack progression, while the temperature range for the Thouless-Parmigiani model enveloped the experimental data points for the primary defect size of 0.75 x 1 in. The simulations could not capture the stable crack growth indicated in the experiments. This is likely due to the models’ inability to represent anisotropic fracture toughness attributed to the structure of the orthotropic fiber weave in a woven composite laminate.

42 ENGINEERING↗
DOE OSTI2025

Effects cascade debris and helium bubbles on the strength of aged plutonium

The radioactive decay of aging Pu is dominated by α-decay. This persistent α-decay produces crystalline defects in the form of dislocation loops and helium bubbles that evolve with time. Comparable defects are produced in other metallic alloys when subject to neutron irradiation, and these defects are known to modify the plastic deformation of irradiated materials. Models have been developed for these irradiated materials and validated against experimental confirmations of yield strength and the concomitant microstructural evolution. In this paper, we deploy those previously developed models and apply their mechanics to plutonium aging.

Chemical elements↗
DOE OSTI2026

The effectiveness of D 2 pellet and gas injection in reducing intra-ELM tungsten erosion and heat flux in the DIII-D small angle slot divertor

Edge localized modes (ELMs) in H-mode plasmas can melt and erode plasma-facing components (PFCs) and lead to impurities in the core, reducing confinement. This study analyzes the use of D 2 pellet and gas injection for ELM mitigation on the DIII-D tokamak during the 2022 Small Angle Slot V-shaped Tungsten (W) (SAS-VW) divertor campaign, reducing W erosion and heat flux during ELMs. D α (656 nm) and WI (400.9 nm) filterscopes and Langmuir probes provide photon emission and electron density/temperature to estimate W atom erosion using the S/XB method, while surface eroding thermocouples measured ELM peak heat flux at the outer strike point (OSP). Thomson Scattering measurements of pedestal T e and n e provided input to predict W divertor erosion and heat flux during ELMs via the Free-Streaming plus Recycling Model (FSRM). While a greater D 2 mass injection rate decreased the ELM peak heat flux, the impact on W erosion was not monotonic. The average ‘large’ intra-ELM W erosion was lower for plasma shots with D 2 mass injection compared to the plasma shots without any D 2 mass injection in the SAS-VW divertor. However, plasma shots did not see significant changes in ‘large’ intra-ELM W divertor erosion as the D 2 mass injection rate increased. On average, the FSRM overestimated SAS-VW experimental intra-ELM W erosion by a factor of 6.9, but the overestimation is reduced to a factor of 3.6 with the implication of C deposition effects. Generally, experimentally measured and predicted quantities were worse for plasma shots with a lower D 2 mass injection rate and corresponding higher plasma carbon (C) impurity percentage (f C ). The discrepancies are postulated to be due to C/W material mixing, for which a simple analytic mixed-material model is presented. These results highlight the importance of incorporating and improving the robustness of a mixed-material layer model in the analysis of PFC erosion on present and future tokamak devices.

Carbon (C)↗
DOE OSTI2025

Accelerated Fuel Qualification of Fast Modular Reactor Fuel in a Thermal Reactor: Modeling and Simulation Paired with Irradiation Testing

The accelerated fuel qualification (AFQ) methodology is applied by simulating accelerated fuel tests of the General Atomics Electromagnetic Systems’ fuel system for its 44-MW(electric) gas-cooled, fast-spectrum fast modular reactor (FMR). This fuel is comprised of UO 2 pellets in SiGA® cladding, a silicon carbide ceramic matrix composite. Fast reactors, like the FMR, offer many benefits, including high fuel utilization and flexibility, but may require a lengthy material design process if tests are performed using fast neutron irradiation alone. A thermal neutron irradiation can instead be used to rapidly test how well key components of the current material models extend to high burnup. Thermal neutrons produce a different radial power distribution within the pin than fast neutrons. However, the temperature and burnup values for the two neutron types are comparable, and the differences between the simulated fuel responses are relatively small, demonstrating the weak sensitivity of the physics-based fuel model calculations on the neutron type and the irradiation rate. Furthermore, the deformation of the SiGA cladding saturates after about 1 displacement per atom for both neutron spectra. In an accelerated fuel test, the irradiation time required to reach the target fuel burnup can be reduced by a factor of 3 by using a small rodlet with a 45% smaller pellet diameter while maintaining the same linear power. Therefore, the time for data collection up to high burnup can be significantly reduced while maintaining the same temperature profile, which largely determines the material response. Tests of fuel rodlets of standard and compact size will be carried out in the Idaho National Laboratory’s Advanced Test Reactor (ATR), including full size and compact rodlets with varying gap sizes. By applying physics-based mechanistic modeling and simulation in accordance with the AFQ methodology, this type of compact rodlet testing in a thermal test reactor captures the necessary phenomena to test fuel material models up to high burnup and to simulate the expected impact of fast neutron radiation on the fuel in FMR operations. Finally, this approach to testing fast reactor fuels in existing thermal test reactors, paired with advanced physics-based mechanistic modeling and simulation, is expected to be applicable to a range of advanced fuels and will decrease the overall fuel qualification timeframe from decades to years.

Advanced test reactor (ATR)↗
DOE OSTI2025

Development, validation, and verification of multi-pass thermo-mechanical welding simulations using the open-source MOOSE framework: NeT TG4 benchmark weldment

This study develops and validates a sequentially coupled thermo-mechanical welding simulation for the three-pass 316L stainless steel NeT TG4 benchmark weldment using the open-source Multiphysics Object-Oriented Simulation Environment (MOOSE) and the Nuclear Engineering Material model Library (NEML). A diffused ellipsoidal heat source was calibrated against thermocouple data and weld macrographs to accurately model the fusion zone geometry and transient thermal fields. Material hardening is represented using the Lemaitre-Chaboche mixed isotropic-kinematic hardening model, while four annealing models - no annealing, single-stage at 1050 °C and 1300 °C, and two-stage at 800 °C/1300 °C - were implemented to assess the impact of annealing models on the accuracy of the predicted welding-induced plasticity, distortions, and residual stresses. The predictions were validated against experimental measurements and benchmarked against results from commercial software, demonstrating that thermo-mechanical MOOSE welding simulations achieve comparable accuracy with enhanced computational efficiency. This work highlights the potential of using open-source finite element frameworks like MOOSE for advanced manufacturing simulations.

Ji, Wendy [Australian Nuclear Science and Technolo↗
DOE OSTI2024

Enabling Parallel Performance and Portability of Solid Mechanics Simulations Across CPU and GPU Architectures

Efficiently simulating solid mechanics is vital across various engineering applications. As constitutive models grow more complex and simulations scale up in size, harnessing the capabilities of modern computer architectures has become essential for achieving timely results. This paper presents advancements in running parallel simulations of solid mechanics on multi-core CPUs and GPUs using a single-code implementation. This portability is made possible by the C++ matrix and array (MATAR) library, which interfaces with the C++ Kokkos library, enabling the selection of fine-grained parallelism backends (e.g., CUDA, HIP, OpenMP, pthreads, etc.) at compile time. MATAR simplifies the transition from Fortran to C++ and Kokkos, making it easier to modernize legacy solid mechanics codes. We applied this approach to modernize a suite of constitutive models and to demonstrate substantial performance improvements across different computer architectures. This paper includes comparative performance studies using multi-core CPUs along with AMD and NVIDIA GPUs. Results are presented using a hypoelastic–plastic model, a crystal plasticity model, and the viscoplastic self-consistent generalized material model (VPSC-GMM). The results underscore the potential of using the MATAR library and modern computer architectures to accelerate solid mechanics simulations.

Morgan, Nathaniel (ORCID:0000000276118449)↗
DOE OSTI2024

A Theoretical Analysis on the Dynamic Behavior and Electromechanical Response of PZT

Piezoelectric materials are used as a power source in stockpile components for safety and reliability assurances. The objective of this project is to gain insights into the fundamental pressure-induced behavior and electromechanical response of lead zirconate titanate (PZT). Specifically, to establish the basis for an accurate, physics-based material model for robust model-based design to rapidly optimize PZT-based materials and components for performance studies. Established ab-initio methods are used to interrogate and understand the dynamic behavior of PZT as a function of composition (50/50, 65/35, 80/20, 95/5) and dopants (La, Nb) to overcome the costly and time-consuming experimental methodologies. New cold curves for pure and doped single-crystal PZT are obtained as the reference equation-of-state (EOS). A negligible change in the pressure responses was observed for the systems and strains studied. Dielectric and piezoelectric responses of pure and doped single-crystal PZT were also calculated as a function of pressure. For undoped PZT, there is a clear and orderly pressure and composition dependence. For doped PZT, there is a significant increase in the responses, but the behavior is very disordered and inconclusive.

36 MATERIALS SCIENCE↗