Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “longitudinal comparison”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 73 records · Page 4
All sourcesNASA NTRSDOE OSTI
NASA NTRS1981

Space Shuttle entry aerodynamic comparisons of flight 1 with preflight predictions

Results of comparisons of predictions of aerodynamic performance, longitudinal trim, and reaction control jet interaction with data from the initial Shuttle flight are presented. The Shuttle's control surfaces are described, and it is noted that the flight plan contained no provisions for maneuvering capability tests. Wind tunnel testing totaling 35,000 hr were used to replace graduated flight testing, and calculations were made to allow for nonsimulated structural deformation, flowfield parameters, and profile drag. The goal was to desensitize the flight control system with respect to the aerodynamics by adding variations to the predictions. Lift/drag agreed well above Mach 1, while lower drag was encountered below Mach 1. Trim characteristics were predicted accurately between Mach 2-10, and less than satisfactorily outside that range. Discrepancies were also observed for jet interaction effects for the aft yaw jets at Mach numbers greater than 10.

Young, J. C.↗
NASA NTRS1985

Hypersonic characteristics of an advanced aerospace plane

A series of hypersonic wind-tunnel tests have been conducted in the NASA Langley Hypersonic Facilities Complex to obtain the static longitudinal and lateral-directional aerodynamic characteristics of an advanced aerospace plane. Data were obtained at 0 to 20 deg angles of attack and -3 to 3 deg angles of sideslip at Mach numbers of 6 and 10 in air and 20 in helium. Results show that stable trim capability exists at angles of attack near maximum lift-drag ratio (L/D). Both performance and stability exhibited some Mach number dependency. The vehicle was longitudinally unstable at low angles of attack but stable at angles of attack near and above maximum L/D. It was directionally unstable with positive dihedral effect. The rudder showed an inability to provide lateral-directional control, and removing the vertical tail resulted in increased directional instability. Analytical predictions of the static longitudinal aerodynamic coefficients gave relatively good comparisons with the experimental data.

Mccandless, R. S.↗
NASA NTRS1988

A study of helicopter stability and control including blade dynamics

A linearized model of rotorcraft dynamics has been developed through the use of symbolic automatic equation generating techniques. The dynamic model has been formulated in a unique way such that it can be used to analyze a variety of rotor/body coupling problems including a rotor mounted on a flexible shaft with a number of modes as well as free-flight stability and control characteristics. Direct comparison of the time response to longitudinal, lateral and directional control inputs at various trim conditions shows that the linear model yields good to very good correlation with flight test. In particular it is shown that a dynamic inflow model is essential to obtain good time response correlation, especially for the hover trim condition. It also is shown that the main rotor wake interaction with the tail rotor and fixed tail surfaces is a significant contributor to the response at translational flight trim conditions. A relatively simple model for the downwash and sidewash at the tail surfaces based on flat vortex wake theory is shown to produce good agreement. Then, the influence of rotor flap and lag dynamics on automatic control systems feedback gain limitations is investigated with the model. It is shown that the blade dynamics, especially lagging dynamics, can severly limit the useable values of the feedback gain for simple feedback control and that multivariable optimal control theory is a powerful tool to design high gain augmentation control system. The frequency-shaped optimal control design can offer much better flight dynamic characteristics and a stable margin for the feedback system without need to model the lagging dynamics.

Zhao, Xin↗
NASA NTRS2006

Free Body Dynamics of a Spinning Cylinder With Planar Restraint (a.k.a. Barrel of Fun)

The dynamic motion of a cylinder on a floor or hard surface is both entertaining and instructive. With maintenance torques, motion can be sustained and controlled as illustrated in a video clip that can be viewed in the PDF file of this document. The analysis of such a cylinder with and without end caps is burned on rotation about its center of mass and restrained by a plane normal to the axis passing through its center of mass at an angle alpha. For small values of alpha, the governing equations are simplified, and for symmetric bodies, stability requires rotation greater than [2 square root of(JWL*)]/J(sub X), where J is the transverse mass moment of inertia, W is the weight of the cylinder, L* is the cylinder length from the base to the center of mass, and JX is the mass moment of inertia about the longitudinal axis OX of the barrel. Comparisons to data are made and some applications are discussed.

Moraru, Laurentiu↗
NASA NTRS2011

ARES I Aerodynamic Testing at the NASA Langley Unitary Plan Wind Tunnel

Small-scale force and moment and pressure models based on the outer mold lines of the Ares I design analysis cycle crew launch vehicle were tested in the NASA Langley Research Center Unitary Plan Wind Tunnel from May 2006 to September 2009. The test objectives were to establish supersonic ascent aerodynamic databases and to obtain force and moment, surface pressure, and longitudinal line-load distributions for comparison to computational predictions. Test data were obtained at low through high supersonic Mach numbers for ranges of the Reynolds number, angle of attack, and roll angle. This paper focuses on (1) the sensitivity of the supersonic aerodynamic characteristics to selected protuberances, outer mold line changes, and wind tunnel boundary layer transition techniques, (2) comparisons of experimental data to computational predictions, and (3) data reproducibility. The experimental data obtained in the Unitary Plan Wind Tunnel captured the effects of evolutionary changes to the Ares I crew launch vehicle, exhibited good agreement with predictions, and displayed satisfactory within-test and tunnel-to-tunnel data reproducibility.

Erickson, Gary E.↗
NASA NTRS2016

Longitudinal Aerodynamic Modeling of the Adaptive Compliant Trailing Edge Flaps on a GIII Airplane and Comparisons to Flight Data

A pair of compliant trailing edge flaps was flown on a modified GIII airplane. Prior to flight test, multiple analysis tools of various levels of complexity were used to predict the aerodynamic effects of the flaps. Vortex lattice, full potential flow, and full Navier-Stokes aerodynamic analysis software programs were used for prediction, in addition to another program that used empirical data. After the flight-test series, lift and pitching moment coefficient increments due to the flaps were estimated from flight data and compared to the results of the predictive tools. The predicted lift increments matched flight data well for all predictive tools for small flap deflections. All tools over-predicted lift increments for large flap deflections. The potential flow and Navier-Stokes programs predicted pitching moment coefficient increments better than the other tools.

aerodynamics↗
NASA NTRS1973

Hypersonic aerodynamic characteristics of an all-body research aircraft configuration

An experimental investigation was conducted at Mach 6 to determine the hypersonic aerodynamic characteristics of an all-body, delta-planform, hypersonic research aircraft (HYFAC configuration). The aerodynamic characteristics were obtained at Reynolds numbers based on model length of 2.84 million and 10.5 million and over an angle-of-attack range from minus 4 deg to 20 deg. The experimental results show that the HYFAC configuration is longitudinally stable and can be trimmed over the range of test conditions. The configuration had a small degree of directional stability over the angle-of-attack range and positive effective dihedral at angles of attack greater than 2 deg. Addition of canards caused a decrease in longitudinal stability and an increase in directional stability. Oil-flow studies revealed extensive areas of separated and vortex flow on the fuselage lee surface. A limited comparison of wind-tunnel data with several hypersonic approximations indicated that, except for the directional stability, the tangent-cone method gave adequate agreement at control settings between 5 deg and minus 5 deg and positive lift coefficient. A limited comparison indicated that the HYFAC configuration had greater longitudinal stability than an elliptical-cross-section configuration, but a lower maximum lift-drag ratio.

Clark, L. E.↗
NASA NTRS2013

Longitudinally Jointed Edge-Wise Compression HoneyComb Composite Sandwich Coupon Testing And Fe Analysis: Three Methods of Strain Measurement, And Comparison

Three distinct strain measurement methods (i.e., foil resistance strain gages, fiber optic strain sensors, and a three-dimensional digital image photogrammetry that gives full field strain and displacement measurements) were implemented to measure strains on the back and front surfaces of a longitudinally jointed curved test article subjected to edge-wise compression testing, at NASA Goddard Space Flight Center, according to ASTM C364. The pre-test finite element analysis (FEA) was conducted to assess ultimate failure load and predict strain distribution pattern throughout the test coupon. The predicted strain pattern contours were then utilized as guidelines for installing the strain measurement instrumentations. The foil resistance strain gages and fiber optic strain sensors were bonded on the specimen at locations with nearly the same analytically predicted strain values, and as close as possible to each other, so that, comparisons between the measured strains by strain gages and fiber optic sensors, as well as the three-dimensional digital image photogrammetric system are relevant. The test article was loaded to failure (at ~167 kN), at the compressive strain value of ~10,000 micro epsilon. As a part of this study, the validity of the measured strains by fiber optic sensors is examined against the foil resistance strain gages and the three-dimensional digital image photogrammetric data, and comprehensive comparisons are made with FEA predictions.

Farrokh, Babak↗
NASA NTRS1982

Effects of vortex breakdown on longitudinal and lateral-directional aerodynamics of slender wings by the suction analogy

A semi-empirical method based on the suction analogy is developed to predict longitudinal aerodynamics and lateral-directional characteristics of slender wings at high angles of attack, including effects of vortex breakdown. The latter is based on a correlation parameter derived from the predicted leading-edge suction distribution in the attached flow. Empirical formulas, derived from a least-square analysis of data, for the vortex-breakdown angle of attack at the trailing edge, the progression rate of breakdown points and the vortex lift recovery factor in the breakdown region are given. Comparison of predicted results with data in longitudinal aerodynamics and lateral-directional characteristics for wings exhibiting strong vortex flow shows that the present method is reasonably accurate. Explanation for peculiar lateral-directional characteristics is given.

Lan, C. E.↗
NASA NTRS1982

Aerodynamic comparisons of STS-1 Space Shuttle entry vehicle

A conventional flight-test program, which slowly and cautiously approaches more severe flight conditions, was not possible with the Orbiter. On the first flight, the Orbiter entered the atmosphere at Mach 28 and decelerated through the Mach range. (The subsonic portion of flight was also flown by another orbiter vehicle during the Approach and Landing Test Program.) Certification for the first flight was achieved by an extensive wind-tunnel test and analysis program and by restricting the flight maneuvers severely. The initial flights of the orbiter were heavily instrumented for the purpose of obtaining accurate aerodynamic data. Even without maneuvers to excite the system, the first flight provided comparisons between flight and wind-tunnel-derived predicted data in the areas of aerodynamic performance, longitudinal trim, and reaction-control jet interaction. The aerodynamic performance comparisons are presented.

Young, J. C.↗
NASA NTRS2017

Cardiovascular Disease Risk in NASA Astronauts Across the Lifespan: Historical Cohort Studies

Acute effects of spaceflight on the cardiovascular system have been studied extensively, but the combined chronic effects of spaceflight and aging are not well understood. Preparation for and participation in space flight activities are potentially associated with cardiovascular disease risk factors (e.g., altered dietary and exercise habits, physical and emotional stress, circadian shifts, radiation). Further, astronauts who travel into space multiple times may be at an increased risk across their lifespan. However, comparing the risk of cardiovascular disease in astronauts to other large cohorts is difficult. For example, comparisons between astronauts and large national cohorts, such as the National Health and Nutrition Examination Survey and the National Health Information Survey, are hampered by significant differences in health status between astronauts and the general population, and most of these national studies fail to provide longitudinal data on population health. To address those limitations, NASA's Longitudinal Study of Astronaut Health previously sought to compare the astronauts to a cohort of civil servants employed at the Johnson Space Center. However, differences between the astronauts and civil servants at the beginning of the study, as well as differential follow up, limited the ability to interpret the results. To resolve some of these limitations, two unique cohorts of healthy workers, U.S. Air Force aviators and Cooper Center Longitudinal Study participants, have been identified as potential comparison populations for the astronaut corps. The Air Force cohort was chosen due to similarities in health at selection, screening, and some occupational exposures that Air Force aviators endure, many of which mirror that of the astronaut corps. The Cooper Clinic cohort, a generally healthy prevention cohort, was chosen for the vast array of clinical cardiovascular measures collected in a longitudinal manner complementary to those collected on astronauts, for a large number of subjects since 1971. The purpose of this study is to understand the incidence of cardiovascular disease outcomes and risk factors in the astronaut corps and determine whether the rates of disease are different than these two cohorts. The research questions are: 1. Are there differences in the incidence of CVD outcomes (MI, revascularization, and stroke) between each cohort and the NASA Astronaut cohort? 2. Are there differences in the incidence of CVD risks (hypertension, hyperlipidemia, arrhythmias, and diabetes) between each cohort and the NASA Astronaut cohort? 3. Are there differences between each cohort and the NASA Astronaut cohort in how CVD risk factors (e.g., lipids, behaviors) change across time? Collectively, results from these studies will enhance our understanding of how cardiovascular disease outcomes and risk factors change across time in astronauts compared to other longitudinally-studied healthy cohorts and determine if there are interactions between or additive effects of the occupational health effects of spaceflight exposure and normal aging.

Charvat, Jacqueline M.↗
DOE OSTI2021

Supporting data for climatic clustering and longitudinal analysis with impacts on food, bioenergy, and pandemics

This data supports the conclusions found in climatic clustering and longitudinal analysis with impacts on food, bioenergy, and pandemics. Included here are (i) the binarized geolocation vectors used for exhaustive vector comparisons, (ii) the resulting climatic networks, (iii) the results of applying Markov clustering to the climatic networks, and (iv) the results of applying Correlation-of-Correlations (cor-cor) to the climatic networks. The set of binarized geolocation vectors that are used as inputs for the Combinatorial Metrics library (CoMet) are of the form comet-UUUUUxVVVVV-XXXX-YYYY.shuffled.tped where UUUUU is the number of vectors, VVVVV is the length of each vector, XXXX is the starting year, and YYYY is the ending year. Each line corresponds to a geolocation vector of binary elements A (i.e., 0) and T (i.e., 1). The set of climatic networks that are used for downstream network analysis are of the form network-U-way-XXXX-YYYY.parsed.txt where U is the order of the comparison (2-way or 3-way), XXXX is the starting year, and YYYY is the ending year. Each line corresponds to an edge linking two geolocations (defined by latitude and longitude) with its corresponding edge weight (i.e., DUO score). The set of cluster results are of the form clusters-U-way-XXXX-YYYY-thresh-VVVV-inflation-WWW.clustered.txt where U is the order of the comparison (2-way or 3-way), XXXX is the starting year, YYYY is the ending year, VVVV is the similarity threshold, and WWW is the Markov clustering inflation rate. Each line corresponds to a single cluster and is composed of a number of corresponding geolocations (defined by latitude and longitude). The set of cor-cor results are of the form corcor-U-way-XXXX-YYYY.cumulative.txt where U is the order of the comparison (2-way or 3-way), XXXX is the starting year, and YYYY is the ending year. Each line corresponds to a single geolocation with it's corresponding cor-cor value.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1979

Interaction between a normal shock wave and a turbulent boundary layer at high transonic speeds. Part 1: Pressure distribution

Analytical solutions are derived which incorporate additional physical effects as higher order terms for the case when the sonic line is very close to the wall. The functional form used for the undisturbed velocity profile is described to indicate how various parameters will be calculated for later comparison with experiment. The basic solutions for the pressure distribution are derived. Corrections are added for flow along a wall having longitudinal curvature and for flow in a circular pipe, and comparisons with available experimental data are shown.

Messiter, A. F.↗
NASA NTRS1986

Interpretation of the prominence differential emissions measure for 3 geometries

Researchers have used prominence extreme ultraviolet line intensities observed from Skylab to derive the differential emission measure Q(T) in the prominence-corona (PC) interface from 3 x 10,000 to 3 times 1 million K, including the effects of Lyman Continuum absorption. Using lines both shortward and longward of the Lyman limit, researchers have estimated the importance of absorption as function of temperature. The magnitude of the absorption, as well as its rate of increase as a function of temperature, place limits on the thread scales and the character of the interfilar medium. Researchers have calculated models based on three assumed geometries: (1) threads with hot sheaths and cool cores; (2) isothermal threads; and (3) threads with longitudinal temperature gradients along the magnetic field. Comparison of the absorption computed from these models with the observed absorption in prominences shows that none of the geometries is totally satisfactory.

Schmahl, E. J.↗
NASA NTRS1979

Effects of relaxed static longitudinal stability on a single-stage-to-orbit vehicle design

The effects of relaxing longitudinal stability requirements on single stage to orbit space vehicles is studied. A comparison of the mass and performance characteristics of two vehicles, one designed for positive levels of longitudinal stability and the other designed with relaxed stability requirements in a computer aided design process is presented. Both vehicles, required to meet the same mission characteristics are described. Wind tunnel tests, conducted over a Mach number range from 0.3 to 4.63 to verify estimated aerodynamic characteristics, are discussed.

Freeman, D. C., Jr.↗