SEARCH · Engineering Papers
Results for “lignin fractionation”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Carbon fibers derived from environmentally benign, ethanol-fractionated corn-stover lignin
Corn stover-derived lignin, a sustainable and cheaper precursor, was ALPHA-fractionated and dry-spun using ethanol solvent to produce carbon fibers with improved properties via faster processing.
Upconversion of non-recycled MSW paper fractions into biochar via slow pyrolysis and life cycle analysis: Pathways to net negative GHG emission
This study presents an integrated and sustainable approach to valorizing non-recycled municipal solid waste (MSW), a heterogeneous and underutilized waste stream destined for landfilling, by converting it into valuable biochar resources. Specifically, we investigated the upcycling of nonrecycled paper waste based on compositional analysis into four major fractions: high cellulose, high lignin, high contamination, and high ash content papers. These fractions were then homogenized and subjected to slow pyrolysis. The high cellulose fraction (36.1 %) was the most abundant, and contained 66.7 % cellulose, while the high lignin fraction showed the highest lignin (12.1 %) and carbon content (44 %), resulting in highest energy value of 17.4 MJ kg −1 . Biochar yields ranged from 25.6 % to 35.6 %, with the high ash fraction producing the highest yield and alkalinity (pH ≈ 11.2) due to its higher mineral content. Elemental analysis revealed enhanced carbon content up to 76.9 % and reduced oxygen and hydrogen, confirming effective carbonization. The high lignin-derived biochar showed the highest aromatic carbon content (82.8 %) and greater structural stability, while contaminated and ash-rich fractions exhibited dense, low-porosity surfaces due to the presence of contaminants and minerals. Spectroscopic analysis revealed degradation of carbohydrates, disappearance of cellulose peaks and formation of aromatic and mineral derived phases. The scaled life cycle process yielded a global warming potential (GWP) of 119.3 kg CO 2 -eq per ton of dry paper waste, offset by soil carbon sequestration of − 556.41 kg CO 2 -eq, resulting in a net impact of − 427.36 kg CO 2 -eq. This represents a net carbon removal exceeding by ~186 % the emissions associated with landfilling paper waste with electricity generation.
One-step lignocellulose depolymerization and saccharification to high sugar yield and less condensed isolated lignin
The cost of sugar production remains a key challenge in future lignocellulosic biorefineries. We demonstrate that ZnBr 2 , an inexpensive inorganic salt, provides nearly theoretical yields of glucose and xylose in one-step from poplar wood at 85 °C and short reaction times at molten salt hydrate (MSH) conditions without an acid. Catalytic depolymerization of the isolated MSH lignin, using a CoS 2 catalyst, yields 17% phenol-like monomers compared to only 1% produced from the acidified MSH lignin. Reductive catalytic fractionation of MSH lignin over Ru/C resulted in two times higher total monomer yield compared to the AMSH lignin. Both the lignin samples were characterized using 2D HSQC NMR and the thioacidolysis method. Thioacidolysis studies reveal 8.4% and 1.8% of β-O-4 linkages in MSH and acidified MSH lignin, respectively. Thermodynamic modeling and 13 C NMR spectroscopy indicate that the effectiveness of this catalyst arises from the strong interaction of the Lewis acidic zinc cation (Zn 2+ ) with the coordinated water molecules resulting in hydrolysis of the metal aquo complex and to the salt-driven increase in the H + activity coefficient. Techno-economic analysis demonstrates that despite being slower, the ZnBr 2 MSH media has cost advantages, compared to conventional hydrolysis and even to the LiBr and ZnBr 2 AMSH, due to the higher quality of lignin.
Multi-scale computational screening and mechanistic insights of cyclic amines as solvents for improved lignocellulosic biomass processing
A computational screening workflow for the efficient deconstruction of cellulose, lignin and hemicellulose fractions of lignocellulosic biomass using cyclic amines as solvents. Lignocellulosic biomass is a promising feedstock for production of affordable fuels and chemicals from renewable resources. Effective solubilization and subsequent deconstruction of its cellulose, hemicellulose, and lignin fractions is essential for the viability of future biorefineries. This study used quantum chemistry-based equilibrium thermodynamics methods to evaluate the potential of 650 cyclic amines to solubilize cellulose, hemicellulose, and lignin. The activity coefficients of solvent - biopolymer interactions were predicted using the COSMO-RS (COnductor-like Screening MOdel for Real Solvents) method and used to identify cyclic amines that can efficiently dissolve and extract selective fractions of biopolymers during biomass pretreatment. Among the 650 cyclic amines, 1-piperazineethanmaine was predicted to be an effective solvent for extracting all three polymers and was experimentally shown to achieve the highest lignin removal (97.1%). Non-covalent interaction, reduced density gradient and quantum chemical calculations were performed to elucidate the dissolution mechanism of lignin, cellulose and hemicellulose and gain further molecular level insights into the interactions between the cyclic amines and biomass polymers that promote efficient solubilization and extraction. These analyses indicated that 1-piperazineethanmaine and 1-methylimidazole make noncovalent van der Waals, electrostatic interactions and hydrogen bonding with lignin, leading to enhanced lignin removal, while the strong intramolecular hydrogen bonding interactions in cellulose and hemicellulose result in weaker solvent-biopolymer interactions. Overall, the computational approach provided an efficient method for identifying cyclic amines tailored for optimal biomass pretreatment and resulted in the identification of a potential new class of solvents for effective biomass pretreatment.
Identification and quantification of lignin monomers and oligomers from reductive catalytic fractionation of pine wood with GC × GC – FID/MS
Thorough lignin characterization is vital to understand the physicochemical properties of lignin and to evaluate lignocellulose biorefinery processes. In this study, an in-depth characterization of lignin oil, obtained from reductive catalytic fractionation (RCF) of pine wood, was performed with quantitative GC × GC – FID analysis and qualitative GC × GC – MS. By utilizing high-temperature resistant column sets in the GC × GC system and by applying a derivatization step, unambiguous detection of lignin monomers, dimers, and trimers is enabled. In addition to confirm the identity of eleven monomers, corresponding to 34 wt% of the RCF lignin oil, thirty-six dimers (16 wt%) and twenty-one trimers (7 wt%) were comprehensively identified by analysis of their mass spectra and quantified by a FID, encompassing the identity of an additional 23 wt% of the RCF lignin oil. The proposed structures reveal the interlinkages present in the dimeric and trimeric oligomers, containing β-5, β-1, β–β, 5–5, and a minor fraction of β-O-4 and 4-O-5 bonds. Furthermore, aliphatic end-units in the dimeric and trimeric molecules were identified, consisting of various substituents at the C4 position, that have been previously observed in the RCF-derived lignin monomers. To reduce complexity for analysis, the RCF oil was separated into six fractions, prior to analysis. The structural motifs (inter-unit linkages and end-units) that are found in the different fractions vary significantly, such that the lignin fractions extracted in more polar solvents contained higher molecular weight fragments and more hydroxyl containing structural motifs. Additionally, the identified structures of individual dimer and trimer molecules by GC × GC align well with and further complement the recent findings from 1 H– 13 C HSQC NMR spectroscopy, demonstrating complementarity between both 2D techniques to obtain a holistic view on both the molecular structures and the distribution of bonds and end-units in RCF oil. The combination of these two techniques provides a powerful tool for future RCF and other lignin depolymerization research.
Isolation, Characterization, and Depolymerization of L -Cysteine Substituted Eucalyptus Lignin
Lignin condensation reactions are hard to avoid or control during separation, which is a deterrent to lignin isolation and post-conversation, especially for the full utilization of lignocelluloses. Selective protection of β-aryl ether linkages in the isolation process is crucial to lignin valorization. Herein, a two-step acid/alkali separation method assisted with l-cysteine for eucalyptus lignin separation is developed, and the isolated L -cysteine lignins (LCLs) are comprehensively characterized by 2D NMR, 31 P NMR, thioacidolysis, etc. Compared to the two-step control treatment, a much higher β-O-4 content is preserved without reducing the separation efficiency assisted by L -cysteine, which is also significantly higher than alkali lignin and kraft lignin. The results of hydrogenolysis show that LCLs generate a much higher monomer yield than that of control sample. Structural analysis of LCLs suggests that lignin condensation reaction, to some extent, is suppressed by adding L -cysteine during the two-step acid/alkali separation. Further, mechanistic studies using dimeric model compound reveals that L -cysteine may be the α-carbon protective agent in the two-step separation. The role of L -cysteine in the two-step lignin isolation method provides novel insights to the selective fractionation of lignin from biomass, especially for the full valorization of lignocellulosic biomass.
Deep Eutectic Solvents for Efficient Fractionation of Lignocellulose to Produce Uncondensed Lignin and High-Quality Cellulose
Simultaneously inhibiting lignin condensation and cellulose degradation remains a major challenge for achieving holistic valorization of lignocellulose. Here, we developed a deep eutectic solvent (DES), composed of l-cysteine (Cys) and lactic acid (LA), to fractionate both uncondensed lignin and high-quality cellulose from eucalyptus wood by leveraging the unique properties of Cys, i.e., highly nucleophilic groups (–SH) and hydrogen bond acceptor/donor groups (–NH 2 and –COOH). The nucleophilic –SH in Cys effectively quenches the benzylic carbocations (C α + ions, formed at the benzylic sites of lignin) that lead to lignin condensation. This enables the high yield of uncondensed lignin (81%) with high retention of β–O–4 bonds (up to 90%). The separated uncondensed lignin is further depolymerized to prepare monophenols in a satisfactory 43% yield, equivalent to 73% of the theoretical yield. Moreover, the –NH 2 and –COOH groups in Cys form extensive hydrogen bonds with the hydroxyl groups in cellulose, thus decreasing the interaction energy of DES on cellulose. As a result, the cellulose achieves an astonishing 99% retention and maintains a high degree of polymerization of 1160. The obtained high-quality cellulose is further conversed into cellulose nanofibers for strong and transparent films. Furthermore, this study provides new insights into the efficient separation of uncondensed lignin and high-quality cellulose from lignocellulose by a novel DES system.
Effect of the Lignin Structure on the Physicochemical Properties of Lignin-Grafted-Poly(ε-caprolactone) and Its Application for Water/Oil Separation
Lignin-grafted poly(ε-caprolactone) copolymers (lignin-g-PCLs) have shown wide application potentials in coatings, biocomposites, and biomedical fields. However, the structural heterogeneity of lignin affecting the structures and properties of lignin-g-PCL has been scarcely investigated. In this study, kraft lignin is fractionated into four precursors, namely, F ins , F1, F2, and F3, with declining molecular weights and increased hydroxyl contents. Lignin-g-PCLs are synthesized via ring-opening polymerization of ε-caprolactone with lignin and characterized by GPC, FTIR, 1 H and 31 P NMR, DSC, TGA, and iGC. The mechanical properties, UV barrier, and enzymatic biodegradability of the lignin-g-PCLs are evaluated. Results show that lignin with a higher molecular weight and aliphatic OH favors the copolymerization, leading to lignin-g-PCLs with longer PCL arms. Moreover, lignin incorporation improves the thermal stability, hydrophobicity, and UV-blocking ability but reduces the lipase hydrolyzability of the copolymers. We also demonstrated that the lignin-g-PCL-coated filter paper could successfully separate chloroform–, petroleum ether–, and hexane–water mixtures with an efficiency up to 99.2%. The separation efficiency remains above 90% even after 15 cycles. The structural differences of copolymers derived from the fractionation showed minimal influence on the separation efficiency. This work provides new insights into lignin-based copolymerization and the versatility of lignin valorization.
Correction: Reductive catalytic fractionation of agricultural residue and energy crop lignin and application of lignin oil in antimicrobials
Correction for ‘Reductive catalytic fractionation of agricultural residue and energy crop lignin and application of lignin oil in antimicrobials’ by Elvis Osamudiamhen Ebikade et al. , Green Chem. , 2020, 22 , 7435–7447, https://doi.org/10.1039/D0GC02781B.
Response of Pseudomonas putida to Complex, Aromatic-Rich Fractions from Biomass
There is strong interest in the valorization of lignin to produce valuable products; however, its structural complexity has been a conversion bottleneck. Chemical pretreatment liberates lignin-derived soluble fractions that may be upgraded by bioconversion. Here, cholinium ionic liquid pretreatment of sorghum produced soluble, aromatic-rich fractions that were converted by Pseudomonas putida (P. putida), a promising host for aromatic bioconversion. Growth studies and mutational analysis demonstrated that P. putida growth on these fractions was dependent on aromatic monomers but unknown factors also contributed. Proteomic and metabolomic analyses indicated that these unknown factors were amino acids and residual ionic liquid; the oligomeric aromatic fraction derived from lignin was not converted. A cholinium catabolic pathway was identified, and the deletion of the pathway stopped the ability of P. putida to grow on cholinium ionic liquid. This work demonstrates that aromatic-rich fractions obtained through pretreatment contain multiple substrates; conversion strategies should account for this complexity.
Lignin valorization reshapes sustainable biomass refining
As the largest natural reservoir of aromatics, lignin offers significant potential for bioproduct manufacturing through advances in valorization technologies. However, the intrinsically complex structures of lignin pose significant challenges for its fractionization and downstream valorization. Overcoming challenges in lignin chemistry modification is crucial for achieving effective lignin valorization and establishing sustainable biorefinery industries. This review explores the potential of tailoring lignin reactivity to enable functional bioproduct manufacturing thereby contributing to profitable biorefining. The intrinsic characteristics of lignin are first summarized, highlighting their roles in both fractionization and valorization. The latest progress in lignin fractionation is then presented, emphasizing their potential to tailor lignin chemistry, reactivity, and processibility. Furthermore, advancements in lignin valorization are covered, recognizing that tailored lignin reactivity is key to defining bioproduct functionality. By examining these chemical mechanisms, this review sheds on the structure-function relationships between lignin and its derived products. To address the dilemma of lignin valorization and biorefineries, a promising synergistic biorefinery is proposed. This involves redesigning biomass fractionation strategies, tailoring lignin chemistry, and upgrading both carbohydrate and lignin streams across the entire biorefinery chain—from feedstock to application. Altogether, a deeper understanding of tailored lignin chemistry is crucial for decoding the reaction mechanisms in biomass processing. A synergistic biorefinery could harness lignin's intrinsic properties to improve product functionality and address key challenges, paving the way for cost-effective, sustainable biorefinery solutions.
Polymer principles behind solubilizing lignin with organic cosolvents for bioenergy
Lignin solubilization is key to a viable biorefinery because its removal leads to facile deconstruction of biomass and because the isolated lignin can serve to derive precursors of novel high-value materials. The mixing of organic solvents with water has been shown to improve biomass fractionation and lignin conversion reactions. However, generally-applicable solubilization strategies are lacking because of the remarkable variability of lignin across plant feedstocks. Here, to obtain a predictive understanding of lignin solvation, we perform molecular dynamics simulations of model lignin polymers in two mixtures of water with polar aprotic solvents: tetrahydrofuran (THF) : water and γ-valerolactone (GVL) : water. The model lignins include H-, G- and S-only homopolymers and lignins with an S : G 1 : 1 ratio. We find that a well-established theory of self-avoiding polymers in a “good” solvent describes accurately the physical conformations of all types of lignin in both solvents. As the degree of methoxy substitution increases in the homopolymers, the distributions of the lignin radius of gyration and the Flory exponent ν , which describes the lignin-solvent interactions, do not change in THF : water, while ν shifts to slightly higher values in GVL : water. We attribute this increase to the interaction between the methyl group of GVL with the lignin methoxy groups. We also find that the reduction in the lignin radius of gyration due to branching is accurately described by the Zimm–Stockmayer theory for both THF : water and GVL : water. The above findings validate the applicability of polymer physics concepts to lignin and suggest that GVL : water may have the most favorable interaction with S-lignin, whereas the interactions of THF : water with lignin are independent of lignin monomeric content.
Phase-Selective Fractionation of Lignocellulosic Biomass Using a Lignin-Based Hydrophobic Deep Eutectic Solvent Biphasic System
Lignocellulose fractionation is a critical step in biomass valorization. Herein, we report a hydrophobic deep eutectic solvent (HDES)-mediated biphasic fractionation strategy that enables the simultaneous and selective separation of cellulose, hemicellulose, and lignin in a single process. Lignin-derived HDESs composed of thymol and 2,6-dimethoxyphenol (syringol) were combined with an acidic aqueous phase to create a water-HDES biphasic system, in which lignin was preferentially extracted into the HDES phase, hemicellulose-derived sugars were selectively solubilized in the aqueous phase, and cellulose was retained in the solid residue. Using wheat straw and poplar wood as representative herbaceous and woody biomass feedstocks, the HDES-acid system exhibited strong synergistic effects, achieving delignification up to 69.8% and xylan removal up to 93.6%. Structural characterization confirmed effective disruption of the lignocellulosic matrix and increased cellulose accessibility, resulting in markedly enhanced enzymatic saccharification, with glucose yields up to 96.2% for wheat straw. This work demonstrates a sustainable and efficient HDES-based biphasic fractionation platform that enables phase-selective separation of major lignocellulosic components and provides a foundation for further development of closed-loop biorefinery processes.
Techno-economic analysis and life cycle assessment of a biorefinery utilizing reductive catalytic fractionation
Analysis of a promising lignin-first biorefining technique, reductive catalytic fractionation, provides useful metrics for cost and sustainability to guide researchers toward critical areas for improvement.
Lignin-Derived Phenolic Compounds and Water Are Effective Cosolvents for Reductive Catalytic Fractionation
Reductive catalytic fractionation (RCF) is an effective lignin-first biorefining method to extract lignin as a stabilized oil from lignocellulosic biomass. To realize RCF at scale, process modeling has shown that minimizing the use of exogenous organic solvents is critical. To this end, here we investigate the ability of lignin-derived monomers to act as either solvents or cosolvents for RCF. We begin by examining the influence of lignin-derived aromatic compounds (4-propylguaiacol, 4-propylphenol, and propylbenzene) on RCF monomer yields and subsequently extend our analysis to mixtures of 4-propylguaiacol and either methanol or water. We demonstrate that 4-propylguaiacol is an effective solvent for lignin extraction and depolymerization during RCF, especially when used in combination with water as a cosolvent. Cosolvent mixtures of 4-propylguaiacol and water enable up to 81% lignin extraction, monomer yields up to 25 wt %, and postreaction phase separation. However, unlike methanol, water as a cosolvent fails to inhibit aromatic ring hydrogenation when conducted over Ru/C as a catalyst, potentially leading to excess hydrogen consumption in a process utilizing this approach. Nonetheless, these results suggest a promising strategy for eliminating external organic solvents from RCF by utilizing mixtures of lignin-derived compounds and water as alternative extraction solvents.
Tabulated data for Lignin-Derived Phenolic Compounds and Water Are Effective Cosolvents for Reductive Catalytic Fractionation
Reductive catalytic fractionation (RCF) is an effective lignin-first biorefining method to extract lignin as a stabilized oil from lignocellulosic biomass. To realize RCF at scale, process modeling has shown that minimizing the use of exogenous organic solvents is critical. To this end, here we investigate the ability of lignin-derived monomers to act as either solvents or cosolvents for RCF. We begin by examining the influence of lignin-derived aromatic compounds (4-propylguaiacol, 4-propylphenol, and propylbenzene) on RCF monomer yields and subsequently extend our analysis to mixtures of 4-propylguaiacol and either methanol or water. We demonstrate that 4-propylguaiacol is an effective solvent for lignin extraction and depolymerization during RCF, especially when used in combination with water as a cosolvent. Cosolvent mixtures of 4-propylguaiacol and water enable up to 81% lignin extraction, monomer yields up to 25 wt %, and postreaction phase separation. However, unlike methanol, water as a cosolvent fails to inhibit aromatic ring hydrogenation when conducted over Ru/C as a catalyst, potentially leading to excess hydrogen consumption in a process utilizing this approach. Nonetheless, these results suggest a promising strategy for eliminating external organic solvents from RCF by utilizing mixtures of lignin-derived compounds and water as alternative extraction solvents. This is the tabulated data for the paper
Implementation and evaluation of multi-dual mode counter-current chromatography in the CUP Modeler software
Counter-current chromatography (CCC) is a separation technique that utilizes immiscible solvent pairs as stationary and mobile phases, which imparts numerous benefits compared to solid-liquid chromatography including the ability to treat either the more-dense or less-dense solvent layer as the mobile phase. Multi-dual mode (MDM) is a CCC elution mode capable of improving the separation of closely eluting compounds by alternating upper- and lower-layer solvent flows in opposing directions within the same separation. While some effort has been made to model MDM, implementation of these models in experimental design has yet to be widely adopted. Accordingly, we further developed our previously published cell utilized partitioning (CUP) model to include MDM predictions with CCC and packaged the full suite of CUP modeling capabilities into a user-friendly, open-source tool called the CUP Modeler. The mathematical model for MDM CCC was derived and validated with experimental separation of ethyl guaiacol (EG) and ethyl phenol (EP), two compounds that co-elute in our previously demonstrated reductive catalytic fractionation (RCF) lignin monomer isolation method. The developed MDM model provided insights into the effect of multiple operating parameters - including stationary phase retention, flow rate, column efficiency, feed concentration ratio, selectivity factor, and solute distribution ratios - on the separation yields, productivity, and purities. Our model agreed with prevailing understanding of MDM but also revealed new insights including that the ideal distribution ratios for co-eluting solutes to be separated by MDM is between 1.1 and 1.5, with the lower value ideally close to 1.25. Overall, this work provides fundamental insights for MDM process design and enables broader adoption of general liquid-liquid chromatography with a new, open-source user-friendly interface.